Vision Fitness R1400 Users Manual R1415 Assy3
R1400 to the manual b4f5a461-5c5b-4744-aab8-cb221630f3d8
2015-02-05
: Vision-Fitness Vision-Fitness-R1400-Users-Manual-457008 vision-fitness-r1400-users-manual-457008 vision-fitness pdf
Open the PDF directly: View PDF 
.
Page Count: 3
| Download | |
| Open PDF In Browser | View PDF |
©2006 Vision Fitness. All Rights Reserved. 8.06 AG18.40PRD REV3 R1400 AND R1500 SEMI-RECUMBENT FITNESS BIKES www.visionfitness.com toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 Assembly Guide vision it all starts with a TOOLS & PARTS INCLUDED 17mm/15mm Pedal Wrench 5mm T-Shaped Wrench HARDWARE INCLUDED ORANGE BAG PINK BAG M8 x 15L Bolt Quantity: 3 SW8 Lock Washer Quantity: 2 R1500 Only M8 x 15L Bolt Quantity: 2 R1500 Only SW8 Lock Washer Quantity: 3 4mm L-Shaped Wrench Screwdriver BLUE BAG M8 x 20L Bolt Quantity: 2 R1500 Only Rubber Stopper Quantity: 1 M5 x 10L Bolt Quantity: 1 M8 x 15L Bolt Quantity: 4 Wire Grip Quantity: 1 SW8 Lock Washer Quantity: 2 R1500 Only GREEN BAG SW8 Lock Washer Quantity: 4 M8 x 15L Bolt Quantity: 4 SW8 Lock Washer Quantity: 4 BLACK BAG PARTS BOX Power Supply Water Bottle and Cage Color Coded Hardware Bags Assembly Guide Owners Manual Warranty Card M8 x 10L Set Screw Quantity:1 5mm L-Shaped Wrench M6 Arc Washer Quantity: 8 M6 x 35L Bolt Quantity: 8 SW8 Lock Washer Quantity: 4 M8 x 15L Bolt Quantity: 4 R1400 AND R1500 SEMI-RECUMBENT FITNESS BIKES ©2006 Vision Fitness. All Rights Reserved. 8.06 AG18.40PRD REV3 www.visionfitness.com toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 Assembly Guide vision it all starts with a TOOLS & PARTS INCLUDED HARDWARE INCLUDED 17mm/15mm Pedal Wrench 5mm T-Shaped Wrench ORANGE BAG PINK BAG SW8 Lock Washer Quantity: 2 R1500 Only M8 x 15L Bolt Quantity: 2 R1500 Only M8 x 15L Bolt Quantity: 3 SW8 Lock Washer Quantity: 3 M8 x 20L Bolt Quantity: 2 R1500 Only SW8 Lock Washer Quantity: 2 R1500 Only 4mm L-Shaped Wrench Screwdriver BLUE BAG Rubber Stopper Quantity: 1 M5 x 10L Bolt Quantity: 1 M8 x 15L Bolt Quantity: 4 Wire Grip Quantity: 1 SW8 Lock Washer Quantity: 4 GREEN BAG M8 x 15L Bolt Quantity: 4 SW8 Lock Washer Quantity: 4 BLACK BAG PARTS BOX Power Supply Water Bottle and Cage Color Coded Hardware Bags Assembly Guide Owners Manual Warranty Card M8 x 10L Set Screw Quantity:1 5mm L-Shaped Wrench M8 x 15L Bolt Quantity: 4 SW8 Lock Washer Quantity: 4 M6 x 35L Bolt Quantity: 8 M6 Arc Washer Quantity: 8 Assembly Guide STEP STEP STEP 6 5 STEP Handlebar R1400 AND R1500 SEMI-RECUMBENT FITNESS BIKES Water Bottle Cage 3 • Connect the heart rate wires coming from the seat rail to the heart rate wires coming from the main frame. 4 • As you slide the seat rail onto the seat rail bracket, slide any excess heart rate wire into the seat rail bracket. Slide the seat rail on so the holes on the bottom of the bracket are in line with the frame. Insert three (M8x15L) bolts with three (SW8) lock washers into the holes for support. Do not tighten completely. Console Mast Console Mast Cover To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here: Console Mast Bracket Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 PINK BAG • R1500 ONLY: Connect the bottom frame support tube to the bottom of the rear support foot with two (M8x20L) bolts and two (SW8) lock washers. Tighten with the 5mm T-handle wrench. Heart Rate Wires • Go back and tighten all bolts with the 5mm T-handle or 5mm L-shaped wrench. NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw. STEP STEP 1 ORANGE BAG • R1500 ONLY: Connect bottom frame support tube to main frame with two (M8x15L) bolts and two (SW8) lock washers. Tighten with the 5mm T-handle wrench. STEP 2 4 Bottom Frame Support Tube R1500 ONLY STEP • Wrap the wire tie that comes from the bottom of the console mast around the end of console cable and around the heart rate wires that are sitting in the frame console mast bracket. Slowly pull the wire tie up through the console mast until the cable and wires come through the top of the mast. Slide the bottom of the console mast over the frame mast bracket. Holding the mast straight, insert the (M8x10L) set screw into the front side of the mast and tighten with the 4mm L-shaped wrench. Secure the mast to the frame with four (M8x15L) bolts and four (SW8) lock washers on the sides of the mast and tighten with the 5mm T-handle wrench. 1 BLUE BAG • Attach rear support foot to the bottom of the seat rail with four (M8x15L) bolts and four (SW8) lock washers. Do not tighten completely. • Slide the seat frame onto the seat rail. Make sure the flat side of the clamp block rests against the bottom of the seat rail. Also make sure the adjustment handle is facing forward. • Attach the rubber stopper to the bottom of the seat rail with the (M5x10L) bolt. Tighten with the screwdriver. STEP 6 PEDALS • Remove the four bolts from the back side of the console. Plug the console cable and heart rate wires into the back side of the console. Place the console onto the mounting plate of the console mast and re-insert the four mounting bolts. Tighten with the screwdriver. Seat Frame • Insert the heart rate wires located under the seat frame through the hole on the bottom of the seat rail and push them toward the front of the rail. Take the end of the heart rate wires that run through the seat rail and insert them through the hole in the bracket at the end of the rail. Snap the wire grip around the end of the heart rate wires and snap it into place in the bracket. STEP 2 • Remove the two bolts from the backside of the console mast. Attach the water bottle cage to the mast with these two bolts. Tighten with the screwdriver. Insert water bottle. Seat Rail Seat Rail Bracket Rear Support Foot STEP Rubber Stopper STEP • Plug in power supply to power socket on the front side of the bike. 3 Heart Rate Wires Wire Grip • Attach left and right pedal straps to left and right pedals. • Attach left and right pedals to left and right crank arms. NOTE: both pedals and crank arms should be labeled left or right. Tighten with the included pedal wrench. GREEN BAG • Slide the console mast cover onto the console mast. Heart Rate Wires 5 BLACK BAG • Connect the Heart Rate wires from the seat handlebar to the heart rate wires from the seat frame. Attach seat handlebar to seat frame with four (M8x15L) bolts and four (SW8) lock washers. Tighten with 5mm T-shaped wrench. • Attach seat bottom cushion to seat frame with four (M6x35L) bolts and four (M6) arc washers. Tighten with the 4mm L-shaped wrench. • Attach the seat back cushion to the seat frame with four (M6x35L) bolts and four (M6) arc washers. Tighten with the 4mm L-shaped wrench.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 3 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:3299a302-46b1-11dd-8ab2-0017f205b280 Producer : Acrobat Distiller 6.0.1 for Macintosh Modify Date : 2008:06:30 09:31:16-05:00 Creator Tool : QuarkXPress: pictwpstops filter 1.0 Create Date : 2006:08:08 15:10:04-05:00 Metadata Date : 2008:06:30 09:31:16-05:00 Document ID : uuid:6168082e-271a-11db-a0aa-0030654b83fc Format : application/pdf Creator : mlea Title : R1415 Assy3.qxd Author : mleaEXIF Metadata provided by EXIF.tools