VIDEOTEK VT-9512TX Wireless Camera Panner User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2692065
Application ID	ozONQR2WmwOGV8tIrLssjg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.53kB (94161 bits)
Date Submitted	2015-07-26 00:00:00
Date Available	2015-07-26 00:00:00
Creation Date	2015-05-22 11:54:44
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2015-07-20 15:08:52
Document Title	Microsoft Word - Wireless Panner Instructions edited 2015
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

Wireless PannerOperating Instructions
VT-9512RX
FCC ID:2ABFHVT-9512RX
Wireless Panner Specs
1. Distance:Up to 10 meters
2. Charging power: 5V/500mA
3. Power consumption: 0.2W
4. Battery: 3.7V/2200mA
5. Remote battery
Diagram of features:
A: Power button [on panner]
B: LED light [on panner]
C: Left control button: pans to the
left [on remote]
D: Right control button: pans to the
VT-9512TX
FCC ID:2ABFHVT-9512TX
right [on remote]
E: Charging port [on panner]
Operation:
Deploy the camera:
Lower your camera to the desired depth, then position the cable in the
u-shaped channel on the bottom of the panner.
anchor the camera cable in place.
Use the retainer clip to
Open the legs of the panner and
position it above the hole in the ice.
Turn on and operate the panner:
Press and hold the power button (A) about 3-4 secondsuntil the light is on.
Press the C or D button to pan left or right.
Turn off the panner:
Press and hold the power button (A) for about 3-4 secondsuntil the light is
off.
TROUBLE SHOOTING:
1. Pairing:
Turn on the wireless panner, and quickly press the power button (A) 3 times
in 3 seconds.
Next, pressand hold either button(C or D) on the remoteuntilthe motor is
rotating to left or right. This means that the pairing is OK,and the wireless
panner can be controlled by this remote.
2. Using a new remote:
If the remote is lost, you first must order a new remote. Once you have a
new remote:
Step 1: Turn on the wireless panner, and quickly press the power button (A)
6 times in 6 seconds, the LED light will turn off automatically in 10 seconds.
Step 2: Turn the wireless panner back on and quickly press the power button
(A) 3 times in 3 seconds;
Step 3: Press and hold either button(C or D) of the new remoteuntil the
motor is rotating to left or right. This means that thepairing is OK, and the
wireless panner can be controlled by this remote.
3. Charging instruction:
1. When the panner is charging, the LED light will be pulsing slowly.
2. When it hasfully charged, the LED light will stop pulsing andalwaysbe on.
3. If the charger is disconnected during the charging process, the panner
will be turned offautomatically.
4. When the panner is working, a steadyLED light means a fully charged
battery. If the light is flickering in a pattern, the number of flickers indicates
the battery strength out of a possible 4 levels. [Example: the light
flickering in a repeating pattern of 2 indicates battery strength is 2 out of
4.
5. The LED lightflickeringvery quickly indicates the battery does not have
sufficient power.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
The device meets RF Exposure requirements without any restriction.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2015:07:20 15:08:52+08:00
Create Date                     : 2015:05:22 11:54:44+08:00
Metadata Date                   : 2015:07:20 15:08:52+08:00
Format                          : application/pdf
Title                           : Microsoft Word - Wireless Panner Instructions edited 2015
Creator                         : Administrator
Document ID                     : uuid:1982ded2-d487-4252-9d17-98c7888db9da
Instance ID                     : uuid:5ab18120-62db-4439-8a19-54f1341fe561
Page Count                      : 5
Author                          : Administrator

EXIF Metadata provided by EXIF.tools