ValenceTech IBT-03 BLUETOOTH MODULE User Manual iBT 03 Rev0 3 01 FCC

ValenceTech Limited BLUETOOTH MODULE iBT 03 Rev0 3 01 FCC

User Manual

iBT-03 Bluetooth Module for Audio Application 0.3.01 1 / 7 2012-07-30 iBT-03 Bluetooth Module for Audio Application ( Qualified QDID : B019566 ) Doc. Name : iBT-03-Rev0.3.01 Date : 2012-07-30 Revision : 0.3.01 This module is limited to OEM Installation only. Copyright ©, 2012 by Engineering Department, Valence Semiconductor Design Limited. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means without the prior written permission of Valence Semiconductor Design Limited.
iBT-03 Bluetooth Module for Audio Application 0.3.01 2 / 7 2012-07-30 1. Overview iBT-03 is a Class 2 Bluetooth module supporting Bluetooth V2.1 + EDR specification. It is implemented by using the CSR BlueCore5-Multimedia ROM chip. iBT-03 is designed for receiving audio data transmitting from a mobile device. It can also be used to control the audio playing function of the remote device 2. Features  A single chip radio and baseband IC for Bluetooth applications  Fully Qualified Bluetooth v2.1+EDR (Enhanced Data Rate)  Class 2 power output (10 Meter minimum)  Support for 802.11 co-existence  High quality 95dB SNR DAC playback  LED drivers and faders  Supporting profiles : A2DP, AVRCP  Build-in PCB antenna  Supply voltage : 3.0V to 3.6V  RoHS compliant  Dimension: 31.0mm (L) x 12mm (W) x 2.6mm (H) 3. Applications  Wireless speakers  Stereo headset  Hands-free car kit  VoIP handsets  Docking Stations 4. Pin Drawing 27 SPI_CSB22 GND24 SPI_CLK36 GND35 NC28 PIO1229 PIO1130 PIO531 PIO332 PIO233 PIO023 RESETB25 SPI_MISO26 SPI_MOSI34 PIO13.3V 9MIC_BP 10PIO13 8MIC_BN 11SPK_LP 5SPK_LN 4SPK_RP 7SPK_RN 6MIC_AP 2MIC_AN 3PIO9 14PIO4 15PIO14 13GND 1GND 12 Figure 1 iBT-03 Pin Diagram
iBT-03 Bluetooth Module for Audio Application 0.3.01 3 / 7 2012-07-30 5. Pin Description Pin No. Pin Name Application Usage Pin Type Pin Descriptions 1 GND GND Ground 2 MIC_AP AI Microphone A Positive Input 3 MIC_AN AI Microphone A Negative Input 4 SPK_LN SPK_LN AO Negative Output of Left Speaker 5 SPK_LP SPK_LP AO Positive Output of Left Speaker 6 SPK_RN SPK_RN AO Negative Output of Right Speaker 7 SPK_RP SPK_RP AO Positive Output of Right Speaker 8 PIO13 STBY / ON I Active High Input for ON / OFF control When iBT-03 is OFF, a high pulse in this pin will turn it ON. When iBT-03 is in ON, a high pulse in this pin will turn in OFF 9 3.3V 3.3V 3.3V Supply Input 10 MIC_BP AI Microphone B Positive Input 11 MIC_BN AI Microphone B Negative Input 12 GND GND Ground 13 PIO14 REV I Active High Input for Reverse Control 14 PIO9 PAIR I Perform Pair function 15 PIO4 AMP_SDB O4 Active Low signal for shutting down the external Amplifier 16 GND GND Ground 17 BT_TX O4, PU UART Data Output 18 BT_RX IS, PD UART Data Input 19 AIO1 A, B Analog / Programmable I/O 20 LED0 LED0 OD4 Open Drain LED Driver Output 21 LED1 LED1 OD4 Open Drain LED Driver Output 22 GND GND Ground 23 RESETB RESETB IS, PU Active Low Module Reset. Must be low for > 5mS 24 SPI_CLK SPI_CLK IS, PD Serial Peripheral Interface Clock 25 SPI_MISO SPI_MISO O4, PD Serial Peripheral Output Data 26 SPI_MOSI SPI_MOSI IS, PD Serial Peripheral Input Data 27 SPI_CSB SPI_CSB IS, PU Active Low Chip Select for Serial Peripheral Interface 28 PIO12 FWD I Active High Input for Forward Control 29 PIO11 PLAY/PAUSE I Active High Input for Play / Pause Control 30 PIO5 VOL_DOWN I Active High Input for Volume Down Control 31 PIO3 CONNECT I Active High Input to activate the Bluetooth connection process 32 PIO2 VOL_UP I Active High Input for Volume Up Control 33 PIO0 B Programmable I/O pin 34 PIO1 B Programmable I/O pin 35 NC Not Connect 36 GND GND Ground 37 MIC_BIAS A Microphone Bias 38 AIO0 A, B Analog Input / Programmable I/O O4 4mA output pad OD Open drain output pad I Input IS Schmidt Trigger Input B Bidirectional SPU Strong Pull-up SPD Strong Pull-down WPU Weak Pull-up WPD Weak Pull-down A Analog Table 1 iBT-03 Pin Description Table
iBT-03 Bluetooth Module for Audio Application 0.3.01 4 / 7 2012-07-30 6. Electrical Specification 6.1. Absolute Maximum Rating Item Symbol Rating Unit Power Supply Voltage VDD -0.4 to 3.7 V Peak Current Ipk 0 - 70 mA Storage Temperature TSTG -20 to 85 °C 6.2. Recommended Operating Condition Item Symbol Miin Typ Max Unit Power Supply Voltage VDD 3.0 3.3 3.6 V RF Operating Temperature 0 25 80 °C Operating Temperature 0 25 55 °C 6.3. Digital Input / Output Port Characteristics VDD=3.3V, operating temperature = 25 °C unless specified otherwise Symbol Parameter Condition Min. Typ. Max. Unit Input Voltage Levels VIL Input low voltage -0.3 0.25*VDD V VIH Input high voltage 0.625*VDD VDD+0.3 V Vsch Schmitt voltage level 0.25*VDD 0.625*VDD V Output Voltage Levels VOL Output low voltage IOL = -4mA 0.125 V VOH Output high voltage IOH = 4mA 0.75*VDD VDD V Input and Tri-state Current with Strong pull-up -100 -40 -10 uA Strong pull-down 10 40 100 uA Weak pull-up -5 -1 -0.2 uA Weak pull-down 0.2 1 5 uA I/O Pad leakage current -1 0 1 uA Input Capacitance 1 5 pF 6.4. Operating Current VDD=3.3V, operating temperature = 25 °C unless specified otherwise Item Symbol Miin Typ Max Unit Standby Mode 0.5 2 mA Pairing Mode iBT-03 is discoverable by other devices 1.0 10.0 mA Idle Mode iBT-03 is connectable with devices in the connected list 1.0 10.0 mA Audio Streaming Mode 40 80.0 mA
iBT-03 Bluetooth Module for Audio Application 0.3.01 5 / 7 2012-07-30 6.5. RF Characteristics VDD=3.3V, operating temperature = 20 °C unless specified otherwise Receiver Units Miin Typ Max Bluetooth Spec Sensitivity at 0.1% BER dBm -85 ≦ -70 Maximum Receiver Signal at 0.1% BER dBm -6 ≧-20 C/I Co-Channel dB 10 11 ≦ 11 Adjacent Channel Selectivity C/I – +/-1MHz dB -4 0 ≦ 0 2nd Adjacent Channel Selectivity C/I – +2Mhz dB -35 -30 ≦ -30 2nd Adjacent Channel Selectivity C/I – -2Mhz dB -21 -20 ≦ -20 3rd Adjacent Channel Selectivity C/I – +/-3Mhz dB -45 ≦ -40 VDD=3.3V, operating temperature = 20 °C unless specified otherwise Transmitter Units Miin Typ Max Bluetooth Spec RF Output Power dBm 0 2 4 -6 to +4 RF Power Control Range dB 16 35 > 16 RF Power Range Control Resolution dB 1.8 - 20dB Bandwidth for modulated Carrier kHz 879 1000 < 1000 2nd Adjacent Channel Power (+/- 2Mhz) dBm -35 -20 ≦ -20 3rd Adjacent Channel Power (+/- 3Mhz) dBm -45 -40 ≦ -40
iBT-03 Bluetooth Module for Audio Application 0.3.01 6 / 7 2012-07-30 7. Module Dimension and PCB Layout Guideline 7.1. Module Dimension 1.46mm x 14 = 20.44mm0.95mm23.24mm11.94mmiBT-03 Module(Top View)5.33mm2.54mm2.41mm2.97mm3.81mm2.54mm1.66mm2.54mm1.46x5 = 7.3mmR=0.38mm 0.8mm 7.2. PCB Layout Guideline
iBT-03 Bluetooth Module for Audio Application 0.3.01 7 / 7 2012-07-30 8. FCC Statement NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by ValenceTech Limited may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help Radiofrequency radiation exposure information: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Please see the RF Exposure information. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device should be installed and operated with a minimum distance of 20cm between the antenna and all persons. Label requirements: Contains Transmitter Module FCC ID: ORP-IBT-03 Host use instruction: The module must install and work with a speaker, the speaker's manufacturer is ValenceTech Limited.The Host model name: IBT03 BLUETOOTH SPEAKER SYSTEMThe Host Brand Name: ValenceTech The host is a fixed device and the antenna used with this host should be installed and operated with a minimum distance of 20cm from all persons. FCC RF Exposure Requirement 1. At least 20cm separation distance between the antenna and the user's body must be maintained at all times. And must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi transmitter product procedures. 2. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure condition must not exceed 0dBi in the 2.4G band. 3. A user manual with the end product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines. Note: If this module is intended for use in a portable device, you are responsible for separate approval to satisfy the SAR requirements of FCC Part 2.1093.
GOODOCOM Technologies Confidential Please be noticed following information and instructions should be placed in the end-user’s operating manual The iBT-03 Module has been granted as limited modular approval for mobile applications. iBT-03 Module must be installed in the designated host as specified in this manual. 1. Separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations. 2. The iBT-03 Module and its antenna must not be co-located or operating in conjunction with any other transmitter or antenna within a host device. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. 3. A label must be affixed to the outside of the end product into which the iBT-03 module is incorporated, with a statement similar to the following: For iBT-03: This device contains FCC ID: ORP-IBT-03. 4. The module shall be in non-detachable construction protection into the finished products, so that the end-user has to destroy the module while remove or install it. 5. This module is to be installed only in mobile or fixed applications. According to FCC part 2.1091(b) definition of mobile and fixed devices is:. Mobile device: A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter’s radiating structure(s) and the body of the user or nearby persons. In this context, the term ‘‘fixed location’’ means that the device is physically secured at one location and is not able to be easily moved to another location. Portable device: For purposes of this section, a portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. 6. Separate approval is required for all other operating configurations, including portable configurations with respect to FCC Part 2.1093 and different antenna configurations. 7. A certified modular has the option to use a permanently affixed label, or an electronic label. For a permanently affixed label, the module must be labelled with an FCC ID: ORP-IBT-03. The OEM manual must provide clear instructions explaining to the OEM the labelling requirements, options and OEM user manual instructions that are required For a host using a this FCC certified modular with a standard fixed label, if (1) the module’s FCC ID is not visible when installed in the host, or (2) if the host is marketed so that end users do not have straightforward commonly used methods for access to remove the module so that the FCC ID of the module is visible; then an additional permanent label referring to the enclosed module: “Contains Transmitter Module FCC ID: ORP-IBT-03” or “Contains FCC ID: ORP-IBT-03” must be used. The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID. 8. Host product is required to comply with all applicable FCC equipment authorizations regulations, requirements and equipment functions not associated with the transmitter module portion. compliance must be
GOODOCOM Technologies Confidential demonstrated to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15B). To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. If a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. Since this may depend on the details of how the module is integrated with the host, we suggest the host device to recertify part 15B to ensure complete compliance with FCC requirement: Part 2 Subpart J Equipment Authorization Procedures , KDB784748 D01 v07, and KDB 997198 about importation of radio frequency devices into the United States.
OEM RESPONSIBILITIES TO COMPLY WITH FCC REGULATIONSThe iBT-03 Module has been certified for integration into products only by OEMintegrators under the following conditions:This device is granted for use in Mobile only configurations in which the antennasused for this transmitter must be installed to provide a separation distance ofat least 20cm from all person and not be co-located with any other transmittersexcept in accordance with FCC and Industry Canada multi-transmitter productprocedures.As long as the two conditions above are met, further transmitter testing will notbe required.However, the OEM integrator is still responsible for testing their end-productfor any additional compliance requirements required with this module installed(for example, digital device emissions, PC peripheral requirements, etc.).IMPORTANT NOTE: In the event that these conditions cannot be met (for certainconfigurations or co-location with another transmitter), then the FCC and IndustryCanada authorizations are no longer considered valid and the FCC ID and ICCertification Number cannot be used on the final product. In these circumstances,the OEM integrator will be responsible for re-evaluating the end product (includingthe transmitter) and obtaining a separate FCC and Industry Canada authorization.OEM LABELING REQUIREMENTS FOR END-PRODUCTThe iBT-03 module is labeled with its own FCC ID Certification Number. The FCCID certification numbers are not visible when the module is installed inside anotherdevice, as such the end device into which the module is installed must displaya label referring to the enclosed module. The final end product must be labeledin a visible area with the following:“Contains Transmitter Module FCC ID: ORP-IBT-03”or“Contains FCC ID: ORP-IBT-03”The OEM of the iBT-03 Module must only use the approved antenna(s) listed above,which have been certified with this module.The device iBT-03 carries FCC authorization and is marked with the FCC ID Number.Whilst any device into which this authorized module is installed will not normallybe required to obtain FCC authorization, this does not preclude the possibility
that some other form of authorization or testing may be required for the finisheddevice.OEM END PRODUCT USER MANUAL STATEMENTSThe OEM integrator should not to provide information to the end user regardinghow to install or remove this RF module or change RF related parameters in theuser manual of the end product.If this module is intended for use in a portable device, you are responsible forseparate approval to satisfy the SAR requirements of FCC Part 2.1093.The user manual for the end product must include the following information in aprominent location:This device is granted for use in Mobile only configurations in which the antennasused for this transmitter must be installed to provide a separation distance ofat least 20cm from all person and not be co-located with any other transmittersexcept in accordance with FCC and Industry Canada multi-transmitter productprocedures.The end product with an embedded FCC ID:ORP-IBT-03 Module may also need to passthe FCC Part 15 unintentional emission testing requirements and be properlyauthorized per FCC Part 15.The labeling instructions of finished products refer to following requirements:A certified modular has the option to use a permanently affixed label, or anelectronic label (see Electronic Labelling below). For a permanently affixed label,the module must be labelled with an FCC ID - Section 2.926 (see Certification(labelling requirements) above). The OEM manual must provide clear instructionsexplaining to the OEM the labelling requirements,options and OEM user manualinstructions that are required (see next paragraph).For a host using a certified modular with a standard fixed label, if (1) the module’s FCC ID is not visible when installed in the host, or (2) if the host is marketedso that end users do not have straightforward commonly used methods for accessto remove the module so that the FCC ID of the module is visible; then an additionalpermanent label referring to the enclosed module:“Contains Transmitter Module FCC ID: ORP-IBT-03”or “Contains FCC ID: ORP-IBT-03”must be used. The host OEM user manual must also contain clear instructions onhow end users can find and/or access the module and the FCC ID.Other user manual statements may apply.
iBT-03 Bluetooth Module for Audio Application 0.3.01 8 / 7 2012-07-30 Valence Semiconductor Design Ltd. Unit 1, 20/F., APEC Plaza, 49 Hoi Yuen Road, Kwun Tong, Hong Kong Tel: (852) 2797 3288 Fax: (852) 2776 7770 http://www.valencetech.com The information in this publication is believed to be accurate in all respects at the time of publication but is subject to change without notice. Valence Semiconductor Design Ltd. assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Valence Semiconductor Design Ltd. assumes no responsibility for the functioning of undocumented features or parameters.

Navigation menu