Visonic MC302VPG2 Vanishing magnetic contact device User Manual D 304535 MC 302V PG2 Installation Guide

Visonic Ltd. Vanishing magnetic contact device D 304535 MC 302V PG2 Installation Guide

Users Manual

D-304535 MC-302V PG2 Installation Guide  1  MCMCMCMC----302V302V302V302V    PG2PG2PG2PG2    Supervised Vanishing Magnetic Contact Device  Installation Instructions 1. INTRODUCTION1. INTRODUCTION1. INTRODUCTION1. INTRODUCTION    The MC-302V PG2 is a very thin PowerG magnetic contact device that  is  compatible  with  PowerMaster  control  panels.  The  device includes  a  built-in  reed  switch  (that  opens  upon  removal  of  a magnet  placed  near  it).  The  MC-302V  PG2  sends  the  alarm message to the control panel using PowerG 2-way communications protocol.  A  periodic  supervision  or  alarm  message  is  transmitted automatically.  The  control  panel  is  thus  informed,  at  regular intervals, of the unit’s active participation in the system. The  LED  lights  green/yellow/red,  according  to  signal  strength, upon first insertion of the battery and for the test period of 15 min. LED does not light while a supervision message is being transmitted. Operating  power  is  obtained  from  an  on-board  3  V  Lithium battery. When the battery voltage is low, a “low battery” message is sent to the receiver. The MC-302 V is available for 433 MHz, 868 MHz, and 915 MHz.   A. Transmission LED  B. Magnet Figure 1:  External View   2222. INSTALLATION. INSTALLATION. INSTALLATION. INSTALLATION    CAUTION: This equipment shall be installed by Service Personnel in non-hazardous indoor locations only. 2.1 Mounting                                     7     7 A.  Enroll button B. Double-sided adhesive tape Figure 2: Mounting Note: The required battery is CR2032 Lithium 3V, manufactured by VARTA or another UL-recognized manufacturer, purchased from a Visonic-approved supplier. Note: To comply with FCC and IC RF exposure compliance requirements, the device should be located at a distance of at least 20 cm from all persons during normal operation. The antennas used for this product must not be co-located or operated in conjunction with any other antenna or transmitter. 1.  Insert a “quarter” coin in the slot, as shown in the drawing, and flex to remove the cover - or, if a “quarter” coin is not available - 2.  Insert a 4 mm flat screwdriver into the slot of the plastic cover, as shown in the drawing, and flex the slot to open that side of the plastic cover. 3.  Insert the screwdriver into the slot on the other side of the plastic cover and repeat the procedure, and then remove the cover. 4.  Insert the battery at an angle (see drawing) while observing battery polarity and then press down on the battery. Caution! Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the manufacturer's instructions. 5.  Peel away the release liners from the two strips of double-sided adhesive tape and attach to the device and magnet. 6.  Align  the  device  with  the  magnet  according  to  the  location  marks  and  fasten  the  device  and  magnet  to  the  mounting  surface.  The transmitter should be mounted on the fixed surface and the magnet on the moving surface. 7. For installers of 433 or 868 MHz model:  Ensure that the heads of the tightened screws are flat perpendicular to the device surface.
2  D-304535 MC-302V PG2 Installation Guide 2.2. Enrollment Refer to the PowerMaster panel's Installer Guide and follow the procedure under the "02:ZONES/DEVICES" option of the Installer Menu. The following is a general description of the steps through the panel menu: 1. 02:ZONES/DEVICES 2. ADD NEW DEVICES > MODIFY DEVICES 3. ENROLL NOW or > ENTR ID:XXX-XXXX 4. Z06:Contact Sens > ID No. 104-XXXX 5. Z06:LOCATION > Z06:ZONE TYPE > Z06:SET CHIME > Z06:DEV SETTINGS   3333. . . . LOCAL DIAGNOSTICS TESTLOCAL DIAGNOSTICS TESTLOCAL DIAGNOSTICS TESTLOCAL DIAGNOSTICS TEST    Before testing, separate the base from the cover (see Figure 2). A.  Put  back  the  cover to  return  the tamper  switch  to its  normal (undisturbed) position. B.  Momentarily open the door or window and verify the red LED blinks, indicating detection. C.  After 2 seconds one of the LED blinks 3 times.  The following table indicates received signal strength indication.     LED response  Reception  Green LED blinks  Strong  Yellow LED blinks  Good  Red LED blinks  Poor  No blinks  No communication IMPORTANT!  Reliable  reception  must  be  assured.  Therefore, "poor"  signal  strength  is  not  acceptable.  If  you  receive  a  "poor" signal  from  the  device,  re-locate  it  and  re-test  until  a  "good"  or "strong" signal strength is received. Note:  For  detailed  Diagnostics  Test  instructions  refer  to  the control panel Installer Guide.  4444. . . . MISCELLANEOUS COMMENTSMISCELLANEOUS COMMENTSMISCELLANEOUS COMMENTSMISCELLANEOUS COMMENTS    Visonic Ltd. wireless systems are very reliable and are tested to high  standards.  However,  due  to  low  transmitting  power  and limited range (required by FCC and other regulatory authorities), there are some limitations to be considered: A.  Receivers  may  be  blocked  by  radio  signals  occurring  on  or near their operating frequencies, regardless of the digital code used.  B.  A receiver responds only to one transmitted signal at a time. C.  Wireless  devices  should  be  tested  regularly  to  determine whether  there  are  sources  of  interference  and  to  protect against faults.  5555. COMPLIANCE WITH STANDARDS. COMPLIANCE WITH STANDARDS. COMPLIANCE WITH STANDARDS. COMPLIANCE WITH STANDARDS          Europe: EN 300220, EN 301489 EN 50130-4, EN 61000-6-3, EN 60950-1  The  MC-302V  PG2  is  compatible  with  the  RTTE  requirements  -  Directive  1999/5/EC  of  the European Parliament and of the Council of 9 March 1999 and EN50131-1 Grade 2 Class I. USA: CFR 47 part 15 (FCC) Canada: RSS 210 The  Power  G  peripheral  devices  have  two-  way  communication  functionality,  providing  additional benefits as described in the technical brochure. This functionality has not been tested to comply with the respective technical requirements and should therefore be considered outside the scope of the product’s certification. EN 50131-1 Security Grade  According to EN 50131-1: this equipment can be applied in installed systems up to and including Security Grade 2. EN 50131-1 Environmental Class  Class I
D-304535 MC-302V PG2 Installation Guide  3 FCC Compliance Statement The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  in  residential  installations.  This  equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to  radio  and  television reception. However, there is  no guarantee that  interference will not occur in a  particular  installation.  If this device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures: –  Re-orient or re-locate the receiving antenna. –  Increase the distance between the device and the receiver. –  Connect the device to an outlet on a circuit different from the one which supplies power to the receiver. – Consult the dealer or an experienced radio/TV technician WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.  This  device  complies  with  FCC  Rules  Part  15  and  with  Industry Canada  licence-exempt  RSS  standard(s).  Operation  is  subject  to  two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation.  Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux  deux  conditions  suivantes  :(1)  l'appareil  ne  doit  pas  produire  de  brouillage,  et  (2)  l'utilisateur  de  l'appareil  doit  accepter  tout  brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.  Reed Switch Positions  Wood Supports Soft Iron XYYZ Fig. 3 Range Coverage Directions Opening  Closing  Direction  Opening  Closing >20mm  <15 mm  X  >15mm  <8mm >13mm  <10mm  Y  >13mm  <10mm >24mm  <15mm  Z  >10mm  <8mm  APPENDIX: SPECIFICATIONSAPPENDIX: SPECIFICATIONSAPPENDIX: SPECIFICATIONSAPPENDIX: SPECIFICATIONS    Frequency Band (MHz) 433, 868, 915 (in accordance with the prevailing frequency of your region) Modulation GFSK Antenna Built-in loaded inverted-F antenna Communication Protocol PowerG Supervision Signaling at 256 sec. intervals Battery type Varta 3V Lithium CR2032 type battery Battery Life Expectancy 5 years  Low Battery Threshold 2.1 V Operating Temperature 0°C to 50°C (32°F to 122°F) Storage Temperature -40°C to 85°C (-40°F to 185°F) Relative Humidity (RH) Up to 95% non-condensing Dimensions (LxWxD) 433/868 MHz model: 62 x 25.4 x 7.7 mm (2-1/2 x 1 x 1/3 in.) 915 MHz model: 62 x 25.4 x 6.1 mm (2-1/2 x 1 x 1/4 in.) Weight (including battery) 12g (0.42 oz) Color  White or brown
4  D-304535 MC-302V PG2 Installation Guide WARRANTY  Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the “Purchaser”)  against  defective  workmanship  and  materials  under  normal  use  of  the  Product  for  a  period  of twelve (12) months from the date of shipment by the Manufacturer.   This  Warranty  is  absolutely  conditional  upon  the  Product  having  been  properly  installed,  maintained  and operated under  conditions  of  normal  use in  accordance with the Manufacturers recommended installation  and operation  instructions.    Products  which  have  become  defective  for  any  other  reason,  according  to  the Manufacturers  discretion,  such  as  improper  installation,  failure  to  follow  recommended  installation  and operational  instructions,  neglect,  willful  damage,  misuse  or  vandalism,  accidental  damage,  alteration  or tampering, or repair by anyone other than the manufacturer, are not covered by this Warranty. The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the Product  will  prevent  any  death  and/or  personal  injury  and/or  damage    to  property  resulting  from  burglary, robbery,  fire  or  otherwise,  or  that  the  Product  will  in  all  cases provide  adequate warning or  protection.      The Product, properly installed and maintained, only reduces the risk of such events without warning and it is not a guarantee or insurance that such events will not occur.  THIS  WARRANTY  IS  EXCLUSIVE  AND  EXPRESSLY  IN  LIEU  OF  ALL  OTHER  WARRANTIES, OBLIGATIONS  OR  LIABILITIES,  WHETHER WRITTEN, ORAL, EXPRESS  OR  IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE.  IN NO  CASE  SHALL  THE  MANUFACTURER  BE  LIABLE  TO  ANYONE  FOR  ANY  CONSEQUENTIAL  OR INCIDENTAL  DAMAGES  FOR  BREACH  OF  THIS  WARRANTY  OR  ANY  OTHER  WARRANTIES WHATSOEVER, AS AFORESAID. THE  MANUFACTURER  SHALL  IN  NO  EVENT  BE  LIABLE FOR  ANY  SPECIAL,  INDIRECT,  INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS OF  USE,  PROFITS,  REVENUE,  OR  GOODWILL,  DIRECTLY  OR  INDIRECTLY  ARISING  FROM PURCHASER’S  USE  OR  INABILITY  TO  USE  THE  PRODUCT,  OR  FOR  LOSS  OR  DESTRUCTION  OF OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. THE  MANUFACTURER  SHALL  HAVE  NO  LIABILITY  FOR  ANY  DEATH,  PERSONAL  AND/OR  BODILY INJURY  AND/OR  DAMAGE  TO  PROPERTY  OR  OTHER  LOSS  WHETHER  DIRECT,  INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION.  However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive remedy against the Manufacturer.  When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty and he recognizes having been informed of. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these limitations may not apply under certain circumstances.  The Manufacturer  shall  be  under  no  liability  whatsoever  arising  out  of  the  corruption  and/or malfunctioning of any telecommunication or electronic equipment or any programs. The  Manufacturers  obligations  under  this  Warranty  are  limited  solely  to  repair  and/or  replace  at  the Manufacturer’s discretion any Product or part thereof that may prove defective.  Any repair and/or replacement shall not extend the original Warranty period.  The Manufacturer shall not be responsible for dismantling and/or reinstallation costs.  To exercise this Warranty the Product must be returned to the Manufacturer freight pre-paid and insured.   All freight and insurance costs are the responsibility of the Purchaser and are not included in this Warranty. This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to act  on  its  behalf  in  the  modification,  variation  or  extension  of  this  warranty.  This  warranty  shall  apply  to  the Product only.  All products, accessories or attachments of others used in conjunction with the Product, including batteries,  shall  be  covered solely  by  their  own warranty,  if  any.    The  Manufacturer shall  not  be  liable  for  any damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, caused by the malfunction of  the Product due  to  products, accessories, or attachments of others, including batteries, used in conjunction with the Products. This Warranty is exclusive to the original Purchaser and is not assignable.  This  Warranty  is  in  addition  to  and  does  not  affect  your  legal  rights.  Any  provision  in  this  warranty  which  is contrary to the Law in the state or country were the Product is supplied shall not apply.  Warning: The user must follow the Manufacturer’s installation and operational instructions including testing the Product and its whole system at least once a week and to take all necessary precautions for his/her safety and the protection of his/her property. 1/08                                                             W.E.E.E. Product Recycling Declaration For    information  regarding  the recycling   of this product  you must contact the  company from which you orignially purchased it. If you are  discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste. Directive 2002/96/EC Waste Electrical and Electronic Equipment.    EMAIL: info@visonic.com INTERNET: www.visonic.com VISONIC LTD. 2013      MC-302V (ROW)  D-304535 (REV. 1, 10/13)

Navigation menu