VTech Telecommunications 80-5735-05 Cordless Phone - Handset User Manual manual

VTech Telecommunications Ltd Cordless Phone - Handset manual

User Manual 2

16Telephone operationREMOVEREMOVEOptions while on callsVolume controlWhile on a call, press CID/-VOLUME to decrease the volume, press DIR /VOLUME+ to increase the volume.When changing the volume level, the new setting is saved. Call waitingIf you subscribe to call waiting service with your local telephone company, there will be a beep if there is an incoming call while you are already on a call. Press PHONE/FLASH to put your current call on hold and take the new call. Press PHONE/FLASHanytime to switch back and forth between calls. For more information on caller ID, see page 26.MutePress MUTE to silence the microphone. When mute is on, MIC MUTED will show on the handset screen temporarily. You will be able to hear the caller, but the caller can not hear you until you press MUTEagain to resume your conversation. When the mute function is turned off, MIC ON will show temporar-ily on the handset screen.Temporary tone dialingIf dial pulse (rotary) is selected, you can switch to touch tone dialing during a call by pressing *.This can be useful if it is necessary to send tone signals for access to answering systems or long-distance services.After you hang up or press PHONE/FLASH (to receive a call waiting call), the telephone auto-matically returns to dial pulse (rotary) service.Channel selectionDuring a call, if you hear clicks and pops, or if the speech sometimes fades, press CHAN/REMOVE on the handset to scan for a clearer radio channel between cordless handset and base.VOLUME
17REMOVEDirectoryMemory capacityThe handset directory can store up to 30 entries (including nine speed dial entries). Each entry can contain a number up to 24 digits, and a name up to 14 characters. A convenient search feature can help you find and dial numbers quickly (page 21).Timeouts and error messagesIf you pause for too long while creating an entry, the procedure will time out and you will have to begin again.If all memory locations are in use, the screen will display MEMORY FULL. You will not be able to store a new number until an existing one is deleted.PAT WILLIAMS5551234MEMORY FULL
18DirectorySpeed dialYou can enter nine speed dial numbers of up to 24 digits. Each number is stored in a speed dial location (1-9). The nine speed dial numbers on the handset will be automatically added to the handset directory.Press and hold a dial pad key (1-9) and then pressPHONE/FLASHcan easily dial these telephone numbers. You can also make existing directory entries into speed dial entries.To enter a speed dial number1. Press MENU/SELECT.2. Press CID or DIR until the screen displays SPEED DIAL.3. Press MENU/SELECT.4. Press a dial pad key (1-9) to select a speed dial location.5. Enter a name up to 14 characters (page 19), then press MENU/SELECT.6. Enter a telephone number up to 24 digits (page 21), then press MENU/SELECT.7. Choose distinctive ringing (N or Y) by pressing CID or DIR . If you choose yes (and if you have caller ID service), a different ringing style will alert you when this person calls.8. Press MENU/SELECT to store the number. You'll hear a confirmation tone.To call a speed dial numberTo use speed dialing, press and hold a dial pad key (1-9) to display the number and name stored in that speed dial location, then press PHONE/FLASHto dial.To edit or delete a speed dial numberPress and hold a dial pad key (1-9) to display the entry you want. Press MENU/SELECT, then press CID or DIR until the option you want is dis-played (page 22).NOTE: The speed dial feature occupies up to nine of the thirty memory locations in the directory. For example, if there are only five speed dial entries, then up to 25 entries can be stored in the directory. If there are already 30 entries in the directory, no new direc-tory and speed dial entries can be stored in memory until some of the existing ones are deleted.1. MENU/SELECT2. CID or DIR3. MENU/SELECT(Pages 19-20).4.NOTE: You can con-vert any directory entry into speed dial entry (page 22).DIRECTORY SPEED DIALENTER 1-9ENTER NAME01
19DirectoryNew directory entriesTo enter a name• Press MENU/SELECT twice.• The screen will show ENTER NAME.• Enter the name (up to 14 alphanumeric charac-ters) of the person using the table below.• Use DIR to advance to the next space to the right, or use CID then CHAN/REMOVEto delete a mistake.• When finished entering the name, press MENU/SELECT.Each press of a particular key causes characters to be displayed in the following order:Options while entering names:• Press DIR to move the cursor to the right. Press DIR twice to enter a space.• Press CID then CHAN/REMOVE to erase letter(s) if you make mistake(s).• Press # repeatedly to enter an ampersand (&), apostrophe ('), comma (,) hyphen (-), period (.), or pound sign (#).• When finished, press MENU/SELECT.3.2. MENU/SELECTNOTE: If all memory locations are in use, an error tone will sound when you attempt to enter a number. This means the memory is full, and you will not be able to store a new number until you delete an existing one.1. MENU/SELECTDIRECTORY ENTER NAMEPAT JOHNSON_
20DirectoryNew directory entriesTo enter a numberUse the dial pad keys to enter up to 24 digits. When the number is complete, press MENU/SELECT.Options while entering numbers:• Press CID then CHAN/DELETE to erase digit(s) if you make mistake(s).• Press REDIAL/PAUSE to enter a four-second dialing pause. A P will be inserted.• When finished entering the telephone number, press MENU/SELECT to confirm.To assign a distinctive ringPress CID or DIR to select Y (if you want to assign a distinctive ring tone) or N (for a normal ring pattern). If you choose yes (and if you have caller ID service), a different ringing style will alert you when this person calls.Press MENU/SELECT to choose the desired option and store this entry in the directory.AD appears in the display of each entry that has been assigned a distinctive ring.4. MENU/SELECT5.6. MENU/SELECT7. MENU/SELECTENTER NUMBERPRT JOHNSON5556789_ DISTINCT RING? N5556789
21DirectoryDirectory searchFollow the steps on the left to browse through the directory or search to find a specific entry. You can press OFF/CLEAR anytime to exit the directory.To browse through the directoryTo browse, press DIR then press CID or DIRto scroll through all entries one by one. AD appears in the display of each entry that has been assigned a distinctive ring (page 20).NOTE: When reviewing directory entries, all entries (including those in the directory and in the speed dial) are dis-played in alphabetical order. The entries in the speed dial are identified by its speed dial number (01-09) in the lower right corner of the screen.To search alphabeticallyTo shorten your search, press DIR then use the telephone dial pad keys to enter the first letter of a name, then press DIR to scroll forward until you find the desired name.If you have more than one name entry that begin with the same letter, it is necessary to scroll through all the names beginning with that letter before see-ing names that begin with the next letter. Press dial pad keys once for the first letter, twice for the second, three times for the third, as shown on page 19.For example, if you have name entries JENNIFER, KEVIN and LINDA in your directory, pressing the dial pad key 5(JKL) once will show JENNIFER,twice KEVIN, three times LINDA.NOTE: When searching alphabetically and you press a dial pad button, if there are no entries beginning with the let-ters on that button, the handset will show NO DATA.1. DIR2. DIRDIRTo scroll name by nameTo display first entryTo search alpha-betically-OR-DIRECTORY ADAM5551234BETH 5554321JOHN5550123
22DirectoryTo change or dial entriesWhen any entry is displayed, press MENU/SELECTto see options. Press CID or DIR to highlight the option you want (blinking text), then press MENU/SELECT again to select it.To edit an entryWhen EDIT is blinking, press MENU/SELECT. You can change the name and number (or distinctive ring setting on the cordless handset) by following the steps described on pages XX.To delete an entryPress CID or DIR until DEL is blinking, then press MENU/SELECT to display a confirmation screen of ERASE? N Y.You can press CID or DIR to alternate between N or Y to determine:• When the Y blinking, press MENU/SELECT to delete the entry.• When the N blinking, press MENU/SELECT to cancel the procedure. To make an entry into a speed dial entryPress CID or DIR until SPEED is blinking, press MENU/SELECT, then dial a memory location (1-9) to transfer this entry to your speed dial directory.NOTE: If you use a memory location that is already assigned to a different entry in the directory, that entry will remain in the directory, but will no longer be a speed dial number.To dial a displayed numberWhen any directory entry is displayed, pressPHONE/FLASH or to dial the displayed number.1. DIR2. DIR3. MENU/SELECTDIRDIRPress MENU/SELECT to choose blinking optionDIRECTORYADRM5551234SPEED EDIT DEL5551234SPEED EDIT DEL5551234SPEED EDIT DEL5551234
23REMOVECaller ID summaryInformation about caller ID with call waitingThis product has a caller ID function with call waiting feature which works with service from your local telephone company.Caller ID with call waiting lets you see the name and telephone number of the caller before answering the telephone, even while on another call.It may be necessary to change your telephone service to use this feature. Contact your telephone company if: • You have both caller ID and call waiting, but as separate services (you may need combined service).• You have only caller ID service, or only call waiting service.• You do not have any caller ID or call waiting services.This product can be used with regular caller ID service, or this product’s other features can be used without subscribing to either caller ID or combined caller ID with call waiting service.There are fees for caller ID services. In addition, services may not be available in all areas.Depending on your service, you may see the caller’s number or the caller’s name and number. This product can provide information only if both you and the caller are in areas offering caller ID service and if both telephone companies use compatible equipment. The time and date are sent by the telephone company along with the call information.CHRISTINE SMITH10:08AM02/14908-555-0100
24Caller ID operationREMOVECaller ID summaryHow caller ID works If you subscribe to caller ID service provided by your local telephone company, information about each caller will be displayed between the first and second ring.Information about the last 30 incoming calls is stored in the call summary. You can review the call summary to find out who has called, return the call, or copy the caller’s name and number into direc-tory.When the call summary is full, the oldest entry is deleted to make room for new incoming call infor-mation.If you answer a call before the information appears on the screen, it will not be saved in the call sum-mary.About names Names of callers will be displayed only if the infor-mation is provided by your local telephone com-pany. If the incoming telephone number exactly matches a telephone number in your directory, the name that appears on the screen will match the corre-sponding name in your directory. For example: If Christine Smith calls, her name will appear as CHRIS if this is how you entered it into your directory.CHRISTINE SMITH10:08AM02/14908-555-0100Caller’s nameCaller’s phone numberTime of callCall number of call summaryAppears when the call is missed and un-reviewed.CHRISTINE SMITH10:08AM02/14908-555-010002Date of callNOTES:1.Caller ID features will work only if both you and the caller are in areas offering caller ID service, and if both telephone companies use compatible equipment.2. The number shown by your caller ID will be in the for-mat sent by the telephone company. The telephone company usually delivers 10-digit telephone numbers (area code plus telephone number). If the telephone number of the person call-ing does not exactly match a number in your directory, the name will appear as deliv-ered by the telephone com-pany. For example if the tele-phone company includes the area code and the directory number does not, the name will appear as delivered by the telephone company.
25Caller ID operationREMOVECaller ID summaryThere are also occasions when other information or no information is displayed for various reasons:On-screen message ReasonPRIVATE NAME Caller prefers to remain anony-mous.PRIVATE CALLER Caller name and telephone number not revealed at caller's request.UNKNOWN NAME Your local telephone company is unable to determine the caller's name.UNKNOWN CALLER Your local telephone company is unable to determine the caller's name and telephone number. Calls from other countries may also generate this message.Missed callsWhen the handset is in idle mode and have calls that have not been reviewed, its screen will show XX MISSED CALLS.Any entries which have not been reviewed will be counted as MISSED CALLS when the telephone is idle. Each time a call summary entry marked NEW is reviewed, the number of missed calls decreases by one. If there are too many missed calls and you don’t want to review them one by one, but still want to keep them in the call summary, press and holdOFF/CLEAR for two seconds when the handset is idle. All the entries in the caller ID summary will be considered old (have been reviewed), and the missed calls counter is reset to 0.CHRISTINE SMITH10:08AM02/14908-555-010002 MISSED CALLS10:08AM02/14
26Caller ID operationTo review the call summaryThe call summary displays the caller ID in reverse chronological order, with the latest one (the one with the highest number) first.When the telephone is not in use, press CID to display information about the most recent caller.To review your call summaryPress CID to scroll backward (display older calls) or DIR to scroll forward (display newer calls). The highest call number is the most recent call received.Each un-reviewed caller ID entry in the call summa-ry will be designated NEW until you have reviewed it. After all calls have been reviewed, the NEW will be disappeared.To return a callPress PHONE/FLASHto call the number currently displayed.NOTE:If the number displayed is not in the correct format, see Dialing options for detail.Dialing optionsCaller ID numbers may appear with an area code that may not be required for local calls. If the number displayed is not in the correct for-mat, you can change how it is dialed. Press #repeatedly to see dialing options. With each but-ton press, a new option will be displayed. PressPHONE/FLASH to dial when the number appears in the proper format for your area.The various dialing options are:908-555-01001-908-555-0100555-01001-555-01001. CID2. CID3.PHONE/FLASHTo dial this number-OR-PAT JOHNSON10:08AM02/14908-555-0100CHRIS WILLIAMS10:08AM02/14908-555-12341.2.3.4. #PAT JOHNSONPAT JOHNSONPAT JOHNSONPAT JOHNSON10:08AM02/14908-555-01000310:08AM02/141-908-555-01000310:08AM02/14555-01000310:08AM02/141-555-010003##CIDCIDPAT JOHNSON10:08AM02/14908-555-0100030203PHONE ON 00:109085555678
27Caller ID operationDelete call summary entriesTo delete a single call summary entryPress CID to display the latest caller ID listing. Use the CID or DIR keys to find the entry you want to delete, then press CHAN/REMOVE. When the entry is deleted, the next oldest record is displayed.To delete all call summary entriesTo clear your call summary completely, press and hold CHAN/REMOVE while the telephone is idle (not in use). This will display a confirmation screen ask-ing if you want to erase all entries in the caller ID summary. If you select yes, the call summary will be cleared and the screen will return to normal standby display, and the missed calls counter is reset to 0.NOTE: When there are already 30 entries in the caller ID memory, the next incoming call will automatically cause the old-est entry to be deleted from the caller ID memory.1. CID2. CID3. CHAN/REMOVE-OR-1.2. DIR3. MENU/SELECTCall summary clearedMARK CLAYTON10:08AM02/14908-555-567801CHRIS WILLIAMS10:08AM02/14908-555-123402PAT JOHNSON10:08AM02/14908-555-01000327 MISSED CALLS10:08AM02/14ERASE ALL N YERASE ALL N Y10:08AM02/14Press and holdCHAN/REMOVE
28Caller ID operation2. MENU/SELECT thenCID or DIR3. MENU/SELECT6. MENU/SELECTAdd entries to the directoryWhen any caller ID is displayed, follow the steps on left to enter it into your telephone directory.Both the caller’s name and the telephone number will be entered as they appear in the call sum-mary. At steps 3-4, you can make any changes to the name or number by pressing CHAN/REMOVE to erase characters, then use the dial pad keys to enter the correct information (see pages 19-20 for instructions).When the number is stored, the screen returns to the call summary display. The entry copied to your telephone directory remains in the call summary until deleted.1. CIDEntry added to phone directoryEdit name as desired4. MENU/SELECTEdit number as desired5. MENU/SELECTPAT JOHNSON10:08AM02/14908-555-010003DIAL PROGRAM10:08AM02/14908-555-010003PAT JOHNSON10:08AM02/14908555010003PAT JOHNSON10:08AM02/149085550100_03DISTINCT RING? N10:08AM02/14908555010003PAT JOHNSON10:08AM02/14908-555-010003
29Answering system operationMessage capacityThe answering system can record up to 95 mes-sages depending on the length of each message. Individual messages can be up to four minutes, and total maximum recording time is 15 minutes. Messages will remain available for replay until you delete them.Voice promptsEach time you press any answering system key, the answering system uses voice prompts to guide you.Message counterNumber of messages (or dur-ing playback, message number currently playing)Press repeatedly to hear setup options (page 32).Press to review or set clock (page 30).Press to review or record announcement; press again to quit (page 31).Press to turn answering system on or off (page 36).Press to delete mes-sage currently play-ing; press and hold to delete all old messages (page 33).Press to record a memo (page 34) or after press-ing ANNC. to record an outgoing announce-ment (page 31).Press to adjust play-back volume (page 33).Press to repeat message; press twice to play previ-ous message (page 33).Press to skip a mes-sage (page 33).Press to start or stop message playback (page 33).RECORDANNC.
30Answering system operation1. CLOCK.The system will announce the current clock setting, then announces “To set the clock, press CLOCK.”3. SKIP orREPEATuntil the system announces the correct day, then press CLOCK.2. CLOCK.The system will announce the current day setting, then announces “To change the day, press SKIP or REPEAT ,to change the hour, press CLOCK.”4.until the system announces the correct hour, then press CLOCK.until the system announc-es the correct minute, then press CLOCK.5.6.until the system announc-es the correct year, then press CLOCK. The system announces the current clock setting.SKIP orREPEATSKIP orREPEATSKIP orREPEATDay & time announcementsTo set day and timeBefore playing each message, the answering sys-tem announces the day and time when the mes-sage was received. Before using the answering system, follow the steps on the left to set the day, time and year, so that messages are dated correctly. If the clock is not set, before new messages are recorded, the system will announce "Time and day not set"before each message is played back.The system uses voice prompts to guide you. Each time you press SKIP or REPEAT, the day, hour, minute or year increases or decreases by one. When you hear the correct setting, press CLOCKto move to the next setting.To check day and timeYou can press CLOCK at any time to hear the cur-rent day and time without changing it.NOTES:1. You can press and hold SKIP or REPEAT to increase or decrease the minutes or years by ten.2. Caller ID provides the time and date. Set the year so that the day of the week can be calculated from the caller ID information. After you set the time once, it will thereafter be set automatically with incoming caller ID information. The time will be set automatically only if you subscribe to caller ID service provided by your local telephone company (page 23).RECORDANNC.
31Answering system operationRECORDANNC.RECORDANNC.Outgoing announcementsThe outgoing announcement is the message callers hear when calls are answered by the answering system.The telephone is factory set with an announcement. If the telephone is set up to record messages, it answers calls with “Hello. Please leave a message after the tone.” You can use this announcement, or replace it with a recording of your own voice.To play your outgoing announcementPress ANNC., you will hear "Announcement. Press PLAY or press RECORD." Then press PLAY/STOP.You will hear the outgoing announcement. Press ANNC. to exit the announcement menu. To record your outgoing announcementPress ANNC. , then you will hear "Announcement. Press PLAY or press RECORD." Press RECORDand begin speaking after hearing "Record after the tone. Press STOP when you are done." Speak facing the telephone base from about nine inches away. Press PLAY/STOP when you are done. Your recorded announcement will be played back. Press ANNC. to exit the announcement menu.Elapsed time (in seconds) will be shown in the message window when recording. You can record an announcement up to 90 seconds long. Announcements shorter than two seconds long will not be recorded.To delete your outgoing announcementPress ANNC. , then you will hear “Announcement. Press PLAY or press RECORD.” Then press PLAY/STOPto begin playback. Press DELETE during playback to delete your announcement. Press ANNC. to exit the announcement menu.When your announcement is deleted, calls will be answered with the the factory set announcement described above.1. ANNC.“Announcement. Press PLAY or press RECORD.”2.(Plays announce-ment previously recorded).-OR-PLAY/STOPElapsedrecording time (in seconds).Press to stop recording.2. RECORD“Record after the tone. Press STOPwhen you are done.”3.4.(Announcement is played back).Speak into microphone.MicrophonePLAY/STOP5. ANNC.to exit announcement record-ing.1. ANNC.“Announcement. Press PLAY or press RECORD.”
32Answering system operation1. SETUP3. SETUP-OR-2. SKIP or REPEATPLAY/STOPChanging feature optionsYou can change the answering system operation. Press SETUP repeatedly to hear each feature. When you hear the feature you want to modify press SKIP or REPEAT to change the setting. Press PLAY/STOP to confirm the setting and exit the menu.Feature options (Default settings underlined)System announces: Feature description:"Number of rings," cur-rent setting, then "To change the setting press SKIP or REPEAT; to con-tinue setup, press SETUP."Options: 2/4/6/toll saver“Base ringer,” current set-ting, then “To change the setting, press SKIP or REPEAT; to continue setup, press SETUP.”Options: high/low/off"Remote access code,"current setting, then "To change the setting press SKIP or REPEAT; to con-tinue setup, press SETUP."Options: (select a two-digit code) 19"Message alert tone,"current setting, then "To change the setting, press SKIP or REPEAT; to con-tinue setup, press SETUP."Options: on/offChoose number of rings before the system answers a call. When toll saver is active, the system answers after two rings if you have new messages, and after four rings if you have no new messages. When retrieving mes-sages from a long distance call, you may disconnect your call after three rings so that there will be no long distance charge incurred.Choose the base ringer volume between high and low level, or turn the base ringer off.Select a two-digit number (10-99) for remote access from another telephone (page 37).When on, the telephone beeps every 10 seconds when there are new messages.NOTE: Press and holdSKIPorREPEAT to increase or decrease the remote access code number by ten.until desired feature is heard (see list at right).until desired selection is heard.to set selection and move to next menu option.to set selection and exit menu.NOTES:1. The message alert tone will beep only if all the conditions below are met: Answering system is on Message alert tone setting is on Have new messages2. Press any base key (except HANDSET LOCATOR) to temporarily silence the mes-sage alert tone. If you press and hold DELETE you will delete all old messages and the message alert tone will be temporarily silenced. The message alert tone will be re-activated with the next incoming message.RECORDANNC.
33Answering system operationRECORDANNC.Message playbackPress PLAY/STOP to listen to messages. The system announces the number of messages, then begins playback.If you have new messages waiting, you will hear only the new messages (oldest first). If there are no new messages, the system will playback all messages (oldest first). Announcements• When playback begins, you will hear the total number of messages.• Before each message, you will hear the day and time it was received.• After the last message, you will hear “End of mes-sages.” If the system has less than five minutes of recording time left, you will hear the time remaining.Options during playback• Press VOLUME button to adjust the speaker volume.• Press SKIP to skip to next message.• Press REPEAT to repeat the message cur-rently playing. Press twice to hear previous message.• Press DELETE to delete the message being played back.• Press PLAY/STOP to stop playback.To delete all messagesTo delete all old messages, press and hold DELETEwhile the telephone is idle (not during a call, or during message playback).1.“You have [xx] new messages and [xx] old messages”Number of messages (or during playback, message number cur-rently playing).Message playback begins. See options at right.2.PLAY/STOP to begin or end message playback.PLAY/STOPPLAY/STOPto end message playback. NOTES:1. If F is flashing in the mes-sage window, memory is full. You will have to delete some messages before new ones can be received.2. The maximum record time is 11 minutes.3. If you receive calls when the memory is full, the telephone will ring 10 times, then answer and announce “Memory is full, enter remote access code.”4. New (unheard) messages cannot be deleted.
34Answering system operationRECORDANNC.RECORDANNC.Recording & playing memosMemos are messages you record yourself. They are saved, played back and deleted exactly like incoming messages. You can record a memo as a reminder to yourself, or leave a message for someone else if other members of your household are using the answering system.To record a memoPress RECORD. Elapsed time (in seconds) is shown in the message window as you record. You can record a memo up to four minutes. Memos less than one second will not be saved.Press PLAY/STOP to stop recording.To play back a memoPress PLAY/STOP to hear messages and memos (see page 33 for other options).1. RECORD“Record after the tone. Press STOPwhen you are done.”3.Elapsedrecording time (sec-onds).Press to stop recording.2.PLAY/STOPMicrophone“Recorded, beep,”the memo has been recorded.Speak into microphone.
35Answering system operationRECORDANNC.Message counter displaysThe message counter usually displays the total number of memos and incoming messages. See the list below for explanations of other displays in this counter.Message counter displays0 No messages.0(flashing) The clock needs to be set (page 31).1-95 Total number of messages and memos, or message number currently playing.1-95 (flashing) Total number of messages and memos. The number flashes when there are new (un-reviewed) messages.If the telephone loses power, after power is restored, the number in the message coun-ter will flash to indicate the clock needs to be set.10-99 Current remote access code while setting (page 32).1-99 (counting) Elapsed time while recording a memo (page 34) or announcement up to 90 seconds (page 31).99 (flashing) Memo recording time has exceeded the maximum counter capacity of 99 seconds.F(flashing) Memory is full. Messages must be deleted before new messages can be received.-- System is answering a call, being accessed remotely, or the clock is being set.-- (flashing) System is being setup or initialized.On (or) OF Displayed for one second when any answer-ing system setting is turned on or off.02, 04, 06, S Current number of rings while setting (page 32).1-8 Displayed for two seconds while telephone base speaker volume is being adjusted.35HI, LO, OF Displayed for two seconds while telephone base ringer volume is being adjusted.
36Answering system operationRECORDANNC. ANSWER ONuntil the system announces “Calls will not be answered.” "Beep"The system has been turned off.1. 2.Answering system modeThe answering system’s default factory setting is ON in order to answer and record messages. You can turn the answering system off, but if you do so, the answering system will not answer calls or record incoming messages.To turn the answering system offPress ANSWER ON until you hear “Calls will not be answered” and a confirmation beep. The ANSWER ON will be turned off.NOTE: If the answering system is off and someone calls, the telephone will ring 10 times then answer and announce “Please enter your remote access code.” Enter your remote access code to enter remote access mode (page 37). If you do not enter the correct remote access code, the call will be ended automatically.To turn the answering system onPress ANSWER ON until you hear “Calls will be answered” then a beep to confirm the ON setting. The ANSWER ON light will be turned on.Call screeningIf the answering system is on and the base volume is not off, you will hear the announcement and the incoming message when a call comes in.Call interceptWhile you are call screening, you can intercept the call by pressing PHONE/FLASH on the handset.-OR-ANSWER ONuntil the system announces “Calls will be answered.” "Beep"The system has been turned on.2.1.
37Answering system operation1.Remote accessA two digit security code is required to access your answering system from any touch-tone telephone. This code is 19 by default, see Changing feature options (page 32) to change it.Dial your telephone number from any touch-tone tel-ephone.2. When the system answers, enter two digit remote access code (19 unless you have changed it).3. Enter remote commands (see list at right).4. Hang up to end the call and save all undeleted messages.NOTE: If you pause for more than four seconds dur-ing remote access, you will hear a help menu listing all features and commands. If there is no command entered for another 20 seconds, the call will end automatically.Play all messages1Play new messages2Delete the message333Repeat or go back4Stop 5Skip to next message6Record announcement*7 to begin recording5to stop recordingHelp menu*5Turn system off0Turn system on0Exit8Press to hear all messages.Press to hear new messages.Press once during playback to delete current message. Press twice to delete all old messages.Press during the caller’s message to repeat the message. Press dur-ing the beginning of the day and time announcement to go back to the previous message.Press to stop any operation (stop playback, stop recording).Press to skip the current message and advance to next message.Press * 7, wait for the beep, then begin speaking. Press 5 to stop recording and hear the playback of new announcement.Press to hear list of features & commands.Press to turn off answering sys-tem. Incoming calls will no longer be answered.If off, system will answer after 10 rings. Enter your access code, then press 0 to turn the answer-ing system on.Press 8 or hang up to end the remote access call.
38AppendixRECORDANNC.Screen icons, indicator lights & tonesScreen icons & alert tonesScreen iconsBattery charging (animated display).Low battery (flashing); place handset in telephone base to recharge.Missed and un-reviewed calls.Handset alert tonesTwo short beepsDouble beep every five secondsFive beepsConfirmation tone Command completed successfully.Out of range when on the line.Low battery warning.The volume level is at the maximum or minimum setting.Telephone base tonesOne beep every 10 secondsA series of beepsMessage alert.Press VOL keys while the volume level is already at the maximum or minimum setting.REMOVERinger off.Indicator lightsANSWER ONOn when the answering system is on and ready to receive messages.06 MISSED CALLS10:08AM02/1402Microphone is muted.IN USE• On steady when the handset is in use.• Flashes quickly while an incoming call is ringing.CHARGEOn when the cordless handset is properly positioned to charge in the telephone base.
39AppendixHandset display screen messagesScreen display messagesREMOVECONNECTING . . .CONNECTING... The cordless handset is waiting for a dial tone.NEEDS CHARGING Cordless handset battery is depleted. Place the cordless handset in the base to charge the battery.BATTERY LOW Cordless handset battery is low. Place cordless handset in base to charge the battery.SCANNING... Cordless handset is scanning for a clear channel to improve sound quality.** RINGING ** There is an incoming call.** PAGING ** The cordless handset locator has been activated (the cord-less handset beep to help you locate it).XX MISSED CALLS There are missed and un-reviewed calls in your call summary.CAN'T CONNECT The handset cannot communicate with the base.MIC ONMEMORY FULLMIC MUTEDRINGER OFFThe call switches from normal call to mute.You are saving to a full directory.The call switches from mute to normal call.The cordless handset ringer is turned off.PARALLEL SET ON Another telephone on the same line is in use.
40AppendixTroubleshootingIf you have difficulty with your telephone, please try the suggestions below. For Customer Service, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.My telephone does not work at all• Make sure the battery is installed and charged correctly (page 7). For optimum daily performance, return the cord-less handset to the telephone base after use.• Make sure the power adapter is securely plugged into an outlet not connected to a wall switch.• Make sure the telephone line cord is plugged firmly into the telephone base and the modular wall jack.• Unplug the telephone’s electrical power. Wait for approx-imately 15 seconds, then plug it back in. Allow up to one minute for the cordless handset and base to synchronize.• Charge the battery in the cordless handset for at least 16 hours.• Remove and re-insert the battery. If that still does not work, it may be necessary to purchase a new battery.• Disconnect the telephone base from the modular jack and plug in a working telephone. If this telephone does not work, the problem is probably in the wiring or the local service. Call the local telephone company.BATTERY LOWis displayed on screen• Place the handset in the base for recharging.• Remove and re-install the battery and use it normally until fully discharged, then recharge the handset on the telephone base for 16 hours.• If the above measures do not correct the problem, the battery may need to be replaced.The battery does not charge in the handset or the handset battery does not accept charge• Make sure the handset is placed in the telephone base correctly. The CHARGE light on the handset should be on.• If the cordless handset is in the telephone base but the CHARGE light is not on, refer to The CHARGE light is offin this section.• It may be necessary to purchase a new battery. Please refer to the Batteries section of this user’s manual.• The telephone might be malfunctioning. Please refer to the Limited warranty section of this user’s manual for further instruction.
41AppendixThere is no dial tone• First, try all the above suggestions.• Move the cordless handset closer to the telephone base. It might be out of range.• The telephone line cord might be malfunctioning. Try installing a new telephone line cord.• Disconnect the telephone base from the telephone jack and connect a different telephone. If there is no dial tone on the telephone either, the problem is in your wiring or local service. Contact your local telephone company.The telephone does not ring when there is an incoming call• Make sure the ringer is on (pages 11-12).• Make sure the telephone line cord and power adapter are plugged in properly (page 6).• The cordless handset may be too far from the telephone base. Move it closer to the telephone base.• There may be too many extension telephones on the tel-ephone line to allow all of them to ring simultaneously. Try unplugging some of them.• If the other telephones in your home are having the same problem, the problem is in the wiring or local service. Contact the local telephone company (charges may apply).• Other electronic products can cause interference to your cordless telephone. Try installing your telephone as far away as possible from the following electronic devices: wireless routers, radios, radio towers, pager towers, cel-lular telephones, digital telephones, intercoms, room monitors, televisions, VCRs, personal computers, kitchen appliances, and other cordless telephones.TroubleshootingThe CHARGElight is off• Clean the metallic charging contacts on the cordless hand-set and telephone base each month using a pencil eraser or a dry non-abrasive fabric.• Make sure the power adapter and telephone line cords are plugged in correctly and securely.• Unplug the power adapter. Wait for 15 seconds before plugging it back in. Allow up to one minute for the cordless handset and telephone base to reset.• The telephone might be malfunctioning. Please refer to the Limited warranty section of this user’s manual for further instruction.
42AppendixTroubleshootingThere is noise or interference dur-ing a telephone conversation• The handset may be out of range. Move it closer to the telephone base.I cannot dial out • First, try all the above suggestions.• Make sure there is a dial tone before dialing. It is nor-mal if the cordless handset takes a second or two to synchronize with the telephone before producing a dial tone. Wait an extra second before dialing.• Make sure the telephone is set to the correct dial mode (pulse dial or tone dial) for the service in your area. Refer to the Settings section of this user’s manual (page 11) to set the dial mode.• If the other telephones in your home are having the same problem, the problem is in the wiring or local service. Contact your local telephone company (charg-es may apply).• Eliminate any background noise. Noise from a televi-sion, radio, or other appliances may cause the telephone to not dial out properly. If you cannot eliminate the background noise, first try muting the cordless hand-set before dialing, or dialing from another room in your home with less background noise. My phone rings but when I try to answer the call the handset screen shows CONNECTING…• The cordless handset may be too far from the telephone base. Move closer to the telephone base and try to answer the call.• Test a working telephone at the same telephone jack. If another telephone has the same problem, the problem is in the telephone jack. Contact your local telephone com-pany (charges may apply).• The telephone line cord might be malfunctioning. Try installing a new telephone line cord.• Re-install the battery and place the cordless handset in the telephone base.• Wait for the cordless handset to synchronize with the telephone base. Allow up to one minute for this to take place.
43AppendixTroubleshootingI hear other calls when using the telephone• Disconnect the telephone base from the telephone jack. Plug in a different telephone. If you still hear other calls, the problem is probably in the wiring or local service. Call your local telephone company.• Appliances or other cordless telephones plugged into the same circuit as the telephone base can cause interference. Try moving the appliance or telephone base to another outlet.• Other electronic products can cause interference to your cordless telephone. Try installing your telephone as far away as possible from the following electronic devices: wireless routers, radios, radio towers, pager towers, cellular telephones, digital telephones, intercoms, room monitors, televisions, VCRs, personal computers, kitchen appliances, and other cordless telephones.• Microwave ovens operate on the same frequency as your telephone. It is normal to experience static on your telephone while the microwave oven is operating. Do not install this telephone in the same outlet or near a microwave oven.• If your telephone is plugged in with a modem or a surge protector, plug the telephone (or modem/surge protec-tor) into a different location. If this solves the problem, re-locate your telephone or modem farther apart from each other, or use a different surge protector. • The layout of your home or office might be limiting the operating range. Try moving the base to another location, preferably a higher location for better reception.• Disconnect the telephone base from the modular jack and plug in a corded telephone. If calls are still not clear, the problem is probably in the wiring or local service. Contact your local service company (charges may apply).• Select channels four through 10 for your router (refer to the user’s manual of your router for more information).• If the other telephones in your home are having the same problem, the problem is in the wiring or local service. Contact the local telephone company (charges may apply).• Do you have DSL service? If yes, you need to have a DSL filter installed at every telephone jack that has a telephone connected to it. Contact your DSL service provider for filter information.My calls fade out or cut in and out when I am using the cordless hand-set“Time and day not set” prompts• You need to set the answering system clock (page 30).
44Appendix• If the telephone is not responding normally, try putting the cordless handset in the telephone base. If it does not seem to respond, try the following (in the order listed):1. Disconnect the power to the telephone base.2. Disconnect the battery on the cordless handset.3. Wait a few minutes before connecting power to the telephone base.4. Re-install the battery and place the cordless handset into the telephone base .5. Wait for the cordless handset to synchronize its con-nection with the telephone base. Allow up to one minute for this to take place.Common cure for electronic equipmentMy caller ID features are not working properly• Caller ID is a subscription service. You must subscribe to this service from your local telephone company for this feature to work on your telephone.• The caller may not be calling from an area which supports caller ID.• Both you and the caller’s telephone companies must use equipment which are compatible with caller ID service.• If you subscribe to DSL service, install a DSL filter to the telephone line between the telephone base and the telephone line jack. Contact your DSL service provider for filter information.The system does not receive caller ID or the system does not display caller ID during call waiting• Make sure you subscribe to caller ID with call waiting fea-tures services provided by the local telephone company. • The caller may not be calling from an area which sup-ports caller ID.• Both you and the caller’s telephone companies must use equipment which are compatible with caller ID service.• If you subscribe to DSL service, install a DSL filter to the telephone line between the telephone base and the telephone line jack. Contact your DSL service provider for filter information.TroubleshootingThe announce-ment message is not clear• When recording the announcement, make sure you speak in a normal tone of voice about nine inches from the telephone base.• Make sure there is no background noise (television, music, traffic, etc.) when recording.
45AppendixTroubleshootingThe answering system does not respond to remote com-mands• Make sure your remote access code is correct (page 37).• Make sure you are calling from a touch-tone telephone. When dialing a number, you should hear tones. If you hear clicks, then it is not a touch-tone telephone and cannot activate the answering system.• The answering system may not detect the remote access code when your announcement is playing. Wait until the announcement is over before entering the code.• There may be interference on the telephone line you are using. Press the dial pad keys firmly when dialing.The answering system does not answer after the correct number of rings• Make sure the answering system is on. When the answer-ing system is on, the red light on the ANSWER ON key should be lit.• If toll saver is activated, the number of rings changes to two when there are new messages waiting (page 32).• If the memory is full or if the answering system is off, the system will answer after ten rings. If the memory is full, you need to delete some old messages in order to make room for new messages.• In some cases, the answering system may be affected by the ringing system used by the local telephone company.The answering system does not record message• Make sure the answering system is on.• If the memory is full the system will answer after ten rings and announce “Memory full. Enter remote access code.” You need to delete some old messages in order to make room for new messages.The messages on the answer-ing system are incomplete• If a caller reaches the maximum recording time of four minutes, for each message, the system will disconnect and part of the message may be lost. • If the caller pauses for more than seven seconds, the sys-tem stops recording and disconnects the call.• If the memory on the system becomes full during a mes-sage, the system stops recording and disconnects the call.• If the caller’s voice is very soft, the system may stop recording and disconnect the call.The messages on the system are very difficult to hear• Press VOL on the telephone base to increase the speaker volume.
46AppendixImportant safety instructionsThis symbol is to alert you to important operating or servicing instructions that may appear in this user’s manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electric shock.Safety information•Read and understand all instructions in the user’s manual. Observe all markings on the product.•Avoid using a telephone during a thunderstorm. There may be a slight chance of electric shock from lightning.•Do not use a telephone in the vicinity of a gas leak. If you suspect a gas leak, report it immediately, but use a telephone away from the area where gas is leaking. If this product is a cordless model, make sure the base is also away from the area.•Do not use this product near water, or when you are wet. For example, do not use it in a wet basement or shower, or next to a swimming pool, bathtub, kitchen sink, or laundry tub. Do not use liquids or aerosol sprays for cleaning. If the product comes in contact with any liquids, unplug any line or power cord immediately. Do not plug the product back in until it has dried thoroughly.•Install this product in a protected location where no one can trip over any line or power cords. Protect cords from damage or abrasion.•If this product does not operate normally, read Troubleshooting in this user’s manual. If you cannot solve the problem, or if the product is dam-aged, refer to the limited warranty. Do not open this product except as may be directed in your user’s manual. Opening the product or reassembling it incorrectly may expose you to hazardous voltages or other risks.•If this product has user-replaceable batteries, replace batteries only as described in your user’s manual. Do not burn or puncture batteries — they contain caustic chemicals.•If this product has a three-prong (grounding) plug or a polarized plug with one wide prong, it may not fit in non-polarized outlets. Do not defeat the purpose of these plugs. If they do not fit in your outlet, the outlet should be replaced by an electrician.CAUTION: Use only the power adapter provided with this product. To obtain a replacement, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
47AppendixImportant safety instructionsEspecially About Cordless Telephones•Privacy: The same features that make a cordless telephone conve-nient create some limitations. Telephone calls are transmitted between the telephone base and handset by radio waves, so there is a possibil-ity that your cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones.•Electrical power: The telephone base of this cordless telephone must be connected to a working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the handset if the telephone base is unplugged or switched off, or if the electrical power is interrupted.•Power adapter: This power adapter is intended to be plugged into a vertical wall outlet or a floor outlet.•Potential TV interference: Some cordless telephones operate at frequencies that may cause interference to TVs and VCRs. To minimize or prevent such inter-ference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference. •Rechargeable batteries: This product contains either Nickel-Cadmium or Nickel-Metal Hydride rechargeable batteries. Exercise care in handling batter-ies in order not to short the battery with conducting material such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm. Observe proper polarity between the battery and the battery charger.•Nickel-cadmium rechargeable batteries: Must be recycled or disposed of properly. Do not dispose of in household garbage. Do not burn or puncture. Like other batteries of this type, if burned or punctured, they could release caustic material which could cause injury.The RBRC™ Seal means that the manufacturer is voluntarily participating in an industry program to collect and recycle nickel-cadmium rechargeable batteries when taken out of service within the United States. These batteries may be taken to a participating local retailer of replacement batteries or recycling center. Or you may call 1 (800) 8 BATTERY for locations accepting spent nickel-cadmium Batteries.
48AppendixImportant safety instructions•Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or puncture. Like other batteries of this type, if burned or punctured, they could release caustic material which could cause injury.The RBRC™ Seal means that the manufacturer is voluntarily participating in an industry program to collect and recycle nickel-metal rechargeable batteries when taken out of service within the United States. These batteries may be taken to a participating local retailer of replacement batteries or recycling center. Or you may call 1 (800) 8 BATTERY for locations accepting spent nickel-metal Batteries. Precautions for users of implanted cardiac pacemakersCardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR had recommended to physicians that:Pacemaker patients• Should keep wireless telephones at least six inches from the pacemaker.• Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is turned ON.• Should use the wireless telephone at the ear opposite the pacemaker.WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones.Especially about telephones answering systemsTwo-way recording: This telephone does not sound warning beeps to let the other party know that the call is being recorded. To ensure that you are in compliance with any federal or state regulations regarding recording a telephone call, you should start the recording process and then inform the other party that you are recording the call.SAVE THESE INSTRUCTIONS
49AppendixFCC Part 68 & ACTAThis equipment complies with Part 68 of the FCC rules and with tech-nical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equip-ment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request.The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company.This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.If this equipment is malfunctioning, it must be unplugged from the modu-lar jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The tel-ephone company is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the tel-ephone company is required to inform you of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper function-ing of this product. The telephone company is required to notify you if such changes are planned.
50AppendixFCC Part 68 & ACTAIf this product is equipped with a corded or cordless handset, it is hearing aid compatible.If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these loca-tions. If you do store or test emergency numbers, please:Remain on the line and briefly explain the reason for the call before hang-ing up.Perform such activities in off-peak hours, such as early morning or late evening.Industry CanadaOperation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interfer-ence, including interference that may cause undesired operation.The term ‘’IC: ‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the require-ment that the sum of the RENs of all the devices does not exceed five.This product meets the applicable Industry Canada technical specifications.
51AppendixFCC Part 15This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reason-able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer-ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more. If you choose to use a clipping device, please make sure to only use the supplied AT&T belt clip.This Class B digital apparatus complies with Canadian ICES-003.
52AppendixLimited warrantyThe AT&T brand is used under license - any repair, replacement or warranty service, and all questions about this product should be directed to: In the United States of America visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.1. What does this limited warranty cover?The manufacturer of this AT&T-branded product warrants to the holder of a valid proof of purchase (“CONSUMER” or “you”) that the product and all accessories provided in the sales package (“PRODUCT”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the PRODUCT oper-ating instructions. This limited warranty extends only to the CONSUMER for products purchased and used in the United States of America and Canada.2. What will be done if the PRODUCT is not free from defects in materials and workmanship during the limited warranty period (“materially defective PRODUCT”)?During the limited warranty period, the manufacturer’s authorized service representative will repair or replace at the manufacturer’s option, without charge, a materially defective PRODUCT. If the manufacturer repairs the PRODUCT, they may use new or refurbished replacement parts. If the man-ufacturer chooses to replace the PRODUCT, they may replace it with a new or refurbished PRODUCT of the same or similar design. The manufacturer will retain defective parts, modules, or equipment. Repair or replacement of the PRODUCT, at the manufacturer’s option, is your exclusive remedy. The manufacturer will return repaired or replacement products to you in work-ing condition. You should expect the repair or replacement to take approxi-mately 30 days.3. How long is the limited warranty period?The limited warranty period for the PRODUCT extends for ONE (1) YEAR from the date of purchase. If the manufacturer repairs or replaces a materi-ally defective PRODUCT under the terms of this limited warranty, this limit-ed warranty also applies to repaired or replacement PRODUCT for a period of either (a) 90 days from the date the repaired or replacement PRODUCT is shipped to you or (b) the time remaining on the original one-year limited warranty; whichever is longer.
53AppendixLimited warranty4. What is not covered by this limited warranty?This limited warranty does not cover:• PRODUCT that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water, or other liquid intrusion; or• PRODUCT that has been damaged due to repair, alteration, or modifica-tion by anyone other than an authorized service representative of the manufacturer; or• PRODUCT to the extent that the problem experienced is caused by signal conditions, network reliability or cable or antenna systems; or• PRODUCT to the extent that the problem is caused by use with non-AT&T accessories; or• PRODUCT whose warranty/quality stickers, PRODUCT serial number plates or electronic serial numbers have been removed, altered or ren-dered illegible; or• PRODUCT purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to products used for rental purposes); or• PRODUCT returned without valid proof of purchase (see item 6 below); or• Charges for installation or setup, adjustment of customer controls, and installation or repair of systems outside the telephone.5. How do you get warranty service?To obtain warranty service in the United States of America, call1 (800) 222-3111; In Canada, please dial 1 (866) 288-4268. NOTE: Before calling for service, please review the user’s manual - a check of the PRODUCT controls and features may save you a service call.Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the PRODUCT(s) to the service location. The manufacturer will return repaired or replaced PRODUCT under this limited warranty to you, transportation, delivery or handling charges prepaid. The manufacturer assumes no risk for damage or loss of the PRODUCT in transit. If the PRODUCT failure is not covered by this limited warranty, or proof of pur-chase does not meet the terms of this limited warranty, the manufacturer will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of products that are not covered by this limited warranty.
54AppendixLimited warranty6. What must you return with the PRODUCT to get warranty service?You must:a. Return the entire original package and contents including the PRODUCT to the service location along with a description of the malfunction or dif-ficulty; andb. Include “valid proof of purchase” (sales receipt) identifying the PRODUCT purchased (PRODUCT model) and the date of purchase or receipt; andc. Provide your name, complete and correct mailing address, and telephone number.7. Other limitationsThis warranty is the complete and exclusive agreement between you and the manufacturer of this AT&T branded PRODUCT. It supersedes all other written or oral communications related to this PRODUCT. The manufacturer provides no other warranties for this PRODUCT. The warranty exclusively describes all of the manufacturer’s responsibilities regarding the PRODUCT. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification.State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or prov-ince to province.Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the PRODUCT is fit for ordinary use) are limited to one year from date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall the manufacturer be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inabil-ity to use the PRODUCT or other associated equipment, the cost of substi-tute equipment, and claims by third parties) resulting from the use of this PRODUCT. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclu-sion may not apply to you.Please retain your original sales receipt as proof of purchase.
55AppendixTechnical specificationsRF frequency band(handset to telephone base)5857.2 MHz — 5865.9 MHzRF frequency band(telephone base to handset)912.75 MHė — 917.10 MHzChannels 30Operating temperature 32°F — 122°F0°C — 50°CTelephone base voltage(AC voltage, 60Hz)104 — 129VrmsTelephone base voltage(AC adapter output)DC7.5V @250mAHandset voltage DC3.1 — 4.3V 400mAhRechargeable battery 3.6V 400mAhModulation FMTelephone operating rangeThis cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, the handset and tele-phone base can communicate over only a certain distance - which can vary with the locations of the telephone base and handset, the weather, the layout, and the construction of your home or office.
56AppendixAAlert tones, 38Answering calls, 13Answering system, 29-37BBattery charging, 7Battery installation, 7Battery low, 7Belt clip, 10CCall waiting, 16Caller ID, 23add entries to the directory, 28delete entries, 27dial entries, 26Channel, 16Call screening,36Call intercept, 36DDelete call summary entries, 27Delete redial entries, 14Dialing,directory dialing, 22from a CID record, 26mode, 11Directory, 17dial number, 22edit entries, 22make an entry, 22search, 21DSL filter, 6EElapsed time, 13FFlash (switchhook flash), 16HHands-free use, 13Handset locator, 15Headset, 10IIncoming call summary, 24Incoming calls, answering, 13Indicator lights, 38LLast number redial, 14MMaking calls, 13Menus, 2Message playback, 33Missed calls, 25Mute, 16NNames,search for, 21PPower adapter, 6QQuick reference guide, 2-3RReceiving calls, 13Recharging, 7Redial, 14Ring silencing, 14Ringer sound, 12Ringer volume, 11SScreen display messages, 39Search for names, 21Speakerphone, 13TTechnical specifications, 55Temporary tone dialing, 16Troubleshooting, 40VVolume control, 16Voice prompts, 29Index
AppendixRemote access wallet cardUse the wallet card below to help you remember commands to control your answering system from any touch tone telephone.Fold here.Cut along dotted line.Action Remote commandPlay all messages ..................1Play new messages...............2Delete the message..............3Delete all old messages .....33Repeat or go back.................4Stop...............................................5Help menu .................................*5Skip the message...................6Record announcement ........*7Turn system off or on ..........0End remote access call ......8(or hang up)Call your phone number, then enter your two-digit access code (preset to 19).EL421085.8 GHz cordless telephone/answering system© 2007 Advanced American Telephones. All rights reserved.AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,licensed to Advanced American Telephones. Printed in China.
www.telephones.att.com© 2007 Advanced American Telephones. All rights reserved.AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,licensed to Advanced American Telephones. Printed in China. Issue 1 AT&T 09/07.91-001523-010-100

Navigation menu