Venstar RFM Thermostat RF Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1179788
Application ID	yzczL9YQ+SKQGvkpEAsiWw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	51.56kB (644496 bits)
Date Submitted	2009-10-02 00:00:00
Date Available	2009-10-02 00:00:00
Creation Date	2009-07-27 21:00:49
Producing Software	Corel PDF Engine Version 3.0.0.739
Document Lastmod	2009-07-27 21:00:49
Document Title	S1-LXRFM Thermostat RF Module Owner's Manual Rev. 3
Document Creator	CorelDRAW
Document Author:	Mike McLaury

S1-LXRFM
Thermostat RF Module
S1-LXRFM LX SERIES THERMOSTAT RF MODULE FEATURES:
2-way wireless communication
Links wireless sensors and accessories to the thermostat
Frequency hopper to avoid interference
Easy, 2 minute installation
Compatible with these thermostats:
S1-THSU21P1_, S1-THSU32P7_, S1-THSU32HP7_,
S1-TBSU22HN_, S1-TBSU32P7_, S1-TBSU32HP7_
Consult Source 1 for a complete list.
THERMOSTAT RF MODULE
Installation
Remove the thermostat Backplate.
To remove the thermostat backplate:
Using the Finger Pull Areas, pull the front housing
away from the backplate.
Backplate
Install the Thermostat RF Module.
Line up the Guide Pins on the Thermostat RF
Module with the holes on the printed circuit board.
Push gently until the Thermostat RF Module lays
flat against the board.
Make sure to remove the Thermostat RF Module
port cover before installation.
GUIDE PINS
Installation
Front Housing
Patent Pending
Finger Pull Areas
P/N 88-811
Rev. 3
THERMOSTAT RF MODULE
S1-LXRFM
Linking and Viewing Wireless Devices
Press the LINK button or the button designated for linking on the wireless device.
Press the ACCSRY button on the thermostat to enter the Accessory setup screen. (see illustration below)
Press the COOLER button to enter accessory linking mode or press WARMER to view linked accessories.
If COOLER is pressed, press the MODE button to initiate accessory linking. The thermostat will attempt to link
to the wireless device for 5 minutes. When the wireless device has been successfully linked, the thermostat will
display the following:
The name of the wireless device
The ID number of the wireless device (when applicable, as with Indoor Wireless Temp Sensors)
The signal strength of the wireless device (1 to 10)
The amount of time since the wireless device last communicated (Ex. “3 MN 13 SEC SINCE LAST UPDATE”)
The battery level of the wireless device (25%, 50%, 75%, or 100%)
If WARMER is pressed, the thermostat will display the above information from linked wireless devices and the
current readings from any wired sensors.
Press the ACCSRY button to exit accessory linking or viewing and return to the main screen.
A compatible wireless device must be linked to a thermostat with an RF Module installed for proper communication and
operation.
S1-LXRFM
RF Module
Accessory
(ACCSRY)
Button
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and the receiver. 3. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.
Operation with non-approved equipment is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the
approval of the manufacturer could void the user’s authority to operate this equipment.
Patent Pending
FCC ID MUH-RFM
P/N 88-811
Rev. 3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Create Date                     : D:20090727210049
Modify Date                     : D:20090727210049
Producer                        : Corel PDF Engine Version 3.0.0.739
Author                          : Mike McLaury
Creator                         : CorelDRAW
Title                           : S1-LXRFM Thermostat RF Module Owner's Manual Rev. 3

EXIF Metadata provided by EXIF.tools