Vieworks FXRS03A System Control Unit User Manual

Vieworks Co., Ltd. System Control Unit

UserManual.wiki >

Vieworks >

FXRS03A User Manual >

User Manual

Wireless Service Manual Page 2 of 124 RA14-11A-022 Revision History Revision Date Descriptions 1.0 2012-06-08 Initial Release

Wireless Service Manual Page 3 of 124 RA14-11A-022 Contents Safety and Regulatory ....................................................................................................... 6 Safety Notice ............................................................................................................................................. 6 Safety Information .................................................................................................................................... 7 Battery Pack and Battery Charger Safety Information ......................................................................... 9 General Hazards ...................................................................................................................................... 11 Owner’s Responsibility ........................................................................................................................... 11 Notes for Using the Equipment ............................................................................................................. 12 Regulatory ............................................................................................................................................... 15 Medical Equipment Classifications .................................................................................................... 15 Equipment Standards ........................................................................................................................ 15 Guidance and Manufacturer’s Declaration for EMC Directive .......................................................... 16 Label and Symbols ............................................................................................................................ 19 1. Overview .................................................................................................................... 22 1.1 Features ........................................................................................................................................ 22 1.2 Intended Use ................................................................................................................................ 22 1.3 Standard Configuration ............................................................................................................... 23 2. Product Description .................................................................................................. 24 2.1 Product Components .................................................................................................................. 24 2.2 Detector ........................................................................................................................................ 26 2.2.1 Detector Specifications ........................................................................................................... 26 2.2.2 Detector Components ............................................................................................................ 27 2.2.3 Detector Dimension ................................................................................................................ 28 2.3 System Control Unit .................................................................................................................... 29 2.3.1 System Control Unit Specifications ........................................................................................ 29 2.3.2 System Control Unit Components .......................................................................................... 30 2.3.3 SCU Dimension ...................................................................................................................... 32 2.3.4 Fuse ........................................................................................................................................ 33 2.4 Battery Charger and Battery Pack ............................................................................................. 34 2.4.1 Battery Charger Specifications ............................................................................................... 34 2.4.2 Battery Charger Components ................................................................................................. 34 2.4.3 Battery Charger Dimension .................................................................................................... 35 2.5 Battery Pack ................................................................................................................................. 36 2.5.1 Battery Pack Specifications .................................................................................................... 36 2.5.2 Battery Pack Dimension ......................................................................................................... 36 2.5.3 Charging Battery Pack ........................................................................................................... 37

Wireless Service Manual Page 4 of 124 RA14-11A-022 2.6 X-ray Generator Interface ........................................................................................................... 38 2.6.1 X-ray Exposure Mode ............................................................................................................. 38 2.6.2 Timing of Signals (DR Trigger Mode) ..................................................................................... 40 2.6.3 EXT_INF Port Pin Assignment ............................................................................................... 40 2.6.4 Input and Output Circuits ........................................................................................................ 43 3. Packaging and Contents ........................................................................................... 44 4. How to Install ............................................................................................................. 45 4.1 Hardware Installation .................................................................................................................. 45 4.1.1 FXRD-1417WA (B) ................................................................................................................. 45 4.2 Software Installation .................................................................................................................... 49 4.2.1 Intel Gigabit Controller Driver Installation and Setting ........................................................... 49 4.2.2 Gigabit Controller Setting on Windows XP ............................................................................. 53 4.2.3 Gigabit Controller Setting on Windows 7 ............................................................................... 59 4.2.4 VXvue Installation ................................................................................................................... 64 4.2.5 Allowing VXvue to communicate through Windows Firewall on Windows XP ....................... 72 4.2.6 Allowing VXvue to communicate through Windows Firewall on Windows 7 .......................... 75 5. Prerequisite for Operation ........................................................................................ 77 5.1 Preparing the SCU ....................................................................................................................... 77 5.2 Generator Configuration ............................................................................................................. 78 5.3 Detector Configuration ............................................................................................................... 79 5.3.1 Detector Setting ...................................................................................................................... 80 5.3.2 Configuring Devices ............................................................................................................... 82 5.4 Detector Calibration .................................................................................................................... 87 5.4.1 Configuring the Detector ........................................................................................................ 87 5.4.2 Offset Calibration .................................................................................................................... 91 5.4.3 Defect Correction ................................................................................................................... 93 5.4.4 Gain Pixel Correction ........................................................................................................... 100 5.4.5 Detector Preference ............................................................................................................. 101 5.5 Diagnosis Mode ......................................................................................................................... 102 6. Operation ................................................................................................................. 104 7. Maintenance ............................................................................................................. 105 7.1 Function Test ............................................................................................................................. 105 7.2 Maintenance Guidelines for Users and Test Forms ............................................................... 106

Wireless Service Manual Page 5 of 124 RA14-11A-022 8. Troubleshooting ...................................................................................................... 122 8.1 Failure Case ............................................................................................................................... 122 8.1.1 Repairing SCU...................................................................................................................... 122 8.1.2 Repairing Power Failure ....................................................................................................... 122 8.1.3 Configuration Failure ............................................................................................................ 122 8.1.4 Repairing Communication Failure ........................................................................................ 122 9. Warranty ................................................................................................................... 123

Wireless Service Manual Page 6 of 124 RA14-11A-022 Safety and Regulatory Safety Notice The following safety notices are used to emphasize certain safety instructions. Follow the safety instructions in this manual along with warnings and cautions symbols. Ignoring such warnings or cautions while handling the product may results in serious injury or accident. It is important for you to read and understand the contents of this manual before attempting to use the product. Symbols Descriptions Indicates a potentially hazardous situation which will cause death, severe personal injury or substantial property damage if the instructions are ignored. Indicates a potentially hazardous situation which may cause minor personal injury or property damage if the instructions are ignored. Provides additional information that is helpful to you. It may emphasize certain information regarding special tools or items to check before operating the product.

Wireless Service Manual Page 7 of 124 RA14-11A-022 Safety Information This product is designed and manufactured to ensure maximum safety of operation and to meet all the safety requirements applicable to electronic medical equipment. However, anyone attempting to operate the system must be fully aware of potential safety hazards. It should be operated and maintained in strict compliance with the following safety precautions and operating instruments contained herein: Caution: Federal law restricts this device to sale by or on the order of a physician or a licensed practitioner. Always be alert when operating this device. If a malfunction occurs, do not use this device until qualified personnel correct the problems. The product should be installed, maintained and serviced according to Vieworks maintenance procedures and by Vieworks personnel or other qualified maintenance personnel approved in writing by Vieworks. Operation and maintenance should be done in strict compliance with the operation instructions contained in the manuals. The system, in whole or in part, cannot be modified in any way without written approval from Vieworks. Before authorizing any person to operate the system, verify that the person has read and fully understand the Service Manual. The owner should make certain that only properly trained and fully qualified personnel are authorized to operate the equipment. An authorized operators list should be maintained. Prevent unauthorized personnel from access to the system. It is important that this Service Manual be kept at hand, studied carefully and reviewed periodically by the authorized operators. The owner should ensure continuous power supply to the system, with voltage and current according to the product specifications. If power failures are frequent, an Uninterrupted Power Supply (UPS) should be installed to avoid loss of data. If the product does not operate properly or if it fails to respond to the controls described in this manual, the operator should immediately contact Vieworks field service representative. User must not contact a fuse holder or contacts of connector (ex: Inlet connector) with a patient simultaneously during operating the equipment and not allow patient to touch the fuse holder or contacts of connector.

Wireless Service Manual Page 8 of 124 RA14-11A-022 The images and calculations provided by this system are intended to be used as tools for the competent user. They are explicitly not to be regarded as a sole incontrovertible basis for clinical diagnosis. Users are encouraged to study the literature and reach their own professional conclusions regarding the clinical utility of the system. The user should be aware of the product specifications and of the system’s accuracy and stability limitations. These limitations must be considered before making any decision based on quantitative values, in case of doubt, please consult a Vieworks representative. Do not install the equipment in a location with the conditions listed below. Otherwise, it may result in failure or malfunction, fall or cause fire or injury.  Close to facilities where water is used.  Locations exposed to direct sunlight.  Close to air-conditioner or ventilation equipment.  Close to heat source such as a heater.  Prone to vibration.  Insecure place.  Dusty environment.  Saline or sulfurous environment.  High humidity.  Ambient temperature is higher than the operating temperature stated in this Service Manual. Occasionally, this product may have defect pixels caused by TFT characteristics. When the defect pixels are found, perform the Defect detection. For details about how to correct defect pixels, refer to 5.4.3 Defect Correction. Do not inflict excessive shock and mechanical vibration. Otherwise, it may result in poor image quality caused by noise. Do not unscrew or loosen the screws on the detector surface since all the screws are secured properly at the time of shipment. Otherwise, it may result in poor image quality or damage to equipment. This product may malfunction due to electromagnetic interference (EMI) caused by telecommunication devices, transceivers, electronic devices, etc. To prevent the electromagnetic wave from badly influencing the product, be sure to avoid placing it in close proximity to the product. Or, change direction or position of the product or move into the shielded place to reduce electromagnetic interference. To reduce the risk of electric shock, do not remove cover. No user-serviceable part inside. Refer servicing to qualified service personnel.

Wireless Service Manual Page 9 of 124 RA14-11A-022 Battery Pack and Battery Charger Safety Information Before using the battery pack and battery charger dedicated to ViVIX-S Wireless, read all applicable warnings and cautions. Not following these instructions could result in electrical shock, fire, explosion or other conditions which may cause death, injury or property damages. Do not use the battery pack as a power source for equipment other than ViVIX-S Wireless detectors. Be sure to use only the dedicated battery pack for the ViVIX-S Wireless detector. The battery charger is designed for the dedicated battery pack. Do not use the battery charger other than the dedicated one. Otherwise, a battery explosion or a battery leak may occur, resulting in fire or electrical shock. Do not operate the battery charger using any type of power supply other than the one indicated on the rating label. Do not handle the product with wet hands. Do not place heavy objects such as medical equipment on cables and cords, or do not pull, bend, bundle, or step on them to prevent their sheath from being damaged. Do not attempt to disassemble, alter, or apply heat to the product. Avoid dropping or subjecting the product to severe impacts. To avoid the risk of injury, do not touch the internal parts of the battery if it has been cracked or otherwise damaged. Stop using the battery pack immediately if it emits smoke, a strange smell, or otherwise behaves abnormally. Do not let the battery pack and battery charger come into contact with water or other liquids and do not allow them to get wet. Do not clean with substances containing organic solvents such as alcohol, benzene, thinner, or other chemicals. Otherwise, fire or electrical shock may result.

Wireless Service Manual Page 10 of 124 RA14-11A-022 Do not allow dirt or metal objects (such as hair pins, clips, staples or keys) to contact the terminals. Otherwise, battery explosion or leakage of electrolyte may occur, resulting in fire, injury or pollution of surrounding area. If the battery leaks and the electrolytes come into contact with your eyes, mouth, skin or clothing, immediately wash it away with running water and seek medical attention. Do not leave, store, or place the product in a location near heat sources, or in a place subject to direct sunlight, high temperature, high humidity, excessive dust, or mechanical shock. Otherwise, battery leakage, overheating or damage to the product may occur, resulting in electrical shock, burns, injury or fire. Do not attempt to use a battery pack that has deteriorated. Using a battery pack that has exceeded its life cycle may lead to overheating, fire or explosion. The Lithium ion/polymer battery is recyclable. Battery slowly discharges even if not in use. The battery pack may have expired if it discharges immediately after being fully charged. You can purchase an optional battery pack to replace an exhausted one. The battery pack is a consumable item. If a fully charged battery is consumed quickly, use a new and fully charged battery pack. Be sure to charge the battery periodically (once a year) if it is not used for an extended period of time. The battery pack cannot be charged if it has been over discharged. Before discarding the battery pack, cover the terminals with adhesive tape or other insulators. Contact with other metal materials may cause fire or explosion.

Wireless Service Manual Page 11 of 124 RA14-11A-022 General Hazards Radiation Hazards This system can be connected to x-ray generating equipment. Be certain to follow the safety instructions and specifications for wearing proper lead apron when x-ray exposures are planned or possible. All personnel should wear protective equipment including dosimeters during all phases of installation, operation and maintenance of the system. Electric Shock Hazards To reduce the electric shock hazard, the system must be connected to an electrical ground. A three conductor AC power cable is supplied with this system to provide the proper electrical grounding. The power cable must be plugged into an UL-approved three-contact electrical outlet. Do not disassemble or modify the product as it may result in fire or electric shock. There are no operator serviceable parts or adjustments inside the systems. Only trained and qualified personnel should be permitted access to the internal parts of the system. Explosion Hazards Do not operate the equipment in the presence of flammable or explosive liquids, vapors or gases. Do not plug in or turn on the system where hazardous substances are detected. If flammable substances are detected after the system has been turned on, do not attempt to turn off the system or unplug it. Evacuate and ventilate the area before turning the system off. Implosion Hazards Do not hit or drop the equipment. The equipment may be damaged if it receives a strong jolt, which may result in fire or electric shock if the equipment is used without it being repaired. Owner’s Responsibility The owner is responsible for ensuring that anyone using the system reads and understands the Service Manual and other relevant literature, and fully understands them. Vieworks makes no representation, however, that the act of reading this manual renders the reader qualified to operate, test and calibrate the system. Do not use the system if unsafe conditions are known to exist. In case of hardware failure that could cause hazardous conditions (smoke, fire and etc), turn the power OFF and unplug the power cords of all sub-systems.

Wireless Service Manual Page 12 of 124 RA14-11A-022 Notes for Using the Equipment System Diagnostic The VXSetup software runs a system diagnostic. Run VXSetup software after installing the system and at least once a year. If an error occurs, report the detailed error information to Vieworks local dealer or distributor. The owner is responsible for ensuring that the system diagnostic is performed every year. Do not try to use the system if the system diagnostic is failed. Calibration To ensure optimal performance of the system, it is important to verify that the system is calibrated. The owner is responsible for ensuring that the system calibration is performed after the system installation is completed or the system is repaired. Do not try to use the system if system calibration is not performed. Distances measurements Distances measurements in millimeters are possible only after distance calibration has been performed using a reference object (refer to VXvue User Manual). The operator is responsible for performing distance calibration with a reference object and verifying the results of the distance calibration before taking any distance measurements on an image. Left/Right Marker The operator is responsible for the correct and clear marking on the left or right side of the image to eliminate possible errors. The software includes an option to mark the image with L (left) or R (right) indicator from acquisition phase through printing and archiving. If the operator chose, for any reason, not to use L/R markers, he must use an alternative way to eliminate any possible mistake.

Wireless Service Manual Page 13 of 124 RA14-11A-022 Image Backup To avoid missing images which might result in patient being exposed to additional doses of radiation, it is important to backup the images by filming or by using a CD or DVD option. This should be done as a routine operation for every patient. If the hard disk of your workstation is about to full, the operator should backup images and delete the images to make room on the hard disk for new patient. User Limitations The VXvue software has the technician mode which could only be operated with the inputting PASSWORD. The technician mode should be operated by the personnel who are qualified by Vieworks. Cleaning the System Use a dry cloth to clean surfaces of the system. Do not use detergents or organic solvents to clean the system. Strong detergent, and organic cleaners may damage the finish and cause structural weakening. Do not clean the system with turning the power on. Disposal Disposal of this product in an unlawful manner may have negative effects on health and on the environment. When disposing of this product, therefore, be absolutely sure to follow the procedure which is in conformity with the laws and regulations applicable in your area. The expected life span of ViVIX-S Wireless system is about 3 years. Overheating Do not block the ventilation ports of the detector to prevent overheating of the detector. Overheating can cause system malfunction and damages. Electrical fire  This equipment is not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide.  Conductive fluids that drain into the active circuit components of the system may cause short circuits that can result in electrical fire. Therefore, do not place fluids or food on any part of the system.  To avoid electric shocks and burns caused by use of the wrong type of fire extinguisher, make sure that the fire extinguisher at the site has been approved for use on electrical fires.

Wireless Service Manual Page 14 of 124 RA14-11A-022 Handling the Equipment The Equipment must be handled with care to avoid personal injury damage to the internal image sensor.  Do not put pressure on the detector locally since it will cause permanent damage to the internal image sensor.  Excessive weight on the equipment may damage the internal image sensor.  It is recommended to use the case, in case if a patient should be positioned to put pressure on the detector while acquiring images. Load Limit Specifications Uniform Load 150 ㎏ over the whole area of the detector surface Local Load 100 ㎏ on an area 40 ㎜ in diameter Pediatric Application  Every request should be reviewed by the pediatric radiologist prior to beginning the examination to insure correct study is being performed.  If the technologist notices an unusual request, they should contact the pediatric radiologist. An example should be from pediatric clinic where they order a Full Cervical, Thoracic, and Lumbar Spine series. The pediatric radiologist should contact ordering physician and decide which study is the best for this pediatric patient.  The technologist should use the proper technique for the patient’s size to decrease the radiation dose when the technologist acquires diagnostic images.  ALL Pediatric patients shall be shielded for their x-ray examinations, except for when the shield will obscure the region of interest, as in a pelvic or SI joint xray for trauma or arthritis, or when it is physically or clinically unreasonable to shield the patient. For routine Hip X-Rays, ALL male children shall have their scrotum shielded using the small gonadal shield, females may not be shielded as this would obscure the hips.  To minimize motion in infants and young children, swaddle the infant. Use distraction tools to improve cooperation and projectors with child-friendly themes, music, toys with flashing lights or music, child-friendly images on the ceiling or walls, singing, counting, and a parent reading and talking to the child through the console all can help reduce anxiety and comfort the child.  A Scoliosis series will consist of a single frontal standing view of the spine. No lateral view or supine view is needed, unless specifically asked for by the Orthopedist or Radiologist. If the female’s breasts can be shielded without obscuring the spine, breast shields should be used.

Wireless Service Manual Page 15 of 124 RA14-11A-022 Regulatory Medical Equipment Classifications Type of protection against electrical shock Class Ⅰ equipment Degree of protection against ingress of water IPXO Mode of operation Continuous operation Flammable anesthetics NOT suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. Equipment Standards IEC/EN/UL 60601-1 Medical electrical equipment CSA C22.2 No. 601.1 Part 1: General requirements for safety IEC/EN 60601-1-2 Medical electrical equipment Part 2: Electromagnetic compatibility–requirements and tests IEEE 802.11a/b/g/n Wireless Communications

Wireless Service Manual Page 16 of 124 RA14-11A-022 Guidance and Manufacturer’s Declaration for EMC Directive This device has been tested for EMI/EMC compliance, but interference can still occur in an electromagnetically noisy location. Attempt to maintain a suitable distance between electrical devices to prevent malfunction. Electromagnetic Emissions The Equipment Under Test (EUT) is intended for use in the electromagnetic environment specified below. The customer or user of the EUT should assure that it is used in such an environment. Immunity Test Compliance Electromagnetic Environment – Guidance RF Emissions CISPR 11 Group 1 The EUT uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment. RF Emissions CISPR 11 Class A The EUT is suitable for use in all establishments other than domestic and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes. Harmonic emissions IEC 61000-3-2 Class A Voltage fluctuations/ Flicker emissions IEC 61000-3-3 Complies

Wireless Service Manual Page 17 of 124 RA14-11A-022 Electromagnetic Immunity The EUT is intended for use in the electromagnetic environment specified below. The customer or user of the EUT should assure that it is used in such an environment. Immunity Test IEC 60601 Test Level Compliance Level Electromagnetic Environment – Guidance Electrostatic discharge (ESD) IEC 61000-4-2 ±6 ㎸ contact ±8 ㎸ air ±6 ㎸ contact ±8 ㎸ air Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%. Electrical fast transient/burst IEC 61000-4-4 ±2㎸ for power supply lines ± 1 ㎸ for input/output lines ±2㎸ for power supply lines ± 1 ㎸ for input/output lines Mains power quality should be that of a typical commercial or hospital environment. Surge IEC 61000-4-5 ±1 ㎸ differential mode ±2 ㎸ common mode ±1 ㎸ differential mode ±2 ㎸ common mode Mains power quality should be that of a typical commercial or hospital environment. Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11 <5% Uт (>95% dip in Uт) for 0.5 cycle. 40% Uт (60% dip in Uт) for 5 cycles. 70% Uт (30% dip in Uт) for 25 cycles. <5% Uт (<95% dip in Uт) for 5 sec. <5% Uт (>95% dip in Uт) for 0.5 cycle. 40% Uт (60% dip in Uт ) for 5 cycles. 70% Uт (30% dip in Uт) for 25 cycles. <5% Uт (<95% dip in Uт) for 5 sec. Mains power quality should be that of a typical commercial or hospital environment. If the user of the EUT image intensifier requires continued operation during power mains interruptions, it is recommended that the EUT image intensifier be powered from an uninterruptible power supply or a battery. Power frequency (50/60 ㎐) magnetic field IEC 61000-4-8 3 A/m 3 A/m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment. NOTE: Uт is the a.c. mains voltage prior to application of the test level.

Wireless Service Manual Page 18 of 124 RA14-11A-022 Immunity Test IEC 60601 Test Level Compliance Level Electromagnetic Environment – Guidance Conducted RF IEC 61000-4-6 Radiated RF IEC 61000-4-3 3 Vrms 150 ㎑ to 80 ㎒ 3 V/m 80 ㎒ to 2.5 ㎓ 3 Vrms 150 ㎑ to 80 ㎒ 3 V/m 80 ㎒ to 2.5 ㎓ Portable and mobile RF communications equipment should be used no closer to any part of the EUT, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Recommended separation distance Where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in meters (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site surveya, should be less than the compliance level in each frequency range.b Interference may occur in the vicinity of equipment marked with the following symbol: NOTE 1: At 80 ㎒ and 800 ㎒, the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the EUT is used exceeds the applicable RF compliance level above, the EUT should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the EUT. b Over the frequency range 150 ㎑ to 80 ㎒, field strengths should be less than [V1] V/m.

Wireless Service Manual Page 19 of 124 RA14-11A-022 Label and Symbols Detectors FXRD-1417WA FXRD-1417WB

Wireless Service Manual Page 20 of 124 RA14-11A-022 System Control Unit Battery Charger

Wireless Service Manual Page 21 of 124 RA14-11A-022 Symbols Symbol Description Direct Current Alternating Current Protective Earth (Ground) Equipotentiality Power Off Attention, consult accompanying documents Power On Medical Equipment With Respect to electric shock, fire, and mechanical hazards only In accordance with UL60601-1 and CAN/CSA C22.2 No. 601.1. This mark shows compliance of the equipment with Directive 93/42/EEC. Read and understand all instructions and warning labels in the product documentation before using the equipment. Keep manual for future reference.

Wireless Service Manual Page 22 of 124 RA14-11A-022 1. Overview The ViVIX-S Wireless is advanced wireless flat panel X-ray imaging system designed for digital radiography. The lightweight wireless digital radiography is designed to be compatible with conventional X-ray film cassettes so that the users who are not familiar with Digital Radiography (DR) can easily understand and use the ViVIX-S system. In addition, the wireless communication (IEEE 802.11a/b/g/n) feature improves the operability and high-speed processing. 1.1 Features  Wireless LAN communication (IEEE 802.11a/b/g/n) feature  Supporting Conventional 35 × 43 X-ray film cassette  Compatible with not only new X-ray generators based on DR interface but also conventional X-ray generators  Designed with simple wiring and lightweight for portable applications  Image digitization, image inversion, image processing, zooming, panning, window level adjustment, contrast adjustment, and various features enable the operator to see diagnostic details that is difficult to see by using conventional non-digital techniques.  Depending on the operating environment, the Ether Con Cable (optional) enables the device to be used through expansion to a wired connection. 1.2 Intended Use The ViVIX-S Digital X-ray detector is indicated for digital imaging solution designed for providing general radiographic diagnosis of human anatomy. This device is intended to replace film or screen based radiographic systems in all general purpose diagnostic procedures. This device is not intended for mammography applications.

Wireless Service Manual Page 23 of 124 RA14-11A-022 1.3 Standard Configuration DetectorSystem Control UnitViVIX-S ViewerGigabit EthernetCables supplied with equipmentX-ray SystemGeneratorVieworksGenerator InterfaceTether InterfaceBattery Charger StandVieworksVieworksPlease~ Figure 1.1 ViVIX-S Wireless System Configuration Wireless communication is established between the ViVIX-S Wireless detector and System Control Unit. The ViVIX-S system is compliant with IEEE 802.11a/b/g/n (2.4 ㎓ / 5 ㎓). The available frequency band may vary depending on local radio laws and system requirements. Consult your local dealer for the frequency available in your area. Use of multiple WLAN devices within the same frequency band may interfere with each wireless communication and cause a decline in transmission speed. Do not cover or block the wireless module of the detector. Otherwise, the transmission speed or operable distance may be reduced. Recommended maximum operating distance of wireless communication between the detector and System Control Unit is 8 meters.

Wireless Service Manual Page 24 of 124 RA14-11A-022 2. Product Description ViVIX-S Wireless system consists of detector, system control unit (SCU), battery charger, battery pack, software and its accessories. 2.1 Product Components Detector  FXRD-1417WA (scintillator: CsI (TI))  FXRD-1417WB (scintillator: Gadox) System Control Unit (SCU)  FXRS-03A Battery Charger and Battery Pack  FXRC-01A  FXRB-01A Software  Viewer: VXvue  Calibration and Diagnostic: VXSetup

Wireless Service Manual Page 25 of 124 RA14-11A-022 Accessories (Cables)  AC Power Cable (2M)  Generator Interface Cable (15M)  Direct LAN Cable 15M (1000BASE-T)  Tether Interface Cable (3M) The use of accessories and cables other than those specified, with the exception of ViVIX-S Wireless accessories and cables sold by Vieworks Co., LTD. as replacement parts for internal components, may result in increased emissions or decreased immunity of the equipment. Accessory equipment connected to the analog and digital interfaces must be certified according to the respective IEC standards. All combinations of equipment must be in compliance with IEC 60601-1-1 system requirements. Any person who connects additional equipment to the signal input or signal output ports configures a medical system, and is therefore responsible for ensuring that the system complies with the requirements of the system standard IEC 60601-1. If in doubt, consult Vieworks technical support representative. Workstation (Recommended but NOT included)  Operating System Microsoft Windows XP 32 bit SP3 (Professional Edition), Windows 7 32 bit SP1 (Professional Edition or higher) or Windows 7 64 bit SP1 (Professional Edition or higher)  CPU Intel Core i5 2600 or higher (or equivalent AMD chips)  Memory 2 GB or higher  Hard Disk 1 TB or higher  Ethernet (NIC) Intel® PRO 1000 Series (PT, CT, etc) Min. Requirements: 1Gbps, Jumbo Frames - 9K, Receive Descriptors - 2K  Monitor 1280 × 800 or higher  CD-Rom CD or DVD R/W or blu-ray

Wireless Service Manual Page 26 of 124 RA14-11A-022 2.2 Detector 2.2.1 Detector Specifications Item Description Model FXRD-1417WA(B) Purpose General radiography Image Matrix Size 2560 × 3072 pixels Pixel Pitch 140 ㎛ Effective Imaging Area 358 ㎜ × 430 ㎜ Grayscale 14 bit, 16,384 grayscale Scintillator CsI (Cesium Iodide) or Gadox (Gadolinium Oxysulfide) Image Acquire and Transfer Time Preview: 2 s, Image Processing: 6.5 s (2 s when using Tether Interface) Spatial Resolution Min. 3.5 line pair/㎜ Rated Power Supply  Wireless  Wired DC +24 V, Max. 0.5 A  Powered by the battery pack (4,000 ㎃h)  Powered by the SCU using tether interface Power Consumption Max. 12 W Wireless Communications IEEE 802.11a/b/g/n (2.4 ㎓ / 5 ㎓) †Tether Interface (Optional) Gigabit Ethernet (1000BASE-T) via ‡PoE Imaging Plate Carbon Fiber Plate Cooling Air cooling Dimensions (H × W × D) 384 ㎜ × 460 ㎜ × 15 ㎜ Weight 3.0 ㎏ (including battery pack) Environmental Requirements Operation Temperature: +10 ∼ +35℃ Humidity: 30 ∼ 85% (Non-Condensing) Atmospheric pressure: 70 ∼ 106 ㎪ Altitude: Maximum 2000 meters Storage and transportation Temperature: -15 ∼ +55℃ Humidity: 10 ∼ 90% (Non-Condensing) Atmospheric pressure: 50 ∼ 106 ㎪ Altitude: Maximum 2000 meters Table 2.1 Detector Specifications †Tether Interface: Allows the detector to communicate with SCU via Ethernet cabling when wireless communications is not available or higher speed data transfer is necessary. ‡PoE (Power over Ethernet): Delivers electrical power over LAN cabling to the networked device.

Wireless Service Manual Page 27 of 124 RA14-11A-022 2.2.2 Detector Components 21ABCD34 Figure 2.1 Detector Components No. Name Description 1 Status Indicators Power button A: Data LED, Indicates communication and transmission status. - Blue B: Active LED, Indicates the detector is ready to work. - Orange C: Power LED, Indicates power on/off status. - Green D: Power button, Press to power on or off the detector. 2 Wireless Module Transmits data with wireless communications (IEEE 802.11a/b/g/n). 3 Tether Interface Allows the detector to communicate with SCU via PoE cabling (Gigabit Ethernet 1000BASE-T) 4 Battery Pack Supplies electrical power to the detector while communicating wirelessly. Table 2.2 Detector Components Description

Wireless Service Manual Page 28 of 124 RA14-11A-022 2.2.3 Detector Dimension Figure 2.2 Detector Dimension

Wireless Service Manual Page 29 of 124 RA14-11A-022 2.3 System Control Unit 2.3.1 System Control Unit Specifications Item Description Model FXRS-03A Power Supply Input: AC100 to 240V, 50/60 ㎐, Max. 200VA Output: DC +24V 3.3A, 80W Cabling Ports Gigabit Ethernet Ports – 3EA Power over Ethernet Ports – 2EA (Only for FXRD-1417) Wireless Communications IEEE 802.11a/b/g/n (2.4 ㎓ / 5 ㎓) Dimensions (W × H × D) 300 ㎜ × 235.8 ㎜ × 58 ㎜, Antenna Height – 105 ㎜ Weight 2.5 ㎏ Environmental Requirements Operation Temperature: +10 ~ +35℃ Humidity: 30 ∼ 85% (Non-Condensing) Atmospheric pressure: 70 ∼ 106 ㎪ Altitude: Maximum 2000 meters Storage and transportation Temperature: -15 ~ +55℃ Humidity: 10 ∼ 90% (Non-Condensing) Atmospheric pressure: 50 ∼ 106 ㎪ Altitude: Maximum 2000 meters Table 2.3 System Control Unit Specifications

Wireless Service Manual Page 30 of 124 RA14-11A-022 2.3.2 System Control Unit Components 123 Figure 2.3 System Control Unit (Front) No. Name Description 1 Power Switch Turns on or off the SCU. 2 Fan Expels heated air inside of the SCU. 3 Antenna Assists communications between the detector and SCU. 4 Status LED Indicates status of SCU operation and connection.  Blinking Green: Startup in progress  Blue: Connected to Wi-Fi network Table 2.4 System Control Unit Components (Front)

Wireless Service Manual Page 31 of 124 RA14-11A-022 1234567 Figure 2.4 System Control Unit (Back) No. Name Description 1 EXT_INF  Provides connection to the X-ray generator. 2 Port 1  Provides Gigabit Ethernet (1000BASE – T) communication between the workstation and SCU.  Gigabit Ethernet (1000BASE – T) Port Port 2, Port 3  Provides communication between FXRD-1717 and SCU when configuring multiple detectors.  Gigabit Ethernet (1000BASE – T) Port 3 Status LED  Indicates Port 4 and Port 5 status (Green: 1Gbps, Orange: 100Mbps) 4 Port 4, Port 5  Connection interface to communicate with the detector and to supply electrical power to the detector (Only for FXRD-1417).  Power over Ethernet Port (1000BASE-T) 5 Power Supply  Connection interface to supply power to a FXRD-1717 detector.  Max. DC +24V/24W (×2 ports) 6 P.E  Provides connection to equipotential ground. 7 AC Input  Connect the power cable to the power socket.  100 ~ 240V, 50/60 ㎐, T2AL250V Fuse (2 EA) Table 2.5 System Control Unit Components (Back) P.E (Potential Equalization) of SCU is used to keep equipotential between SCU and an equipment to be used with ViVIX-S Wireless. To connect to P.E of equipment, use a ground cable.

Wireless Service Manual Page 32 of 124 RA14-11A-022 2.3.3 SCU Dimension Figure 2.5 SCU Dimension

Wireless Service Manual Page 33 of 124 RA14-11A-022 2.3.4 Fuse Two fuses are installed inside of SCU to prevent electrical accidents due to an error such as overcurrent occurred in the AC Input. Stop immediately using SCU when fuses break. Item Description Model Littlefuse® 218002 (2 EA) Type Time Lag Cartridge Fuse Amp Rating 2 A Voltage Rating 250 V Replacing Fuses  Turn off SCU and its peripheral equipment, and pull the plug out of the power socket before replacing fuses.  When fuses break, resolve the cause of overcurrent first, and then replace the fuses with extra fuses (optional items, one set of two) or equivalent rating fuses.  User must not contact a fuse holder with a patient simultaneously during operating the equipment and not allow patient to touch the fuse holder. 1. Pull the fuse holder out from its receptacle under AC Input on the back panel of SCU. 2. Check the fuse(s) and replace it if necessary, using the fuse type and rating specified above. 3. Push the fuse holder back.

Wireless Service Manual Page 34 of 124 RA14-11A-022 2.4 Battery Charger and Battery Pack 2.4.1 Battery Charger Specifications Item Description Model FXRC-01A Simultaneous Charging Battery Pack 3 EA Charging Time 2 hours Rated Power Supply DC +24V, 2.7 A Max. Dimension (W × H × D) 192.0 ㎜ × 167.5 ㎜ × 223.4 ㎜ Weight 1.2 ㎏ Table 2.6 Battery Charger Specifications 2.4.2 Battery Charger Components 1234 Figure 2.6 Battery Charger No. Name Description 1 Battery Compartment Insert the battery pack to charge. 2 Charging Indicator Indicates the charging status. (Orange: Charging, Green: Fully Charged) 3 Power Indicator Indicates the power on/off status. 4 DC Input Connect the DC adapter to supply electrical power to the battery charger. Table 2.7 Battery Charger Components

Wireless Service Manual Page 35 of 124 RA14-11A-022 2.4.3 Battery Charger Dimension Figure 2.7 Battery Charger Dimension

Wireless Service Manual Page 36 of 124 RA14-11A-022 2.5 Battery Pack 2.5.1 Battery Pack Specifications Item Description Model FXRB-01A Type Lithium Polymer Rated Power Supply Output: DC +7.4V Capacity 4000 ㎃h Number of Cell 2S1P (2 Series 1 Parallel) Dimension (W × H × D) 144.4 ㎜ × 143.4 ㎜ × 7.0 ㎜ Weight 220 g Table 2.8 Battery Pack Specifications Figure 2.8 Battery Pack 2.5.2 Battery Pack Dimension Figure 2.9 Battery Pack Dimension

Wireless Service Manual Page 37 of 124 RA14-11A-022 2.5.3 Charging Battery Pack The battery pack supplies power to the detector during wireless connection. Be sure to use only the dedicated battery pack and fully charge it before use. 1 Connect the power cable (adapter not included) to the DC Input port of the battery charger and the power cord to the power source to supply power. The power LED lights in green indicating the presence of direct current (DC) power. 2 Insert the battery pack into the battery charger. Charging starts automatically. The charge LED lights orange when the battery pack is being charged. After the battery pack is charged completely, the charge LED lights in green. 3 Gently pull the charged battery pack to remove from the battery charger. Securely plug the power cord into the power source. If contact failure occurs, or if dust or metal objects come into contact with the exposed metal prongs of the plug, fire or electrical shock may occur. Be sure to stop charging the battery pack when the charge LED lights in green beyond the specified charging time. Not doing so may result in battery pack overheating or smoking or in explosion or fire. You must use the power adaptor that is certified with IEC 60950 or IEC 60601-1. Three batteries can be charged at the same time. It takes approximately two hours to fully charge a battery pack. The required charging time may vary depending on the temperature and remaining battery level.

Wireless Service Manual Page 38 of 124 RA14-11A-022 2.6 X-ray Generator Interface 2.6.1 X-ray Exposure Mode Mode Description DR Trigger Mode 1 The detector receives EXP_REQ signal that X-ray generator is prepared to generate X-rays. 2 The detector prepares image acquiring and then responds EXP_OK signal to the X-ray generator. 3 The X-ray generator confirms EXP_OK signal and generates X-rays, then the detector performs image acquiring according to Image Acquisition Time and transmits the image data.  EXP_REQ (Generator → Detector), EXP_OK (Detector → Generator) AED Mode  The detector detects actual amount of X-rays without any connection to the X-ray generator, and then performs image acquiring according to Image Acquisition Time and transmits the image data.  No signal used (No need to connect Generator Interface Cable.) Table 2.9 Exposure Mode 2.6.1.1 DR Trigger Mode DetectorX-ray SystemGeneratorExposure RequestExposure OKGenerator Interface Cable Figure 2.10 DR Trigger Mode Configuration  DR Trigger is the most common and recommended exposure mode. User can achieve the best quality images with DR Trigger Mode.

Wireless Service Manual Page 39 of 124 RA14-11A-022 2.6.1.2 AED Mode DetectorX-ray SystemGenerator Figure 2.11 AED Configuration  AED is available for acquiring images without any connection to X-ray generator. Generator interface cable is not required.  Make sure to follow operating environmental requirements (Temp: +10℃ ~ +35℃).  If you use AED Mode out of operating environmental requirements, unwanted image can be acquired without X-ray image acquiring.  Do not hit or drop the equipment. Unwanted images may be acquired in the AED Mode if it receives strong jolt.  If you use a Grid under general imaging condition (Dose) or image a thick object in the AED Mode, the efficiency of X-ray transformation may be reduced about 0% ~ 2% compared to the DR Trigger Mode according to the thickness of the target.  If you image a thick object in the AED Mode with low X-ray tube voltage, an image may not be acquired or horizontal line noise may occur.

Wireless Service Manual Page 40 of 124 RA14-11A-022 2.6.2 Timing of Signals (DR Trigger Mode) AA’B B’EXP_OKEXP_REQImage Acquisition Time Figure 2.12 Timing of Exposure signal  Image Acquisition Time+  Exposure request signal A (EXP_REQ) should be applied first, then exposure respond signal B (EXP_OK).  Image Acquisition Time can be set from 40 ㎳ to 4,000 ㎳ with 1 ㎳ increment when default value is 500 ㎳. 2.6.3 EXT_INF Port Pin Assignment 5 115 1120 1630 26 Figure 2.13 EXT_INF port pin assignments

Wireless Service Manual Page 41 of 124 RA14-11A-022 No. Signal Name I/O Color Description 1 EXP_REQ+_A Input Red  Detector receives signal that X-ray generator is prepared to generate X-rays.  Contact Type – On: Closed, Off: Open  For the 1st DR Interface of Generator 2 EXP_REQ-_A Input Black Return signal from EXP_REQ+_A. 3 EXP_REQ_TTL_A Input Orange  Detector receives signal that X-ray generator is prepared to generate X-rays.  TTL (Voltage) Type – On: VCC, Off: GND  Current (5 ㎃ ~ 10 ㎃), Voltage (12 V ~ 24 V)  For the 1st DR Interface of Generator 4 EXP_REQ_GND_A Input Gray Return signal from EXP_REQ_TTL_A 5 EXP_OK_POWER_A Input Yellow  Power of TTL signal coming from X-ray generator  This is for the 1st DR Interface of Generator, but it can be shared with the 2nd DR Interface. 6 EXP_OK+_A Output Green  Detector responds to X-ray generator about X-ray generation.  The X-ray generator generates X-rays according to this signal and then the detector performs X-ray image acquiring.  For the 1st DR Interface of Generator 7 EXP_OK-_A Output Brown Return signal from EXP_OK+_A 8 EXP_OK+_B Output Blue Same as “EXP_OK+_A” for the 2nd DR Interface of Generator. 9 EXP_OK-_B Output Pink Same as “EXP_OK-_A” for the 2nd DR Interface of Generator. 10 Reserved - - Do not connect. Reserved for testing. 11 EXP_REQ+_B Input White Same as “EXP_REQ+_A” for the 2nd DR Interface of Generator. 12 EXP_REQ-_B Input Purple Same as “EXP_REQ-_A” for the 2nd DR Interface of Generator. 13 EXP_REQ_TTL_B Input White/Red Same as “EXP_REQ_TTL_A” for the 2nd DR Interface of Generator. 14 EXP_REQ_GND_B Input White/Black Same as “EXP_REQ_GND_A” for the 2nd DR Interface of Generator. 15 Reserved - - Do not connect. Reserved for testing. Table 2.10 EXT_INF1 port pin description (1 ~ 15)

Wireless Service Manual Page 42 of 124 RA14-11A-022 No. Signal Name I/O Color Description 16 EXP_REQ+_C Input Red Same as “EXP_ REQ+_A” for the 3rd DR Interface of Generator. 17 EXP_REQ-_C Input Black Same as “EXP_ REQ-_A” for the 3rd DR Interface of Generator. 18 EXP_REQ_TTL_C Input Orange Same as “EXP_REQ_TTL_A” for the 3rd DR Interface of Generator. 19 EXP_REQ_GND_C Input Gray Same as “EXP_REQ_GND_A” for the 3rd DR Interface of Generator. 20 EXP_OK_POWER_C Input Yellow Same as “EXP_OK_POWER _A” for the 3rd DR Interface of Generator. 21 EXP_OK+_C Output Green Same as “EXP_OK+_A” for the 3rd DR Interface of Generator. 22 EXP_OK-_C Output Brown Same as “EXP_OK-_A” for the 3rd DR Interface of Generator. 23 EXT_A+ Input -  Detector receives the 1st status signal that it is equipped on/in the table or in the wall stand.  Contact Type – On: Closed, Off: Open 24 EXT_A- Input - Return signal from EXT_A+ 25 EXT_B+ Input - Same as “EXT_A+” for the 2nd status signal 26 EXT_B- Input - Same as “EXT_A-” for the 2nd status signal 27 EXT_C+ Input - Same as “EXT_A+” for the 3rd status signal 28 EXT_C- Input - Same as “EXT_A-” for the 3rd status signal 29 EXT_D+ Input - Same as “EXT_A+” for the 4th status signal 30 EXT_D- Input - Same as “EXT_A-” for the 4th status signal Table 2.11 EXT_INF2 port pin description (16 ~ 30)

Wireless Service Manual Page 43 of 124 RA14-11A-022 2.6.4 Input and Output Circuits The following diagrams describe exposure request and exposure OK circuits. Figure 2.14 Exposure Request Input Circuit Figure 2.15 Exposure Respond Output Circuit

Wireless Service Manual Page 44 of 124 RA14-11A-022 3. Packaging and Contents Detector (FXRD-1417WA/B) System Control Unit (FXRS-03A) Battery Charger Battery Pack Generator Interface Cable (15M) LAN Cable (Gigabit LAN, 15M) AC Power Cable Tether Interface Installation Software CD Viewer: VXvue Calibration SW: VXSetup Calibration Data Table 3.1 ViVIX-S Wireless Packaging

Wireless Service Manual Page 45 of 124 RA14-11A-022 4. How to Install 4.1 Hardware Installation This section describes how to connect the flat panel imaging system (detector) whose model name is FXRD-1417WA(B). Installation of this equipment should be made by licensed and authorized personnel. 4.1.1 FXRD-1417WA (B) 1 Connect the one end of the generator interface cable to the EXT_INF port of SCU, and the other to the port of the X-ray generator. 2 Connect the one end of the LAN cable to Port 1 of SCU, and the other to the LAN Card Connector of workstation assigned for the Data Transfer.

Wireless Service Manual Page 46 of 124 RA14-11A-022 3 Make an antenna of SCU stand upright. 4 To transmit image data using Tether Interface, connect the one end of the Tether Interface cable to Port 4 or Port 5 of SCU.

Wireless Service Manual Page 47 of 124 RA14-11A-022 5 Connect the power cable to the AC port of the SCU to supply power. This equipment must only be connected to a supply mains with protective earth. 6 Turn on the power switch in front of the SCU.

Wireless Service Manual Page 48 of 124 RA14-11A-022 7 Attach a fully charged battery pack to the detector. To attach the battery pack, slide the battery pack into the battery compartment of the detector. Make sure that the claws on the battery pack are aligned with the groove on the battery compartment. Slide the battery lock lever until it clicks into place. 8 Press and hold the power button of the detector for 3 seconds to turn on the detector. 9 When you have finished using the detector, press and hold the power button for 3 seconds to turn off the detector. Remove the battery pack if the detector will not be used for some time. To remove the battery pack, slide the battery lock lever to release it, put your fingers on the battery compartment groove that lifts up, and then pull out the battery pack. When the detector is not be used for some time, remove the battery pack. Otherwise, over discharge may occur, resulting in shortened battery life.

Wireless Service Manual Page 49 of 124 RA14-11A-022 4.2 Software Installation 4.2.1 Intel Gigabit Controller Driver Installation and Setting Before installing Intel Gigabit Controller Driver, make sure your Ethernet Card is properly installed on the workstation. The recommended Ethernet Card is Intel® Gigabit CT or later. And also, Ethernet Card supporting 1 Gbps or above is available. Gigabit LAN card must support the following requirements. [Jumbo Frames: 9014 Byte], [Receive Descriptors: 2048] This is not a component of ViVIX-S but recommend component. So, you have to use installation package designed for your Gigabit Controller. 1~8 steps may differ according to Gigabit Controller to use. Following procedures are provided as an example to refer to. 1 Click PROXP.exe to start InstallShield Wizard, and then click the Run button.

Wireless Service Manual Page 50 of 124 RA14-11A-022 2 Click the Next button. 3 Accept the license agreement and click the Next button.

Wireless Service Manual Page 51 of 124 RA14-11A-022 4 Select the components to install and click the Next button. 5 Click the Install button.

Wireless Service Manual Page 52 of 124 RA14-11A-022 6 When the following message appears, click the Continue Anyway button. 7 Installation status bar appears in Installing Intel® Network Connections dialog box.

Wireless Service Manual Page 53 of 124 RA14-11A-022 8 Click the Finish button. 4.2.2 Gigabit Controller Setting on Windows XP 1 Click Start > Setting > Control Panel > Network Connections to open the Network Connections dialog box, and then rename Local Area Connection with GigE. It is not necessary to change name with GigE. It just distinguishes between that connection and other connections. 2 Right-click the GigE and then click the Properties.

Wireless Service Manual Page 54 of 124 RA14-11A-022 3 Uncheck all checkboxes except Vieworks Image Filter Driver or GigaLinx Image Filter Driver and Internet Protocol [TCP/IP]. 4 Click the Internet Protocol [TCP/IP] and set the IP as shown below, and then click the Advanced button.

Wireless Service Manual Page 55 of 124 RA14-11A-022 5 Click the OK button to close the dialog box. 6 Click Start > Setting > Control Panel > Network Connections to open the Network Connections dialog box, and right-click GigE, and then click Properties to open the GigE Properties dialog box. Click the Configure button to open the following dialog box, and then go to the Advanced tab.

Wireless Service Manual Page 56 of 124 RA14-11A-022 7 Set the Jumbo Frames to the maximum value. 8 Choose Performance Options in the list of Settings and click the Properties button on the right.

Wireless Service Manual Page 57 of 124 RA14-11A-022 9 Choose Flow Control in the list of Settings and Generate & Respond in the list of Value as shown below. 10 Choose Interrupt Moderation Rate in the list of Settings and Extreme in the list of Value as shown below.

Wireless Service Manual Page 58 of 124 RA14-11A-022 11 Choose Receive Descriptors and set to the maximum value. 12 Click the OK button.

Wireless Service Manual Page 59 of 124 RA14-11A-022 4.2.3 Gigabit Controller Setting on Windows 7 1 Click Start > Control Panel > Network and Internet > Network and Sharing Center > Change Adapter Setting and then rename Local Area Connection with GigE. It is not necessary to change name with GigE. It just distinguishes between that connection and other connections. 2 Right-click the GigE and then click the Properties.

Wireless Service Manual Page 60 of 124 RA14-11A-022 3 Uncheck all checkboxes except Vieworks Image Filter Driver or GigaLinx Image Filter Driver and Internet Protocol [TCP/IP]. 4 Click the Internet Protocol [TCP/IP] and set the IP as shown below, and then click the Advanced button.

Wireless Service Manual Page 61 of 124 RA14-11A-022 5 Click Start > Control Panel > Network and Internet > Network and Sharing Center > Change Adapter Setting, right-click GigE, and then click Properties to open the GigE Properties dialog box. Click the Configure button to open the following dialog box, and then go to the Advanced tab. 6 Set the Jumbo Packet to the maximum value.

Wireless Service Manual Page 62 of 124 RA14-11A-022 7 Choose Flow Control in the list of Property and select Rx & Tx Enabled in the list of Value as shown below. 8 Choose Interrupt Moderation Rate in the list of Property and Extreme in the list of Value as shown below.

Wireless Service Manual Page 63 of 124 RA14-11A-022 9 Choose Receive Buffers and set to the maximum value. 10 Click the OK button.

Wireless Service Manual Page 64 of 124 RA14-11A-022 4.2.4 VXvue Installation User must follow instructions below to protect against cyber security threats such as virus and worms.  Prior to installing and using VXvue, scan the computer system with anti-virus software to make sure the system is virus free.  Install, setup and enable adequate anti-virus software.  The operating system should be updated frequently to protect VXvue against harmful activities.  If you have a cyber security problem, contact the manufacturer on the phone or by e-mail referring to the contact information in this manual. 1 Insert the CD/DVD into the CD Drive. 2 Run Setup.exe. 3 Click the Yes button when the following dialog appears. The dialog may not appear depending on your Windows settings.

Wireless Service Manual Page 65 of 124 RA14-11A-022 4 The prerequisites for VXvue installation are displayed in the VXvue – InstallShield Wizard dialog, then click the Install button. The installation may take several minutes depending on your system environment. The items listed under the Requirement may from the above figure depending on your system environment.

Wireless Service Manual Page 66 of 124 RA14-11A-022 5 When the prerequisites for VXvue installation have been installed, click the Next button. 6 A driver for recognizing license hardware key will be installed on your system during setup process. If the window installing the driver appears, do not close the window and wait for the installation to complete.

$Wireless Service Manual Page 67 of 124 RA14-11A-022 7 Choose the application type and click the Next button. 8 Choose the folder location where you want to save VXvue data. The default destination is D:\Database. To change the folder location, click the Browse button to locate the folder.$

Wireless Service Manual Page 68 of 124 RA14-11A-022 9 Click the Install button to begin VXvue installation. 10 The installation process will continue and a progress bar will be displayed in the Setup Status window.

Wireless Service Manual Page 69 of 124 RA14-11A-022 11 When the installation is complete, click the Finish button. 12 When Filter Driver installation dialog appears after installing VXvue, choose BroadLinx Universal Filter Driver and click the Next button.

Wireless Service Manual Page 70 of 124 RA14-11A-022 13 Select the network interface card connected to SCU and click the Next button. The above figure may vary depending on your system environment. 14 The progress of Filter Driver installation will be displayed.

$Wireless Service Manual Page 71 of 124 RA14-11A-022 15 Click Install this driver software anyway when the following dialog appears. 16 After completing installation, click the Yes button to restart the computer. 17 Now the VXvue software and data are successfully installed in each directory as shown below.  Software: C:\program files\VXvue  Image and other data: D:\Database or user defined folder  Executable File - VXvue.exe: Image Viewer - VXSetup.exe: Calibration Software$

$Wireless Service Manual Page 72 of 124 RA14-11A-022 4.2.5 Allowing VXvue to communicate through Windows Firewall on Windows XP 1 Click Start > Setting > Control Panel > Windows Firewall and then click the Exceptions tab. 2 Click the Add Program… button. 3 Click the Browse button and locate C:\Program files\VXvue\VXvue.$

Wireless Service Manual Page 73 of 124 RA14-11A-022 4 Click the Open button. 5 Select the VXvue and then click the OK button.

Wireless Service Manual Page 74 of 124 RA14-11A-022 6 Check the VXvue to select and then click the OK button.

Wireless Service Manual Page 75 of 124 RA14-11A-022 4.2.6 Allowing VXvue to communicate through Windows Firewall on Windows 7 1 Click Start > Control Panel > Windows Firewall. 2 Click Allow a program or feature through Windows Firewall. 3 Click the Change settings button if it is enabled and then click the Allow another program button.

$Wireless Service Manual Page 76 of 124 RA14-11A-022 4 Click the Browse button and locate C:\Program files\VXvue\VXvue.exe. 5 Click the Open button. 6 Select the VXvue and then click the Add button. Add VXSetup (located in C:\Program files\VXvue\VXSetup.exe) in the same manner as described above.$

Vieworks FXRS03A System Control Unit User Manual

Vieworks Co., Ltd. System Control Unit

Contents

User Manual

Navigation menu

Namespaces

Views

Navigation