Vision Automobile Electronics Co ZR1202US Z-Wave Repeater User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2230066
Application ID	ZK1tWw7DRA/y9YaM+oL5uw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.45kB (105637 bits)
Date Submitted	2014-04-01 00:00:00
Date Available	2014-04-03 00:00:00
Creation Date	2013-11-20 15:48:55
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2013-11-20 15:48:55
Document Title	(Microsoft Word - _20131119\267s\252\251_ZR1202 Repeater.doc)
Document Creator	PScript5.dll Version 5.2
Document Author:	--

Federal Communications Commission Statement
This equipment has been followed with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try and correct the
interferene by one of the following measures:
Reorient or relocate the receiving antenna,
Increase the separation between the equipment and receiver,
Connect the equipment into and outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undersired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
Limited Warranty
Vision Guarantees that every wireless repeater is free from physical defects in material and
workmanship under normal usage for one year from the date of purchase. If the product
proves defective during this one-year warrany period, Vision will replace it free of charge.
Vision does not issue any refunds. This warnnty is extended to the original end user
purchase only and is not transferable. This warranty does not apply to : (1) damage to units
caused by accident, dropping or abuse in handling, or any negligent usage; (2) units which
have been repaired, taken apart, or modified by an unauthorized personnel; (3) units not
used in accordance with instruction; (4) damanges exceeding the cost of the produt; (5)
transit damage, initial installation costs, removal cost, or reinstallation cost.
For information on addional devices, plesae visit us at www.visionsecurity.com.tw
Installation & Operation Manual
ZR1202IN
ZR1202EU
ZR1202RU
ZR1202US
ZR1202IS
ZR1202JP
ZR1202BR
Z-Wave Repeater
ZR2102
V0
1021114
6B1Z-12001
Introduction
Thanks for choosing the Vision’s repeater of the home automation device. This
module is a Z-Wave™ enabled device (interoperable, two-way RF mesh
networking technology) and is fully compatible with any Z-Wave™ enabled
network. Every main powered Z-Wave enabled device acts as a signal repeater
and multiple devices result in more possible transmission routes which helps
eliminate “RF dead-sports”
Z-Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it
regardless of the manufacturer, and ours can also be used in other
manufacturer’s Z-Wave™ enabled networks. This device take existing Z-WAVE
signal, repeat and send it to a longer range where it is too far away for the
controller (supporting FLiRS devices).
*** For indoor use only ***
1. Fix the repeater under the vertical way as high as possible then insert the
suitable Micro USB Power Adaptor to the ZR1202 then it will go to the
Learning Mode automatically. (The LED will start flash which means the
repeater has not been “Include” yet.)
For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface
Controller into “exclusion” mode, and following its instruction to delete the
ZR1202 from your controller. Press the program switch on the ZR1202 once
to be excluded.
Note: LED setting light will flash continuously in Exclusion condition.
(2)
(1)
Micro USB Power Input
(1) Press
(2) Slide down to release the bracket
Specification:
Protocol: Z-Wave™ (ZM4101)
Frequency Range:
865.22MHz (ZR1202IN)
868.42MHz (ZR1202EU)
869.00MHz (ZR1202RU)
908.42MHz (ZR1202US)
916.00MHz (ZR1202IS)
920-928MHz(ZR1202JP)
921.42MHz (ZR1202BR)
Operating Range: Up to 200 meters
Operating Temp.: -15°C~ 60°C (5°F ~140°F)
Operating Voltage: 5V/DC
Current Consumption: 300mA (±50mA)
Installation
Notice: If you are installing the entire Z-Wave™ system for the first time, please
refer to the installation guide of Z-Wave™ Interface Controller before installing ZR
1202 Repeater Module.
2. For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface
Controller into“ inclusion” mode and following its instruction to add the
ZR1202 to your controller. To get in the “inclusion” mode, the distance
between module and controller is suggested to be in one meter. Press the
program switch on the ZR1202 once. The LED should stop flashing, if not,
please try again.
Product Description and Specification
Release the bracket:
※Note: Suitable adapter specification:
-Micro USB Power Input
-Operating Voltage: 5V/DC
-Current Consumption: 500m
Program Switch
Package Content:
1pc
ZR1202 Repeater module
1pc
ZR1202 Repeater Bracket
1pc
Adapter (Optional)
1pc
Installation & Operation Manual
3. Use “Power Level Set” command for setting the strength of RF during one
period.
4. Use “Power Level Test Node Set” command to test the direct signal for fixed
node.
5. Support Repeaters for routing (FLiRS included)
6. Support Explorer Frame function
7. Press Program Switch for 5 seconds, the ZR1202 will reset back to factory
default.
★ The ZR1202 operating range will be up to 200 meters under
the correct installation!!
Z-Wave™ Command Class:
COMMAND_CLASS_BASIC
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_VERSION
-1 -
-2 -

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2013:11:20 15:48:55
Modify Date                     : 2013:11:20 15:48:55
Title                           : (Microsoft Word - _20131119\267s\252\251_ZR1202 Repeater.doc)
Creator                         : PScript5.dll Version 5.2
Author                          : --

EXIF Metadata provided by EXIF.tools