Vantage Controls AP2RL AP2 Series lighting control devices User Manual Exhibit 8

Vantage Controls Inc. AP2 Series lighting control devices Exhibit 8

UserManual.wiki >

Vantage Controls >

AP2RL User Manual

Exhibit 8

V A N T A G E® Installation 1061 SOUTH 800 EAST • OREM, UTAH 84097 • TELEPHONE 801.229.2800 • FACSIMILE 801.224.0355 • www.vantagecontrols.com Overview The Vantage AccentPoint Relay II connects to the Vantage Control System through RadioLink®. It enables an appliance to be controlled by a keypad, timed event, IR button, etc. It has two loads and one button for each load with default programming to allow for local control of the appliance whether the station is communicating with the Vantage system or not. Specifications Description Specification Dimensions, HWD 4.125” x 3.125” x 1.25” 107.95mm x 79.37mm x 31.75mm Weight 5.8 oz - 164g Mounting Plugs into standard 120VAC Outlet Voltage 120V, 60Hz Max. Load • 16A (shared between both outlets) for General Purpose AC, Magnetic Low-Voltage, and resistive loads, i.e., if one outlet is using the full 16A limit, the other outlet must not be used. • 1 Horsepower (16A) for motor loads • 8A per outlet (16A total) for incandescent loads Lightning / Surge Protection High Voltage meets IEEE C62.41 (6000V & 3000A) Low Voltage meets ITU-T K.20 Station Equivalent 1 RadioLink Station Ambient Operating Temperature 32 - 95°F -or- 0 - 35°C Ambient Operating Humidity 5 - 95% non-condensing LED Indicator Status Load Types General purpose AC, magnetic Low-voltage, and resistive loads, motor loads, incandescent loads UL and CUL Listed Yes FCC Yes System Requirements This station is compatible with InFusion Design Center Systems. For new projects it is recommended that firmware and software be kept to the most current release. Installation Installation of Vantage products should be performed or supervised by a Certified Vantage Installer. 1. Make sure the appliance to be controlled is turned OFF. 2. Plug the appliance into the load 1 or load 2 outlet on the bottom of the AccentPoint. 3. Plug the AccentPoint into the bottom receptacle of a power outlet. Notice the plug of the AccentPoint Relay II Station may be rotated 180°. If the GND prong on the outlet is UP, rotate the plug as illustrated so the Load Outlets are facing down (recommended). 4. Turn the appliance switch to ON 5. It is now ready to be controlled by the Vantage system. Steps to Rotate the Outlet The plug should only be rotated once. Only rotate when necessary as described in step 3 above. 1. Use a precision grade Phillips #1 screw driver to remove the screw from the plug assembly of the station. 2. Pull the plug assembly out by hand and rotate it 180° 3. Reinsert the plug by hand. Line it up and press it in until the face of the plug assembly is flush with the case. 4. Fasten the plug assembly with the screw removed in step 1. 5. Do not over tighten. Station Set Up in Design Center Software 1. Select the room 2. Click on Vantage Objects in the Object Explorer and expand Stations, RadioLink. 3. From the list of stations double click on the AccentPoint Relay II station to place it in the room. 4. In the Object Editor, name the station and make sure it is on the correct RadioLink bus port. Configuration RadioLink stations need to be configured to associate which physical station goes with the station in software. When the station is initially powered-up, the Status LED will blink three times followed by a pause - this means the station is powered correctly but not yet on the network. Before uploading the file to the Vantage system, do the following: 1. In Design Center with the AccentPoint Relay II highlighted, in the Object Editor click in the Serial Number section 2. Manually type in the serial number of the AccentPoint Dimmer II station. enter the serial number for each RadioLink 3. Repeat for each AccentPoint Relay II station 4. TIP: The serial number of each station is located on a permanent sticker on the station. Record this number for easy reference when programming in Design Center. 5. When the InFusion System is programmed, the Main Controller will add all RadioLink stations that it has serial numbers for. This may take several minutes depending on the number of RadioLink stations on the network. 6. The Status LED will blink steadily when logged on to the network. Device Operation The AccentPoint Relay II is designed to be controlled from a separate keypad, timed event or other control on the Vantage System. It also has a button for local control of each load. The buttons operate with default programming whether or not the device is communicating with the Vantage System. Pressing the buttons toggle the loads on and off. When power is restored from a power outage the device will return the load to the last load state. This will occur whether or not the station is connected to a system. Reset The device stores the configuration data locally so that it will continue to operate correctly if communication with the system is lost. To reset this information to the factory default, unplug the device, press and hold both buttons in and plug it in while holding the buttons down. After a reset the load will be off, and other settings will be at factory default. Note: Make sure it is back on-line with the Master Controller before testing button or load operation. RadioLink® AccentPoint Relay II — APREL

Diagnostic Information A red Status LED is located on top of the device. The Status LED blinks evenly or flashes 2, 3, or 4 times followed by a pause to indicate status information. Off: The station is not powered. A line voltage connection has not been made or the line feed breaker is off. One Even blink: Station is operating correctly and is configured. Two blinks: Station should be reset. See Reset above. Three blinks: Station is not added to the network. Verify that its serial number has been programmed into the Main Controller using QLink and that the station is within 100 Feet of the RFE1000. Four blinks: AccentPoint Relay II problem. Please contact the factory. FCC Compliance Information: FCC ID: PII-AP2RL IC: 3505A-AP2RL The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this product not expressly approved by Vantage Controls could void the user’s authority to operate this product. 39493 / InFusion compatible Warranty at: http://www.vantagecontrols.com/warranty ©Vantage Controls