VTech Telecommunications 80-6684-01 1.9GHz CORDLESS PHONE User Manual 5
VTech Telecommunications Ltd 1.9GHz CORDLESS PHONE Users Manual 5
Contents
Users Manual 5
Getting started Installation options 4. Plug the telephone line cord into a telephone wall jack, and plug the power adapter cord into a power outlet not controlled by a wall switch. Place the cords in the bracket channels. Telephone line cord Power adapter DSL filter (not included), required if you have DSL high-speed Internet service. 13 Getting started Expansion handset and cordless headset Your new AT&T TL92278/TL92378/TL92328���������������������� ��������������������������������������������� telephone system can accommodate up to 12 devices (AT&T TL90078 expansion handset and/or AT&T TL7600 cordless headset). You can add new handsets (AT&T TL90078 purchased separately) or cordless headset (AT&T TL7600 purchased ���������� separately�������������������������������������������������������������� ) to your telephone system but each device must be registered with the telephone base before use. A maximum of two cordless headsets can be registered with the telephone base. To register a new handset, see page XX. The handsets provided with the TL92278 come pre-registered as HANDSET 1 and HANDSET 2. You can register additional devices from either of the following combinations, 1) ten additional handsets, 2) nine additional handsets and one cordless headset, or 3) eight additional handsets and two cordless headsets. Additional handsets will be assigned numbers in the order they are registered (HANDSET 3, HANDSET 4, HANDSET 5 and so on); additional headsets will be assigned numbers in the order they are registered (HEADSET 1 with blue indicator light; HEADSET 2 with orange indicator light.) The handsets provided with the TL92378/TL92328 come pre-registered as HANDSET 1, HANDSET 2 and HANDSET 3. You can register from either of the following combinations, 1) nine additional handsets, 2) eight additional handsets and one cordless headset, or 3) seven additional handsets and two cordless headsets. Additional handsets will be assigned numbers in the order they are registered (HANDSET 4, HANDSET 5, HANDSET 6 and so on); additional headsets will be assigned numbers in the order they are registered (HEADSET 1 with blue indicator light; HEADSET 2 with orange indicator light.) 14 Getting started Adding and registering handsets (optional) NOT REGISTERED PRESS HNDST LOC Handsets purchased (AT&T TL90078) separately need to be registered to the telephone base before use. When first purchased, all expansion handsets will show NOT REGISTERED on the screen. The new handset(s) may need to be charged for five minutes before registering to the telephone base. To register a handset to your telephone base 4 SEC ON BASE 1. Place the unregistered handset into the telephone base. If PRESS HNDST LOC 4 SEC ON BASE does not appear on the handset screen after a few seconds, remove the handset and place it in the telephone base again. 2. On the telephone base, press and hold HANDSET LOCATOR for about four seconds (until the red IN USE light on the telephone base turns on) and then release the button. The handset will show PLEASE WAIT... and it will take about 10 seconds to complete the registration. The handset will show HS X REGISTERED and will beep if the registration is successful. PLEASE WAIT... NOTES: 1. If the registration is not successful, the display will show NOT REGISTERED. To reset the handset, remove the handset from the telephone base and place it back in. Try the registration process again. HS X REGISTERED 2. You cannot register a handset if any other system handset is in use. 15 Getting started Replacing a handset You may need to de-register your handsets if: You have twelve registered handsets and need to replace a new unit. -ORYou wish to change the designated handset number of your registered handsets. You must first de-register ALL the handsets, and then re-register each handset you wish to use. Please read carefully through all the instructions on this page before beginning the de-registration process. To de-register all handsets 1. Press and hold HANDSET LOCATOR on the telephone base for about 10 seconds (until the IN USE light turns on and starts to flash), then release the HANDSET LOCATOR button. 2. Immediately press and release HANDSET LOCATOR again. You must press HANDSET LOCATOR while the IN USE light is still flashing. (The light flashes for about seven seconds. If the light stops flashing, pick up the handset and place it back into the telephone base, then start again with step one above.) 3. The handset(s) will show CONNECTING... and it will take about 10 seconds to complete the de-registration process. ALL handsets will show NOT REGISTERED if de-registration was successful. 4. To re-register the handset(s) to the telephone base, follow the registration instructions on pages 14-15. NOTES: 1. If the de-registration process was not successful, you may need to reset the system and try again. To reset: pick up the handset and press the HOME/FLASH button, then press the OFF/CLEAR button and place the handset back into the telephone base. You may also reset by unplugging the power from the telephone base and plugging it back in. 2. You cannot de-register the handset(s) if any other system handset is in use. 3. You will need to reset the system clock after de-registering handset(s), refer to pages 42-43 for details. 16 Bluetooth Introducing Bluetooth Your new AT&T TL92278/TL92378/TL92328 �������������������������������������������������������� �������������������������������� telephone system with Bluetooth wireless technology has the following features: •�������������������������������������������������������������� Pair a Bluetooth enabled cell phone with the telephone base. •������������������������������������������ Connect a cell phone to make and receive CELLULAR calls. Only one cell phone can be paired and connected on a call at a time. •���������������������������������������������������������������������������� Make and receive calls using your cell phone plan while utilizing the ease and comfort of your home telephone system. IMPORTANT INFORMATION •....................................................................... Refer to your cell phone user's manual for more information about its Bluetooth function. • Operate your Bluetooth device within 12 feet from the telephone base. Bluetooth technology operates best within a short range. Keeping within 12 feet will ����������������������������������������������������������������� maintain the connection quality of the Bluetooth device with the telephone base. •............................................................................ Make sure that your cellular phone has sufficient signal strength. You may need to move the cellular phone and telephone base to a location where the cellular signal strength may be stronger. •......................................................................... Charge your Bluetooth cell phone while it is connected to the telephone base because your cell phone's battery will discharge faster while it is connected wirelessly to the telephone base. •....................................................................... Monitor your cell phone's usage because airtime is deducted from your cellular plan for the duration of CELLULAR calls. Refer to the Bluetooth Setup section (page 22) to learn how to set up your Bluetooth device. Refer to the Telephone operation section (page 55) on how to operate your Bluetooth devices with your new AT&T telephone system with Bluetooth wireless technology. Refer to the Troubleshooting section (page 94) if you experience difficulty using the telephone system. 17 Bluetooth Glossary of terms Below are some terms used in this user’s manual to help you become familiar with using your Bluetooth devices and your new AT&T telephone system. Bluetooth cell phone - Refers to a mobile Bluetooth enabled cellular telephone. CELLULAR line - The communications service provided through your Bluetooth enabled cellular telephone. HOME line - ��������������������������������������� Your conventional telephone land line.� Connected - A Bluetooth device can only be used when it is connected to the telephone base. Paired Devices - Once a Bluetooth device has been paired with the telephone base, it will be stored in the telephone base. Only one Bluetooth cellular phone can be paired with the telephone base. Pairing - This refers to the process of Bluetooth device registering device information with each other. The telephone base must be paired with a Bluetooth cellular phone before the Bluetooth device can be used. Depending on the manufacturer, this is also referred to as Bonding. PIN - By default, the PIN is 0000 for the telephone base and for most Bluetooth devices. PIN information must be exchanged between Bluetooth devices before they can be used. This is also known as a Passkey or Passcode. 18 Bluetooth Bluetooth Setup To use a Bluetooth enabled cellular phone with you telephone, you must first pair and connect your Bluetooth cellular phone with the telephone base. Before you begin, make sure that your Bluetoothenabled cellular phone is not connected to any other Bluetooth device. Refer to your cellular phone's user's manual to learn how to search for or add new Bluetooth devices. To pair and connect a cellular phone: 1. Press and hold the BLUETOOTH button on the telephone base until it is flashing. The Bluetooth feature will be activated. 2. Using your cellular phone, turn on the Bluetooth feature and search for a new device. 3. Once your cellular phone has found the AT&T DECT 6.0 telephone base, select it. 4. Using your cellular phone, enter the PIN of the telephone base (the default PIN is 0000) to continue the pairing process. HANDSET 1 When a device is successfully connected, the status icon will display on the handset screen display, and the light of the BLUETOOTH button on the telephone base will be on steadily. Once your have paired a device with the telephone base, the pairing information will be stored in the telephone base. However, if the paired device becomes disconnected, the telephone base will not automatically search and re-connect to that device. To re-connect a paired device, start again with step one above. If you want to pair and connect a new device when there is already a connected device on the telephone base, press and hold the BLUETOOTH button on the telephone base until it is flashing, then start with step two above. If you do not pair a new device within two minutes, the BLUETOOTH light on the telephone base will be turned off and the system will return to idle. 19 Getting started Handset main menu To enter the main menu: 1.������� Press MENU/SELECT when the handset is in idle mode. 2. Press DIR / CID to select a handset feature menu, then press MENU/SELECT to enter that menu. To return to the idle mode, press and hold DIRECTORY allows you to store and search for names and numbers (page 21). >DIRECTORY CALL LOG RINGER VOLUME allows you to set the ringer volume (page 12). >RINGER VOLUME RINGER TONE LANGUAGE allows you to set your handset display language (page 11). >LANGUAGE CLR VOICE MAIL OFF/CLEAR. CALL LOG allows you to view caller ID history (page 21). >CALL LOG INTERCOM RINGER TONE allows you to set the ringer for the HOME and CELLULAR lines (page XX). >RINGER TONE KEY TONE CLR VOICE MAIL allows you to turn off the new voicemail indication. >CLR VOICE MAIL HOME AREA CODE 20 INTERCOM allows you to intercom with other handset. >INTERCOM RINGER VOLUME KEY TONE allows you to turn the keypad tones on or off. >KEY TONE LANGUAGE HOME AREA CODE allows you to set your home area code (page 13). >HOME AREA CODE DIRECTORY Handset settings Handset settings Using the feature menu, you can customize many of the telephone’s settings. >DIRECTORY CALL LOG 1. Press MENU/SELECT when in idle mode (when the phone is not in use) to enter the feature menu. 2. Use DIR / CID to scroll to the feature to be changed. When scrolling through the menu, the top menu item is always highlighted with a > symbol. 3. Press item. MENU/SELECT to select the highlighted NOTE: Press OFF/CLEAR to cancel an operation, back up to the previous menu or exit the menu display. Press and hold OFF/CLEAR to return to idle mode. Ringer volume Using this menu, you can set the ringer volume level (1-6), or turn the ringer off. When the ringer is turned off, will appear on the handset screen. The volume setting will apply to both HOME and CELLULAR calls. >DIRECTORY CALL LOG >RINGER VOLUME RINGER TONE To adjust the RINGER VOLUME: 1. Press MENU/SELECT when in idle mode to enter the feature menu. 2. Use DIR / CID to scroll to >RINGER VOLUME, then press MENU/SELECT. DIR / 3. Press level. RINGER VOLUME CID to sample each volume 4. Press MENU/SELECT to save your preference and return to the feature menu. NOTE: The ringer volume also determines the ringer volume of intercom calls (pages 27-28) and the paging tone for the handset locator feature (page 23). If the handset ringer volume is set to off, that handset is silenced for all incoming calls and paging. 21 Handset settings Handset settings Ringer tone >DIRECTORY CALL LOG You can select different ringer tones for the HOME and CELLULAR calls. You may choose one of 10 ringer tones. To choose a ringer tone for the HOME line: >RINGER TONE KEY TONE >HOME 1. Press MENU/SELECT when in idle mode to enter the feature menu. 2. Use DIR / CID to scroll to >RINGER TONE, then press MENU/SELECT. TONE CELLULAR TONE 3. Press MENU/SELECT to select HOME TONE. 4. Press DIR / CID to get to the next ringer tone and to hear a sample of it. RINGER TONE 5. Press MENU/SELECT to save your preference and return to the feature menu. To choose a ringer tone for the CELLULAR line: >DIRECTORY CALL LOG 1. Press MENU/SELECT when in idle mode to enter the feature menu. 2. Use DIR / CID to scroll to >RINGER TONE, then press MENU/SELECT. >RINGER TONE KEY TONE 3. Press DIR / CID to scroll to CELLULAR TONE, then press MENU/SELECT. 4. Press DIR / CID to get to the next ringer tone and to hear a sample of it. >CELLULAR TONE HOME TONE 5. Press MENU/SELECT to save your preference and return to the feature menu. RINGER TONE 22 Handset settings Handset settings Key tone >DIRECTORY CALL LOG The handset is factory programmed to beep with each key press. If you turn off the KEY TONE, there will be no beeps when keys are pressed. To turn the KEY TONE on or off: >KEY TONE LANGUAGE KEY TONE ON 1. Press MENU/SELECT when in idle mode to enter the feature menu. 2. Use DIR / CID to scroll to >KEY TONE, then press MENU/SELECT. DIR / 3. Press CID to select ON or OFF. 4. Press MENU/SELECT to save your preference and return to the feature menu. Language >DIRECTORY CALL LOG >LANGUAGE CLR VOICE MAIL LANGUAGE ENGLISH In this menu, you can select the language used for all screen displays. To select a language: 1. Press MENU/SELECT when in idle mode to enter the feature menu. 2. Use DIR / CID to scroll to >LANGUAGE, then press MENU/SELECT. 3. Press DIR / CID to select ENGLISH, FRANCAIS or ESPANOL. 4. Press MENU/SELECT to save your preference and return to the feature menu. 23 Handset settings Handset settings Visual message waiting (voicemail) indicator If you subscribe to a voicemail service offered by your local telephone company, the voicemail waiting indicator feature will provide visual indication when you have new voicemail messages. The VOICEMAIL light on the telephone base will flash, and NEW VOICE MAIL and the icon will appear on the handset screen(s). NOTES: 1. This feature does not indicate new answering system messages recorded on your phone. 2. For more information about the difference between your answering system and voicemail, see page 41. To clear voice mail indication >DIRECTORY CALL LOG >CLR VOICE MAIL HOME AREA CODE TURN OFF INDICATOR? NOTES: 1. Telephone company voicemail may alert you to new messages with stutter (broken) dial tone. Contact your telephone company for more details. 2. For information about using your voicemail service contact your telephone company for assistance. Use this feature when the telephone indicates there is new voicemail but there is none (for example, when you have accessed your voicemail from a different telephone line while away from home). This feature only turns off the displayed NEW VOICE MAIL message, icon and VOICEMAIL light; it does not delete your voicemail message(s). If there actually are new voicemail messages, your local telephone company will continue to send the signal to activate the visual message waiting indicator. To manually turn off the new voicemail indicator: 1. Press MENU/SELECT when in idle mode to enter the feature menu. 2. Use DIR / CID to scroll to >CLR VOICE MAIL, then press MENU/SELECT. 3. Press MENU/SELECT again to turn the voicemail indication off, or press OFF/CLEAR to cancel the procedure. 24 Handset settings Handset settings Home area code If you dial seven digits to make a local call (no area code required), program your area code into the telephone as the home area code. After setting, if you receive a call from within your home area code, the screen will display the seven digits of the telephone number. >DIRECTORY CALL LOG >HOME AREA CODE DIRECTORY 1. Press MENU/SELECT in the idle mode to enter the handset main menu. 2. Use DIR / CID to scroll to >HOME AREA CODE, then press MENU/SELECT. HOME AREA CODE --- 3. Press the dial pad keys to enter a three-digit home area code. Press DELETE/MUTE to delete digit while entering. 4. Press MENU/SELECT to save and return to the main menu. NOTE: If, in the future, your telephone service provider requires you to dial 10 digits to make a local call (area code + phone number), press DELETE/MUTE to delete all digits in the home area code setting menu, that will restore the home area code to its default setting as ---. Temporary ringer silencing DELETE/MUTE OFF/CLEAR Press OFF/CLEAR or DELETE/MUTE while the telephone is ringing to silence the ringer temporarily. This will silence the ringer without disconnecting the call. The next incoming call will ring normally at the preset volume. NOTE: Each handset will ring when there is an incoming call unless the ringer volume is turned off. Pressing OFF/CLEAR or DELETE/MUTE on one handset will only silence the ringer of that particular handset. 25 Telephone operation Handset operation Elapsed time HOME 00:00:30 Making a HOME call To make a HOME call: • Press HOME/FLASH or SPEAKER, then enter the telephone number. -OR• Enter the telephone number, then press HOME/FLASH or SPEAKER. Press DELETE/MUTE or OFF/CLEAR to make corrections when entering the phone number. To end a HOME call: NOTE: Pressing HOME/FLASH to access services from your local telephone service provider will not affect the elapsed time. • Press OFF/CLEAR or return the handset to the telephone base or charger. Answering a HOME call To answer a HOME call: • Press HOME/FLASH or SPEAKER. –OR– • Press any dial pad key (0-9, * or #). To end a HOME call: • Press OFF/CLEAR or return the handset to the telephone base or charger. Call waiting on the HOME line If you subscribe to call waiting service with your local telephone service provider, you will hear a beep if someone calls while you are already on a call. Press HOME/FLASH to put your current call on hold and take the new call. You can press HOME/FLASH at any time to switch back and forth between calls. 26 Telephone operation Handset operation Receive a CELLULAR call while on a HOME call While on a HOME call and there is an incoming CELLULAR call, CELLULAR on the handset will flash and you will hear a short beep. To answer the incoming CELLULAR call: • Press CELLULAR on the handset. The HOME call will automatically be placed on hold and HOME/FLASH will start flashing. To end the CELLULAR call: • Press OFF/CANCEL on the handset. The HOME line will still be on hold. HOME LINE HELD will appear on the screen display. To resume the HOME call already on hold: • Press HOME/FLASH on the handset. NOTE: If you have voice mail service active on your cellular phone, and you do not answer the incoming CELLULAR call, the call will be answered by your cellular phone's voice mail. Contact your cellular service provider for more information about voice mail service. 27 Telephone operation Handset operation Making a CELLULAR call Elapsed time CELL 00:00:30 To make a CELLULAR call: • Enter the telephone number (pre-dial mode), then press CELLULAR. Press DELETE/MUTE or OFF/CLEAR to make corrections when entering the phone number. To end a CELLULAR call: • Press OFF/CLEAR or return the handset to the telephone base or charger. The screen displays the elapsed time as you talk (in hours, minutes and seconds). Answering a CELLULAR call To answer a CELLULAR call: To answer a CELLULAR call: • Press CELLULAR or SPEAKER. To end a CELLULAR call: • Press OFF/CLEAR or return the handset to the telephone base or charger. Call waiting on the CELLULAR line If you subscribe to call waiting service provided by your cellular service provider, you will hear one or more beeps if you have an incoming CELLULAR call while already on a call. Press CELLULAR to put your current call on hold and take the new call. You can press CELLULAR at any time to switch back and forth between calls. 28 Telephone operation Handset operation Receive a HOME call while on a CELLULAR call While on a CELLULAR call and there is an incoming HOME call, HOME/FLASH will flash on the handset and you will hear a short beep. To answer the incoming HOME call: • Press HOME/FLASH on the handset. The CELLULAR line call will automatically be placed on hold and CELLULAR will start flashing. To end the HOME call: • Press OFF/CANCEL on the handset. The CELLULAR line will still be on hold. CELL LINE HELD will appear on the display. To resume the CELLULAR call on hold: • Press CELLULAR on the handset. NOTE: If the answering system is on and you do not answer an incoming HOME call while on the CELLULAR line, the incoming HOME line call will be answered by the answering system. 29 Telephone operation Handset operation Elapsed time HOME 00:00:30 Handset speakerphone During a call, you can press SPEAKER to alternate between hands-free speakerphone and normal handset use. Press OFF/CLEAR to hang up. NOTE: Speakerphone will be disable if the handset is in low battery mode. However, if the handset enters low battery mode while you are using the speakerphone, the call will remain in speakerphone mode until you hang up. REDIAL 888-883-2445 Last number redial To view the five most recently dialed numbers: • Press REDIAL/PAUSE to display the most recently called number (up to 30 digits). • Press DIR / CID or REDIAL/PAUSE repeatedly to view up to five recently called numbers. The handset will beep twice at the beginning and at the end of the list. Press OFF/CLEAR to exit. To redial a number: • Press HOME/FLASH or SPEAKER to dial the displayed number from the HOME line. -OR• Press CELLULAR to dial the displayed number from the CELLULAR line. -OR• Press HOME/FLASH or SPEAKER, then REDIAL/PAUSE to call the most recently called number (up to 30 digits). While reviewing the redial memory, press DELETE/MUTE to delete the displayed number. 30 Telephone operation Handset operation Handset locator The handset locator feature is useful if you misplace a handset(s). To start the paging tone: • Press HANDSET LOCATOR at the telephone base. This starts the paging tone on the handset(s) for 60 seconds. NOTE: When paging, if you press OFF/CLEAR or DELETE/MUTE on a handset, the ringer of the handset will be silent but the handset locator feature will not be cancelled. To stop the paging tone: **PAGING** • Press HOME/FLASH, SPEAKER, or any dial pad key (0-9, *, or #) on the handset(s), –OR– • Press HANDSET LOCATOR on the telephone base. NOTE: The handset ringer volume also determines the level of the paging tone. If the handset ringer volume level is set to off, that handset will be silent for all calls and paging (page 16). 31 Telephone operation Options while on calls Volume control To adjust the listening volume on a handset: Press DIR / CID ������������������������ to adjust the listening volume when on a call. Each press of the button increases or decreases the volume level. NOTES: 1. All volume settings (normal handset and speakerphone) are independent. 2. When the volume reaches the minimum or maximum setting, you will hear two beeps. Multiple handset use (conference call) You can conference with another system handset while you are either on a HOME or CELLULAR call. However, you cannot conference between a HOME call and CELLULAR call. If a handset is already on a call and you would like to join the call, press HOME/FLASH or SPEAKER on another system handset. A maximun of four handsets can be used on a call. Press OFF/CLEAR or place the handset in the telephone base or charger to end the call. The call will not be terminated until all handsets hang up. NOTE: Only two system handsets can be used at the same time on an outside call. 32 Telephone operation Options while on calls Mute DELETE/MUTE The mute function allows you to turn off the microphone. You can hear the caller, but the caller will not be able to hear you. To mute a call: • Press DELETE/MUTE to turn off the microphone. When mute is on, the handset screen will show MUTED for a few seconds and the MUTE icon will be shown until mute is turned off. To un-mute a call: • Press DELETE/MUTE again and resume speaking. When mute is turned off, MICROPHONE ON will display temporarily on the handset screen. NOTE: You cannot press OFF/CLEAR to exit redial, directory or caller ID history without ending the call. 33 Telephone operation Options while on calls Hold HOME LINE HELD You can place a HOME or CELLULAR call on hold, if the call is not retrieved in one minute, it will be disconnected. To place a HOME call on hold: CELL LINE HELD • Press the HOLD key on the handset. HOME LINE HELD will appear on the display and the HOME/FLASH will flash. Press the HOLD key again to resume the HOME call. To place a CELLULAR call on hold: • Press the HOLD key on the handset. CELL LINE HELD will appear on the display and the CELLULAR will also flash. Press the HOLD key again to resume the CELLULAR call. 34 Telephone operation Chain dialing NOTES: 1. You cannot edit a directory entry while you are on a call. For more details about the directory, see page 34. 2. You cannot copy a caller ID entry into the directory while you are on a call. For more details about the caller ID history, see page 40. 3. While on a call, only the most recently called number can be reviewed, and erasing the entry is not allowed. For more details about the redial memory, see page 22. This feature allows you to initiate a dialing sequence from numbers stored in the directory, caller ID history or redial list while you are on a call. Chain dialing can be useful if you wish to access numbers other than phone numbers (such as bank account information or access codes) from the directory, caller ID history or redial list. Directory 1. Press MENU/SELECT twice. 2. Press number. DIR / CID to scroll to the desired 3. Press MENU/SELECT to dial the displayed number. Caller ID history (call log) 1. Press MENU/SELECT. 2. Press LOG. DIR / CID to scroll to >CALL 3. Press number. DIR / CID to scroll to the desired 4. Press MENU/SELECT to dial the displayed number. Last number redial Press REDIAL/PAUSE to display and dial the most recently dialed number. If you press REDIAL/PAUSE again within two seconds, the number will not be dialed. 35 Telephone operation Intercom Use the intercom feature for conversations between handsets. You can buy additional accessory handsets (model AT&T TL90078) for this telephone base. Up to 12 handsets can be registered to the telephone base. The first nine handsets that you register will be named Handsets 1-9. Use the handset number to intercom and transfer calls. Although the names for handsets 10-12 will appear in their displays as 10-12, when you intercom or transfer to one of them, you must use *0 for Handset 10, *1 for handset 11, and *2 for Handset 12. NOTES: 1. Before the intercom call is answered, you can cancel the intercom call by pressing OFF/CLEAR on the calling handset. 2. If the called handset is not answered within 100 seconds, or if it is in the directory or caller ID history mode, or on a call, or out of range, the calling handset will show the message UNABLE TO CALL TRY AGAIN. 3. Pressing OFF/CLEAR or DELETE/MUTE will temporarily silence the intercom ringer. Model TL92278 (without additional handset registered) 1. Press MENU/SELECT when in idle mode to enter the feature menu. 2. Use DIR / CID to scroll to >INTERCOM, then press MENU/SELECT. 3. The screen will show CALLING OTHER HANDSET. The called handset will ring, and its screen will show OTHER HANDSET IS CALLING. 4. On the ringing handset, press HOME/FLASH, INT, SPEAKER, or any dial pad key (0-9, * or #) to answer the intercom call. To end the intercom call: • Press OFF/CLEAR on either handset. -OR• Place either handset in the charger or telephone base. 36 Telephone operation Intercom NOTES: 1. Before the intercom call is answered, you can cancel the intercom call by pressing OFF/CLEAR on the calling handset. 2. If the called handset is not answered within 100 seconds, or if it is in the directory or caller ID history mode, or on a call, or out of range, the calling handset will show the message UNABLE TO CALL TRY AGAIN. 3. Pressing OFF/CLEAR or DELETE/MUTE will temporarily silence the intercom ringer. Model TL92278 (with additional handset registered)/TL92378/TL92328 1. Press MENU/SELECT when in idle mode to enter the feature menu. 2. Use DIR / CID to scroll to >INTERCOM, then press MENU/SELECT. The screen will show INTERCOM TO:. 3. Enter the handset number 1-9 or, for handsets 10, 11 and 12, enter *0, *1 or *2, respectively. The display will show CALLING HANDSET X, with X being the handset number. The called handset will ring, and its screen will show HANDSET X IS CALLING. 4. On the ringing handset, press HOME/FLASH, INT, SPEAKER, or any dial pad key (0-9, * or #) to answer the intercom call. To end the intercom call: • Press OFF/CLEAR on either handset. -OR• Place either handset in the charger or telephone base. 37 Telephone operation Call transfer using intercom Use the intercom feature to transfer an outside call to another system handset. Model TL92218 (without additional handset registered) 1. When on an outside call, press MENU/SELECT when in idle mode to enter the feature menu. 2. Use DIR / CID to scroll to >TRANSFER, then press MENU/SELECT. The outside call is automatically placed on hold. The transferring handset’s screen will show CALLING OTHER HANDSET. The called handset will ring, and its screen will show OTHER HANDSET IS CALLING. NOTES: 1. Before the intercom call is answered, you can cancel the transfer and return to the outside call by pressing OFF/CLEAR or HOME/FLASH. 2. If the called handset does not answer the intercom call within 100 seconds, is in directory or caller ID history mode or is or out of range, the transferring handset will show UNABLE TO CALL TRY AGAIN on its screen and will automatically return to the outside call. 3. You can end the intercom call and return to the outside call by pressing HOME/FLASH or CELLULAR key (depending on which call is being transferred) on the originating handset, or pressing OFF/CLEAR on the destination handset. 2. On the ringing handset, press HOME/FLASH, INT, SPEAKER, or any dial pad key (0-9, * or #) to answer the intercom call. You can now talk without the outside caller hearing the conversation. 3. Press OFF/CLEAR on the transferring handset or place it in the telephone base or handset charger to complete the transfer. The transferring handset’s screen will show CALL TRANSFERED and the other handset will automatically be connected to the outside call. -ORPress the HOME/FLASH or CELLULAR key (depending on which call is being transferred) on the called handset to let both parties conference with the external line. 38 Telephone operation Call transfer using intercom NOTES: 1. Before the intercom call is answered, you can cancel the transfer and return to the outside call by pressing OFF/CLEAR or HOME/FLASH. 2. If the called handset does not answer the intercom call within 100 seconds, is in directory or caller ID history mode or is or out of range, the transferring handset will show UNABLE TO CALL TRY AGAIN on its screen and will automatically return to the outside call. 3. You can end the intercom call and return to the outside call by pressing HOME/FLASH or CELLULAR key (depending on which call is being transferred) on the originating handset, or pressing OFF/CLEAR on the destination handset. Model TL92278 (with additional handset registered)/ TL92378/TL92328 1. When on an outside call, press MENU/SELECT when in idle mode to enter the feature menu. 2. Use DIR / CID to scroll to >TRANSFER, then press MENU/SELECT. The screen will show INTERCOM TO:. 3. Enter the handset number 1-9 or, for handsets 10, 11 and 12, enter *0, *1 or *2, respectively. The display will show CALLING HANDSET X, with X being the handset number. The called handset will ring, and its screen will show HANDSET X IS CALLING. 4. On the ringing handset, press HOME/FLASH, INT, SPEAKER, or any dial pad key (0-9, * or #) to answer the intercom call. You can now talk without the outside caller hearing the conversation. 5. Press OFF/CLEAR on the transferring handset or place it in the telephone base or handset charger to complete the transfer. The transferring handset’s screen will show CALL TRANSFERED and the other handset will automatically be connected to the outside call. -ORPress the HOME/FLASH or CELLULAR key (depending on which call is being transferred) on the destination handset to let both parties conference with the external line. 39 Directory About the directory Shared directory Robert Brown 888-883-2445 The directory is stored in the telephone base, and is shared by all handsets. Changes made to the directory on any one handset will apply to all. NOTE: Only one handset can review the directory at a time. If another handset attempts to enter the directory, the screen will display NOT AVAILABLE AT THIS TIME. Capacity The directory can store up to 50 entries, with a maximum of 15 alphanumeric characters (including spaces) for the names and 30 digits for the telephone numbers. A convenient search feature can help you find and dial numbers quickly (page 35). If there are already 50 entries, the screen will display LIST FULL. You will not be able to store a new number until an existing one is deleted. Exiting the directory Press OFF/CLEAR to cancel an operation, back up to the previous menu, or exit the menu display. Press and hold OFF/CLEAR to return to the idle mode. If you pause for too long while creating or reviewing an entry, the procedure will time out and you will have to begin again. 40 Directory Creating directory entries To create a new directory entry 1. Press MENU/SELECT when in idle mode to enter the feature menu. >DIRECTORY CALL LOG 2. Press MENU/SELECT again to enter >DIRECTORY menu. CID to highlight STORE. 3. Press >REVIEW STORE 4. Press MENU/SELECT. 5. Enter the telephone number when prompted. • Use the dial pad to enter up to 30 digits. >STORE REVIEW ENTER NUMBER 888-883-2445_ – Press DIR / CID to move the cursor to the right or left. – Press DELETE/MUTE to erase digits. – Press and hold DELETE/MUTE to erase all digits. – Press and hold REDIAL/PAUSE to enter a three-second dialing pause. -OR• Copy a number from redial by pressing REDIAL/PAUSE then press DIR or to locate the number to copy. Press MENU/SELECT to copy the number. CID 6. Press MENU/SELECT to save the number in the display. The display will show ALREADY SAVED if the number is already in the directory. The same number cannot be saved twice. 41 Directory Creating directory entries 7. Enter the name when prompted. ENTER NAME Robert Brown_ NOTE: The first letter of every word will be capitalized. The remaining letters in a word begin with lower case letters shown in the chart to the right. Robert Brown 888-883-2445 • Use the dial pad to enter a name (up to 15 characters). Each time a key is pressed, the character on that key will be displayed. Additional key presses will produce other characters on that key. See the chart below. – ������ �������� Press DIR or CID to move the cursor to the right or left. – Press DELETE/MUTE to erase letters. – Press and hold DELETE/MUTE to erase all letters. Dial Key # space Characters by number of key presses ‘ 8. Press MENU/SELECT to store your new directory entry. The name and the telephone number will then be shown on the screen. To change them later, see page 36. 42 Directory Directory review To review directory entries DIR 1. Press DIR when in idle mode to display the first entry in the directory. DIRECTORY EMPTY will be displayed if there are no directory entries. -ORYou can also display the first entry in the directory by pressing MENU/SELECT twice, then pressing MENU/SELECT again to choose >REVIEW. 2. Press DIR or CID to browse through the directory. Entries will be displayed alphabetically by the first letter in the name. 43 Directory Directory search To search by name DIR 1. Press DIR when in idle mode to display the first listing in the directory. DIRECTORY EMPTY will be displayed if there are no directory entries. 2. When a name entry is displayed, press the dial pad keys (2-9) to start a name search. The directory will display the first name beginning with the first letter associated with the dial pad key if there is an entry in the directory that begins with that letter. 3. To see other names that start with the letters on the same dial pad key, keep pressing the key. The names will be shown in alphabetical order. For example, if you have the names Jennifer, Jessie, Kevin and Linda in your directory: • If you press 5 (JKL) once, you will see Jennifer. • If you press 5 (JKL) twice, you will see Jessie. • If you press 5 (JKL) three times, you will see Kevin. • If you press 5 (JKL) four times, you will see Linda. • If you press 5 (JKL) five times, you will see Jennifer again. NOTES: 1. If there is no name matching the first letter of the key you press, you will see a name that matches the second letter of the key. 2. If you press a key (2-9) and no name starts with the letters on that key, the directory will show the entry that matches the next letter in the directory. 44 Directory To dial, delete or edit entries To dial, delete or edit a directory entry (name and number), the entry must be displayed on the handset. Use the directory search or review (pages 34-35) to display an entry. Display dial To dial a displayed number from the directory, press HOME/FLASH or SPEAKER to dial from the HOME line; or press CELLULAR to dial from the CELLULAR line. To delete an entry When a directory entry is displayed, press DELETE/MUTE to delete the displayed entry from the directory. Once deleted, an entry cannot be retrieved. To edit an entry When a directory entry is displayed: 1. Press MENU/SELECT to modify the entry. You will be prompted to EDIT NUMBER. Andrew 888-490-2005 • Press the dial pad keys to add digits. • Press DELETE/MUTE to erase digits. DIR or • Press EDIT NUMBER 888-883-2445 EDIT NAME Andy Andy 888-883-2445 CID to move the cursor. • Press and hold REDIAL/PAUSE to add a threesecond pause if desired. • Press REDIAL/PAUSE, then DIR or CID to scroll to a previously dialed number. Press MENU/SELECT to add the redial number to the entry. 2. Press MENU/SELECT. ������������������������� You will be prompted to EDIT NAME. • Press the dial pad keys to add characters (page 33). • Press DELETE/MUTE to erase characters. DIR or • Press 3. Press MENU/SELECT 45 CID to move the cursor. to confirm. Caller ID Caller ID operation CHRISTINE SMITH 888-722-7702 NEW AM 10:01 11/23 This product supports caller ID services provided by most local telephone service companies. Depending on your service subscription, you may see the caller’s number, or the caller’s name and number which are sent by the telephone company after the first or second ring. Caller ID allows you to see the name, number, date and time of the incoming callers on the HOME and CELLULAR lines. Caller ID with call waiting lets you see the name and telephone number of the caller before answering the telephone, even when on another call. In addition, the time and date are sent by the telephone and cellular service provider along with the caller ID information. These services are available only if both you and the caller are in areas offering caller ID service, and if both telephone companies use compatible equipment. Contact your local telephone company and cellular service provider if: NOTE: You can use this product with regular caller ID service, or you can use this product’s other features without subscribing to either caller ID or combined caller ID with call waiting service. • You have both caller ID and call waiting, but as separate services (you may need to combine these services). • You have only caller ID service, or only call waiting service. • You don’t subscribe to any caller ID or call waiting services. You can use this product with regular caller ID service, or you can use this product’s other features without subscribing to either caller ID or combined caller ID with call waiting service. 46 Caller ID Caller ID operation Caller ID history information CHRISTINE SMITH 888-722-7702 10:01 AM NEW 11/23 If you subscribe to caller ID services, provided by your local telephone company and/or cellular service provider, ����������������������������� The caller ID history stores information about the last 50 incoming calls ���� for both the HOME and CELLULAR lines. Although the call log records the caller ID information of both lines, CELLULAR line call log entries only provide the incoming telephone number. The time and date of the call will appear in the call log entry if only the time is set. The Bluetooth name of the cellular phone will also appear. However, if the number on the incoming CELLULAR call matches a number in the directory, the name will be retrieved from the matched directory entry. Review the caller ID history to find out who called, to easily return the call, or to copy the caller’s name and number into your directory. The phone deletes the earliest entry when the log is full to make room for new calls. If you answer a call before the information appears on the screen, it will not be saved in the caller ID history. The caller ID history is stored in the telephone base, and is shared by all handsets. Changes made on any one handset will be reflected in all. NOTE: Only one handset can review the caller ID history at a time. If another handset attempts to enter the directory or caller ID history, it will display NOT AVAILABLE AT THIS TIME. Caller’s name Incoming HOME call CHRISTINE SMITH 888-722-7702 NEW AM 10:01 Time of call 47 11/23 Caller’s number Appears when the call is missed and un-reviewed Incoming CELLULAR call Date of call Caller ID Caller ID operation Chris 888-722-7702 NEW AM 10:01 11/23 Memory match If the incoming telephone number exactly matches a telephone number in your directory, the name that appears on the screen will match the corresponding name in your directory. For example, if Christine Smith calls, her name will appear as Chris if this is how you entered it into your directory. NOTE: The number shown by your caller ID will be in the format sent by the phone company. The phone company usually delivers ten-digit phone numbers (area code plus phone number). If the telephone number of the caller does not exactly match a number in your directory, the name will appear as it is delivered by the phone company. For example if the phone company includes the area code and the directory number does not, the name will appear as delivered by the phone company. There are also occasions when other information or no information is displayed for various resaons: On-screen messsage Reason PRIVATE NUMBER The caller's number has been set as private. PRIVATE NAME The caller's name has been set as private. PRIVATE CALLER Caller's name and telephone number are not revealed at caller's request. UNKNOWN NUMBER Your local telephone company is unable to determine the caller's number. UNKNOWN NAME Your local telephone company is unable to determine the caller's name. UNKNOWN CALLER Your local telephone company is unable to determine the caller's name and telephone number. Calls from other countries may also generate this message. 48 Caller ID Caller ID operation Missed (new) calls indicator HANDSET 1 6 MISSED CALLS Robert Brown 888-883-2445 NEW 10:31 AM 11/23 When a handset is in idle mode and has calls that have not been reviewed, its screen will show XX MISSED CALLS. All entries which have not been reviewed will be counted as missed calls when the phone is idle. Each time an entry in the caller ID history marked NEW is reviewed, the number of missed calls decreases by one. If you have too many missed calls and you do not want to review them one by one, but you still want to keep them in the caller ID history, you can press and hold OFF/CLEAR for four seconds when the handset is idle. All the entries in the caller ID history will be considered old (have been reviewed), and the missed calls counter is reset to 0. 49 Caller ID To review the caller ID history To review the caller ID history 1. Press CID to review the caller ID history in reverse chronological order starting with the most recent call. -ORYou can also review the caller ID history by pressing MENU/SELECT, and using DIR or CID to scroll to >CALL LOG, then press MENU/SELECT. HANDSET 1 6 MISSED CALLS CID 2. Press DIR or CID to scroll through the list as shown on the left. Robert Brown 888-883-2445 NEW 10:31 AM 11/23 To dial from the caller ID history Charlie Johnson 800-222-3111 NEW 10:21 AM 11/23 The various dialing options are: 883-2445 888-883-2445 1-888-883-2445 1-883-2445 883-2445 1-883-2445 888-883-2445 1-888-883-2445 Press # Press 1 While reviewing an entry in the caller ID history: • To dial a displayed number from the caller ID history. Press HOME/FLASH or SPEAKER to dial from the HOME line; or press CELLULAR to dial from the CELLULAR line. -OR• Press # repeatedly to display different dialing options for local and long distance numbers before dialing or saving the telephone number in the directory. See the example on the left. You may also press 1 repeatedly to add or remove a 1 in front of the telephone number before dialing or saving the telephone number in the directory. See the examples on the left. When the number displayed is in the correct format for dialing, following the above step to dial the number. 50 Caller ID To review the caller ID history Other options • Press DELETE/MUTE to delete the displayed entry from the caller ID history. • With an entry from the caller ID history is displayed, press and hold DELETE/MUTE to delete all entries from the caller ID history. When the screen displays DELETE ALL CALLS? press MENU/SELECT to clear the caller ID history of all entries, or press OFF/CLEAR to exit and leave all entries in the caller ID history intact. • Press MENU/SELECT to copy the entry into your directory. You can edit the name and the number (page 36). • Press OFF/CLEAR to exit the caller ID history. NOTES: 1. You may need to change how a caller ID number will be dialed if the entry is not displayed in the correct format. Caller ID numbers may appear with an area code which may not be required for local calls, or without a 1 which may be needed for long distance calls. 2. If neither the name nor number is provided, UNABLE TO SAVE will be displayed. 51 Answering system About the answering system Answering system and voicemail Your telephone has both a digital answering system and voicemail indication. Voicemail is offered by your telephone service provider (fees may apply). Your telephone’s answering system and voicemail indication are independent features, and each alerts you to new messages differently. For more information on the voicemail indicators see page 19. To listen to your voicemail, you typically dial an access number provided by your telephone company, followed by a security code or PIN. To listen to messages recorded on your digital answering system, press PLAY/STOP button on the telephone base. If you subscribe to caller ID/call waiting service through your telephone service provider, you can use your telephone answering system and voicemail together. Set your answering system to answer calls at least two rings earlier than your voicemail is set to answer. For example, set your voicemail to answer calls after six rings and set you answering system to answer after four rings. Some voicemail providers may program the delay before answering calls in seconds instead of rings; in this case allow six seconds per ring when determining the appropriate setting. By doing this, if you are on a call, or if the answering system is busy recording a message and you receive another call, the second caller can leave a voicemail message. 52
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : Yes XMP Toolkit : 3.1-701 Modify Date : 2008:07:02 11:21:08+08:00 Create Date : 2008:07:02 11:21:02+08:00 Metadata Date : 2008:07:02 11:21:08+08:00 Creator Tool : Adobe InDesign CS2 (4.0) Format : application/pdf Document ID : uuid:78078d97-8a59-4c19-a14a-1637957596b5 Instance ID : uuid:88bf79a5-cb10-4316-a405-fe66b04664e7 Producer : Adobe PDF Library 7.0 Page Count : 40 Creator : Adobe InDesign CS2 (4.0)EXIF Metadata provided by EXIF.tools