Vidonn Information Technology F1 Wireless Bone Conduction Headphones User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3550512
Application ID	2l7kGpNhnXVOAV5IfYtSOA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	29.07kB (363359 bits)
Date Submitted	2017-09-08 00:00:00
Date Available	2017-09-08 00:00:00
Creation Date	2017-09-08 09:57:12
Producing Software	Microsoft? Office Word 2007
Document Lastmod	2017-09-08 09:57:12
Document Title	User manual
Document Creator	Microsoft? Office Word 2007
Document Author:	paulwang

Vidonn F1 Manual
Home：
VIDONN F1
Wireless bone conduction sport headphone
User guide
Settings：
1. Charge
Charge the headphones with the included MicroUSB charging cable. The LED indicator will
turn blue from red when charging is complete.
2. Pair
While off, press and hold the power button for 5 seconds to enter pairing mode, the LED
indicator will flash blue and red repeatedly while in discovery.
3. Connect
In pairing mode, enable the Bluetooth settings in your device and select “Vidonn F1”,
VidonnF1 will be connected with in seconds and there is a voice prompt by the word
“connected”.
Multifunction Button
Function
Action
Prompt voice
Play/pause music
Click once
None
Skip to next song
Double-click while music is
playing
None
Answer/end call
Click once
One beep
Reject a call
Press and hold for 3 seconds
One beep
Low power alert
（Less than 30%）
Restore to factory settings
Battery low
Press and hold both volume
down button and
multifunction button
Two beeps
Volume Up/Power Button(B) Volume Down Button(C)
Function
Action
Prompt voice
Power on/ff
Press and hold power button
for 3 seconds
Power on/Power off
Turn up the volume
Click the volume up button to
adjust volume
There is one beep if reach
maximum
Enter into pairing mode
Press and hold the volume up
button until the LED flashes
red and blue alternately
Pairing
Turn down the volume
Click the volume down button
to adjust volume
There is one beep if reach
minimum
LED indicator
Status
LED display status
Charging
Solid red
Charging complete
Solid blue
Power on
Flash blue once
Power off
Flash red once
Pairing mode
Flash red and blue
Pairing complete
flash blue slowly
Unpaired
Flash red slowly
Playing music
Breathing blue
Incoming call
Solid blue
Low battery
Flash red slowly
How to reset your headphones
Enter pairing mode, then press multifunction button and both volume up button
simultaneously for 3 seconds.
Storage and maintenance
◆ Storage the headphones in cool and dry place, the working temperature should be 0-45℃
（32-113℉）. Working in cold/hot environment or highly humid area may reduce the life of
battery.
◆ After storage for a long time period, please charge the headphones before using again.
◆ The headphones are water resistant, but are NOT waterproof, please DO NOT submerse
the headphone in water.
◆ Listening with headphones at high volume may affect your hearing and the audio will be
distorted.
◆ Clean the headphone with a soft and dry cloth.
◆ Do not charge right after exercising, in case there is sweat inside the charging port, which
could lead to circuit burning while charging, keep the charging port dry before connecting
to charger will reduce the risk.
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void
your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.
Shenzhen Vidonn Information Technology Co., Ltd.
Address: 7F China Economy & Trade Building, 18 Zizhu 7 Road, Futian, Shenzhen, 518040 China
Customer service：400 065 8805
Email：info@vidonn.com
www.vidonn.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
Language                        : zh-CN
Author                          : paulwang
Creator                         : Microsoft? Office Word 2007
Create Date                     : 2017:09:08 09:57:12+08:00
Modify Date                     : 2017:09:08 09:57:12+08:00
Producer                        : Microsoft? Office Word 2007

EXIF Metadata provided by EXIF.tools