Viavi Solutions TBMTS5800V2 Multirate Handheld Telecommunications Tester (Ethernet, SONET, PDH) User Manual

Viavi Solutions Inc. Multirate Handheld Telecommunications Tester (Ethernet, SONET, PDH)

Contents

User Manual

Network and Service Enablement
One Milestone Center Court
Germantown, Maryland 20876-7100 USA
Toll Free 1-855-ASK-JDSU • Tel +1-301-353-1560 • Fax +1-240-404-1996
www.jdsu.com
T-BERD ⁄ MTS 8000, 6000A, and 5800
Multiple Services Application Module, 40/100G
Transport Module, Dual Module Carrier, and Handheld
Network Test Family
Getting Started Manual
MSAM, 40/100G Transport Module, DMC, and 5800 Getting Started Manual
ii 2204561, Rev. 000 January 2014
Notice
Every effort was made to ensure that the information in this document was accurate at the time of
printing. However, information is subject to change without notice, and JDS Uniphase reserves the
right to provide an addendum to this document with information not available at the time that this
document was created.
Copyright
© Copyright 2014 JDS Uniphase Corporation. All rights reserved. JDSU, Network and Service
Enablement, and the JDSU logo are trademarks of JDS Uniphase Corporation (“JDS Uniphase”).
All other trademarks and registered trademarks are the property of their respective owners. No part
of this manual may be reproduced or transmitted electronically or otherwise without written permis-
sion of the publisher.
Copyright release
Reproduction and distribution of this guide is authorized for Government purposes only.
Trademarks
JDSU Uniphase, JDSU, MTS 8000, T-BERD 8000, MTS 6000A, T-BERD 6000A, MTS 5800 and
T-BERD 5800 are trademarks or registered trademarks of JDS Uniphase in the United States and/
or other countries.
Bluetooth is a registered trademark of The Bluetooth SIG, Inc. in the United States and/or other
countries.
Specifications, terms, and conditions are subject to change without notice. All trademarks and
registered trademarks are the property of their respective companies.
Ordering information
The catalog number for a printed getting started manual is ML-22046563. The catalog number for
electronic manuals on USB is EML-22046537.
Terms and conditions
Specifications, terms, and conditions are subject to change without notice. The provision of hard-
ware, services, and/or software are subject to JDSU’s standard terms and conditions, available at
www.jdsu.com/terms.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case, the user will be required to correct the interference at this own expense. However, there is no
guarantee that interference will not occur in a particular installation.
MSAM, 40/100G Transport Module, DMC, and 5800 Getting Started Manual
January 2014 2204561, Rev. 000 iii
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two con-
ditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with the limits of a Class A digital device JDSU requires that quality
interface cables be used when connecting to this equipment. Any changes or modifications not
expressly approved by JDSU could void the user's authority to operate the equipment.
Industry Canada Requirements
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélec-
trique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
WEEE and Battery Directive Compliance
JDSU has established processes in compliance with the Waste Electrical and Electronic Equipment
(WEEE) Directive, 2002/96/EC, and the Battery Directive, 2006/66/EC.
This product, and the batteries used to power the product, should not be disposed of as unsorted
municipal waste and should be collected separately and disposed of according to your national
regulations. In the European Union, all equipment and batteries purchased from JDSU after 2005-
08-13 can be returned for disposal at the end of its useful life. JDSU will ensure that all waste equip-
ment and batteries returned are reused, recycled, or disposed of in an environmentally friendly
manner, and in compliance with all applicable national and international waste legislation.
It is the responsibility of the equipment owner to return equipment and batteries to JDSU for appro-
priate disposal. If the equipment or battery was imported by a reseller whose name or logo is
marked on the equipment or battery, then the owner should return the equipment or battery directly
to the reseller.
Instructions for returning waste equipment and batteries to JDSU can be found in the Environmental
section of JDSU’s web site at www.jdsu.com. If you have questions concerning disposal of your
equipment or batteries, contact JDSU’s WEEE Program Management team at
WEEE.EMEA@jdsu.com.
MSAM, 40/100G Transport Module, DMC, and 5800 Getting Started Manual
iv 2204561, Rev. 000 January 2014

Navigation menu