Visonic MCT430 Photoelectric Smoke Detector User Manual Instr

Download:
Mirror Download [FCC.gov]
Document ID	278792
Application ID	iquCTQYwFijvzzHe6peMhw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	14.96kB (186998 bits)
Date Submitted	2002-10-24 00:00:00
Date Available	2002-10-23 00:00:00
Creation Date	2002-10-14 16:46:24
Producing Software	Acrobat PDFWriter 4.0 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	Instr.PDF
Document Creator	Microsoft Word
Document Author:	valeria

MCT-430
Supervised Wireless PowerCode Smoke Detector
Installation Instructions
1. INSTALLATION SUMMARY
1.1 General Description
1.3 Enrolling Transmitter’s Power- Code ID
The MCT-430 is a low profile, battery operated, photoelectric
smoke detector which shares its housing with a UHF PowerCode
type transmitter. It has a 57°C (135°F) fixed temperature heat
detector and a built-in sounder. The detector sends out the
following messages to the control panel:
• Smoke alarm
• Heat alarm
• Tamper alert
• Low battery alert
• Trouble message (when heat sensor malfunctions)
• Service alert (degraded smoke detection sensitivity - internal
screen requires cleaning).
During normal and low battery conditions, the LED flashes
approximately once every 40 seconds. The smoke/heat detector
will sound its built-in temporal horn when smoke activates the
detector (the LED flashes rapidly), or when the air temperature
reaches 57°C (135°F). A message is also sent to the wireless
control panel. After the horn stops, a RESTORE message is
transmitted to the control panel and the ID number can be
cleared from the panel. The built-in Drift Compensation algorithm
automatically maintains the sensitivity of the detector. Once the
detector reaches its limit of compensation, it transmits a
maintenance signal to the panel. When maintenance is required,
the LED stops flashing.
The maintenance signal fully complies with the sensitivity test
requirement specified in NFPA 72, 7 - 2.2.
The detector includes a tamper switch that causes a tamper alert
when the main body is separated from its mounting bracket. This
switch protects the unit against unauthorized handling.
The detector has two separate PowerCode IDs:
• The first ID is linked to messages containing alarm, low
battery and supervision data.
• The second ID is linked to messages containing tamper and
maintenance data such as “clean” and circuit trouble.
Enrolling process to the PowerMax is differennt from the enrolling
process to other versions of the PowerMax (PowerMax+,
PowerMax GSM....), as described in par. 1.3.1 and 1.3.2.
1.3.1 Enrolling to PowerMax Control Panel
It is necessary that the control panel will learn the two IDs before
the detector is actually mounted in place. This is best carried out
in close proximity to the control panel. Each ID must be enrolled
to a separate zone of the control panel.
A. Refer to the control panel’s installation instructions and follow
the procedure given there for enrolling transmitter IDs in the
control panel's memory.
2nd. When required to initiate a transmission for enrollment of
the first ID, activate the test switch (see fig. 1) until the builtin horn sounds (see Para. 1.2B).
C. When you are instructed to initiate a transmission for
enrollment of the second ID, separate the detector from the
bracket to activate a tamper message.
Important: If the second ID is not learnt by the control panel,
the maintenance and tamper messages will not be received.
Note: The PowerMax control panel can not distinguish
between “clean” and circuit trouble data. Upon receiving a
maintenance alert, clean the internal screen as described in
Para. 5.2. If the maintenance alert persists, the trouble is
probably due to a circuit failure.
1.3.2 Enrolling to Other Versions of PowerMax
(PowerMax+, PowerMax GSM...)
Figure 1. General View
1.2 Power Up and Initial Test
The smoke detector is supplied with two 3V batteries seated
within their holder but insulated from the battery terminals.
A. Turn the detector upside down and pull out the paper tab that
insulates the batteries from one of the terminals.
B. Insert a sharp object into the test switch hole and push the
switch in continuously, until the built-in horn sounds (about
2.5 seconds after depressing the button). The sounding
sequence is: 3 beeps - short break - 3 beeps ......and so on
until you release the switch. In addition, the LED will flash
rapidly a few times. This means that the smoke detection
section is working properly.
DE3643
To enroll the transmitters IDs to the PowerMax+, PowerMax GSM
and above, it is necessary to enrol only one ID, the first ID or the
second ID (for IDs description refer to par. 1.3). When either ID
is enrolled to one zone, the second ID is automatically enrolled.
The enrolling process is as follows:
A. Refer to the control panel’s installation instructions and follow
the procedure given there for enrolling transmitter IDs in the
control panel's memory.
2nd. When you are instructed to initiate a transmission for
enrollment of the ID, activate the test switch until the built-in
horn sounds (see Para. 1.2B), or separate the detector from
the bracket to activate a tamper message.
1.4 Mounting the Bracket in Place
Read Section 4 in this manual first, then decide where to install
the detector. Refer to Figure 2 and proceed according to the
following instructions.
1st.If the detector is attached to the bracket, separate it from the
bracket by holding the bracket in one hand and turning the
detector slightly counterclockwise with your other hand.
Note: Removal of the unit from the bracket will initiate a tamper
alert! The LED will flash but the horn will remain silent.
2nd.Press the bracket against the mounting surface and mark the
drilling spots through two mounting screw bays.
C. Drill two 5 mm (3/16”) holes at the marked spots.
D. Attach the bracket to the wall, using the two screws and
plastic wall anchors (supplied).
1.5 Assembly and Test
Figure 2. Mounting Bracket
A. Align the marks on the detector’s body with the arrows on the
bracket. Push the detector against the bracket and turn it slightly
clockwise until it snaps into place. Pull outward to make sure
that the detector is securely attached to the bracket.
B. Press the test button until the built-in horn sounds. Verify that
the transmitted signal has been received at the control panel,
and that the control panel responds accordingly by activating
the fire alarm siren or any other warning device.
2. MISCELLANEOUS WARNINGS
WARNING: This smoke detector is designed for use in a single
residential unit only, which means that it should be used inside a
single family home or apartment. It is not meant to be used in
lobbies, hallways, basements or another apartment in multi-family
buildings, unless there are already working detectors in each
family unit. Smoke detectors, placed in common areas outside the
individual living unit, such as on porches or in hallways, may not
provide early warning to residents. In multi-family buildings, each
family living unit should set up its own detector.
WARNING: This detector is not meant to be used in nonresidential buildings. Warehouses, industrial or commercial
buildings and special purpose non-residential buildings require
special fire detection and alarm systems. This detector alone is
not a suitable substitute for complete fire detection systems for
places where many people live or work, such as hotels or motels.
The same is true of dormitories, hospitals, nursing homes or
group homes of any kind, even if they were once single family
homes. Please refer to NFPA 101, the Life Safety Code,
NFPA71, 72A, 72B, 72C, 72D and 72E for smoke detector
requirements for fire protection in buildings not defined as
"households".
WARNING: This detector, if used as a stand-alone unit, will not
alert people who are hard of hearing.
3. SPECIFICATIONS
SMOKE AND HEAT DETECTION
Activity Indicator: LED flashes once per 40 sec.
Nominal Smoke Detection Sensitivity: 2.25% per foot obscuration
Heat Detection: Alarm if ambient temperature exceeds 57°C
(135°F)
Alarm Sound Level: 85 dB min at 3 m (10 ft) at minimum battery
voltage
TRANSMITTER AND CODING
Operating Frequency (MHz): 315
Transmitter's ID Code: 24-bit digital word, over 16 million
combinations, pulse width modulation.
Overall Message Length: 36 bits
Supervision: Automatic signaling at 60-minute intervals.
Tamper Alerts: Tamper event (removal of the unit from its bracket)
is reported once. Tamper restore is also reported once.
Compliance with standards: Designed to meet FCC part 15,
MPT 1340 UL 268 recognized component.
ELECTRICAL DATA
Power Source: Two CR123A lithium batteries in series (6 VDC
nominal).
Operating Voltage Range: 4.8 - 6.5 VDC
Current Drain: 14.5 µA standby (typical), 20 mA typical in
operation
Battery Life (at room temperature): 3 years typical
Battery Supervision: Once every 60 minutes; automatic
transmission of battery status data as part of any transmitted
message.
PHYSICAL DATA
Operating Temperature: 0°C to 38°C (32°F to 100°F)
Relative Humidity: 10% to 93%, non-condensing
Dimensions: 140 mm (5.5") diameter with bracket x 52 mm (2.05")
Weight (with batteries): 218 g (7 oz)
4. SMOKE DETECTOR INSTALLATION OVERVIEW
4.1 Where to Install Smoke Detectors
Smoke detectors should be installed in accordance with the
NFPA (National Fire Protection Association, Batterymarch Park,
MA 02269-9101) Standard 72. For complete coverage in
residential units, smoke detectors should be installed in all
rooms, halls, storage areas, basements and attics in each family
living unit. Minimum coverage is one detector on each floor and
one in each sleeping area. Here are a few useful tips for you:
• Install a smoke detector in the hallway outside every separate
bedroom area, as in Figure 3. Two detectors are required in
homes with two bedroom areas, as in Figure 4.
• Install a smoke detector on every floor of a multi-floor home or
apartment, as shown in Figure 5.
• Install a minimum of two detectors in any household.
• Install a smoke detector inside every bedroom.
• Install smoke detectors at both ends of a bedroom hallway if
the hallway is more than 12 meters (40 feet) long.
• Install a smoke detector inside every room where one sleeps
with the door partly or completely closed, since smoke could be
blocked by the closed door and a hallway alarm may not wake
up the sleeper if the door is closed.
DE3643
Figure 3. Placement of a Smoke/Heat Detector in a Single-Floor
Residence with Only One Sleeping Area
(1) A smoke detector installed in each separate sleeping area (in
the vicinity, but outside the bedrooms), and (2) Heat or smoke
detectors in the living rooms, dining rooms, bedrooms, kitchens,
hallways, attics, furnace rooms, closets, utility and storage
rooms, basements and attached garages."
For your information, NFPA Standard 72, Section 2-2.1.1.1 reads
as follows:
"Smoke detectors shall be installed outside each separate
sleeping area in the immediate vicinity of the bedrooms and on
each additional story of the family living unit including basements
and excluding crawl spaces and unfinished attics. In new
construction, a smoke detector also shall be installed in each
sleeping room."
The above NFPA standard is a minimum requirement for smoke
detector installation. For better protection, we also require the
installation of a smoke detector inside every bedroom in existing
construction.
4.2 Where Not to Install Smoke Detectors
False alarms occur when smoke detectors are installed where
they will not work properly. To avoid false alarms, do not install
smoke detectors in the following situations:
• In or near areas where combustion particles are normally
Figure 4. Placement of Smoke/Heat Detectors in Single-Floor
Residence with More than One Sleeping Area
present such as kitchens; in garages where there are
particles of combustion in vehicle exhausts; near furnaces,
hot water heaters, or gas space heaters. Install detectors
at least 20 feet (6 meters) away from kitchens and other
areas where combustion particles are normally present.
• On the ceiling in rooms next to kitchens where there is no
transom between the kitchen and these rooms. Instead, install
the smoke detector on an inside wall, furthest from the kitchen.
Be sure not to install smoke detectors within 4" of the ceiling or
any corner or more than 6" from the ceiling.
• In damp or very humid areas, or next to bathrooms with
showers.
Figure 5. Placing Smoke/Heat Detectors in a Multi-Floor Residence
• The moisture in humid air can enter the sensing chamber as
• Install basement detectors at the bottom of the basement
water vapor, then cool and condense into droplets that cause a
nuisance alarm. Install detectors at least 5 feet (1.5 meters)
away from bathrooms.
• In very cold or very hot rooms or areas. Operating temperature
of the smoke detector is 40°F to 100°F (4°C to 38°C).
• In dusty, dirty, or insect-infested areas. Dust and dirt can
build up on the detector’s sensing chamber and make it overly
sensitive, or can block openings to the sensing chamber and
keep the detector from sensing smoke.
• Near fresh air inlets or returns or excessively drafty areas.
Air conditioners, heaters, fans, and fresh air intakes and
returns can drive smoke away from smoke detectors, making
the detectors less effective.
stairwell, as shown in Figure 5.
• Install second-floor detectors at the top of the first-to-second
floor stairwell.
• Be sure no door or other obstruction blocks the path of smoke
to the detector.
• Install additional detectors in your living room, dining room,
family room, attic, utility and storage rooms.
• Install smoke detectors as close to the center of the ceiling as
possible. If this is not practical, put the detector on the ceiling,
at least 10 cm (4 inches) away from any wall or corner, as
shown in Figure 6.
• If ceiling mounting is not possible and wall mounting is
permitted by your local and state codes, put wall-mounted
detectors between 10 - 15 cm (4 - 6 inches) from the ceiling,
also shown in Figure 6.
• If some of your rooms have sloped, peaked, or gabled ceilings,
try to mount detectors 0.9 meter (3 feet) measured horizontally
from the highest point of the ceiling, as shown in Figure 7.
Figure 6. Recommended Best
and Acceptable Locations to
Mount Smoke Detectors
Figure 7. Recommended
Location to Mount Smoke
Detectors in Rooms with
Sloped, Gabled or Peaked
Ceilings
• In dead air spaces at the top of a peaked ceiling or wall/ceiling
intersect. Dead air may prevent smoke from reaching a detector.
• Near fluorescent light fixtures. Install detectors at least 10
feet (3 meters) away from such light fixtures.
Figure 8. Recommended Smoke Detector Locations to Avoid Air
Streams with Combustion Particles
CAUTION (As required by California State Fire Marshall)
"Early warning fire detection is best achieved by the
installation of fire detection equipment in all rooms and
areas of the household as follows:
DE3643
WARNING: Never remove batteries to stop a nuisance alarm.
Open a window or fan the air around the detector to get rid of the
smoke. The alarm will turn itself off when the smoke is gone. If
nuisance alarms persist, attempt to clean the detector as
described in this manual.
WARNING: Do not stand close to the detector when the alarm is
sounding. The alarm is loud in order to wake you in an
emergency. Too much exposure to the horn at close range may
be harmful to your hearing.
4.3 Smoke Detector Limitations
• Smoke detectors will not sense a fire if the smoke does not
reach the sensor or if the air temperature does not reach
57°C (135°F). In order for a smoke detector to sense smoke, it
must be installed in the immediate vicinity of the fire. In
addition, smoke from fires in chimneys, in walls, on roofs, in
remote parts of the building, or on another level from where the
smoke detector is located, may not reach the smoke detector
quickly enough for occupants to escape unharmed. For this
reason, the installer shall install smoke detectors on every
level, in every sleeping area, and in every bedroom of the
household.
• Smoke detectors may not be heard. The alarm horn in this
smoke detector meets or exceeds current Underwriter’s
Laboratories standards. However, if the smoke detector is not
located in the same room as the occupant, or if it is blocked by
a closed door or normal noise, the alarm horn may not be
heard. In addition, sound sleepers, or persons who are under
the influence of drugs or alcohol may not hear the alarm or be
able to react to it. Therefore, locate this smoke detector,
which has a sounder rated at 85 dB at 10 feet, on every
level, in every sleeping area, and in every bedroom of the
household.
• In general, detectors may not always warn you about fires
caused by carelessness and safety hazards like smoking in
bed, violent explosions, escaping gas, improper storage of
flammable materials, overloaded electrical circuits, children
playing with matches, or arson.
• Smoke detectors are not fool-proof. Like all electronic
devices, smoke detectors have limitations. No type of
smoke detector can sense every kind of fire every time. In
addition, smoke from slow, smoldering fires rises slowly
and may not reach the smoke detector until actual flame
breaks out. This type of smoke may not reach the smoke
detector in time for occupants to escape unharmed.
• Smoke detectors are not a substitute for life or property
insurance. Though smoke detectors have been responsible for
saving many lives, they are not warranted or implied to protect
lives or property in the event of a fire.
• To keep your equipment in excellent working order, ongoing
maintenance is required per the manufacturer’s recommendations and UL and NFPA standards. At a minimum, the
requirements of Chapter 7 of NFPA 72, The National Fire
Alarm Code, shall be followed. A preventative maintenance
agreement should be arranged through the local manufacturer’s representative. Though smoke detectors are designed
for long life, they may fail at any time. Any smoke detector, fire
alarm equipment, or any component of that system which fails
shall be repaired or replaced as soon as possible.
5. MAINTENANCE
5.1 Battery Replacement
The detector checks for low batteries at least every 60 minutes. If
the batteries are low, the transmitter sends a low battery message
to the control panel. This condition will exist for a minimum of seven
days, and then the detector's horn will "chirp" about every 40
seconds. The batteries should be replaced before the chirps begin.
Be sure to replace both batteries with fresh ones.
To replace batteries:
A. Remove the detector from its bracket by twisting the detector
counterclockwise, remove batteries, and dispose properly.
B. Install two new 3-volt CR123A lithium batteries in the battery
compartment. Follow the polarity diagram inside the
compartment.
C. Reinstall the smoke detector onto the bracket by turning the
detector clockwise.
D. Test the detector as described in Para. 1.2 of this manual.
The LED should flash about once every 40 seconds to
indicate normal operation. If the batteries are not installed
correctly, the smoke detector will not operate and the batteries
may be damaged. If the detector does not appear to be
sending a signal during any of the tests, check for correct
battery installation.
screwdriver and pull the housing from the base. Use caution
to avoid damaging the thermistors.
D. Vacuum the screen carefully without removing it.
E. Remove the screen assembly, pulling straight out (see Fig.
10).
Figure 9. Housing Removal
5.2 Cleaning
Before removing the detector, notify the proper authorities that
the smoke detector system is undergoing maintenance and will
be temporarily out of service. Disable the zone or system
undergoing maintenance to prevent unwanted alarms.
Before removing the detector cover, note the position of the
thermistors (see Figure 1). Make sure the thermistors are not
bent over when the housing is replaced.
Refer to Figure 9 and proceed as follows:
A. Grasp the detector’s body with your hands, rotate it slightly
counterclockwise and pull it off the wall-mounted bracket.
B. Remove the batteries at the bottom.
C. Remove the detector housing by gently prying the four
housing tabs on the bottom of the base with a small-bladed
DE3643
Figure 10. Removal of Cover and Screen for Cleaning
DE3643
F. Remove the sensing chamber cover.
G. Clean the sensing chamber by vacuuming or blowing out dust
and particles.
H. Replace the sensing chamber cover, aligning the arrow on the
cover top with the arrow on the printed circuit board.
I. Replace the screen by placing the screen assembly over the
sensing chamber cover and twisting until it snaps into place.
J. Replace the housing by aligning the two triangular slots on the
base with their counterparts on the housing. Gently press the
housing until it locks in place. Check to make sure that the
thermistors are in the upright position.
K. Replace the batteries (verify correct polarity).
L. Reinstall the detector.
M. Notify the proper authorities that the system is back in
operation.
NOTE: Test the detector to make sure that the batteries are
inserted correctly.
NOTE: If nuisance alarms keep occurring, check whether the
detector's location is adequate (see Para. 4.1 and 4.2). Relocate
the unit if it is not located properly. Clean as described above.
6. ROUTINE TESTING
The detector should be tested weekly and also whenever you
suspect that it does not go into alarm. Push the test switch firmly
with a sharp object until the horn sounds (it may take up to 2.5
seconds). Also verify that the control panel responds to the
transmitted fire alarm. If the detector fails, have it repaired or
replaced immediately, to ensure that it works properly.
WARNING: Never use an open flame of any kind to test your
detector. You may set fire to damage the detector as well as
your home. The built-in test switch accurately tests all
detector functions, as required by Underwriters' Laboratories. This is the only correct way to test the unit.
NOTE: If the alarm horn produces a loud continuous sound when
you are not testing the unit, this means the detector has sensed
smoke or combustion particles in the air. Verify that the alarm is a
result of a possible serious situation, which requires your
immediate attention.
• The alarm could be caused by a nuisance situation. Cooking
smoke or a dusty furnace, sometimes called "friendly fires" can
cause the alarm to sound. If this happens, open a window or
fan the air away to remove the smoke or dust. The alarm will
turn off as soon as the air is completely clear.
CAUTION: Do not disconnect the battery from the detector. This
will remove your protection from fires.
• If the alarm horn begins to chirp once every 40 seconds, this
means that the detector's battery is weak. Install a new battery
immediately. Keep fresh batteries on hand for this purpose.
7. STATEMENTS OF COMPLIANCE
The 315 MHz version of this device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This
device must accept any interference received, including
interference that may cause undesired operation.
WARNING! Changes or modifications to this unit not
expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment
The digital circuit of this device has been tested and found to
comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in residential
installations. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio and television reception. However, there is no guarantee
that interference will not occur in a particular installation. If this
device does cause such interference, which can be verified by
turning the device off and on, the user is encouraged to eliminate
the interference by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the
one which supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
At 315 MHz the product complies with FCC and UL requirements.
APPENDIX A. THE VISONIC LTD. POWERCODE SYSTEM
The PowerCode Message Format
PowerCode transmitters transmit 3 data bursts at random intervals, with 6 repetitions of the same message in each burst (Fig. A1). This
redundancy improves the probability of reception.
Note: Periodic supervision messages are an exception to this rule - they consist of a single 9-message burst.
Figure A1. Anti-Collision Transmission Sequence
DXXXX
WARRANTY
Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its
products hereinafter referred to as "the Product" or "Products" to be in conformance with
its own plans and specifications and to be free of defects in materials and workmanship
under normal use and service for a period of twelve months from the date of shipment by
the Manufacturer. The Manufacturer's obligations shall be limited within the warranty
period, at its option, to repair or replace the product or any part thereof. The Manufacturer
shall not be responsible for dismantling and/or reinstallation charges. To exercise the
warranty the product must be returned to the Manufacturer freight prepaid and insured.
This warranty does not apply in the following cases: improper installation, misuse,
failure to follow installation and operating instructions, alteration, abuse, accident or
tampering, and repair by anyone other than the Manufacturer.
This warranty is exclusive and expressly in lieu of all other warranties, obligations or
liabilities, whether written, oral, express or implied, including any warranty of
merchantability or fitness for a particular purpose, or otherwise. In no case shall the
Manufacturer be liable to anyone for any consequential or incidental damages for breach
of this warranty or any other warranties whatsoever, as aforesaid.
This warranty shall not be modified, varied or extended, and the Manufacturer does not
authorize any person to act on its behalf in the modification, variation or extension of this
warranty. This warranty shall apply to the Product only. All products, accessories or
attachments of others used in conjunction with the Product, including batteries, shall be
covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or
otherwise, caused by the malfunction of the Product due to products, accessories, or
attachments of others, including batteries, used in conjunction with the Products.
The Manufacturer does not represent that its Product may not be compromised and/or
circumvented, or that the Product will prevent any death, personal and/or bodily injury
and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the
Product will in all cases provide adequate warning or protection. User understands that a
properly installed and maintained alarm may only reduce the risk of events such as
burglary, robbery, and fire without warning, but it is not insurance or a guarantee that such
will not occur or that there will be no death, personal damage and/or damage to property
as a result.
The Manufacturer shall have no liability for any death, personal and/or bodily injury
and/or damage to property or other loss whether direct, indirect, incidental,
consequential or otherwise, based on a claim that the Product failed to function.
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or
damage arising under this limited warranty or otherwise, regardless of cause or origin, the
Manufacturer's maximum liability shall not in any case exceed the purchase price of the
Product, which shall be fixed as liquidated damages and not as a penalty, and shall be the
complete and exclusive remedy against the Manufacturer.
Warning: The user should follow the installation and operation instructions and among
other things test the Product and the whole system at least once a week. For various
reasons, including, but not limited to, changes in environmental conditions, electric or
electronic disruptions and tampering, the Product may not perform as expected. The user
is advised to take all necessary precautions for his/her safety and the protection of his/her
property.
6/91
VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788
VISONIC INC. (U.S.A.): 10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: (860) 243-0833, (800) 223-0020 FAX: (860) 242-8094
VISONIC LTD. (UK):
FRASER ROAD, PRIORY BUSINESS PARK, BEDFORD MK44 3WH. PHONE: (0870) 730-0800 FAX: (0870) 730-0801
DE3640
INTERNET:
www.visonic.com
VISONIC LTD. 2002
MCT-430
DE3643- (REV. 0, 10/02)
DE3643

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 8
Creator                         : Microsoft Word
Create Date                     : 2002:10:14 16:46:24
Title                           : Instr.PDF
Author                          : valeria
Producer                        : Acrobat PDFWriter 4.0 for Windows

EXIF Metadata provided by EXIF.tools