VISTEON ELECTRONICS FRANCE MI Measurement Interface User Manual MI GB v4

VISTEON ELECTRONICS FRANCE Measurement Interface MI GB v4

Contents

Users Manual 2

1 MI NOTICE Johnson Controls Inc. 18, Chaussée Jules César BP 340 – OSNY 95526 CERGY PONTOISE CEDEX - FRANCE !xxxx0! 21837618-7 X0 GB.doc 02/03/06
2
3 GENERAL SAFETY PRECAUTIONS • Ensure you read the following instructions carefully. • Follow all the warnings and instructions shown on the products. The International Electrical Symbols used on the device and in this notice are explained in table 1 at the end of this document. • Disconnect the equipment from the wall socket before cleaning. Do not use cleaning fluids or aerosols. Use a slightly damp cloth for cleaning. • This equipment must only be used with the battery and mains adapter supplied by us. • These instructions contain information and warnings which must be followed by the user to ensure the equipment is used and maintained safely. • Equipment category II: 400V overvoltage class II (IEC61010-1 electrical safety). • Pollution level 2: non conducting pollution with occasional temporary conductivity caused by condensation (IEC61010-1 electrical safety). IMPORTANT To avoid the risk of electrocution: • Live components are accessible when the equipment is open. The unit must be disconnected from the power source before any operation or repair inside the unit. • Do not use the equipment if the unit or the connections are damaged. • The battery access cover must be locked during use. • Do not use the equipment in the rain. • Any operation other than replacement of the battery must be carried out by an after sales service technician who is qualified to do so and knows the risks involved.
4 • Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
5 • IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Information to User: The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Canada-Industry Canada(IC) Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device.
6Content 1- Description ........................................................................................................ 8 1-1 Probe..........................................................................................................................8 1-2 Probe supply ..............................................................................................................8 2- Use ..................................................................................................................... 9 2-1 Connection diagram.................................................................................................10 3- technical specifications ................................................................................. 11 3-1 Equipment environment...........................................................................................11 4- Maintenance .................................................................................................... 12 4-1 battery:.....................................................................................................................12 4-1-1 Removing and refitting the battery...................................................................12 4-1-2 Recharging the battery......................................................................................13 4-2 Scrapping the battery ...............................................................................................13 5- Cleaning........................................................................................................... 13 6- Accessories..................................................................................................... 13 8- International electrical symbols.................................................................... 14 7- After sales service .......................................................................................... 14
7
81- Description 1-1 Probe 1-2 Probe supply The probe may be supplied by: - The battery of the vehicle via the MI synchronization cable - The self contained battery - The mains adapter only to charge the self contained battery Power LED Communication LED Self battery contained LED Operation in progress LED USB connector to PC USB HUB output Not used Power switchMains adapter connector MI synchronization cable connector Connectors for measurements Not used
92- Use Warning When working with voltages greater than 33 V RMS, 46 V peak or 70V continuous, take care as these voltages pose a risk of electrocution. Use MI in accordance with the following instructions: • ensure it is powered only by the internal battery, • connect it to the central diagnostic unit using Bluetooth mode only, • disconnect all other USB leads, MI synchronization lead… • cover over all connector openings using the rubber covers provided for this purpose. Important To avoid damage to the MI, follow the instructions below: Use the terminals and function corresponding to the measurements to be made. In ohmmeter mode, disconnect the circuit supply before checking its resistance or continuity. Observe the temperature range for operation; do not expose the unit to heat behind a window or leave it in the cold.
102-1 Connection diagram Mains adapter cable USB cable To vehicle for taking measurementTo vehicle for Power Supply MI synchronization cable Test pins and crocodile clips To mains
113- technical specifications 3-1 Equipment environment Mains adapter: Input: 100-240V AC 1A 50-60Hz Output: 12V DC 1.67A The removable plug for the mains power distribution board is used as a breaker device for the mains power source. This mains adapter is used only to charge the MI self contained battery. MI Probe: Input: 8-16V DC Imax 2.5A Battery: Type Li Ion 3.2V 2200mAH Battery life: 1hour 30 minutes at 25°C . CONDITIONS FOR USE Temperature for operation with internal battery in place: in internal battery recharge mode: from 0°C to +45°C in "measuring" mode: from -20°C to +60°C in store: from -20°C to +45°C Temperature for operation with internal battery removed from the unit: in "measuring" mode: from -30°C to +70°C in store: from -30°C to +80°C Relative humidity: 0% to 90% Operating altitude: 2,000 m Outside of these limits, the unit is not within normal conditions of use and may not operate correctly.
124- Maintenance Any operation other than replacement of the battery must be carried out by an after sales service technician who is qualified to do so and knows the risks involved Only use the accessories and consumables supplied by us: measuring cables, connectors, spare battery. 4-1 Battery: Warning Do not reverse, incinerate or mutilate battery. This can cause toxic material or gas leakage and/or explosion. 4-1-1 Removing and refitting the battery Removal Disconnect all accessories from the MI, turn it off if it is operating, open the cover on the back of the probe and remove the battery. Refitting Fit the battery into position, connecting it without forcing it. The battery fitting polarity MUST be observed (connector is fool proofed). Refit the cover.
134-1-2 Recharging the battery The battery must ONLY be recharged using the charger integrated into the MI. Just connect the probe to the mains using the mains power adapter or to the car using the MI synchronization cable (refer to the connection diagram). Make sure you observe the recharge temperatures shown in the technical specifications. 4-2 Scrapping the battery The battery must not be thrown away. It must be returned to the manufacturer for recycling. 5- Cleaning Disconnect the power before any cleaning operation. Use a damp cloth. Do not use solvents. 6- Accessories Battery Type Li Ion 3.2V 2200mAH 218368073 MI synchronization cable 218365548 Adaptater AC/DC 218365598 Mains adapter cable xxxxx USB lead 218365556 Measurement leads red, black & blue 218374109 Tests pin red, black & blue 218374120 Crocodile clamps red, black & blue 218374117
148- International electrical symbols DC (Direct current) AC (Alternating current) AC or DC Earth ground Warning, refer to the notice for information Warning against electrical choc Double insulated 7- After sales service In the event of any problems, please contact your Johnson Controls Inc. representative. Johnson Controls Inc. Service après-vente 1, Avenue Pierre-Gilles de Gennes Z.I. des Ajeux 72400 La Ferté-Bernard France Tel.: +33 2 43 60 43 60 Fax: +33 2 43 60 43 61

Navigation menu