VTech Telecommunications 80-5735-02 900MHz/5.8GHz Cordless Phone User Manual EL42208 manual 091908 ES2 0

VTech Telecommunications Ltd 900MHz/5.8GHz Cordless Phone EL42208 manual 091908 ES2 0

User Manaul 2

6Telephone base & charger installationIf you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack. The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters.Install the telephone base and charger as shown below.NOTES:1. Use only the supplied rechargeable battery, replacement battery (part numberUse only the supplied rechargeable battery, replacement battery (part number 89-1332-00-00) or equivalent. To order a replacement battery, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.2. This power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.Getting startedTelephone line cordDSL filter (available from your DSL Internet provider)4. Plug the other end of the telephone line cord into a telephone jack.5. Plug the large end of the power adapter into an electrical outlet not connected to a wall switch.3. Route cords through slots.2. Plug one end of the telephone line cord into the telephone jack on the underside of the telephone base.1. Plug the small end of the power adapter into the power jack on the underside of the telephone base.Plug the power adapter into an electrical outlet not connected to a wall switch.Charger installationTelephone base installation
7Installation optionsThe telephone base is designed for both desktop installation and wall mount installation. If wall mounting is desired, a telephone outlet wall mounting plate with mounting studs is required. This mounting plate is available for purchase at many hardware or consumer electronics retailers and may require professional installation.Desktop to wall mount installation1. Plug the telephone line cord and power adapter into the telephone base. Bundle the telephone line cord and route cords through the slots, then secure with a twist tie.2. Plug the power adapter and telephone line cord into the wall outlets, then align the mounting studs on the telephone outlet plate with the mounting holes on the telephone base.3. Place the telephone base mounting holes just above the mounting studs, then slide the telephone base down until it is secure.12Getting started
8Installation optionsWall mount to desktop installationTo change the telephone base from the wall mount position to desktop position, make sure that you first unplug the power adapter and telephone line cord from the wall outlets before you begin.1. Slide the telephone base upwards, then pull the telephone base away from the wall off of the mounting studs.2. Unplug the power adapter and the telephone line cord from the electrical outlet and the telephone jack. 3. Plug the telephone line cord into the telephone base and telephone wall jack, then plug the power adapter plug into the telephone base and a power outlet not connected to a wall switch.12Getting started
9Battery installation & chargingInstall the battery as shown below. After installing the battery, you can make and receive short calls, but replace the handset in the telephone base or charger when not in use. For optimal performance, charge the handset battery for at least 16 hours before use. When fully charged, the handset battery provides approximately five hours of talk time or six days of standby time. If the handset has not been used for a long time or if the battery inside is completely depleted, put it on the telephone base or charger for recharging.Getting startedRECORDANNC.REMOVEMENU / SELTRANSFERStep 1Insert the battery plug as indicated, making sure that it matches the color-coded label inside the battery compartment.Step 4Charge the handset, by placing the handset face up in the telephone base. The CHARGE light on the handset should be on as soon as the handset is properly placed on the telephone base.Step 3Slide the battery compartment cover up until it clicks.Step 2Place the battery and wires inside the compartment.CHARGE light
10Getting startedBattery installation & chargingLow battery indicatorReturn the handset to the telephone base or charger to recharge when this symbol flashes and the handset beeps or when the handset screen displays LOW BATTERY.IMPORTANT INFORMATIONUse only the supplied rechargeable battery, replacement battery (part number 89-1332-00-00) or equivalent. To order a replacement battery, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.To replace the battery, press the tab and slide the battery compartment cover downwards. Lift out the old battery and disconnect it from the handset. Follow the instructions on the previous page to install and charge the new battery.LOW BATTERY10:08AM 02/14
11SettingsEach cordless handset operates independently from the other handsets. The ringer sound, ringer volume, date and time, dial mode, home area code and language must be programmed separately for each cordless handset.To customize how the handset works: 1. Press MENU/SEL in the idle mode to enter the handset main menu.2. Use CID or DIR to scroll to the desired feature.3. Press MENU/SEL to select the feature.To stop at any time, press OFF/CLEAR.LanguageTo change the language to Espanol, or Francais:1. Press MENU/SEL in the idle mode to enter the handset main menu.2. Press CID or DIR until the screen displays LANGUAGE.3. Press Press MENU/SEL. The current setting is flashing.4. Press CID or DIR to choose ENGLISH, FRANCAIS, or ESPANOL.5. Press MENU/SEL to save your selection and return to the main menu.Dial modeThe dial mode defaults to tone. If you do not have touch tone service, you will need to change the setting to pulse: 1. Press MENU/SEL in the idle mode to enter the handset main menu.2. Press CID or DIR until the screen displays DIAL MODE: and the current setting.3. Press MENU/SEL. The current setting is flashing.4. Press CID or DIR to display TONE or PULSE.5. Press MENU/SEL to save your selection and return to the main menu.LANGUAGEDIAL MODE: TONETelephone operation

Navigation menu