ValenceTech IBT0602S Bluetooth Module User Manual iBT 06 02S Rev0 5 02

Download:
Mirror Download [FCC.gov]
Document ID	2193364
Application ID	/AHxDQhaJp1/+LADa9STjA==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	45.09kB (563671 bits)
Date Submitted	2014-02-19 00:00:00
Date Available	2014-02-19 00:00:00
Creation Date	2014-01-22 18:13:53
Producing Software	GPL Ghostscript 9.05
Document Lastmod	2014-02-19 09:28:15
Document Title	iBT-06-02S-Rev0.5.02
Document Creator	PDFCreator Version 1.5.0
Document Author:	hw.poon

iBT-06-02S
Bluetooth Module with HCI Interface
iBT-06-02S
Bluetooth Module with HCI Interface
Qualified QDID : B021756 )
FCC ID:ORP-IBT0602S
IC:11691A-IBT0602S
Doc. Name
Date
Revision
iBT-06-02S-Rev0.5.02.doc
2013-11-21
0.5.02
Copyright ©, 2013 by Engineering Department, Valence Semiconductor Design Limited.
All rights reserved. No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language, in any form or by any means
without the prior written permission of Valence Semiconductor Design Limited.
0.5.02
1 / 11
2013-11-21
iBT-06-02S
Bluetooth Module with HCI Interface
1. Overview
iBT-06-02S is a Class 2 Bluetooth module supporting Bluetooth v2.1 + EDR specification. It is implemented by using the
RDA5876a chip. iBT-06-02S is designed to interface with an external MCU with HCI command control for supporting audio or
data applications.
2. Features
A single chip radio and baseband module for
Bluetooth applications
Fully Qualified Bluetooth v2.1+EDR
Class 2 power output (10 meter minimum)
Support for 2-wires / 3-wires 802.11 co-existence
HCI Interface to external MCU
Build-in PCB antenna
Supply voltage : 3.3V to 4.2V
RoHS compliant
Dimension:
iBT-06-02S :21.5mm (L) x 14mm (W) x 2.2mm (H)
3. Applications
Wireless speakers
Stereo headset
Hands-free car kit
VoIP handsets
Data Transfer
Docking Stations
4. Pin Drawing
Figure 1 iBT-06-02S Pin Diagram
0.5.02
2 / 11
2013-11-21
iBT-06-02S
Bluetooth Module with HCI Interface
5. Block Diagram
PCM_CLK
PCM_SYNC
PCM_DOUT
PCM_DIN
GND
Figure 2 iBT-06-02S Block Diagram
6. Pin Description
Pin No
Pin Name
Pin Type
10
11
12
13
14
15
16
BT_ACTIVE
BT_PRIORITY
WLAN_ACTIVE
BT_EINT
BT_TX
BT_RX
PCM_SYNC
PCM_CLK
PCM_DIN
PCM_DOUT
VIO
VDD
GND
CLK_32K
I2C_SDA
I2C_SCL
17
LDO_ON
0.5.02
output pad
Input
Pin Descriptions
A “1” indicates that BT is active transmitting data
A “1” indicates that BT request to have priority over WLAN
A “1” indicates that WLAN is active transmitting data
Active high signal to interrupt external MCU
Bluetooth UART Data Output
Bluetooth UART Data Input
PCM data sync
PCM data clock
PCM data input
PCM data output
I/O Supply Voltage
Module Supply Voltage
Module Ground
External 32kHz Clock input
I2C Data Signal
I2C Clock Signal
Control signal to enable/disable the internal LDO that provide power to the
internal core. This control signal will also reset the internal core logic.
‘1’ Enable LDO
‘0’ LDO disable
IA
OA
Analog Input
Analog Output
3 / 11
2013-11-21
iBT-06-02S
Bluetooth Module with HCI Interface
7. Electrical Specification
7.1. Absolute Maximum Rating
Item
Module Supply Voltage
I/O Supply Voltage
Peak Current
Storage Temperature
Symbol
VDD
VIO
Ipk
TSTG
Rating
-0.4 to 4.5
-0.4 – 4.0
0 - 70
-20 to 85
Unit
mA
°C
7.2. Recommended Operating Condition
Item
Module Supply Voltage
I/O Supply Voltage
RF Operating Temperature
Operating Temperature
Symbol
VDD
VIO
Miin
3.3
1.8
Typ
25
25
Max
4.2
3.3
60
55
Unit
°C
°C
7.3. Digital Input / Output Port Characteristics
VDD=3.3V, VIO=3.3V, operating temperature = 25 °C unless specified otherwise
Symbol
Parameter
Condition
Min.
Typ.
Input Voltage Levels
VIL
Input low voltage
-0.3
VIH
Input high voltage
0.7*VIO
Vsch
Schmitt voltage level
0.3*VIO
Output Voltage Levels
VOL
Output low voltage
IOL = -4mA
VOH
Output high voltage
IOH = 4mA
0.75*VIO
Current Consumption
Depends on
Operating Current
25
profiles
Standby Current
0.5.02
4 / 11
Max.
Unit
0.25*VIO
VIO+0.3
0.7*VIO
0.125
VIO
mA
0.5
mA
2013-11-21
iBT-06-02S
Bluetooth Module with HCI Interface
7.4. RF Characteristics
VDD=4.0V, operating temperature = 27 °C unless specified otherwise
Receiver
Sensitivity at 0.1% BER
Maximum Receiver Signal at 0.1% BER
C/I Co-Channel
Adjacent Channel Selectivity C/I +1MHz
Adjacent Channel Selectivity C/I -1MHz
nd
2 Adjacent Channel Selectivity C/I +2Mhz
nd
2 Adjacent Channel Selectivity C/I -2Mhz
rd
3 Adjacent Channel Selectivity C/I +3Mhz
rd
3 Adjacent Channel Selectivity C/I -3Mhz
Units
dBm
dBm
dB
dB
dB
dB
dB
dB
dB
Miin
Typ
Max
-85
10
-5
-33
-30
-45
-40
Bluetooth
Spec
≦ -70
≧-20
≦ 11
≦0
≦0
≦ -30
≦ -20
≦ -40
≦ -40
VDD=4.0V, operating temperature = 27 °C unless specified otherwise
Transmitter
RF Output Power
RF Power Control Range
20dB Bandwidth for modulated Carrier
Basic Data Rate Adjacent Channel Power
nd
2 Adjacent Channel (+/- 2Mhz)
rd
3 Adjacent Channel (+/- 3Mhz)
Enhance Data Rate Adjacent Channel Power
st
1 Adjacent Channel (+/- 1MHz)
nd
2 Adjacent Channel (+/- 2Mhz)
rd
3 Adjacent Channel (+/- 3Mhz)
Initial Carrier Frequency Tolerance
0.5.02
Max
Bluetooth
Spec
2.4
760
-6 to +4
> 16
< 1000
dBm
dBm
-35
-40
≦ -20
≦ -40
dBm
dBm
dBm
kHz
-37
-32
-40
≦ -29
≦ -20
≦ -40
-75 to +75
Units
Miin
dBm
dBm
kHz
-28
5 / 11
Typ
1.6
-0.25
2013-11-21
iBT-06-02S
Bluetooth Module with HCI Interface
8. Module Dimension
8.1. iBT-06-02S Module Dimension
0.5.02
6 / 11
2013-11-21
iBT-06-02S
Bluetooth Module with HCI Interface
9. PCB Layout Guidelines
9.1. iBT-06-02S Antenna Clearance
9.2. iBT-06-02S PCB Landing Pattern
0.5.02
7 / 11
2013-11-21
iBT-06-02S
Bluetooth Module with HCI Interface
10. Regulatory Approval
This section outlines the regulatory information for the iBT-06-02S module for the following countries:
United States
Canada
Japan
10.1. United States
The iBT-06-02S module has received Federal Communications Commission (FCC) CFR47 Telecommunications, Part 15 Subpart
C “Intentional Radiators” modular approval in accordance with Part 15.212 Modular Transmitter approval. Modular approval
allows the (OEM) Integator to integrate the RN52 module in to a finished product without obtaining subsequent and separate FCC
approvals for intentional radiation, provided no changes or modifications are made to the module circuitry. Changes or
modifications could void the user’s authority to operate the equipment. The end user must comply with all of the instructions
provided by the Grantee, which indicate installation and/or operating conditions necessary for compliance.
The finished product is required to comply with all applicable FCC equipment authorizations regulations, requirements and
equipment functions not associated with the transmitter module portion. For example, compliance must be demonstrated to
regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15 Subpart
B “Unintentional Radiators”), such as digital devices, computer peripherals, radio receivers, etc.; and to additional authorization
requirements for the non-transmitter functions on the transmitter module (i.e., Verification, or Declaration of Conformity) (e.g.,
transmitter modules may also contain digital logic functions) as appropriate.
10.1.1. Labeling and User Information Requirements
The iBT-06-02S module has been labeled with its own FCC ID number, and if the FCC ID is not visible when the module is
installed inside another device, then the outside of the finished product into which the module is installed must also display a label
referring to the enclosed module. This exterior label can use wording as follows:
Contains Transmitter Module FCC ID: ORP-IBT0602S
This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation
Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority to operate the equipment.
A user’s manual for the product should include the following statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
Additional information on labeling and user information requirements for Part 15 devices can be found in KDB Publication
784748 available atthe FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB)
http://apps.fcc.gov/oetcf/kdb/index.cfm.
0.5.02
8 / 11
2013-11-21
iBT-06-02S
Bluetooth Module with HCI Interface
10.1.2. RF Exposure
All transmitters regulated by FCC must comply with RF exposure requirements. OET Bulletin 65, Evaluating Compliance with
FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields, provides assistance in determining whether
proposed or existing transmitting facilities, operations or devices comply with limits for human exposure to Radio Frequency (RF)
fields adopted by the Federal Communications Commission (FCC). The bulletin offers guidelines and suggestions for evaluating
compliance.
If appropriate, compliance with exposure guidelines for mobile and unlicensed devices can be accomplished by the use of warning
labels and by providing users with information concerning minimum separation distances from transmitting structures and proper
installation of antennas.
The following statement must be included as a CAUTION statement in manuals and OEM products to alert users of FCC RF
exposure compliance:
EUT has ultra-low output power so that it can be integrated in any host device without
any specific RF exposure limitations
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
If the iBT-06-02S module is used in a portable application (i.e., the antenna is less than20 cm from persons during operation), the
integrator is responsible for performing Specific Absorption Rate (SAR) testing in accordance with FCC rules 2.1091.
10.1.3. Helpful Web Sites
Federal Communications Commission (FCC): http://www.fcc.gov
FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB):
http://apps.fcc.gov/oetcf/kdb/index.cfm
10.2. Canada
The iBT-06-02S module has been certified for use in Canada under Industry Canada (IC) Radio Standards Specification (RSS)
RSS-210 and RSSGen. Modular approval permits the installation of a module in a host device
without the need to recertify the device.
10.2.1. Labeling and User Information Requirements
Labeling Requirements for the Host Device (from Section 3.2.1, RSS-Gen, Issue 3, December 2010): The host device shall be
properly labeled to identify the module within the host device.
The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise
the host device must be labeled to display the Industry Canada certification number of the module, preceded by the words
“Contains transmitter module”, or the word “Contains”, or similar wording expressing the same meaning, as follows:
Contains transmitter module IC: 11691A-IBT0602S
User Manual Notice for License-Exempt Radio Apparatus (from Section 7.1.3 RSS-Gen, Issue 3, December 2010): User manuals
for license-exempt radio apparatus shall contain the following or equivalent notice in a conspicuous location in the user manual or
alternatively on the device or both:
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
0.5.02
9 / 11
2013-11-21
iBT-06-02S
Bluetooth Module with HCI Interface
Transmitter Antenna (from Section 7.1.2 RSS-Gen,Issue 3, December 2010): User manuals for transmitters shall display the
following notice in a conspicuous location:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gainapproved for the transmitter by Industry Canada. Toreduce potential radio interference to other users,the antenna type and
its gain should be so chosen thatthe equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
The above notice may be affixed to the device instead of displayed in the user manual.
10.2.1. Helpful Web Sites
Industry Canada: http://www.ic.gc.ca/
0.5.02
10 / 11
2013-11-21
iBT-06-02S
Bluetooth Module with HCI Interface
Valence Semiconductor Design Ltd.
Unit 1, 20/F., APEC Plaza, 49 Hoi Yuen Road, Kwun Tong, Hong Kong
Tel: (852) 2797 3288
Fax: (852) 2776 7770
http://www.valencetech.com
The information in this publication is believed to be accurate in all respects at the time of publication but is subject to change without notice. Valence
Semiconductor Design Ltd. assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of
information included herein. Additionally, Valence Semiconductor Design Ltd. assumes no responsibility for the functioning of undocumented features or
parameters.
0.5.02
11 / 11
2013-11-21

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-701
About                           : uuid:69b5fcf0-85a9-11e3-0000-d5b8b5227af0
Producer                        : GPL Ghostscript 9.05
Keywords                        : 
Modify Date                     : 2014:02:19 09:28:15+08:00
Create Date                     : 2014:01:22 18:13:53+08:00
Creator Tool                    : PDFCreator Version 1.5.0
Metadata Date                   : 2014:02:19 09:28:15+08:00
Document ID                     : uuid:69b5fcf0-85a9-11e3-0000-d5b8b5227af0
Instance ID                     : uuid:889f778b-e18a-4065-af94-9708da3be6aa
Format                          : application/pdf
Title                           : iBT-06-02S-Rev0.5.02
Creator                         : hw.poon
Description                     : ()
Page Count                      : 11
Subject                         : 
Author                          : hw.poon

EXIF Metadata provided by EXIF.tools