Venture Global SSX-201 Wireless Sound Sensor Transmitter User Manual 2

Download:
Mirror Download [FCC.gov]
Document ID	3336712
Application ID	FIVJylvChOw6MWpbxm2y9w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	36.86kB (460809 bits)
Date Submitted	2017-03-29 00:00:00
Date Available	2017-03-29 00:00:00
Creation Date	2017-03-01 14:24:58
Producing Software	Corel PDF Engine Version 16.1.0.843
Document Lastmod	2017-03-01 14:27:29
Document Title	無標題-2
Document Creator	CorelDRAW X6
Document Author:	wwliu

ON/off button
ON/OFF button
Sensitivity
Microphone
Power On/OFF
Battery Installation
Insert 2 AAA battery compartment
Turn ON and turn OFF
This device has two ways to turn power on and off.
Hardware ON/OFF Slide the switch to ON or OFF
position.
If the slide switch is OFF, you cannot use the
software switch to turn on the power. If the unit is
not in use for a long period, use the hardware
switch to turn off the unit
Hardware switch
Software ON/OFF This allows the transmitter to
be controlled externally.
Off: If the sensor is ON, press and hold the
software ON/OFF switch 5 seconds, the LED will
flash.
ON: If the sensor is OFF, press and hold the
software ON/OFF switch 5 seconds, the LED will
Software switch
flash.
The sound sensor defaults to "ON" when the
hardware switch is moved from OFF to ON.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Note: Modifications to this product will void the user's authority to
operate this equipment.
Code Matching & Melody Selection
The sound sensor works with the receiver (chime) and must be
paired prior to use.
Step 1: Insert batteries in the sensor to be used.
Step 2: Insert batteries in the receiver to be
used.
ID
Step 3: Enter pairing mode for receiver
(chime unit). Press and hold the
learning button
3 seconds.
The LED #1 will flash.
Step 4: Press the button again to move to
the zone you want to pair with.
Learning
Press melody selector to scroll through button
the melodies. Once you hear your
Melody
selector
preferred melody, do not press again as
it is now selected.
There are 18 melodies & sound effects in
sequence.
Step 5: Switch on the sensor and speak into the microphone, the
red LED indicator will light. If successful, the receiver will
generate a short tone.
Press the button to exit pairing mode, the system is ready
to use
CHIME
Battery
compartment
LIGHT & CHIME
SSX-201
LIGHT
USER MANUAL
Operation
1.Open the cover. 2. Slide the power to the ON position,
3.Select the desired sensitivity low, mid, or high, this sets the level
of sound required to trigger the transmitter.
4.Stick the microphone to the device you want to detect.
Code Conflict
If the sound sensor coding and another transmitter is the same.
you must change the code of the sound sensor.
Open the cover
Slide the on/off switch
to OFF position
While pressing the test button
Slide the on/off switch to 'on'
position and hold the button 5
seconds. The LED will flash 5 times
when a new code is generated
When you have changed the code of the sound sensor you will then
need to re- pair the sound sensor with the receiver.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
T Y P E . D I S P O S E O F U S E D B AT T E R I E S A C C O R D I N G TO T H E
INSTRUCTIONS

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : wwliu
Title                           : 無標題-2
Create Date                     : 2017:03:01 14:24:58+08:00
Creator Tool                    : CorelDRAW X6
Modify Date                     : 2017:03:01 14:27:29+08:00
Metadata Date                   : 2017:03:01 14:27:29+08:00
Producer                        : Corel PDF Engine Version 16.1.0.843
Document ID                     : uuid:420f9891-5581-4ce1-968b-028c71943ea6
Instance ID                     : uuid:44a446aa-a14e-4503-8284-f630afff528d
Page Count                      : 1
Author                          : wwliu

EXIF Metadata provided by EXIF.tools