ViaSat VSC100 24GHz Satcom Road Speed Detector/Commercial Vehicles User Manual
ViaSat, Inc. 24GHz Satcom Road Speed Detector/Commercial Vehicles Users Manual
ViaSat >
Users Manual
VELOCITY SENSING CONTROLLER MODEL 100 (VSC100) OWNER’S MANUAL ViaSat - Digital Communication Products and Services for Commercial and Government Markets -1- ViaSat, Incorporated Advanced Microwave Products 1388 North Tech Blvd. Gilbert, AZ 8533 Office: +1 480-503-5505 Fax: +1 480-503-5501 ViaSat, Inc. Headquarters 6155 El Camino Real Carlsbad, CA 92009 Copyright 2014 © ViaSat, Inc. All rights reserved. No part of this work may be reproduced, published, or distributed in any form or by any means (electronically, mechanically, photocopying, recording, or otherwise), or stored in a database retrieval system, without the prior written permission of ViaSat Incorporated in each instance. -2- Table of Contents TABLE OF CONTENTS ............................................................................................................................. 3 DOCUMENT REVISION HISTORY ........................................................................................................ 3 INTRODUCTION ................................................................................................................................ 4 PRECAUTIONS ................................................................................................................................... 4 PRODUCT DESCRIPTION ................................................................................................................ 4 INSTALLATION ................................................................................................................................. 5 CONNECTOR ...................................................................................................................................... 6 Document Revision History Version Date Author 001 12/23/13 D. Saunders Contributors Change Tracker Description Initial Release Status: (click appropriate checkbox) Initial Draft Working Draft Pilot Released Revision to Released -3- Document No: 1183141 Version: 001 Date: 12/23/13 1 Introduction These instructions provide important information to the users of the ViaSat Velocity Sensing Controller Model 100, or VSC100. By following these instructions, the VSC100 will function properly over its lifetime. If these instructions are not followed, the VSC100 may malfunction and/or have a limited lifetime. 2 Precautions All installation, adjustment, or removal of the VSC100 should be undertaken by trained personnel who are trained in safety regulations for the system. This device complies with Part 15 of the FCC rules and carries the FCC ID is 2ABLPVSC100. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any unauthorized changes or modifications to the VSC100 could void the user’s authority to operate the equipment in the system. 3 Product Description The VSC100 includes an environmentally protective metal housing and plastic cover with wire harness as shown in Figure 1. Figure 1 – VSC100 -4- The VSC works using the Doppler principal. The sensor is pointed toward a road surface and transmits energy, some of which is scattered back to the VSC and received. If there is motion of the VSC with respect to the scatterers on the road surface, the received frequency will be offset from the transmitted frequency directly proportional to the velocity of the relative motion. As shown in Figure 2, the received frequency for motion "away" from the scatterers causes a decrease in frequency, while motion "toward" the scatterers causes an increase in frequency. The VSC100 measurement of frequency also depends on the installation angle with respect to the horizon, so care must be taken to ensure proper installation. Tx Rx Rx Motion Se ad ns ar or Frequency Motion Road Surface Figure 2 – Velocity Sensing Using Doppler 4 Installation The VSC100 typically mounts 1 meter above the ground on a bracket firmly attached to the under structure of the vehicle. It is oriented so that the plastic cover is pointing towards the rear of the vehicle at an angle of 30 degrees with respect to horizontal with the cable harness tied so that it does not obstruct the path from the VSC100 to the ground, as shown below in Figure 3. -5- Figure 3 – VSC100 Mounting 5 Connector The VSC100 connector is shown below in Figure 4. Figure 4 – VSC100 Connector When used in a system, the VSC100 is connected to a 12 volt power system, an indicator light, and two electromechanical latches. The wiring diagram is shown below in Figure 5. -6- Figure 5 – Wiring Harness -7-
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 7 Producer : GPL Ghostscript 8.15 Create Date : 2014:01:02 09:03:24 Modify Date : 2014:01:02 09:03:24 Title : Microsoft Word - Velocity Sensing Controller Owners Manual v001.doc Creator : PScript5.dll Version 5.2.2 Author : dsaundersEXIF Metadata provided by EXIF.tools