VIEWPAKER TECHNOLOGY E270HMG ALL-IN-ONE Monitor User Manual
SHENZHEN VIEWPAKER TECHNOLOGY., LTD ALL-IN-ONE Monitor Users Manual
User manual
ďź ďź7 0 G ďź ăďźă ă ďź / ALL-IN-ONE Monitor Installation steps 1. Remove the base and back cover USER INSTALLATION MANUAL Requirements of pollution control markings on China electronic information products In order to control and reduce the environmental pollution caused by the wastes of electronic information products, promote the production and sales of low-pollution electronic information products, and protect the environment and human health, only toxic and hazardous substances contained by the products are given below according to the Regulations of the Chinese Government for Electronic Information Products Pollution Control: 1. Loosen the four screws on the base and remove the base. Toxic and hazardous substances or elements Part name Lead (Pb) Hg Cd Chromium VI (Cr(Vl) PBB PBDE Upper and lower covers Machine engine (aluminum or aluminum -magnesium alloys) Lens 2. Loosen the eight screws on the back c o v e r a n d r e m o v e t h e b a c k c o v e r. Plastic assemblies Metal parts (SECC/SPTE/SPCC) Springs(SUS/SUP) Spring sheet (fast cut phosphor bronze) Rubber assemblies Fan assemblies Base board assembly Cable and wire Power cord Power socket assemblies II. Mount the motherboard (compatible with 240x240mm ATX and below MIC ROATX/ITX/MINIITX motherboards, compatible with 60mm or below cooling modules. Metal and plastic bracket frameworks Label/Name Plate CD/Manual Mylar : It means that the content of this hazardous substance in all homogeneous materials of the part is lower than the limit value stipulated in SJ/T11363-2006. X : It means that the content of this hazardous substance in at least one homogeneous material of the component is reater than the limit value stipulated in SJ/T11363-2006 Electronic Information Product. FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help . 1. Mount the I/O board according to the figure. 2. Align the PC main-board with the screws on the motherboard and fix it with six PW M3x8 machine screws. Description of environmental service duration Duration of service of the electronic information products under normal use conditions described in the manual shall be 10 years, which includes no leakage of toxic and harmful substances that would c ause environmental pollution or harm to human body and property. The product is only applicable within an area of 2000M. Statement This is a Class A product. In a domestic environment, it may cause radio interference, in this case the user may be required to take practical measures against interference. III. Mount the independent graphics card (not applic able for models with integrated graphic cards) V. Mount the HHD 1. Insert the independent graphics card into the PC slot on the PC main-board and attach the independent gra phics card onto the graphics card bracket with a PWM 3*8 screw. 1. Fix the HHD bracket with a damping ring onto the HHD with hex step scre ws in the right direction. IV. Install the CD-ROM (built-in SATA notebook drive) 2. Align the HHD assembly with the screw holes for the HHD and fix it with screws. 1. First use a knife to cut the connecting rubber and rem ove the burrs at the six positions marked with an arro w in the figure. Product View CD-ROM 2 .Fix the CD-ROM bracket on the drive with the PM2x5 screws. Camera Power Pilot Lam HHD Pilot Lamp Function Key 3. Insert the DVD assembly into the DVD slot on the middle cover and fix it with PWB3x8 screws. Microphone Restart Reduce Brightness ON/OF Increase Brightness
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Administrator Create Date : 2014:06:07 21:37:35+08:00 Modify Date : 2014:06:07 21:37:35+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Producer : Acrobat Distiller 9.0.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Metadata Date : 2014:06:07 21:37:26+08:00 Format : application/pdf Title : <35372D37302D31573030302020D6D0D0D4C6B7C5C62B46434320B0B2D7B0CAD6B2E12E636472> Creator : Administrator Document ID : uuid:98ddacd4-51de-4d35-ba0a-4efa45c62b5e Instance ID : uuid:724b27ca-38b8-4001-b136-be308b341ffb Page Count : 1EXIF Metadata provided by EXIF.tools