Visonic PGMODEMLP Power-G Modem LP Module User Manual Power G Modem LP Module
Visonic Ltd. Power-G Modem LP Module Power G Modem LP Module
Visonic >
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3962456 |
| Application ID | ftIgW3nlvmWI6RqFAYnqhw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 21.1kB (263811 bits) |
| Date Submitted | 2018-08-14 00:00:00 |
| Date Available | 2018-08-16 00:00:00 |
| Creation Date | 2018-08-09 10:37:46 |
| Producing Software | Adobe PDF Library 11.0 |
| Document Lastmod | 2018-08-13 07:15:15 |
| Document Title | Power-G Modem LP Module |
| Document Creator | Acrobat PDFMaker 11 for Word |
| Document Author: | jkenneka |
POWER-G Modem LP Module 1. INTRODUCTION The Power-G Modem LP is a wireless transceiver designed for providing simple access to wireless devices. Its main application is an RF interface in a security system that communicates PG messages. The transceiver features UART ports that can be applied to the host of the control panel. Mechanical support and electrical connections are obtained by mounting the modem on an 8-pin connector and fastening it with a screw. 2. SPECIFICATIONS Frequency band: USA: 912-919 MHz Bandwidth: 118 kHz Data rate: 50 Kb/s Communication interface: UART Antenna input: Coaxial connector U. FL-R-SMT-1(60) – Herose Supply voltage: 3.3V +/-5% Transmit current consumption: 45mA Receiver current consumption: 25mA Operating temperature: -10 + 55 °C Dimensions: 57x25x7mm 3. INSTALLATION Installation Instructions 4. COMPLIANCE WITH STANDARDS USA: FCC 47CFR Part 15 Canada: IC RSS-247 Visonic Ltd. P/M/N: Power-G Modem Module FCC ID: WP3PGMODEMLP IC: 1467C- PGMODEMLP LP OEM Integration Notices This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC or authorization. End Product Labeling This transceiver module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example: wireless AP, wireless Router). The final end product must be labeled in a visible area with the following: “Contains TX FCC ID: WP3PGMODEMLP; IC: 1467C-PGMODEMLP”. Figure 1 Callout Description Antenna connector U. FL-R-SMT-1(60) – HEROSE J1 connector Not used Not used Support screw 25.0 mm 57.0 mm Function: J1 connector 1. 2. 3. 4. 5. 6. 7. 8. VCC – Operating voltage: Nominal voltage: 3.3V UART_Rx – Serial asynchronous UART receive port Minimum high input level: 2.3V Maximum low input level: 0.99V UART_Tx – Serial asynchronyous UART transmit port Maximum voltage: 3.3 + 0.3V Mimimum voltage: -0.3V GND RST – low level active SYSTEM_INT – output, low level active, BOOT0 – input, low level active Not used Not used D-307567 OEM Manual Information That Must be Included The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrate this module. The users manual for OEM integrators must include the following information in a prominent location: “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter." This device complies with Part 15 of the FCC Rules and RSS-247 of ISED. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. To comply with FCC and IC RF exposure compliance requirements, the device should be located at a distance of at least 20 cm from all persons during normal operation. The antennas used for this product must not be co-located or operated in conjunction with any other antenna or transmitter. Le dispositif doit être placé à une distance d'au moins 20 cm à partir de toutes les personnes au cours de son fonctionnement normal. Les antennes utilisées pour ce produit ne doivent pas être situés ou exploités conjointement avec une autre antenne ou transmetteur. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. This class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe B est conforme a la norme NMB003 du Canada. WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. W.E.E.E. Product Recycling Declaration For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste. European Directive 2002/96/EC Waste Electrical and Electronic Equipment. EMAIL: info@visonic.com INTERNET: www.visonic.com ©VISONIC LTD. 2018 Power-G Modem LP Transceiver Module D-307567 (Rev 0. 08/18) D-307567
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : jkenneka Company : Visonic Ltd Create Date : 2018:08:09 10:37:46+01:00 Information Classification : Internal MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Application: Microsoft Azure Information Protection MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Enabled: True MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Extended MSFT Method: Automatic MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Name: Internal MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Owner: jkenneka@jci.com MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Ref: https://api.informationprotection.azure.com/api/a1f1e214-7ded-45b6-81a1-9e8ae3459641 MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Set Date: 2018-05-30T09:20:05.6192755+01:00 MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Site Id: a1f1e214-7ded-45b6-81a1-9e8ae3459641 Modify Date : 2018:08:13 07:15:15+03:00 Source Modified : D:20180809093730 Subject : installation Tag Ad Hoc Review Cycle ID : -479190220 Tag Author Email : assistencia.visonic@netvisao.pt Tag Author Email Display Name : assistencia.visonic Tag Email Subject : multilingual documents - MCT-302 Tag Previous Ad Hoc Review Cycle ID: -1133459684 Tag Reviewing Tools Shown Once : Language : EN-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2018:08:13 07:15:15+03:00 Creator Tool : Acrobat PDFMaker 11 for Word Document ID : uuid:4d367358-c4c5-4001-9c19-58706d1b2c21 Instance ID : uuid:b863af40-bead-49a2-9e81-e66626eb7484 Format : application/pdf Title : Power-G Modem LP Module Description : installation Creator : jkenneka Producer : Adobe PDF Library 11.0 Information 0020 Classification : Internal Page Layout : OneColumn Page Count : 2EXIF Metadata provided by EXIF.tools