Universal Scientific WM-BB-AG-01 801.11b + Bluetooth Module User Manual WM BB AG 01 2 4 2004 02 23
Universal Scientific Industrial Co., Ltd. 801.11b + Bluetooth Module WM BB AG 01 2 4 2004 02 23
Users Manual Revision 2
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 414681 |
| Application ID | tPDPT3DtoubDa/WSlZ6rUg== |
| Document Description | Users Manual Revision 2 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 69.4kB (867535 bits) |
| Date Submitted | 2004-04-15 00:00:00 |
| Date Available | 2004-03-18 00:00:00 |
| Creation Date | 2004-02-23 18:22:06 |
| Producing Software | Acrobat PDFWriter 5.0Windows NT ª© |
| Document Lastmod | 2004-04-15 22:54:35 |
| Document Title | WM-BB-AG-01-2.4_2004-02-23_.doc |
| Document Creator | WM-BB-AG-01-2.4(2004-02-23).doc - Microsoft Word |
| Document Author: | Administrator |
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device is intended only for OEM Integrators. The OEM integrator should be aware of the following important issues. Labeling of the End Product The end product integrate this module has to be clearly identified on the label that this end product contain an FCC approved RF module. The format of such statement could containTx FCC ID: IXMWM-BB-AG-01 or similar. could be " Contains Transmitter with FCC ID: IXMWM-BB-AG-01" or similar. Integration Note a) This module is authorized under limited module approval specified to mobile host equipment. So, the antenna must be installed such that 20cm is maintained between the antenna and users. b) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emission, PC peripheral requirements, etc.) IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations, general purpose PCMCIA or similar cards, or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product (including the transmitter) and obtaining a separate FCC authorization. 802.11b+Bluetooth COMBO SiP Module WM-BB-AG-01 Data Sheet www.usi.com.tw Feb. 2004, Rev 2.4 Introduction The USI 802.11 Wireless SiP module WM-BB-AG01 which refers as “COMBO SiP module” is a full small size module that provides full function of 802.11b and Bluetooth class 2 on a 22*29 mm tiny module via 60 pins board to board connector. This multi- functionality and board to board physical interface provide system users the maximum flexibility including system feature and system integration. WM-BB-AG-01 is approved as one of USI embedded Wi-Fi module product lines. There are two product variants of WM-BB-AG-01 by depopulating either 802.11b or Bluetooth to be a single module which provided better cost-feature on system with single design-in effort. The small size design (22*29*3.5 mm), low power consumption (Tx 330 mA) and excellent radio performance make it the best solution which is suitable for OEM customers who require embedded 802.11b Wi-Fi plus Bluetooth features, such as, wireless PDA, barcode scanner, mini-printer, VoIP phone etc. Features For the hardware features, Agere 802.11 chipset solution is adopted for 802.11b, and CSR BlueCore 02-ROM for Bluetooth. Two antenna connectors provide antenna connectivity for each func tion. In additional to the classic radio design, physical signaling between Bluetooth and 802.11b functional block provides the best performance when Bluetooth and 802.11b function at the same time. Small size suitable for low volume system integration. Low power consumption, extend battery life. 2.412 – 2.484 GHz frequency band. Support hardware signaling Easy for integration into mobile and handheld device with flexible system configuration and antenna design. For the software and driver development, USI provides extensive technical document and reference software code for system integration. Hardware evaluation kit and development utility will be released base on listed OS and processors to OEM customers under agreement for development. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b + Bluetooth COMBO SiP Module v 2.4 OEM Deliverables • • WM-BB-AG-01 with packing Test Platform includes application (PDA ), software utilities which support customers for integration, performance tests, and homologation. Temperature and Humidity Operating Temperature Non Operating Temperature Humidity Range 0° to 60° Celsius -10° to 70° Celsius 20% to 90%( Non-condensing, relative) Voltage and Current Power supply for the WM-BB-AG-01 will be provided by the host via the board to board connector. Voltage Operating Voltage Voltage Ripple Current (Typical) Continuous Transmit Continuous Receive Sleep Mode 3.3 Volt (Typ.), Max 3.6V, Min 3.15V +/- 2%(Max value not exceeding operating voltage) 340 mA (Both 802.11 and BT in transmit mode) 230 mA (Both 802.11 and BT in receive mode) 16 mA (Both 802.11 and BT in sleep mode) Wireless Specification The WM-BB-AG-01 complies with the following features and standards; Features WLAN Standards Bluetooth Antenna Connector Coexistence Frequency Band Description IEEE 802 Part 11b (802.11b) Bluetooth TM 1.1 Two antenna connectors support 802.11b and BT one for each. Hardware signaling 2.402– 2.484 GHz LED Specification The WM-BB-AG-01 have 2 LED’s (output) via 60 pins connector for feedback to the user on the current WLAN and Bluetooth activity state with individual LED. The signaling will reflect status / activity as described in the table below. The signal is provided via the board to board connector with the following pin assignment. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b + Bluetooth COMBO SiP Module v 2.4 Pin No 42 55 Pin description WLAN_LED BT_LED Function description Link Activity of Wireless LAN Link Activity of Bluetooth The LED code and related status of the wireless module are listed below: WLAN_LED BT_LED Radio on and no activity (when device is in scan mode) Blinking Blinking Radio on and activity in each radio Blinking Blinking Off Off Radio off Cycle Time LED on time: 200ms LED off time: 2000ms LED on time: 100ms LED off time: 400ms 802.11b Radio Specification The radio specification is compliant with the SPEC of 802.11b. Features Frequency Band Number of Selectable Channels Modulation Supported Rates Maximum Receive Level Output Power Antenna Connector Description 2.412 – 2.484 GHz (2.4 GHz ISM Band) 14 channels DSSS (Direct Sequence Spread Spectrum), DBPSK, DQPSK, CCK 1,2, 5.5 and 11 Mbps - 10 dBm (with PER < 8%) 13.5 dBm +-1.0 dB One Hirose W.FL – R –SMT(10) RF connector 802.11b Radio Characteristics Receive Sensitivity - 82 dBm - 85 dBm - 88 dBm - 91 dBm * Under normal operation at room temperature. Data Rates 11 Mbps 5.5 Mbps 2.0 Mbps 1.0 Mbps All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b + Bluetooth COMBO SiP Module v 2.4 Bluetooth Radio Specification The Radio specification is compliant with the Bluetooth v1.1 class 2 specification Features Frequency Band Number of Channels Modulation Antenna Connector Description 2.402 – 2.484 GHz 79 channels FHSS (Frequency Hopping Spread Spectrum) One Hirose W.FL –R –SMT(10) RF connector Bluetooth Radio Characteristics Features Maximum Receive Level Output Power Sensitivity Description 0 dBm(Min) , 3dBm (typical) 3 dBm (typical) , 6 dbm (Max) -81 dbm @ 0.1% BER @ 25 ° Celsius ( Typical ) Compatibility and Interoperability Wi-Fi Logo Wi-Fi certification is limited and dependent on the capability and application of the host system. WHQL Compliance N/A BQB Compliance WM-BB-AG-01 is verified and proved BQB certificated. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b + Bluetooth COMBO SiP Module v 2.4 Mechanical Dimensions Dimensions: 22 mm x 29 mm x 3.5 mm (excluding RF cable assembly) Shock and Vibration The WM-BB-AG-01 has been developed for incorporated into other devices. No shock and vibration tests for this module has been performed. Configuration Users don’t need to configure it. The CIS and MAC Address and Bluetooth ID address will be loaded during production of the WM-BB-AG-01 (RTS). Security WEP 64/128 bits. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b + Bluetooth COMBO SiP Module v 2.4 Functional Block Diagram A simplified block diagram of the WM-BB-AG-01 is depicted in the picture below. Host Interface The host interface will be compatible with CompactFlash (PCMCIA) standard, 16 bit I/O bus. Signals which are not used won’t be routed to the physical interface (connector). The host interface of SiP Combo is compliant with UART interface. For the connector, high reliability connectors will be used. On Board connector Molex SD53794-0608 [Socket, 60 pins, with positioning protection, stack height which is able to support 1.5 mm. sd537941.pdf sd537942.pdf All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b + Bluetooth COMBO SiP Module v 2.4 Host System: Molex SD54037-0607 [Header, 60 pins, with positioning protection, stack height 1.5mm] sd540371.pdf Pin Definition [ … ] means optional function of the pin. PD : Signal pull down internally in the chip by 20K ohm register while initialization. PU : Signal pull up internally in the chip by 20K ohm register while initialization. WPD: Signal pull down internally in the chip by 1Mohm register during initialization WPU: Signal pull up internally in the chip by 1Mohm register during initialization 5VT: 5 Volt tolerance pin xxx_B : Signal pins end with _B are “active Low” Pin Definition Number WM-BBAG-01 Draft Description Type CF+ interface GND GND GND D03 HD3 D04 HD4 D05 HD5 D06 HD6 D07 HD7 -CE_1 HCE1_B A10 A10 -OE HOE_B 10 A09 HA9 Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Card Enable1 is driven by the host system and is used as select strobe in both I/O and memory mode. Enables even numbered address bytes. ADDRESS BUS lines driven by the host system which enables addressing of 0.5K address range within HERMES II. The pin is open in B2B module. OUTPUT ENABLE is driven by the host during a memory Read Access. ADDRESS BUS lines driven by the host system which enables addressing of 0.5K address range within HERMES II. This address range is mainly used for accessing the CIS in Memory Mode. Signal HA0 is not used in word access mode. O, PD, 5VT, 4mA Databus O, PD, 5VT, 4mA Databus IO, PD, 5VT, 4mA Databus IO, PD, 5VT, 4mA IO, PD, 5VT, 4mA Input, PU, 5VT N/A Input, PU,5VT Input, PD,5VT All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b + Bluetooth COMBO SiP Module v 2.4 11 A08 HA8 12 A07 HA7 13 VCC VCC_WLAN 14 A06 HA6 15 A05 HA5 16 A04 HA4 17 A03 HA3 18 A02 HA2 19 A01 HA1 20 A00 HA0 21 D00 HD0 22 D01 HD1 23 D02 HD2 ADDRESS BUS lines driven by the host system Input, PD,5VT which enables addressing of 0.5K address range within HERMES II. This address range is mainly used for accessing the CIS in Memory Mode. Signal HA0 is not used in word access mode. ADDRESS BUS lines driven by the host system Input, PD,5VT which enables addressing of 0.5K address range within HERMES II. This address range is mainly used for accessing the CIS in Memory Mode. Signal HA0 is not used in word access mode. Power, 3.3V_WLAN Input ADDRESS BUS lines driven by the host system which enables addressing of 0.5K address range within HERMES II. This address range is mainly used for accessing the CIS in Memory Mode. Signal HA0 is not used in word access mode. ADDRESS BUS lines driven by the host system which enables addressing of 0.5K address range within HERMES II. This address range is mainly used for accessing the CIS in Memory Mode. Signal HA0 is not used in word access mode. ADDRESS BUS lines driven by the host system which enables addressing of 0.5K address range within HERMES II. This address range is mainly used for accessing the CIS in Memory Mode. Signal HA0 is not used in word access mode. ADDRESS BUS lines driven by the host system which enables addressing of 0.5K address range within HERMES II . This address range is mainly used for accessing the CIS in Memory Mode. Signal HA0 is not used in word access mode. ADDRESS BUS lines driven by the host system which enables addressing of 0.5K address range within HERMES II. This address range is mainly used for accessing the CIS in Memory Mode. Signal HA0 is not used in word access mode. ADDRESS BUS lines driven by the host system which enables addressing of 0.5K address range within HERMES II. This address range is mainly used for accessing the CIS in Memory Mode. Signal HA0 is not used in word access mode. ADDRESS BUS lines driven by the host system which enables addressing of 0.5K address range within HERMES II. This address range is mainly used for accessing the CIS in Memory Mode. Signal HA0 is not used in word access mode. Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE Input, PD, 5VT Input, PD, 5VT Input, PD, 5VT Input, PD, 5VT Input, PD, 5VT Input, PD, 5VT Input, PD, 5VT IO, PD, 5VT, 4mA IO, PD, 5VT, 4mA IO, PD, 5VT, 4mA All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b + Bluetooth COMBO SiP Module v 2.4 24 -IOIS16 HIOIS16_B 25 -CD2 CD2 26 N/A 27 bus. HD[15:0] are used to access the MODULE MAC Host Interface register Control signal to enable engineer testing mode Out, 6mA,5V T Out, 6mA, 5VT. TXD_B Normal operation, this pin is functionally for card detection. UART CMOS output data line N/A RTS_B UART CMOS output signal, request to sent Output ,WPU, 1µA 28 N/A N/A NA No connection 29 N/A VCC_WLAN Power_WLAN Input 30 GND GND 31 GND GND 32 D10 HD10 IO, PD, 5VT, 4mA 33 D09 HD9 34 D08 HD8 35 -STSCHG HSTSCHG_B 36 -SPKR N/A Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Inp ut/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register STATUS CHANGE indication to the host. This signal gets active when one of the bits in the PRR or CSR registers are set N/A 37 -REG HREG_B Input, PU, 5VT 38 -INPACK HINPACK_B 39 -WAIT HWAIT_B 40 RESET HRESET ATTRIBUTE MEMORY SELECT is driven by the host system and is used to access the Attribute Memory INPUT ACKNOWLEDGE is driven by HERMES II. Is asserted when the device is selected and the device is responding to an I/O Read command. HWAIT_B is driven by HERMES II and allows for extending the memory or I/O cycle Used to asynchronously reset the complete Module 41 -VS2 VS2_B Voltage sense signal Output , 5VT 4mA 42 N/A WLAN_LED_B Output, 4mA 43 N/A N/A WLAN LED control signal, driven the LED indicating the link status of WLAN Reserved pin 44 IREQ IREQ_B 45 -W E HWE_B 46 -IOWR HIOWR_B Output,WPU, 1µA IO, PD, 5VT, 4mA IO, PD, 5VT, 4mA Output, 4mA No connection Output, 2mA Output, 4mA Input, PU,5VT No connection INTERRUPT REQUEST to the host. In Memory Output, 4mA mode this pin signifies RDY/BSY_typically used during card initialization immediately after reset or power on. Indicates to the host that the device is not able to transfer data WRITE ENABLE is driven by the host during a Input, PU,5VT memory Write Access I/O Write Strobe is driven by the host and is Input, PU,5VT asserted when the host wants to write to an on-chip I/O register All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b + Bluetooth COMBO SiP Module v 2.4 I/O register 47 -IORD HIORD_B Input, PU,5VT RXD_B I/O Read Strobe is driven by the host and is asserted when the host wants to read from an onchip I/O register RF CONTROL is driven by the host system and is used to enable and disable the RF circuit block CARD ENABLE2 is driven by the host system and is used as select strobe in both I/O and memory mode. Enables odd numbered address bytes Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register Data Input/Output line constitute a bi-directional bus. HD[15:0] are used to access the MODULE MAC Host Interface register BT LED control signal which drive the LED to indicate the activity of Bluetooth UART data line CMOS input signal 48 -VS1 RF control 49 -CE2 HCE2_B 50 D15 HD15 51 D14 HD14 52 D13 HD13 53 D12 HD12 54 D11 HD11 55 N/A BT_LED_B 56 N/A 57 N/A CTS_B UART clear to sent COMS input signal Input, WPD, 1µA 58 N/A N/A N/A N/A 59 VCC VCC_BT Power 3.3V_BT Input 60 GND GND Output , 5VT Input, PU,5VT IO, PD, 5VT, 4mA IO, PD, 5VT, 4mA IO, PD, 5VT, 4mA IO, PD, 5VT, 4mA IO, PD, 5VT, 4mA Output 4mA Input, WPD, 1µA Pin 1 Pin 60 Pin 59 FIG 1: PIN 1 ASSIGNMENT AND INDICATION DRAWING All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 10 802.11 b + Bluetooth COMBO SiP Module v 2.4 Antenna Interface No antenna diversity supported on the 802.11b , neither BT on this COMBO Wireless The output impedance of the cable is 50 Ohms. Antenna Connector: Hirose W.FL-R-SMT (10) Operating System Compatibility Drivers are supported for the following OS: • Windows CE 3.0/.NET • Windows 98SE/2000/XP Reliability The WM-BB-AG-01 will guarantee a MTBF of 100,000 hours based on an ambient temperature and workload of 2,920 hours. The workload is based on a unit working for 8 hours per day, 365 days per year. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 11 802.11 b + Bluetooth COMBO SiP Module v 2.4 Packaging Design All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 12 802.11 b + Bluetooth COMBO SiP Module v 2.4 For Additional information, please contact the following: Universal Scientific Industrial Co., Ltd. Headquarters 141, Lane 351, Taiping Road, Sec. 1, Tsao-Tuen , Taiwan, Http://www.usi.com.tw Tel: + 886-49-2350876, 2325876 Fax: +886-49-3439561, 2337360, 2351093 E-mail:usi@ms.usi.com.tw All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 13
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2004:02:23 18:22:06Z Modify Date : 2004:04:15 22:54:35-03:00 Page Count : 15 Creation Date : 2004:02:23 18:22:06Z Author : Administrator Producer : Acrobat PDFWriter 5.0Windows NT ª© Mod Date : 2004:04:15 22:54:35-03:00 Metadata Date : 2004:04:15 22:54:35-03:00 Title : WM-BB-AG-01-2.4_2004-02-23_.doc Creator : Administrator Has XFA : NoEXIF Metadata provided by EXIF.tools