ValenceTech IBT-03 BLUETOOTH MODULE User Manual iBT 03 Rev0 3 01 FCC
ValenceTech Limited BLUETOOTH MODULE iBT 03 Rev0 3 01 FCC
User Manual
iBT-03 Bluetooth Module for Audio Application iBT-03 Bluetooth Module for Audio Application Doc. Name Date Revision Qualified QDID : B019566 ) iBT-03-Rev0.3.01 2012-07-30 0.3.01 This module is limited to OEM Installation only. Copyright ©, 2012 by Engineering Department, Valence Semiconductor Design Limited. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means without the prior written permission of Valence Semiconductor Design Limited. 0.3.01 1/7 2012-07-30 iBT-03 Bluetooth Module for Audio Application 1. Overview iBT-03 is a Class 2 Bluetooth module supporting Bluetooth V2.1 + EDR specification. It is implemented by using the CSR BlueCore5-Multimedia ROM chip. iBT-03 is designed for receiving audio data transmitting from a mobile device. It can also be used to control the audio playing function of the remote device 2. Features A single chip radio and baseband IC for Bluetooth applications Fully Qualified Bluetooth v2.1+EDR (Enhanced Data Rate) Class 2 power output (10 Meter minimum) Support for 802.11 co-existence High quality 95dB SNR DAC playback LED drivers and faders Supporting profiles : A2DP, AVRCP Build-in PCB antenna Supply voltage : 3.0V to 3.6V RoHS compliant Dimension: 31.0mm (L) x 12mm (W) x 2.6mm (H) 3. Applications Wireless speakers Stereo headset Hands-free car kit VoIP handsets Docking Stations 13 14 15 PIO14 PIO9 PIO4 22 23 24 GND SPI_MISO 25 12 GND RESETB SPI_MOSI 26 MIC_BN 11 SPI_CLK SPI_CSB 27 MIC_BP 10 PIO12 28 3.3V 29 PIO11 PIO13 30 PIO5 SPK_RP PIO3 31 SPK_RN PIO2 32 SPK_LP PIO0 33 SPK_LN PIO1 34 MIC_AN NC 35 MIC_AP GND 36 GND 4. Pin Drawing Figure 1 iBT-03 Pin Diagram 0.3.01 2/7 2012-07-30 iBT-03 Bluetooth Module for Audio Application 5. Pin Description Pin No. Pin Name GND MIC_AP MIC_AN SPK_LN SPK_LP SPK_RN SPK_RP Application Usage GND Pin Type SPK_LN SPK_LP SPK_RN SPK_RP AI AI AO AO AO AO PIO13 STBY / ON 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 3.3V MIC_BP MIC_BN GND PIO14 PIO9 PIO4 GND BT_TX BT_RX AIO1 LED0 LED1 GND RESETB SPI_CLK SPI_MISO SPI_MOSI SPI_CSB PIO12 PIO11 PIO5 PIO3 PIO2 PIO0 PIO1 NC GND MIC_BIAS AIO0 3.3V O4 OD IS 4mA output pad Open drain output pad Input Schmidt Trigger Input Bidirectional AI AI GND REV PAIR AMP_SDB GND LED0 LED1 GND RESETB SPI_CLK SPI_MISO SPI_MOSI SPI_CSB FWD PLAY/PAUSE VOL_DOWN CONNECT VOL_UP O4 O4, PU IS, PD A, B OD4 OD4 IS, PU IS, PD O4, PD IS, PD IS, PU GND A, B Pin Descriptions Ground Microphone A Positive Input Microphone A Negative Input Negative Output of Left Speaker Positive Output of Left Speaker Negative Output of Right Speaker Positive Output of Right Speaker Active High Input for ON / OFF control When iBT-03 is OFF, a high pulse in this pin will turn it ON. When iBT-03 is in ON, a high pulse in this pin will turn in OFF 3.3V Supply Input Microphone B Positive Input Microphone B Negative Input Ground Active High Input for Reverse Control Perform Pair function Active Low signal for shutting down the external Amplifier Ground UART Data Output UART Data Input Analog / Programmable I/O Open Drain LED Driver Output Open Drain LED Driver Output Ground Active Low Module Reset. Must be low for > 5mS Serial Peripheral Interface Clock Serial Peripheral Output Data Serial Peripheral Input Data Active Low Chip Select for Serial Peripheral Interface Active High Input for Forward Control Active High Input for Play / Pause Control Active High Input for Volume Down Control Active High Input to activate the Bluetooth connection process Active High Input for Volume Up Control Programmable I/O pin Programmable I/O pin Not Connect Ground Microphone Bias Analog Input / Programmable I/O SPU SPD WPU WPD Strong Pull-up Strong Pull-down Weak Pull-up Weak Pull-down Analog Table 1 iBT-03 Pin Description Table 0.3.01 3/7 2012-07-30 iBT-03 Bluetooth Module for Audio Application 6. Electrical Specification 6.1. Absolute Maximum Rating Item Power Supply Voltage Peak Current Storage Temperature Symbol VDD Ipk TSTG Rating -0.4 to 3.7 0 - 70 -20 to 85 Unit mA °C 6.2. Recommended Operating Condition Item Power Supply Voltage RF Operating Temperature Operating Temperature Symbol VDD Miin 3.0 Typ 3.3 25 25 Max 3.6 80 55 Unit °C °C 6.3. Digital Input / Output Port Characteristics VDD=3.3V, operating temperature = 25 °C unless specified otherwise Symbol Parameter Condition Min. Input Voltage Levels VIL Input low voltage -0.3 VIH Input high voltage 0.625*VDD Vsch Schmitt voltage level 0.25*VDD Output Voltage Levels VOL Output low voltage IOL = -4mA VOH Output high voltage IOH = 4mA 0.75*VDD Input and Tri-state Current with Strong pull-up -100 Strong pull-down 10 Weak pull-up -5 Weak pull-down 0.2 I/O Pad leakage current -1 Input Capacitance Typ. -40 40 -1 Max. Unit 0.25*VDD VDD+0.3 0.625*VDD 0.125 VDD -10 100 -0.2 uA uA uA uA uA pF Max Unit mA 10.0 mA 10.0 mA 80.0 mA 6.4. Operating Current VDD=3.3V, operating temperature = 25 °C unless specified otherwise Item Symbol Miin Standby Mode 0.5 Pairing Mode 1.0 iBT-03 is discoverable by other devices Idle Mode iBT-03 is connectable with devices in the 1.0 connected list Audio Streaming Mode 40 0.3.01 4/7 Typ 2012-07-30 iBT-03 Bluetooth Module for Audio Application 6.5. RF Characteristics VDD=3.3V, operating temperature = 20 °C unless specified otherwise Receiver Sensitivity at 0.1% BER Maximum Receiver Signal at 0.1% BER C/I Co-Channel Adjacent Channel Selectivity C/I – +/-1MHz nd 2 Adjacent Channel Selectivity C/I – +2Mhz nd 2 Adjacent Channel Selectivity C/I – -2Mhz rd 3 Adjacent Channel Selectivity C/I – +/-3Mhz Units Miin dBm dBm dB dB dB dB dB Typ -85 -6 10 -4 -35 -21 -45 Max 11 -30 -20 Bluetooth Spec ≦ -70 ≧-20 ≦ 11 ≦0 ≦ -30 ≦ -20 ≦ -40 VDD=3.3V, operating temperature = 20 °C unless specified otherwise Transmitter RF Output Power RF Power Control Range RF Power Range Control Resolution 20dB Bandwidth for modulated Carrier nd 2 Adjacent Channel Power (+/- 2Mhz) rd 3 Adjacent Channel Power (+/- 3Mhz) 0.3.01 Units Miin Typ Max dBm dB dB kHz dBm dBm 16 35 1.8 879 -35 -45 5/7 1000 -20 -40 Bluetooth Spec -6 to +4 > 16 < 1000 ≦ -20 ≦ -40 2012-07-30 iBT-03 Bluetooth Module for Audio Application 7. Module Dimension and PCB Layout Guideline 7.1. Module Dimension 3.81mm 2.97mm iBT-03 Module (Top View) 2.54mm 2.41mm 1.46x5 = 7.3mm 0.95mm 11.94mm 2.54mm 1.46mm x 14 = 20.44mm R=0.38mm 23.24mm 5.33mm 0.8mm 1.66mm 2.54mm 7.2. PCB Layout Guideline 0.3.01 6/7 2012-07-30 iBT-03 Bluetooth Module for Audio Application 8. FCC Statement NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by ValenceTech Limited may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help Radiofrequency radiation exposure information: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Please see the RF Exposure information. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device should be installed and operated with a minimum distance of 20cm between the antenna and all persons. Label requirements: Contains Transmitter Module FCC ID: ORP-IBT-03 Host use instruction: The module must install and work with a speaker, the speaker's manufacturer is ValenceTech Limited. The Host model name: IBT03 BLUETOOTH SPEAKER SYSTEM The Host Brand Name: ValenceTech The host is a fixed device and the antenna used with this host should be installed and operated with a minimum distance of 20cm from all persons. FCC RF Exposure Requirement 1. At least 20cm separation distance between the antenna and the user's body must be maintained at all times. And must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi transmitter product procedures. 2. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure condition must not exceed 0dBi in the 2.4G band. 3. A user manual with the end product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines. Note: If this module is intended for use in a portable device, you are responsible for separate approval to satisfy the SAR requirements of FCC Part 2.1093. 0.3.01 7/7 2012-07-30 Please be noticed following information and instructions should be placed in the end-user’s operating manual The iBT-03 Module has been granted as limited modular approval for mobile applications. iBT-03 Module must be installed in the designated host as specified in this manual. 1. Separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations. 2. The iBT-03 Module and its antenna must not be co-located or operating in conjunction with any other transmitter or antenna within a host device. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. 3. A label must be affixed to the outside of the end product into which the iBT-03 module is incorporated, with a statement similar to the following: For iBT-03: This device contains FCC ID: ORP-IBT-03. 4. The module shall be in non-detachable construction protection into the finished products, so that the end-user has to destroy the module while remove or install it. 5. This module is to be installed only in mobile or fixed applications. According to FCC part 2.1091(b) definition of mobile and fixed devices is:. Mobile device: A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter’s radiating structure(s) and the body of the user or nearby persons. In this context, the term ‘‘fixed location’’ means that the device is physically secured at one location and is not able to be easily moved to another location. Portable device: For purposes of this section, a portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. 6. Separate approval is required for all other operating configurations, including portable configurations with respect to FCC Part 2.1093 and different antenna configurations. 7. A certified modular has the option to use a permanently affixed label, or an electronic label. For a permanently affixed label, the module must be labelled with an FCC ID: ORP-IBT-03. The OEM manual must provide clear instructions explaining to the OEM the labelling requirements, options and OEM user manual instructions that are required For a host using a this FCC certified modular with a standard fixed label, if (1) the module’s FCC ID is not visible when installed in the host, or (2) if the host is marketed so that end users do not have straightforward commonly used methods for access to remove the module so that the FCC ID of the module is visible; then an additional permanent label referring to the enclosed module: “Contains Transmitter Module FCC ID: ORP-IBT-03” or “Contains FCC ID: ORP-IBT-03” must be used. The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID. 8. Host product is required to comply with all applicable FCC equipment authorizations regulations, requirements and equipment functions not associated with the transmitter module portion. compliance must be GOODOCOM Technologies Confidential demonstrated to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15B). To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. If a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. Since this may depend on the details of how the module is integrated with the host, we suggest the host device to recertify part 15B to ensure complete compliance with FCC requirement: Part 2 Subpart J Equipment Authorization Procedures , KDB784748 D01 v07, and KDB 997198 about importation of radio frequency devices into the United States. GOODOCOM Technologies Confidential OEM RESPONSIBILITIES TO COMPLY WITH FCC REGULATIONS The iBT-03 Module has been certified for integration into products only by OEM integrators under the following conditions: This device is granted for use in Mobile only configurations in which the antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all person and not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. OEM LABELING REQUIREMENTS FOR END-PRODUCT The iBT-03 module is labeled with its own FCC ID Certification Number. The FCC ID certification numbers are not visible when the module is installed inside another device, as such the end device into which the module is installed must display a label referring to the enclosed module. The final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: ORP-IBT-03” or “Contains FCC ID: ORP-IBT-03” The OEM of the iBT-03 Module must only use the approved antenna(s) listed above, which have been certified with this module. The device iBT-03 carries FCC authorization and is marked with the FCC ID Number. Whilst any device into which this authorized module is installed will not normally be required to obtain FCC authorization, this does not preclude the possibility that some other form of authorization or testing may be required for the finished device. OEM END PRODUCT USER MANUAL STATEMENTS The OEM integrator should not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. If this module is intended for use in a portable device, you are responsible for separate approval to satisfy the SAR requirements of FCC Part 2.1093. The user manual for the end product must include the following information in a prominent location: This device is granted for use in Mobile only configurations in which the antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all person and not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures. The end product with an embedded FCC ID:ORP-IBT-03 Module may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized per FCC Part 15. The labeling instructions of finished products refer to following requirements: A certified modular has the option to use a permanently affixed label, or an electronic label (see Electronic Labelling below). For a permanently affixed label, the module must be labelled with an FCC ID - Section 2.926 (see Certification (labelling requirements) above). The OEM manual must provide clear instructions explaining to the OEM the labelling requirements,options and OEM user manual instructions that are required (see next paragraph). For a host using a certified modular with a standard fixed label, if (1) the module’ s FCC ID is not visible when installed in the host, or (2) if the host is marketed so that end users do not have straightforward commonly used methods for access to remove the module so that the FCC ID of the module is visible; then an additional permanent label referring to the enclosed module: “Contains Transmitter Module FCC ID: ORP-IBT-03” or “Contains FCC ID: ORP-IBT-03” must be used. The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID. Other user manual statements may apply. iBT-03 Bluetooth Module for Audio Application Valence Semiconductor Design Ltd. Unit 1, 20/F., APEC Plaza, 49 Hoi Yuen Road, Kwun Tong, Hong Kong Tel: (852) 2797 3288 Fax: (852) 2776 7770 http://www.valencetech.com The information in this publication is believed to be accurate in all respects at the time of publication but is subject to change without notice. Valence Semiconductor Design Ltd. assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Valence Semiconductor Design Ltd. assumes no responsibility for the functioning of undocumented features or parameters. 0.3.01 8/7 2012-07-30
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 About : uuid:7bf4c4dd-e4fe-11e1-0000-12062540ec8d Producer : GPL Ghostscript 9.05 Keywords : Modify Date : 2012:12:12 14:50:03+08:00 Create Date : 2012:08:10 12:21:58+08:00 Creator Tool : PDFCreator Version 1.4.1 Metadata Date : 2012:12:12 14:50:03+08:00 Document ID : uuid:7bf4c4dd-e4fe-11e1-0000-12062540ec8d Instance ID : uuid:552ccd6f-c2d5-453a-a6aa-e3e44124a21a Format : application/pdf Title : iBT-03-Rev0.3.01 - FCC Creator : hw.poon Description : () Page Count : 12 Subject : Author : hw.poonEXIF Metadata provided by EXIF.tools