Von Duprin 98/99 Series Catalog 106590
User Manual: Von Duprin 98/99 Series Catalog Catalog
Open the PDF directly: View PDF 
.
Page Count: 76
| Download | |
| Open PDF In Browser | View PDF |
98/99™ Series Exit devices Introduction Exit devices are a critical part of the fire and life safety egress system and will provide safe and reliable service when properly applied and maintained. Von Duprin designs and manufactures exit devices in accordance to ISO 9001 Quality Management System and meets or exceeds accepted U.S. domestic and International standards. All 98 and 99 Series exit devices are UL listed for panic hardware or fire hardware, and are certified to ANSI A156.3, 2008, Grade 1. Many models are also certified for Hurricane Resistant Applications. Consult your local Security & Safety consultant (SSC) or the Von Duprin factory for current listings. It is intended that the information included in this publication, when properly used, will provide clear and reliable guidelines to the proper general selection and application. However, the scope of the information is necessarily limited. 98 Series features smooth mechanism case. 99 Series features grooved mechanism case. Von Duprin exit devices are available in two external surface styles, designated 98 and 99 Series. The Quiet One® A fluid damper decelerates the pushpad on its return stroke and eliminates most noise associated with exit device operations. Furnished on all 98/99™ Series exit devices. VON DUPRIN Administrative Offices 2720 Tobey Dr. Indianapolis, IN 46219 2 • Von Duprin 98/99 Series Customer Service 877-671-7011 800-999-0328 - Fax Latch bolt Deadlocking latchbolt provides security and improved performance at standard device cost. Technical Support 877-671-7011 Table of contents Exit hardware Fire exit hardware Rim devices Rim devices 98/99E 8 98-F/99E-F 10 Trim 9 Trim 11 Mortise lock devices Mortise lock devices 9875/9975 12 9875-F/9975-F 14 Trim 13 Trim 15 Surface mounted Vertical rod devices Surface mounted Vertical rod devices 9827/9927 16 9827-F/9927-F 18 Trim 17 Trim 19 Three-point latching devices Three-point latching devices 9857/9957 20 9857-F/9957-F 22 Trim 21 Trim 23 Concealed vertical rod devices Concealed vertical rod devices 9847/9947 24 9847-F/9947-F 26 Trim 25 Trim 27 9848/9948 28 9848-F/9948-F 30 Trim 29 Trim 31 Concealed vertical cable devices Concealed vertical cable devices 9849/9949 32 9849-F/9949-F 34 Trim 33 Trim 35 Wood door concealed vertical rod devices Wood door concealed vertical rod devices 9847WDC/9947WDC 36 9847WDC-F/9947WDC-F 38 Trim 37 Trim 39 Wood door concealed vertical cable devices Wood door concealed vertical cable devices 9849WDC/9949WDC 40 9849WDC-F/9949WDC-F 42 Trim 41 Trim 43 Von Duprin 98/99 Series • 3 Options and accessories Applications & trim operation Single & double door applications Door handing Outside trim operation Lever styles Trim options Knob Thumbpiece Lever Electrified outside lever trim (E996L) Breakaway lever Thumbturn control Hospital pull Offset pull Vandal resistant pull AD-Series adaptable electronic trim Strike options Strike/Stile information Strikes Dogging options Cylinder dogging Hex key dogging Less dogging Dogging keys Special center case dogging Double cylinder Electrical options RX Request to exit LX Latchbolt monitoring SS Signal switch CX Chexit® ALK Alarm kit E Electric mortise lock device EL Electric latch retraction QEL Quiet electric latch retraction CON Allegion Connect Electrical accessories Power supplies Electric power transfer Mechanical options XP98/99 rim exit device WS Surface vertical rod exit device Less bottom rod AX Accessible device Pullman latch Dummy push pad Braille, embossed, knurled and safety glow (Luminescent) touchpads Pneumatic options Pneumatic controlled exit devices Pneumatic power transfer Device accessories Glass bead kit Vertical rod and latch guard Cover plate kits Cylinders Mullions Sex bolts Additional information ANSI Function, grade & type Ul fire labeling and opening size Finishes Standard & special finishes Symbols Indicates fire rated application Indicates ADA products C o n t i n u i n g c o m m i t m e n t t o q u a l i t y. 4 • Von Duprin 98/99 Series Nomenclature – how to order EL None SD CD CX E QEL EL LX RX RX2 SS AX Standard Special dogging R/VR - panic only Cylinder dogging - panic only Chexit Electric locking mortise/lever Quiet electric latch retraction Electric latch retraction Latch bolt monitoring Request to exit Double request to exit Signal switch Accessible device PL PN WS XP Pullman latch Pneumatic latch retraction Surface vertical rod exit device Heavy protection - rim WS Tornado & hurricane tested 98 99 Series 98-smooth Series 99-grooved None 27 47 47WDC 48 49 49WDC 57 75 Rim device Surface mounted vertical rod device Concealed vertical rod device Concealed vertical rod wood door device Concealed vertical rod device Concealed vertical cable device Concealed vertical cable wood door device Three-point latch device Mortise lock device AD DT EO HL K K-BE K-DT K-NL L L-BE L-DT L-NL NL NL-OP TL TL-BE TP TP-BE AD Trim (to come from client) Dummy trim Exit only Hospital pull trim Knob Knob - blank escutcheon Knob, rigid - dummy trim Knob, rigid - night latch Lever (classroom) Lever - blank escutcheon Lever, rigid - dummy trim Lever, rigid - night latch Night latch Night latch cylinder assembly, optional pull Turn lever Turn lever - blank escutcheon Thumbpiece Thumbpiece - blank escutcheon XX Lever style 06 standard Optional 01, 02, 03, 05, 07, 12 (Handed), 16 (Omega), 17, 18, Accent, Asti, Merano, St. Annes F Fire exit device -2 Double cylinder (rim & mortise only) LBR LBL SG ALK ALK-AR1 ALK-AR3 ALK-AR6 CON Less bottom rod Less bottom latch Safety glow (luminescent) touchpad Alarm kit Auto-reset 1 1 /2 minute alarm kit Auto-reset 3 minute alarm kit Auto-reset 4 1 /2 minute alarm kit Allegion Connect 2' 3' 4' 2' Device (2' door size) 27, 47 or 49 only 3' Device (2' 4"– 3' door size) 4' Device (2' 10"– 4' door size) Finishes US3, US4, US10, US26, US26D, US28, 313, 315 US32D – 98 ONLY -AM Antimicrobial (available US26D and US32D) -LHR -RHR Left hand reverse Right hand reverse 99 27 -L -16 -F LBR 3' US3 RHR Von Duprin 98/99 Series • 5 Popular double door applications Single door applications Double door applications Mortise lock and surface mounted or concealed vertical cable/rod device combination—same direction Single rim device Single mortise lock device Two rim devices with mullion— same direction Two vertical rods—double egress Door handing Left hand-reverse Left Hand-Reverse orientation Right hand-reverse Right Hand-Reverse orientation Orientation Orientation LHR RHR hand reverse) (Left(Left hand-reverse) (Right hand reverse) (Right hand-reverse) Outside Two surface mounted vertical rod devices—same direction (do not use with overlapping astragal) Outside Two fire exit hardware vertical cables/rods with auxilary fire latch-LBR option Two concealed vertical cables/rods Outside trim operation Trim operation lever or knob Standard Night latch Blank escutcheon Dummy Key locks and unlocks lever or knob. e.g., 996L (Classroom) Key retracts latch bolt. Lever or knob is rigid. Use NL suffix, e.g. 996LNL. (Storeroom) Lever or knob always active. Use BE suffix, e.g., 996L-BE. (Passage) Lever or knob rigid for pull operation. Use DT suffix, e.g., 996L-DT. 996L Breakaway™ lever The 996L Breakaway trim has become the standard lever trim offering on the 98L/99L Series devices. The Breakaway design is especially effective in areas where vandalism to door hardware is a problem. The design intent is to discourage costly repairs from becoming necessary. The Breakaway feature is not available on the NL (night-latch) or DT (dummy trim) versions. 6 • Von Duprin 98/99 Series 374T/376T Series thumbturn control Standard operation, key locks and unlocks thumbturn. Optional operation, key unlocks thumbturn, re-locks when key is removed. This operation is created by changing the cylinder plate included with control. Use 1 1/4" mortise cylinder with a straight cam. Schlage cam reference B502-191. Use with a pull trim (990DT pictured). Lever styles Decorative levers M51 Knurling available M52 Knurling available M53 M54 M55 M56 M57 •• M61 (Handed) M62 •• (Handed) M63 (Handed) M81 Knurling available M82 M83 M84 M85 (Handed) •• Available in Stainless Steel substrate ONLY. Standard Levers 01 02 Knurling available 03* Knurling available 05 06* Default lever Knurling available 07 12 (Handed) 16 (Omega) 17* Knurling available 18 ACC (Accent) (Handed) AST (Asti) (Handed) MER (Merano) (Handed) STA (St. Annes) (Handed) LAT* Latitude LON* Longitude *Available in Stainless Steel - specify SS when ordering Von Duprin 98/99 Series • 7 98/99 Rim exit device The 299 Strike ships standard, optional strikes available 98 and 99 Rim exit devices for all types of single and double doors with mullion, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. The 98 device has a smooth mechanism case and the 99 device has a grooved case. The rim device is non-handed except when the following device options are used: SD (special dogging), -2 (double cylinder) or SS (signal switch). See Opposite page for available outside trim and device functions. Covers stock hollow metal doors with 86 or 161 cutouts on single doors (may cover cutouts on pairs – consult template). Hex key dogging comes standard on 98/99 Rim exit devices Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. 98/99 Rim exit device Specifications Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. Device lengths 3' 4' Device centerline from finished floor 39 13/16" (1011 mm) 39 11/16" (1008 mm) with mullion Center case dimensions 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) Mechanism case dimensions 2 1/4" x 2 1/4" (57mm x 57mm) Projection Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking, 3/4" (19mm) throw Fasteners & sex bolts (SNB) Includes screw pack for 1 3/4" (44mm) and 2 1/4" (57mm) thick metal or wood doors. Optional 425 SNB available, see page 9 for quantities. Electric options LX RX RX2 E EL QEL SS CX ALK WP-RX CON Latchbolt monitor switch Pushpad monitor switch Double pushpad monitor switch Electric locking & unlocking trim Electric latch retraction Quiet electric latch retraction Signal switch Chexit delayed exit Alarm exit kit Waterproof request to exit Allegion Connect -2 AX GBK PN XP SNB SEC Double cylinder Accessible device Glass bead kit Pneumatic latch retraction Extra protection Sex bolts Security screws Mechanical options 2'4' to 3' (711mm to 914 mm) Door size 2'10" to 4' (864 mm to 1219 mm) Door size Dogging feature Hex key dogging standard Dogging options CD SD LD DI CI Strikes 299 – Dull black 8 • Von Duprin 98/99 Series Cylinder dogging Special center case dogging Less dogging Dogging indicator Cylinder dogging indicator XP CD Extra protection • 90˚ latch-tostrike contact • Force resistance of 2,000+ lbs. Cylinder dogging • Replaces hex key dogging • Requires 1 1/4" mortise cylinder with inverted cam QEL RX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad CX AX Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Accessible device • UL certified to meet new 5 lb. maximum operating force requirement • Exceeds ANSI/ BHMA requirements EL ALK Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key PN CON Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply Standard trim EO DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required 98EO 99EO 98DT 99DT 98NL 99NL 98NL-OP 99NL-OP — 990DT 990NL-R/V 110NL-MD 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — Pull center to center — 5 /2" (140mm) 5 /2" (140mm) — Projection 2" (51mm) 2" (51mm) — Product description Trim description Escutcheon plate size — 1 1 ANSI function 01 02 03 03 Cylinder type — — Rim Rim — — — — x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 98L 99L 98L-NL 99L-NL 98L-BE 99L-BE 98L-DT 99L-DT Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Optional #425 SNB quantity for device Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 98/99 Rim exit device Handing Optional trim * Electrified lever operation available Notes Von Duprin 98/99 Series • 9 98-F/99-F Rim exit device The 299F Strike ships standard, optional strikes available 98-F and 99-F Rim fire exit devices for all types of single doors up to 4' x 10' (1219mm x 3048mm) or 8' x 10' (2438mm x 3048mm) double doors with 9954 or 9854 mullion, UL listed for fire exit hardware. See page 68 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2008 Grade 1. The 98-F device has a smooth mechanism case and the 99-F device has a grooved case. The rim device is non-handed except when the following device options are used: -2 (double cylinder) or SS (signal switch). See opposite page for available outside trim and device functions. Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. 98-F/99-F Rim exit device Specifications Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. Device lengths 3' 4' Device centerline from finished floor 39 13/16" (1011 mm) 39 11/16" (1008 mm) with mullion Center case dimensions 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) Mechanism case dimensions 2 /4" x 2 /4" (57mm x 57mm) Projection Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking, 3/4" (19mm) throw Fasteners & sex bolts (SNB) Includes screw pack for 1 3/4" (44mm) and 2 1/4" (57mm) thick metal or wood doors. Optional 425 SNB available for metal doors. 425 & 825 SNB required on wood doors without SLM blocking. See page 11 for quantities. Electric options LX RX RX2 E EL QEL SS CX ALK WP-RX CON Latchbolt monitor switch Pushpad monitor switch Double pushpad monitor switch Electric locking & unlocking trim Electric latch retraction Quiet electric latch retraction Signal switch Chexit delayed exit Alarm exit kit Waterproof request to exit Allegion Connect -2 AX GBK PN XP SNB SEC SLM Double cylinder Accessible device Glass bead kit Pneumatic latch retraction Extra protection Sex bolts Security screws Special Laminate Material Blocking Mechanical options 1 2'4' to 3' (711mm to 914 mm) Door size 2'10" to 4' (864 mm to 1219 mm) Door size 1 Dogging option No mechanical dogging. EL and QEL option available Strikes 299F – Dull black, 499F with mullions 10 • Von Duprin 98/99 Series 499F Strike with 9854/9954 mullion XP RX Extra protection • 90˚ latch-tostrike contact • Force resistance of 2,000+ lbs. Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad EL ALK Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key QEL CX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm AX SG Accessible device • UL certified to meet new 5 lb. maximum operating force requirement • Exceeds ANSI/ BHMA requirements Safety glow • Shows exit door location in darkness or smoke • Developed to meet MEA standards PN CON Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply Standard trim EO DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required 98EO-F 99EO-F 98DT-F 99DT-F 98NL-F 99NL-F 98NL-OP-F 99NL-OP-F — 990DT 990NL-R/V 110NL-MD 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — Pull center to center — 5 /2" (140mm) 5 /2" (140mm) — Projection 2" (51mm) 2" (51mm) — Product description Trim description Escutcheon plate size — 1 1 ANSI function 01 02 03 03 Cylinder type — — Rim Rim — — — — x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL #425 SNB optional - HMD req. WD w/o SLM pkg. 2 2 2 2 #825 SNB req. WD w/o SLM pkg. 2 (if using trim) 2 2 2 #425 SNB req. w/ 499F 2 2 2 2 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged (not recommended for fire device) 98L-F 99L-F 98L-NL-F 99L-NL-F 98L-BE-F 99L-BE-F 98L-DT-F 99L-DT-F Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description 98-F/99-F Rim exit device Handing Optional trim Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible #425 SNB optional - HMD req. WD w/o SLM pkg. 2 2 2 2 #825 SNB req. WD w/o SLM pkg. 2 (if using trim) 2 2 2 #425 SNB req. w/ 499F 2 2 2 2 * Electrified lever operation available Von Duprin 98/99 Series • 11 9875/9975 Mortise lock device 7500 Mortise Lock 9875/9975 Mortise lock device for all types of single or double doors, UL listed for Panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. Fits stock hollow metal doors with 86 cutout and door stiles as narrow as 4 3/4" (121mm). The 9875 device has a smooth mechanism case and the 9975 device has a grooved case. The mortise lock device is non-handed except when the following device options are used: -2 (double cylinder) or SS (signal switch). See opposite page for available outside trim and device functions. 575 Strike Hex key dogging comes standard on 9875/9975 Mortise Lock Devices 9875/9975 Mortise lock device The 7500 Mortise lock is equipped with a 3/4" (19mm) anti-friction latch bolt which is field reversible without removing the lock from the door. It has a non-handed auxiliary bolt for deadlocking and a faceplate with an adjustable bevel. Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. Device lengths 3' 4' Device centerline from finished floor 39 13/16" (1011 mm) 39 11/16" (1008 mm) with mullion Center case dimensions 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) Mechanism case dimensions 2 1/4" x 2 1/4" (57mm x 57mm) Projection Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Fasteners & sex bolts (SNB) Includes screw pack for 1 3/4" (44mm) and 2 1/4" (57mm) thick metal or wood doors. Optional 425 SNB available, see page 13 for quantities. Electric options RX RX2 E EL QEL SS CX ALK WP-RX CON Pushpad monitor switch Double pushpad monitor switch Electric locking & unlocking trim Electric latch retraction Quiet electric latch retraction Signal switch Chexit delayed exit Alarm exit kit Waterproof request to exit Allegion Connect Mechanical options -2 GBK PN SNB SEC Double cylinder Glass bead kit Pneumatic latch retraction Sex bolts Security screws Dogging feature Hex key dogging standard Dogging option CD SD LD DI CI Strikes 575 – Dull Black 12 • Von Duprin 98/99 Series 2'4' to 3' (711mm to 914 mm) Door size 2'10" to 4' (864 mm to 1219 mm) Door size Cylinder dogging Special center case dogging Less dogging Dogging indicator Cylinder dogging indicator QEL CD Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Cylinder dogging • Replaces hex key dogging • Requires 1 1/4" mortise cylinder with inverted cam CX RX Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad EL ALK Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key E (E7500) CON Electric mortise lock device • Remains latched while unlocked • Remote electrical control Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply PN SS 7500 Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Signal switch • Signals unauthorized use of an opening • Switch makes latch bolt tamper-resistant Standard trim EO DT NL HL No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Hospital latch Key locks & unlocks Product description 9875EO 9975EO 9875DT 9975DT 9975NL 9875NL 9875HL Trim description — 990DT 990NL-M HL6M — 3" x 14 3/16" x 3/32" (76x360x2mm) 3" x 14 3/16" x 3/32" (76x360x2mm) 2 9/16" x 5 1/2" x 2 5/8" (65x140x67mm) Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) – Projection 2" (51mm) 2" (51mm) 2 5/8" (67mm) Escutcheon plate size — 9975HL 01 02 03 — — — 1 1/4" Mortise 1 1/4" Mortise x990EO x996EO x996K-DT x996L-DT) x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 2 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9875L 9975L 9875L-NL 9975L-NL 9875L-BE 9975L-BE 9875L-DT 9975L-DT Trim description 996L-M* 996L-NL-M 996L-BE-M* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Handing Optional trim Optional #425 SNB quantity for device Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type 1 1/4" Mortise 1 1/4" Mortise — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 9875/9975 Mortise lock device ANSI function Cylinder type * Electrified lever operation available Notes Von Duprin 98/99 Series • 13 9875-F/9975-F Mortise lock fire exit device 9875-F/9975-F Mortise lock fire exit device 9875-F/9975-F Fire exit mortise lock devices for all types of single doors up to 4' x 10' (1219mm x 3048mm) or 8' x 10' (2438mm x 3048mm) double doors installations, UL listed for fire exit hardware; See page 68 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2008 Grade 1. Fits door stiles as narrow as 4 3/4" (121mm). The 9875-F device has a smooth mechanism case and the 9975-F device has a grooved case. The mortise lock device is non-handed except when the following device options are used: -2 (double cylinder) or SS (signal switch) devices. See opposite page for available outside trim and functions. 7500 Mortise Lock 575 Strike The 7500 Mortise lock is equipped with 3/4" (19mm) anti-friction latch bolt which is field reversible without removing the lock from the door. It has a non-handed auxiliary bolt for deadlocking and a faceplate with an adjustable bevel. Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw. Device lengths 3' 4' Device centerline from finished floor 39 13/16" (1011 mm) 39 11/16" (1008 mm) with mullion Center case dimensions 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) Mechanism case dimensions 2 1/4" x 2 1/4" (57mm x 57mm) Projection Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Fasteners & sex bolts (SNB) Includes screw pack for 1 3/4" (44mm) and 2 1/4" (57mm) thick metal or wood doors. Optional 425 SNB available for metal doors. 425 & 825 SNB required on wood doors without SLM blocking. See page 11 for quantities. 2'4' to 3' (711mm to 914 mm) Door size 2'10" to 4' (864 mm to 1219 mm) Door size RX RX2 E EL QEL SS CX ALK WP-RX CON Pushpad monitor switch Double pushpad monitor switch Electric locking & unlocking trim Electric latch retraction Quiet electric latch retraction Signal switch Chexit delayed exit Alarm exit kit Waterproof request to exit Allegion Connect Mechanical options -2 GBK PN SNB SEC SLM Double cylinder Glass bead kit Pneumatic latch retraction Sex bolts Security screws Special Laminate Material Blocking Dogging option No Mechanical Dogging. EL and QEL option available Strikes 575 – Dull Black Electric options 14 • Von Duprin 98/99 Series QEL RX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad CX ALK Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL SG Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Safety glow • Shows exit door location in darkness or smoke • Developed to meet MEA standards E (E7500) SS 7500 Electric mortise lock device • Remains latched while unlocked • Remote electrical control Signal switch • Signals unauthorized use of an opening • Switch makes latch bolt tamper-resistant PN CON Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply Standard trim DT NL HL No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Hospital latch Key locks & unlocks Product description 9875EO-F 9975EO-F — — 9875NL-F 9975NL-F 9875HL-F 9975HL-F Trim description — 990DT 990NL-M HL6M — 3" x 14 3/16" x 3/32" (76x360x2mm) 3" x 14 3/16" x 3/32" (76x360x2mm) 2 9/16" x 5 1/2" x 2 5/8" (65x140x67mm) Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) – Projection 2" (51mm) 2" (51mm) 2 5/8" (67mm) Escutcheon plate size — ANSI function 01 02 03 — Cylinder type — — 1 1/4" Mortise 1 1/4" Mortise x990EO x996EO x996K-DT x996L-DT) x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 2 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged (not recommended for fire device) 9875L-F 9975L-F 9875L-NL-F 9975L-NL-F 9875L-BE-F 9975L-BE-F — — Trim description 996L-M* 996L-NL-M 996L-BE-M* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Handing Optional trim Optional #425 SNB quantity for device Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type 1 1/4" Mortise 1 1/4" Mortise — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 9875-F/9975-F Mortise lock fire exit device EO * Electrified lever operation available Notes Von Duprin 98/99 Series • 15 9827/9927 Surface mounted vertical rod device Top latch 299 Top strike 9827/9927 Surface mounted vertical rod device 9827/9927 Surface mounted vertical rod device for all types of single or double doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. Covers stock hollow metal doors with 86 or 161 cutouts. The 9827 device has a smooth mechanism case and the 9927 device has a grooved case. The surface vertical rod device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and functions.Vertical rod and latch guards are available to protect the bottom rod of the exit device from damage by impacts of carts or gurneys passing through doors. 248L4 Bottom Strike for use with flat threshold Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) 2 1/4" x 2 1/4" (57mm x 57mm) Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking anti-friction top & bottom bolt, 5/8" (16mm) throw Door undercut 1 Top & bottom Latch case Vertical rods 4 /2" x 2 /8" x 1 /2" (114mm x 54mm x 38mm) Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging feature Dogging option Strikes 16 • Von Duprin 98/99 Series /4" (7mm) recommended 1 1 1 /2" square tubing, standard rods accommodate 7' (2134mm) doors. Top rod length: 34 15/16" (887mm); Bottom rod length: 31 1/2" (794mm) Extension rods available in 1' (205mm) or 3' (914mm) for doors over 7'. One piece top rod is available for 8' (2438mm) and 10' (3048mm) doors. Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick metal or wood doors, and 325 SNB for top and bottom latch. Optional 425 SNB available. LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit PN Pneumatic latch retraction LBR Less bottom rod WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PL Pullman latch WS Tornado and hurricane tested SNB Sex bolts SEC Security screws Hex key dogging standard CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Top - 299 – Dull black, Bottom – 248L4 & 304L - Unfinished 1 304L Bottom strike Bottom latch Hex key dogging comes standard on 9827/9927 WS RX Windstorm • Severe weather certified/tested • FEMA and ICC compliant • Tornado & hurricane tested Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad QEL CON Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply EL ALK Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key E (E996L) CX Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm PN SS Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Signal switch • Signals unauthorized use of an opening • Switch makes latch bolt tamper-resistant Standard trim EO DT NL NL-OP TL TL-BE Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) 9827EO 9927EO 9827DT 9927DT 9827NL 9927NL 9827NL-OP 9927NL-OP 9827TL 9927TL 9827TL-BE 9927TL-BE — 990DT 990NL-R/V 110NL-MD 110NL-WD 374T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 1 11/16" x 7 1/2" x 7/8" (43x191x22mm) 1 11/16" x 7 1/2" x 7/8" (43x191x22mm) Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) — — — Projection — 2" (51mm) 2" (51mm) — 3 1/4" (83mm) 3 1/4" (83mm) ANSI function 01 02 03 03 11 or 12 16 Cylinder type — — Rim Rim 1 1/4" Mortise — Handing — — — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 2 2 Product description Trim description Escutcheon plate size Optional #425 SNB quantity for device L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9827L 9927L 9827L-NL 9927L-NL 9827L-BE 9927L-BE 9827L-DT 9927L-DT Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 9827/9927 Surface mounted vertical rod device No outside trim Exit only Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) * Electrified lever operation available Notes Von Duprin 98/99 Series • 17 9827-F/9927-F Surface Mounted Vertical Rod Fire Device Top latch 9827-F/9927-F Surface mounted vertical rod device 299 Top strike 9827-F/9927-F Fire exit surface mounted vertical rod device pairs of doors up to 8' x 10' (2438mm x 3048mm) , UL listed for fire exit hardware. See page 68 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2008 Grade 1. The 9827-F device has a smooth mechanism case and the 9927-F device has a grooved case. The surface vertical rod device is non-handed except when the following device options are used: SS (signal switch). See opposite page for available outside trim and device functions. Vertical rod and latch guards are available to protect the bottom rod of the exit device from damage by impacts of carts or gurneys passing through doors. Rod and latch guards can be used on hollow metal or tin clad composite fire doors. Finishes – US3, US4, US10, US26, US26D, US28 & 313. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) 2 1/4" x 2 1/4" (57mm x 57mm) Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking anti-friction top & bottom bolt, 5/8" (16mm) throw Door undercut 1 Top & bottom Latch case Vertical rods 4 1/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm) Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging option Strikes 18 • Von Duprin 98/99 Series /4" (7mm) recommended /2" square tubing, standard rods accommodate 7' (2134mm) doors. Top rod length: 34 15/16" (887mm); Bottom rod length: 31 1/2" (794mm) Extension rods available in 1' (205mm) or 3' (914mm) for doors over 7'. One piece top rod is available for 8' (2438mm) and 10' (3048mm) doors. Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick metal or wood doors, and 325 SNB for top and bottom latch. Optional 425 SNB available. LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction LBR Less bottom rod PL Pullman latch WS Tornado and hurricane tested SNB Sex bolts SEC Security screws SLM Special laminate material blocking No mechanical dogging. EL and QEL option available Top – 299F (499F LBR) Dull black, Bottom – 304L - Unfinished 1 499F Top strike - LBR 304L Bottom strike Bottom latch WS RX Windstorm • Severe weather certified/tested • FEMA and ICC compliant • Tornado & hurricane tested Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad QEL ALK Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL CX Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm E (E996L) LBR Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Less bottom rod • Available with UL Fire Label • For pairs of vertical rod devices PN CON Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply Standard trim TL-BE Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) 9827NL-F 9927NL-F 9827NL-OP-F 9927NL-OP-F 9827TL-F 9927TL-F 9827TL-BE-F 9927TL-BE-F 990DT 990NL-R/V 110NL-MD 110NL-WD 374T X 990DT 374T-BE X 990DT 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 1 11/16" x 7 1/2" x 7/8" (43x191x22mm) 1 11/16" x 7 1/2" x 7/8" (43x191x22mm) Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) — — — Projection — 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm) ANSI function 01 02 03 03 11 or 12 16 Cylinder type — — Rim Rim 1 1/4" Mortise — Handing — — — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 2 2 Trim description Escutcheon plate size Optional #425 SNB quantity for device DT NL No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt 9827EO-F 9927EO-F — — — — NL-OP L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged (not recommended for fire device) 9827L-F 9927L-F 9827L-NL-F 9927L-NL-F 9827L-BE-F 9927L-BE-F — — Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 9827-F/9927-F Surface mounted vertical rod device TL Product description EO * Electrified lever operation available Notes Von Duprin 98/99 Series • 19 9857/9957 Three-point latching device Top latch 299 Top & middle strike 9857/9957 Three-point latching device for all types of single or double doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. Covers stock hollow metal doors with 86 or 161 cutouts. The 9857 device has a smooth mechanism case and the 9957 device has a grooved case. The three-point latching device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and functions. Vertical rod and latch guards are available to protect the bottom rod of the exit device from damage by impacts of carts or gurneys passing through doors. 248L4 Bottom Strike for use with flat threshold 9857/9957 Three-point latching device Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection Latch bolt Door undercut Top & bottom Latch case Vertical rods Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging feature Dogging option Strikes 20 • Von Duprin 98/99 Series 304L Bottom strike Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 3913/16" (1011 mm) 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) 2 1/4" x 2 1/4" (57mm x 57mm) Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Deadlocking anti-friction top & bottom bolt, 5/8" (16mm) throw Deadlocking rim bolt, 3/4" (19mm) throw 1 /4" (7mm) recommended 4 1/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm) /2" square tubing, standard rods accommodate 7' (2134mm) doors. Top rod length: 34 15/16" (887mm); Bottom rod length: 31 1/2" (794mm) Extension rods available in 1' (205mm) or 3' (914mm) for doors over 7'. One piece top rod is available for 8' (2438mm) and 10' (3048mm) doors. Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick metal or wood doors, and 325 SNB for top and bottom latch. Optional 425 SNB available. LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction PL Pullman latch WS Tornado and hurricane tested SNB Sex bolts SEC Security screws Hex key dogging standard CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Top & middle – 299 - Dull black Bottom – 248L4 & 304L - Unfinished 1 Bottom latch Hex key dogging comes standard on 9857/9957 Three-point latching devices WS CON Windstorm • Severe weather certified/tested • FEMA and ICC compliant • Tornado & hurricane tested Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply PN ALK Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL RX Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad E (E996L) LX Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt QEL SS Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Signal switch • Signals unauthorized use of an opening • Switch makes latch bolt tamper-resistant Standard trim EO DT NL NL-OP TL TL-BE No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) 9857EO 9957EO 9857DT 9957DT 9857NL 9957NL 9857NL-OP 9957NL-OP 9857TL 9957TL 9857TL-BE 9957TL-BE — 990DT 990NL-R/V 110NL-MD 110NL-WD 374T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" — (76x360x2mm) Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) — — — Projection 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm) Product description Trim description Escutcheon plate size ANSI function 01 02 03 03 11 or 12 16 Cylinder type — — Rim Rim 1 1/4" Mortise — Handing — — — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 2 2 Optional #425 SNB quantity for device L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9857L 9957LF 9857L-NL 9957L-NL 9857L-BE 9957L-BE — — Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 9857/9957 Three-point latching device — 2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) (70x273x21mm) * Electrified lever operation available Notes Von Duprin 98/99 Series • 21 9857-F/9957-F Three-point latching fire exit device Top latch 9857-F/9957-F Three-point latching fire exit device 299 Top & middle strike 9857-F/9957-F Fire exit three-point latching device for all types of single doors up to 4' x 8' (1219mm x 2438mm) or up to 8' x 8'(2438mm x 2438mm) double doors with 9954 or 9854 mullion, UL listed for fire exit hardware. See page 68 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2008 Grade 1. The 9857-F device has a smooth mechanism case and the 9957-F device has a grooved case. The three-point latch device is non-handed except when the following device option is used: SS (signal switch). See opposite page for available outside trim and device functions. Vertical rod and latch guards are available to protect the bottom rod of the exit device from damage by impacts of carts or gurneys passing through doors. Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection Latch bolt Door undercut Top & bottom Latch case Vertical rods Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging option Strikes 22 • Von Duprin 98/99 Series Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 3913/16" (1011 mm) 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) 2 1/4" x 2 1/4" (57mm x 57mm) Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Deadlocking anti-friction top & bottom bolt, 5/8" (16mm) throw Deadlocking rim bolt, 3/4" (19mm) throw 1 /4" (7mm) recommended 4 1/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm) /2" square tubing, standard rods accommodate 7' (2134mm) doors. Top rod length: 34 15/16" (887mm); Bottom rod length: 31 1/2" (794mm) Extension rods available in 1' (205mm) or 3' (914mm) for doors over 7'. One piece top rod is available for 8' (2438mm) and 10' (3048mm) doors. Includes screw pack for 13/4" (44mm) and 2 1/4" (57mm) thick metal or wood doors, and 325 SNB for top and bottom latch. Optional 425 SNB available for metal doors. 425 SNB required on wood doors without SLM blocking. LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction SNB Sex bolts SEC Security screws SLM Special laminate material blocking No mechanical dogging. EL and QEL option available Top & middle – 299 - Dull black Bottom – 304L - Unfinished 304L Bottom strike 499F Rim Strike for Mullion Applications Bottom latch PN RG Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Rod guard • Protection from carts/gurneys • Eases wheelchair access EL QEL Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation E (E996L) LX Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt RX CX Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm ALK CON Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply 1 Standard trim EO DT NL NL-OP TL TL-BE Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) 9857EO-F 9957EO-F 9857DT-F 9957DT-F 9857NL-F 9957NL-F 9857NL-OP-F 9957NL-OP-F 9857TL-F 9957TL-F 9857TL-BE-F 9957TL-BE-F — 990DT 990NL-R/V 110NL-MD 110NL-WD 374T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" — (76x360x2mm) Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) — — — Projection 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm) Product description Trim description Escutcheon plate size — 2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) (70x273x21mm) ANSI function 01 02 03 03 11 or 12 16 Cylinder type — — Rim Rim 1 1/4" Mortise — Handing — — — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL #425 SNB optional - HMD req. WD w/o SLM pkg. 6 2 2 6 2 2 #425 SNB req. w/ 499F 2 2 2 2 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9857L-F 9957L-F 9857L-NL-F 9957L-NL-F 9857L-BE-F 9957L-BE-F — — Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible #425 SNB optional - HMD req. WD w/o SLM pkg. 2 2 2 2 #425 SNB req. w/ 499F 2 2 2 2 9857-F/9957-F Three-point latching fire exit device No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) * Electrified lever operation available Notes Von Duprin 98/99 Series • 23 9847/9947 Concealed vertical rod device Top Latch 338 Top Strike 9847/9947 Concealed vertical rod device for use on single or double metal doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. The 9847 device has a smooth mechanism case and the 9947 device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and device functions. 9847/9947 Concealed vertical rod device Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. 385A Bottom Strike Bottom Latch Specifications Device functions Device lengths Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) Standard Adjustable from 355/8" (905mm) to 495/8" (1260mm) 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) 2 1/4" x 2 1/4" (57mm x 57mm) Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking top & bottom bolt, 5/8" (16mm) throw Door undercut 1 Top & bottom Latch case Vertical rods 4 1/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm) Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging feature Dogging option Strikes 24 • Von Duprin 98/99 Series /4" (7mm) recommended Round 2-piece adjustable rods – Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8" (905 mm) to 49 5/8" (1260 mm). Extension rod kits available for doors over 8'4" (2533mm). Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick metal doors. Optional 425 SNB available. LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction LBR Less bottom rod PL Pullman latch SNB Sex bolts SEC Security screws Hex key dogging standard CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Top – 338 - Unfinished, Bottom – 385A - Unfinished Hex key dogging comes standard on 9847/9947 Concealed vertical rod devices QEL RX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad CX CON Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply EL ALK Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key E (E996L) LX Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt PN DI Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Dogging indicator • Monitor dogging status without a control panel • Red indicator light shows visibility to dogging from over 75 feet Standard trim EO DT NL NL-OP TL TL-BE No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) Product description 9847EO 9947EO 9847DT 9947DT 9847NL 9947NL 9847NL-OP 9947NL-OP 9847TL 9947TL 9847TL-BE 9947TL-BE Trim description — 990DT 990NL-R/V 110NL-MD 376T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" — (76x360x2mm) 2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) (70x273x21mm) 5 1/2" (140mm) 5 1/2" (140mm) — — Escutcheon plate size Pull center to center — — — 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm) ANSI function 01 02 03 03 11 or 12 16 Cylinder type — — Rim Rim 1 1/4" Mortise — Handing — — — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 2 2 Optional #425 SNB quantity for device L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9847L 9947LF 9847L-NL 9947L-NL 9847L-BE 9947L-BE 9847L-DT 9947L-DT Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 9847/9947 Concealed vertical rod device Projection * Electrified lever operation available Notes Von Duprin 98/99 Series • 25 9847-F/9947-F Concealed vertical rod fire exit device Top Latch 9847-F/9947-F Concealed vertical rod fire exit device 338 Top Strike 9847-F/9947-F Fire exit concealed vertical rod device for use on pairs of doors up to 8' x 10' (2438mm x 3048mm) , UL listed for fire exit hardware. See page 68 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2008 Grade 1. The 9847-F device has a smooth mechanism case and the 9947-F device has a grooved case. The concealed vertical rod device is non-handed except when the following device option is used: SS (signal switch) devices. See opposite page for available outside trim and functions. 385A Bottom Strike Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) Standard Adjustable from 355/8" (905mm) to 495/8" (1260mm) Center case dimensions 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) Mechanism case dimensions 2 1/4" x 2 1/4" (57mm x 57mm) Projection Pushbar neutral – 3 /16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) 13 Latch bolt Deadlocking top & bottom bolt, 5/8" (16mm) throw /4" (7mm) recommended Door undercut 1 Top & bottom Latch case 3 3/4" x 1 1/2" x 1" (95mm x 38mm x 25mm) Vertical rods Round 2-piece adjustable rods – Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8" (905 mm) to 49 5/8" (1260 mm). Extension rod kits available for doors over 8'4" (2533mm). Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick metal doors. Optional 425 SNB available. Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging option Strikes 26 • Von Duprin 98/99 Series LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect LBR Less bottom rod PN Pneumatic latch retraction GBK Glass bead kit SNB Sex bolts SEC Security screws SLM Special laminate material blocking No mechanical dogging. EL and QEL option available Top – 338 - Unfinished, Bottom – 385A - Unfinished Bottom Latch PN RG Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Rod guard • Protection from carts/gurneys • Eases wheelchair access EL QEL Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation E (E996L) LX Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt RX CX Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm ALK CON Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply Standard trim EO DT NL NL-OP TL TL-BE Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) Product description 9847EO-F 9947EO-F — — 9847NL-F 9947NL-F 9847NL-OP-F 9947NL-OP-F 9847TL-F 9947TL-F 9847TL-BE-F 9947TL-BE-F Trim description — 990DT 990NL-R/V 110NL-MD 376T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" — (76x360x2mm) 2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) (70x273x21mm) 5 1/2" (140mm) 5 1/2" (140mm) — — Escutcheon plate size Pull center to center — — Projection — 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm) ANSI function 01 02 03 03 11 or 12 16 Cylinder type — — Rim Rim 1 1/4" Mortise — Handing — — — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 2 2 #425 SNB optional - HMD req. WD w/o SLM pkg. L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9847L-F 9947L-F 9847L-NL-F 9947L-NL-F 9847L-BE-F 9947L-BE-F — — Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible #425 SNB optional - HMD req. WD w/o SLM pkg. 2 2 2 2 9847-F/9947-F Concealed vertical rod fire exit device No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) * Electrified lever operation available Notes Von Duprin 98/99 Series • 27 9848/9948 Concealed vertical rod device Top Latch 338 Top Strike 9848/9948 Concealed vertical rod device for use on single or double metal doors, UL listed for panic exit hardware. Covers stock hollow metal doors with 86 or 161 cutouts. Devices are ANSI A156.3 – 2008 Grade 1. The 9848 device has a smooth mechanism case and the 9948 device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used:SD (special dogging), or SS (signal switch). See opposite page for available outside trim and functions. 385A Bottom Strike 9848/9948 Concealed vertical rod device Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Bottom Latch Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) Standard Adjustable from 355/8" (905mm) to 495/8" (1260mm) Center case dimensions 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) Mechanism case dimensions 2 1/4" x 2 1/4" (57mm x 57mm) Projection Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking top bolt, 3/4" (19mm) throw Deadlocking bottom bolt, 1 1/2" (38mm) throw 3 /4" (19mm) maximum, more than 1/4" minimum Door undercut Top & bottom Latch case 4 1/4" x 1 1/2" x 1 1/8" (107mm x 38mm x 28mm) Vertical rods Round 2-piece adjustable rods – Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8" (905 mm) to 49 5/8" (1260 mm). Extension rod kits available for doors over 8'4" (2533mm). Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick metal doors. Optional 425 SNB available. Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging feature Dogging option Strikes 28 • Von Duprin 98/99 Series LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction SNB Sex bolts SEC Security screws Hex key dogging standard CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Top – 338 - Unfinished, Bottom – 385A - Unfinished Hex key dogging comes standard on 9848/9948 Concealed vertical rod devices CX ALK Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL SS Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Signal switch • Signals unauthorized use of an opening • Switch makes latch bolt tamper-resistant QEL LX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt E (E996L) SG Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Safety glow • Shows exit door location in darkness or smoke • Developed to meet MEA standards PN CON Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply Standard trim EO DT NL NL-OP TL TL-BE No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) Product description 9848EO 9948EO 9848DT 9948DT 9848NL 9948NL 9848NL-OP 9948NL-OP 9848TL 9948TL 9848TL-BE 9948TL-BE Trim description — 990DT 990NL-R/V 110NL-MD 374T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" — (76x360x2mm) 2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) (70x273x21mm) Escutcheon plate size 5 1/2" (140mm) 5 1/2" (140mm) — — — — 2" (51mm) 2" (51mm) — 3 /4" (83mm) 3 1/4" (83mm) ANSI function 01 02 03 03 11 — Cylinder type — — Rim Rim 1 1/4" Mortise — Handing — — — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 2 2 Optional #425 SNB quantity for device 1 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9848L 9948LF 9848L-NL 9948L-NL 9848L-BE 9948L-BE 9848L-DT 9948L-DT Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 9848/9948 Concealed vertical rod device Pull center to center — Projection * Electrified lever operation available Notes Von Duprin 98/99 Series • 29 9848-F/9948-F Concealed vertical rod fire exit device Top Latch 9848-F/9948-F Concealed vertical rod fire exit device 338 Top Strike 9848-F/9948-F Concealed vertical rod device for use on pairs of doors up to 8' x 10' (2438mm x 3048mm), UL listed for fire exit hardware. See page 68 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2008 Grade 1. The 9848-F device has a smooth mechanism case and the 9948-F device has a grooved case. The concealed vertical rod device is non-handed except when the following device option is used: SS (signal switch). See opposite page for available outside trim and functions. 385A Bottom Strike Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Bottom Latch Specifications Device functions Device lengths Device centerline from finished floor Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) Standard Adjustable from 355/8" (905mm) to 495/8" (1260mm) Center case dimensions 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) Mechanism case dimensions 2 1/4" x 2 1/4" (57mm x 57mm) Projection Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking top bolt, 3/4" (19mm) throw Deadlocking bottom bolt, 1 1/2" (38mm) throw 3 /4" (19mm) maximum, more than 1/4" minimum Door undercut Top & bottom Latch case 4 1/4" x 1 1/2" x 1 1/8" (107mm x 38mm x 28mm) Vertical rods Round 2-piece adjustable rods – Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8" (905 mm) to 49 5/8" (1260 mm). Extension rod kits available for doors over 8'4" (2533mm). Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick metal doors. Optional 425 SNB available. Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging option Strikes 30 • Von Duprin 98/99 Series LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction SNB Sex bolts SEC Security screws SLM Special laminate material blocking No mechanical dogging. EL and QEL option available Top – 338 - Unfinished, Bottom – 385A - Unfinished CX ALK Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL SS Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Signal switch • Signals unauthorized use of an opening • Switch makes latch bolt tamper-resistant QEL LX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt E (E996L) RX Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad PN CON Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply Standard trim EO DT NL NL-OP TL TL-BE Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) Product description 9848EO-F 9948EO-F — — 9848NL-F 9948NL-F 9848NL-OP-F 9948NL-OP-F 9848TL-F 9948TL-F 9848TL-BE-F 9948TL-BE-F Trim description — 990DT 990NL-R/V 110NL-MD 374T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" — (76x360x2mm) 2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) (70x273x21mm) Escutcheon plate size Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) — — — Projection — 2" (51mm) 2" (51mm) — 3 /4" (83mm) 3 1/4" (83mm) ANSI function 01 02 03 03 11 — Cylinder type — — Rim Rim 1 1/4" Mortise — Handing — — — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 2 2 #425 SNB optional - HMD req. WD w/o SLM pkg. 1 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged (not recommended for fire device) 9848L-F 9948L-F 9848L-NL-F 9948L-NL-F 9848L-BE-F 9948L-BE-F — — Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible #425 SNB optional - HMD req. WD w/o SLM pkg. 2 2 2 2 9848-F/9948-F Concealed vertical rod fire exit device No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) * Electrified lever operation available Notes Von Duprin 98/99 Series • 31 9849/9949 Concealed vertical cable device Top latch 338 Top strike retrofit bracket 9849/9949 Concealed vertical cable device for use on single or double metal doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. The 9849 device has a smooth mechanism case and the 9949 device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and device functions. Center slide 249 Top strike 9849/9949 Concealed vertical cable device Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) 2 1/4" x 2 1/4" (57mm x 57mm) Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking top & bottom bolt, 1/2" (13mm) throw Door undercut /4" (19mm) maximum (24231516 spacer block kit needed for 3/4" undercut) 5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm) Top & bottom latch case Vertical cable Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging feature Dogging option Strikes 3 /32" (6mm) Diameter stainless steel cables 7 Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick metal doors. Optional 425 SNB available. ALK Alarm exit kit CX Chexit delayed exit E Electric unlocking and locking trim EL Electric latch retraction HD-EL Electric latch retraction w/ hex dogging QEL Quiet electric latch retraction * LX Latchbolt monitor switch RX2 Double pushpad monitor switch RX996L Trim monitor switch RX Pushpad monitor switch RXLC Pushpad monitor switch - low current SS Signal switch WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit LBL Less bottom latch AX Accessible device (LBL only) PN Pneumatic latch retraction SEC Security screws SG Safety glow SNB Sex bolts Hex key dogging standard CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Top - 249 – Unfinished, Bottom – 349 - Unfinished *For 98/9949 devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor latchbolt condition. 32 • Von Duprin 98/99 Series 349 Bottom strike Bottom latch Hex key dogging comes standard on 9849/9949 concealed vertical cable devices CX RX Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad EL ALK Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key AX CON Accessible device • UL certified to meet new 5 lb. maximum operating force requirement • Exceeds ANSI/ BHMA requirements Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply PN DI Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Dogging indicator • Monitor dogging status without a control panel • Red indicator light shows visibility to dogging from over 75 feet CD QEL Cylinder dogging • Replaces hex key dogging • Requires standard 1 1/4" mortise cylinder Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Standard trim EO DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9849EO 9949EO 9849DT 9949DT 9849NL 9949NL 9849NL-OP 9949NL-OP Trim description — 990DT 990NL-R/V 110NL-MD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate size Pull center to center — — 2" (51mm) 2" (51mm) — ANSI function 01 02 03 03 Cylinder type — — Rim Rim Handing — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9849L 9949L 9849L-NL 9949L-NL 9849L-BE 9949L-BE 9849L-DT 9949L-DT Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Optional #425 SNB quantity for device Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 9849/9949 Concealed vertical cable device Projection * Electrified lever operation available Standard door opening height Feet Inches 6'8" 80" 7' 84" 8' 96" 9' 108" 10' 120" Door opening height is measured from finished floor to frame rabbet on door side. See table on left for standard offering. Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011. Von Duprin 98/99 Series • 33 9849-F/9949-F Concealed vertical cable fire exit device Top latch 9848-F/9948-F Concealed vertical rod fire exit device 338 Top strike retrofit bracket 9849/9949 Concealed vertical cable device for use on single or double metal doors, UL listed for panic exit hardware. See page 68 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2008 Grade 1. The 9849 device has a smooth mechanism case and the 9949 device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and device functions. Center slide 249 Top strike Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. 349 Bottom strike Specifications Device functions Device lengths Device centerline from finished floor Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) Standard Center case dimensions 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) Mechanism case dimensions 2 1/4" x 2 1/4" (57mm x 57mm) Projection Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Bottom latch CX SS Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Signal switch • Signals unauthorized use of an opening • Switch makes latch bolt tamper-resistant EL RX Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad Latch bolt Deadlocking anti-friction top & bottom bolt, 5/8" (16mm) throw Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Door undercut /4" (19mm) maximum (24231516 spacer block kit needed for 3/4" undercut) 5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm) QEL E (E996L) Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition AX CON Accessible device • UL certified to meet new 5 lb. maximum operating force requirement • Exceeds ANSI/ BHMA requirements Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply Top & bottom Latch case 3 /32" (6mm) Diameter stainless steel cables Vertical cable 7 Fasteners & sex bolts (SNB) Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick metal doors. Optional 425 SNB available. Electric options ALK Alarm exit kit CX Chexit delayed exit E Electric unlocking and locking trim EL Electric latch retraction HD-EL Electric latch retraction w/ hex dogging QEL Quiet electric latch retraction * LX Latchbolt monitor switch RX2 Double pushpad monitor switch RX996L Trim monitor switch RX Pushpad monitor switch RXLC Pushpad monitor switch - low current SS Signal switch WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit LBL Less bottom latch AX Accessible device (LBL only) PN Pneumatic latch retraction SEC Security screws SG Safety glow SNB Sex bolts No mechanical dogging. EL and QEL option available Top – 249 - Unfinished, Bottom – 349 - Unfinished Mechanical options Dogging option Strikes 34 • Von Duprin 98/99 Series PN Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging *For 98/9949 devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor latchbolt condition. Standard trim DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9849EO-F 9949EO-F — — 9849NL-F 9949NL-F 9849NL-OP-F 9949NL-OP-F Trim description — 990DT 990NL-R/V 110NL-MD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate size Pull center to center — Projection — 2" (51mm) 2" (51mm) — ANSI function 01 02 03 03 Cylinder type — — Rim Rim Handing — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged (not recommended for fire device) 9849L-F 9949L-F 9849L-NL-F 9949L-NL-F 9849L-BE-F 9949L-BE-F — — Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Optional #425 SNB quantity for device Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 9848-F/9948-F Concealed vertical rod fire exit device EO * Electrified lever operation available Standard door opening height Feet Inches 6'8" 80" 7' 84" 8' 96" 9' 108" 10' 120" Door opening height is measured from finished floor to frame rabbet on door side. See table on left for standard offering. Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011. Von Duprin 98/99 Series • 35 9847WDC/9947WDC Wood door concealed vertical rod device Top Latch 9847WDC/9947WDC Wood door concealed vertical rod device 338 Top Strike 9847WDC/9947WDC Concealed vertical rod device for use on single or double wood doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. The 9847WDC device has a smooth mechanism case and the 9947WDC device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and functions. Scalp plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to rods. 385A Bottom Strike Note: Do not use on pair of doors with 9875/9975. Finishes – US3, US4, US10, US26, US26D, US28 & 313. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) Standard Adjustable from 355/8" (905mm) to 495/8" (1260mm) Center case dimensions 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) Mechanism case dimensions 2 1/4" x 2 1/4" (57mm x 57mm) Projection Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking top bolt, 5/8" (16mm) throw Door undercut 1 Top & bottom Latch case 3 /4" x 1 /2" x 1" (95mm x 38mm x 25mm) Vertical rods Round 2-piece adjustable rods – Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8" (905 mm) to 49 5/8" (1260 mm). Extension rod kits available for doors over 8'4" (2533mm). Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick wood doors. 425 SNB required on wood doors without SLM blocking. LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction PL Pullman latch LBR Less bottom rod SNB Sex bolts SEC Security screws Hex key dogging standard Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging feature Dogging option Strikes 36 • Von Duprin 98/99 Series /4" (7mm) maximum 3 1 CD Cylinder dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Top – 338 - Unfinished, Bottom – 385A - Unfinished 283 Top Strike for use with wood frames Bottom Latch Hex key dogging comes standard on 9847/9947 Wood door concealed vertical rod devices CX ALK Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL PL Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Pullman latch • Not for use with Fire Exit Hardware QEL LX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt E (E996L) RX Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad PN CON Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply Standard trim EO DT NL NL-OP TL TL-BE Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) 9847WDC-EO 9947WDC-EO 9847WDC-DT 9947WDC-DT 9847WDC-NL 9947WDC-NL 9847WDCNL-OP 9947WDCNL-OP 9847WDC-TL 9947WDC-TL 9847WDC-TL-BE 9947WDC-TL-BE — 990DT 990NL-R/V 110NL-WD 376TWDC x 990DT 376TWDC-BE x 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" — (76x360x2mm) Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) — — Projection — 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm) ANSI function 01 02 03 03 11 or 12 16 Cylinder type — — Rim Rim 1 1/4" Mortise — — — — 6 2 2 Product description Trim description Escutcheon plate size Handing — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 Optional #425 SNB quantity for device 2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) (70x273x21mm) — L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9847WDC-L 9947WDC-L 9847WDC-L-NL 9947WDC-L-NL 9847WDC-L-BE 9947WDC-L-BE 9847WDC-L-DT 9947WDC-L-DT Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 9847WDC/9947WDC Wood door concealed vertical rod device No outside trim Exit only Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) * Electrified lever operation available Notes Von Duprin 98/99 Series • 37 9847WDC-F/9947WDC-F Wood door concealed vertical rod fire device Top Latch 9847WDC-F/9947WDC-F Wood door concealed vertical rod fire device 338 Top Strike 9847WDC-F/9947WDC-F Fire exit concealed vertical rod device for use on pairs of doors up to 8'0" x 9' 3" (2438mm x 2819mm) double wood doors, UL listed for fire exit hardware. See page 68 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2008 Grade 1. The 9847WDC-F device has a smooth mechanism case and the 9947WDC-F device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used: SS (signal switch). See Opposite page for available outside trim and functions. Scalp Plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to rods. Note: Do not use on pair of doors with 9875-F/9975-F. Finishes – US3, US4, US10, US26, US26D, US28 & 313. US15 and US32D available with 98 Series only. Specifications Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. Device lengths 2' 3' 4' Device centerline from finished floor 395/8" (1006 mm) Standard Center case dimensions 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) Mechanism case dimensions 2 1/4" x 2 1/4" (57mm x 57mm) Projection Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) 2" (610 mm) Door size (shipped less UL label) 2'4' to 3' (711mm to 914 mm) Door size 2'10" to 4' (864 mm to 1219 mm) Door size Latch bolt Deadlocking top & bottom bolt, 5/8" (16mm) throw 385A Bottom Strike 283 Top Strike for use with wood frames Bottom Latch CX ALK Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL LX Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt Door undercut 1 Top & bottom Latch case 3 3/4" x 1 1/2" x 1" (95mm x 38mm x 25mm) QEL RX Vertical rods Round 2-piece adjustable rods – Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8" (905 mm) to 49 5/8" (1260 mm). Extension rod kits available for doors over 8'4" (2533mm). Fasteners & sex bolts (SNB) Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick wood doors. 425 SNB required on wood doors without SLM blocking. Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad Electric options LX RX RX2 E EL QEL SS CX ALK WP-RX CON Latchbolt monitor switch Pushpad monitor switch Double pushpad monitor switch Electric unlocking and locking trim Electric latch retraction Quiet electric latch retraction Signal switch Chexit delayed exit Alarm exit kit Waterproof request to exit Allegion Connect E (E996L) CON Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply Mechanical options GBK PN PL LBR SNB SEC Glass bead kit Pneumatic latch retraction Pullman latch Less bottom rod Sex bolts Security screws Dogging option No mechanical dogging. EL and QEL option available Strikes Top – 338 - Unfinished, Bottom – 385A - Unfinished 38 • Von Duprin 98/99 Series /4" (7mm) maximum PN Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging Standard trim EO Trim description NL NL-OP TL TL-BE No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) 9847WDC-EO-F 9847WDC-DT-F 9847WDC-NL-F 9847WDCNL-OP-F 9847WDC-TL-F 9847WDC-TL-BE-F 9947WDC-EO-F 9947WDC-DT-F 9947WDC-NL-F 9947WDCNL-OP-F 9947WDC-TL-F 9947WDC-TL-BE-F 110NL-WD 376TWDC x 990DT 376TWDC-BE x 990DT — 990DT 990NL-R/V — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" — (76x360x2mm) Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) — — Projection — 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm) ANSI function 01 02 03 03 11 — Cylinder type — — Rim Rim 1 1/4" Mortise — Handing — — — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x996L-NL x696NL x697NL 6 2 2 6 2 2 Escutcheon plate size #425 SNB optional - HMD req. WD w/o SLM pkg. 2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) (70x273x21mm) — L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9847WDC-L-F 9947WDC-L-F 9847WDC-L-NL-F 9947WDC-L-NL-F 9847WDC-L-BE-F 9947WDC-L-BE-F 9847WDC-L-DT-F 9947WDC-L-DT-F Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible #425 SNB optional - HMD req. WD w/o SLM pkg. 2 2 2 2 9847WDC-F/9947WDC-F Wood door concealed vertical rod fire device Product description DT * Electrified lever operation available Notes Von Duprin 98/99 Series • 39 9849WDC/9949WDC Wood door concealed vertical cable device Top latch 9849WDC/9949WDC Wood door concealed vertical cable device 338 Top strike retrofit bracket 9849WDC/9949WDC Concealed vertical cable device for use on single or double wood doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. The 9847WDC device has a smooth mechanism case and the 9947WDC device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See Opposite page for available outside trim and functions. Scalp Plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to cables. Center slide 249 Top strike Note: Do not use on pair of doors with 9975 devices. Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) 2 1/4" x 2 1/4" (57mm x 57mm) Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking top & bottom bolt. 1 1/2" (38mm) throw Door undercut 3 Top & bottom Latch case Vertical cables 5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm) Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging feature Dogging option Strikes 40 • Von Duprin 98/99 Series 349 Bottom strike Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) Standard /8" undercut (10mm) /32" (6mm) Diameter stainless steel cables 7 Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick wood doors. 425 SNB required on wood doors without SLM blocking. ALK Alarm exit kit CX Chexit delayed exit E Electric unlocking and locking trim EL Electric latch retraction HD-EL Electric latch retraction w/ hex dogging QEL Quiet electric latch retraction * LX Latchbolt monitor switch RX2 Double pushpad monitor switch RX996L Trim monitor switch RX Pushpad monitor switch RXLC Pushpad monitor switch - low current SS Signal switch WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit LBL Less bottom latch PN Pneumatic latch retraction SEC Security screws SG Safety glow SNB Sex bolts Hex key dogging standard CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Top - 249 – Unfinished, Bottom – 349 - Unfinished Bottom latch Hex key dogging comes standard on 9849/9949 Wood door concealed vertical cable devices CX ALK Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL RX Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad QEL LX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt E (E996L) CON Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply PN Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging *For 98/9949 devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor latchbolt condition. Standard trim DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9849WDC-EO 9949WDC-EO 9849WDC-DT 9949WDC-DT 9849WDC-NL 9949WDC-NL 9849WDC-NL-OP 9949WDC-NL-OP Trim description — 990DT 990NL-R/V 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate size Pull center to center — Projection — 2" (51mm) 2" (51mm) — ANSI function 01 02 03 03 Cylinder type — — Rim Rim Handing — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9849WDC-L 9949WDC-L 9849WDC-L-NL 9949WDC-L-NL 9849WDC-L-BE 9949WDC-L-BE 9849WDC-L-DT 9949WDC-L-DT Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Optional #425 SNB quantity for device Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 * Electrified lever operation available 9849WDC/9949WDC Wood door concealed vertical cable device EO Standard door opening height Feet Inches 6'8" 80" 7' 84" 8' 96" 9' 108" 10' 120" Door opening height is measured from finished floor to frame rabbet on door side. See table on left for standard offering. Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011. Von Duprin 98/99 Series • 41 9849WDC-F/9949WDC-F Wood door concealed vertical cable fire device Top latch 9849WDC-F/9949WDC-F Wood door concealed vertical rod fire device 338 Top strike retrofit bracket 9849WDC-F/9949WDC-F Fire exit concealed vertical cable device for use on pairs of doors up to 8'0" x 8' 0" (2438mm x 2438mm) double wood doors, UL listed for fire exit hardware. See page 68 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2008 Grade 1. The 9849WDC-F device has a smooth mechanism case and the 9949WDC-F device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SS (signal switch). See opposite page for available outside trim and functions. Center slide 249 Top strike Scalp Plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to cables. Note: Do not use on pair of doors with 9975 devices. Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) Standard 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) 2 1/4" x 2 1/4" (57mm x 57mm) Pushbar neutral – 3 /16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) 13 Latch bolt Deadlocking top & bottom bolt, 1 1/2" (38mm) throw Door undercut 3 Top & bottom Latch case Vertical cables 5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm) Fasteners & sex bolts (SNB) Electric options Mechanical options Dogging option Strikes 42 • Von Duprin 98/99 Series /8" undercut (10mm) /32" (6mm) Diameter stainless steel cables 7 Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick wood doors. 425 SNB required on wood doors without SLM blocking. ALK Alarm exit kit CX Chexit delayed exit E Electric unlocking and locking trim EL Electric latch retraction HD-EL Electric latch retraction w/ hex dogging QEL Quiet electric latch retraction * LX Latchbolt monitor switch RX2 Double pushpad monitor switch RX996L Trim monitor switch RX Pushpad monitor switch RXLC Pushpad monitor switch - low current SS Signal switch WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit LBL Less bottom latch PN Pneumatic latch retraction SEC Security screws SG Safety glow SNB Sex bolts SLM Special laminate material blocking No mechanical dogging. EL and QEL option available Top – 249 - Unfinished, Bottom – 349 - Unfinished 349 Bottom strike Bottom latch CX ALK Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL LX Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt QEL RX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad E (E996L) CON Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply PN Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging *For 98/9949 devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor latchbolt condition. Standard trim EO DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9849WDC-EO-F 9949WDC-EO-F — — 9849WDC-NL-F 9949WDC-NL-F 9849WDC-NL-OP-F 9949WDC-NL-OP-F Trim description — 990DT 990NL-R/V 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate size Pull center to center — Projection — 2" (51mm) 2" (51mm) — ANSI function 01 02 03 03 Cylinder type — — Rim Rim Handing — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x996L-NL x696NL x697NL 6 2 2 6 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged (not recommended for fire device) 9849WDC-L-F 9949WDC-L-F 9849WDC-L-NL-F 9949WDC-L-NL-F 9849WDC-L-BE-F 9949WDC-L-BE-F — — Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Optional #425 SNB quantity for device Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 * Electrified lever operation available Standard door opening height Feet Inches 6'8" 80" 7' 84" 8' 96" 9' 108" 10' 120" Door opening height is measured from finished floor to frame rabbet on door side. See table on left for standard offering. Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011. Von Duprin 98/99 Series • 43 9850WDC/9950WDC Wood door concealed vertical cable device Top latch 9850WDC/9950WDC Wood door concealed vertical cable device 338 Top strike retrofit bracket 9850WDC/9950WDC Concealed vertical cable device for use on single or double wood doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. The 9850WDC device has a smooth mechanism case and the 9950WDC device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See Opposite page for available outside trim and functions. Scalp Plate – Device is furnished standard with an 15" (381 mm) long scalp plate for easy access to cables. Center slide 249 Top strike Note: Do not use on pair of doors with 9975 devices. Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) 2 1/4" x 2 1/4" (57mm x 57mm) Pushbar neutral – 3 13/16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) Latch bolt Deadlocking top & bottom bolt. 1 1/2" (38mm) throw Door undercut 3 Top & bottom Latch case Vertical cables 5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm) Fasteners & sex bolts (SNB) Electric options Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick wood doors. ALK Alarm exit kit CX Chexit delayed exit E Electric unlocking and locking trim EL Electric latch retraction HD-EL Electric latch retraction w/ hex dogging QEL Quiet electric latch retraction * LX Latchbolt monitor switch RX2 Double pushpad monitor switch RX996L Trim monitor switch RX Pushpad monitor switch RXLC Pushpad monitor switch - low current SS Signal switch WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit LBL Less bottom latch PN Pneumatic latch retraction SEC Security screws SG Safety glow SNB Sex bolts Hex key dogging standard CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Top - 249 – Unfinished, Bottom – 450 - Unfinished Mechanical options Dogging feature Dogging option Strikes 44 • Von Duprin 98/99 Series 450 Bottom strike Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) Standard /4" (19mm) maximum /32" (6mm) Diameter stainless steel cables 7 Bottom latch Hex key dogging comes standard on 9850/9950 Wood door concealed vertical cable devices CX ALK Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL RX Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad QEL LX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt E (E996L) CON Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply PN Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging *For 98/9950WDC devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor latchbolt condition. Standard trim DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9850WDC-EO 9950WDC-EO 9850WDC-DT 9950WDC-DT 9850WDC-NL 9950WDC-NL 9850WDC-NL-OP 9950WDC-NL-OP Trim description — 990DT 990NL-R/V 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate size Pull center to center — Projection — 2" (51mm) 2" (51mm) — ANSI function 01 02 03 03 Cylinder type — — Rim Rim Handing — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x696NL x697NL 6 2 2 6 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged 9850WDC-L 9950WDC-L 9850WDC-L-NL 9950WDC-L-NL 9850WDC-L-BE 9950WDC-L-BE 9850WDC-L-DT 9950WDC-L-DT Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Optional #425 SNB quantity for device Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 * Electrified lever operation available 9850WDC/9950WDC Wood door concealed vertical cable device EO Standard door opening height Feet Cable tolerance 6'8" - 7' 72" - 84" 7'1" - 8' 85" - 96" 8'1" - 9' 97" - 108" 9'1" - 10' 109" - 120" Door opening height is measured from finished floor to frame rabbet on door side. See table on left for standard offering. Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011. Von Duprin 98/99 Series • 45 9850WDC-F/9950WDC-F Wood door concealed vertical cable fire device Top latch 9850WDC-F/9950WDC-F Wood door concealed vertical rod fire device 338 Top strike retrofit bracket 9850WDC-F/9950WDC-F Fire exit concealed vertical cable device for use on pairs of doors up to 8' x 9' 3" (2438mm x 2819mm) double wood doors, UL listed for fire exit hardware. See page 72 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The 9850WDC-F device has a smooth mechanism case and the 9950WDC-F device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SS (signal switch). See opposite page for available outside trim and functions. Center slide 249 Top strike Scalp Plate – Device is furnished standard with an 15" (381 mm) long scalp plate for easy access to cables. Note: Do not use on pair of doors with 9975 devices. Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. Specifications Device functions Device lengths Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size 395/8" (1006 mm) Standard 8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm) 2 1/4" x 2 1/4" (57mm x 57mm) Pushbar neutral – 3 /16" (97 mm) Pushbar depressed – 3 1/16" (78 mm) 13 Latch bolt Deadlocking top & bottom bolt, 1 1/2" (38mm) throw Door undercut 3 Top & bottom Latch case Vertical cables 5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm) Fasteners & sex bolts (SNB) Electric options Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick wood doors. ALK Alarm exit kit CX Chexit delayed exit E Electric unlocking and locking trim EL Electric latch retraction HD-EL Electric latch retraction w/ hex dogging QEL Quiet electric latch retraction * LX Latchbolt monitor switch RX2 Double pushpad monitor switch RX996L Trim monitor switch RX Pushpad monitor switch RXLC Pushpad monitor switch - low current SS Signal switch WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit LBL Less bottom latch PN Pneumatic latch retraction SEC Security screws SG Safety glow SNB Sex bolts SLM Special laminate material blocking No mechanical dogging. EL and QEL option available Top – 249 - Unfinished, Bottom – 450 - Unfinished Mechanical options Dogging option Strikes 46 • Von Duprin 98/99 Series /4" (19mm) maximum /32" (6mm) Diameter stainless steel cables 7 450 Bottom strike Bottom latch CX ALK Chexit delayed exit • Meets NFPA 101 requirements • Self-contained controls, locking, alarm Alarm exit kit • Unauthorized opening triggers 85-decibel horn • Set in armed or disarmed mode by key EL LX Electric latch retraction • Enables remote unlatching • Alternative to manual dogging Latchbolt monitor switch • Signals use of an opening • SPDT switch to monitor latch bolt QEL RX Quiet electric latch retraction • Bolt retraction via switch • Converts exit door to push-pull operation Pushpad monitor switch • Signals use of an opening • SPDT switch to monitor pushpad E (E996L) CON Electrified breakaway lever • Electrified remote locking/unlocking • Standard in fail safe condition Allegion Connectors • Common connectors to connect various door hardware all the way to the power supply PN Pneumatic latch retraction • For areas where electrical devices banned • Special linkage for mechanical or pneumatic dogging *For 98/9950 devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor latchbolt condition. Standard trim EO DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9850WDC-EO-F 9950WDC-EO-F — — 9850WDC-NL-F 9950WDC-NL-F 9850WDC-NL-OP-F 9950WDC-NL-OP-F Trim description — 990DT 990NL-R/V 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate size Pull center to center — Projection — 2" (51mm) 2" (51mm) — ANSI function 01 02 03 03 Cylinder type — — Rim Rim Handing — — — — Optional trim x990EO x996EO x996K-DT x996L-DT x996L-DT x696DT x697DT x996K-NL x996L-NL x996L-NL x696NL x697NL 6 2 2 6 L L-NL L-BE L-DT Lever Key locks & unlocks Lever – night latch Key retracts latchbolt Lever – blank escutcheon Always operable (no cylinder) Lever dummy trim pull when dogged (not recommended for fire device) 9850WDC-L-F 9950WDC-L-F 9850WDC-L-NL-F 9950WDC-L-NL-F 9850WDC-L-BE-F 9950WDC-L-BE-F — — Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) 2 3/4" x 10 3/4" x 27/32" (70x273x21mm) Optional #425 SNB quantity for device Product description Pull center to center — — — — Projection 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) ANSI function 08 03 14 02 Cylinder type Rim Rim — — Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device 2 2 2 2 * Electrified lever operation available Standard door opening height Feet Cable tolerance 6'8" - 7' 72" - 84" 7'1" - 8' 85" - 96" 8'1" - 9' 97" - 108" 9'1" - 10' 109" - 120" Door opening height is measured from finished floor to frame rabbet on door side. See table on left for standard offering. Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011. Von Duprin 98/99 Series • 47 98/99 Optional trim Knob, exit only and thumbpiece trim – 990 & 996K K-NL K Knob Key locks & unlocks Trim 996K description Knob – night latch Key retracts latchbolt 996K-NL K-BE Knob – blank escutcheon Always operable (no cylinder) 996K-BE K-DT Knob – dummy trim Pull when dogged 996K-DT EO Exit only plate 996EO TP Thumbpiece Key locks & unlocks 990TP TP-BE Thumbpiece blank escutcheon Always operable (no cylinder) 990TP-BE EO Exit only plate 990EO Escutcheon 23/4" x 103/4" x 27/32" 23/4" x 103/4" x 27/32" 23/4" x 103/4" x 27/32" 23/4" x 103/4" x 27/32" 23/4" x 103/4" x 27/32" 3" x 143/16" x 3/32" 3" x 143/16" x 3/32" 3" x 143/16" x 3/32" plate size (70x273x21mm) (70x273x21mm) (70x273x21mm) (70x273x21mm) (70x273x21mm) (76x360x2mm) (76x360x2mm) (76x360x2mm) Pull center to center — — — — — 51/2" (140mm) 51/2" (140mm) 51/2" (140mm) Projection 31/4" (83mm) 31/4" (83mm) 31/4" (83mm) 31/4" (83mm) — 2" (51mm) 2" (51mm) Z ANSI function 08 09 14 02 01 05 14 14 Rim or vertical rod Rim device Rim — — — Rim — — Mortise lock 1 1 /4" Mortise device 11/4" Mortise — 11/4" Mortise — — Handing — — — — — — — — #425 SNB optionalHMD req. WD w/o SLM pkg. 2 2 2 2 2 2 2 2 #825 SNB req. WD w/o SLM pkg F 2 Rim device ONLY 2 2 2 2 2 2 2 #425 SNB 2 req. w/499F 2 2 2 2 2 2 2 Trim options Cylinder type 48 • Von Duprin 98/99 Series 98/99 Optional trim Optional trims – 696 DT NL TP TP-BE Dummy trim Pull when dogged (not recomended for fire device) Night latch Key retracts latchbolt Thumbpiece Key locks & unlocks Trim description 696DT 696NL 696TP 696TP-BE Escutcheon plate size 23/4" x 103/4" x 27/32" (70x273x21mm) 23/4" x 103/4" x 27/32" (70x273x21mm) 15/8" x 131/2" x 3/16" (41x343x5mm) 15/8" x 131/2" x 3/16" (41x343x5mm) Pull center to center 51/2" (140mm) 51/2" (140mm) 51/2" (140mm) 51/2" (140mm) Projection 2 /6" (52mm) 2 /6" (52mm) 2 /6" (52mm) 2 1/6" (52mm) ANSI function 02 03 05 15 Rim or vertical rod device — Rim Rim — 1 1 1 Thumbpiece – blank escutcheon Always operable (no cylinder) Cylinder type — 11/4" Mortise 11/4" Mortise — — — — — #425 SNB optional-HMD req. WD w/o SLM pkg. 2 2 2 2 #825 SNB req. WD w/o SLM pkg F Rim device ONLY 2 2 2 2 #425 SNB req. w/499F 2 2 2 2 Trim options Mortise lock device Handing Optional trims – 697 DT NL TP TP-BE (3/4" diameter pull) (19mm) (3/4" diameter pull) (19mm) Dummy trim Pull when dogged (not recomended for fire device) Night latch Key retracts latchbolt Thumbpiece Key locks & unlocks Trim description 697DT 697NL 697TP 697TP-BE Escutcheon plate size 23/4" x 103/4" x 27/32" (70x273x21mm) 23/4" x 103/4" x 27/32" (70x273x21mm) 15/8" x 131/2" x 3/16" (41x343x5mm) 23/4" x 103/4" x 27/32" (70x273x21mm) Pull center to center 51/2" (140mm) 51/2" (140mm) 51/2" (140mm) 51/2" (140mm) Projection 3" (76mm) 3" (76mm) 3" (76mm) 3" (76mm) ANSI function 02 03 05 15 — Rim Rim — Thumbpiece – blank escutcheon Always operable (no cylinder) Cylinder type Rim or vertical rod device Mortise lock device — 11/4" Mortise 11/4" Mortise — Handing — — — — #425 SNB optional-HMD req. WD w/o SLM pkg. 2 2 2 2 #825 SNB req. WD w/o SLM pkg F Rim device ONLY 2 2 2 2 #425 SNB req. w/499F 2 2 2 2 Von Duprin 98/99 Series • 49 98/99 Optional trim HL6 Hospital pull Von Duprin and Glynn-Johnson have collaborated on an exit device trim that answers the problem of accessibility and performance. Using the Von Duprin 98/9975 mortise lock exit device along with the Glynn-Johnson HL6 push/pull latch, Allegion has created an exit device with mortise lock durability that utilizes a fully ADA compliant Pull paddle trim. The 98/9975HL device is available in all standard architectural finishes. Consult the Glynn-Johnson catalog for complete product information. 392-7 Offset pull Trim options The 392-7 Offset pull is 3/4₄" round stainless steel, with a 7" center to center which matches the 98/99 center case. Often used with a night latch operation. 3 1/2" (89mm) offset with 1 1/2₂" (38mm) clearance. Vandal resistant trim: IVES VR910 & VR914 Series VR910 grip coated in black plastisol for softer touch and resilience to temperature extremes. Grip designed for comfortable operation. VR914 grip in all stainless steel. Features: • Stainless steel construction, 11 gauge (0.120" thick) • Finish: US32D, only • Thru-bolts and rugged mounting screws for maximum fastening strength. • Built-in lock protector prevents vandalism to mortise latchbolt (available on certain models). • Extra-tough stainless steel cylinder collar prevents pipe wrench or similar tool from damaging cylinder. Tapered design prevents side impacts from transferring directly to cylinder. Collar spins freely. • Furnished with mounting screws for door thicknesses of 1 3/4" to 2 1/4" Model For use with VR910DT & VR914DT 98/99 Rim or 51/2" (133mm) w vertical rod device x 11" (279mm) h VR910NL & VR914NL 98/99 Rim or 51/2" (133mm) w vertical rod device x 11" (279mm) h VR910M-DT & VR914M-DT 9875/9975 Mortise device 7 1/4" (184mm) w x 11" (279mm) h VR910M-NL & VR914M-NL Handing required 9875/9975 Mortise device 7 1/4" (184mm) w x 11" (279mm) h Size • Meets ANSI/BHMA 156.13, Trim security test and California State Accessibility Standards Title 24. • 1 1/2" (38mm) clearence from grip to door, total projection 1 7/8" (48mm) • Consult the IVES catalog for complete product information. 50 • Von Duprin 98/99 Series 98/99 Optional trim This page intentionally left blank Trim options Von Duprin 98/99 Series • 51 Schlage AD-Series AD-Series adaptable electronic locks Standalone locks are a cost-effective solution for doors that do not require real-time monitoring. The AD-Series standalone solution provides: There are a variety of options that allow you to select the AD-Series electronic lock that’s right for you, and a wide selection of features that can be configured in the field to further customize each opening. When your needs change in the future, the innovative modular design of the AD-Series allows you to easily upgrade the credential reader or networking option, and adapt to emerging technologies using your existing chassis – all without taking the lock off the door. This means that you can be confident that your choice of the AD-Series is right for today, and that your investment will be protected into the future. • Upgradability • Improved credential management • Audit trail reports Schlage offers two AD-Series standalone solutions to fit your environment: AD-200 Access rights are stored on the lock AD-250 Access rights are stored on the magnetic stripe credential Chassis • Cylindrical • Mortise • Mortise deadbolt • Exit trim* Locking functions Credential reader options Trim options Standalone The AD-Series was designed to be the right choice for today, and is ready to adapt to whatever the future holds. • Classroom/Storeroom AD-Series electronic locks are compatible with many different brands and technologies of credentials. • Office • Apartment • Multi-technology (reads 125 kHz prox and 1 3.56 MHz smart) + KEYPAD • Privacy Lever styles • Magnetic stripe (insertion) + KEYPAD Sparta Rhodes Athens Tubular Warm Tone Finishes • Magnetic stripe (swipe) + KEYPAD 605 Bright brass 606 Satin brass 612 Satin bronze 643e Aged bronze Cool Tone Finishes • Keypad Communications options Networked In facilities where increased monitoring and control are needed, a networked solution is essential. The AD-Series networked options feature: 619 Satin nickel 625 626 626AM Bright Satin chrome Satin chrome chrome with antimicrobial Certifications • ANSI/BMHA A156.25 • ADA • ANSI/BHMA Grade 1 • FCC part 15 • Open architecture platform • UL 294 Listed • RoHS • Acceptable reader technology • UL 10C • FIPS 201-1 (AD-301 and AD-401) • Real-time monitoring The AD-Series networked lock is available in either a wireless or hardwired configuration to fit your application needs. AD-300 Networked hardwired locks AD-301 Networked hardwired FIPS 201-1 compliant locks AD-400 Networked wireless locks AD-401 Networked wireless FIPS 201-1 compliant locks 52 • Von Duprin 98/99 Series Complete your system Complete your AD-Series system with readers and credentials, biometric hand geometry readers, system components, HHD programming device and other wireless accessories. *See AD-Series exit trim compatibility Datasheet for complete list of compatability by manufacturer. Schlage CO-Series CO-Series electronic locks from Schlage In the world of standalone electronic locks, nothing compares to the CO-Series from Schlage. And because CO-Series locks offer a wide variety of options, it’s easy to find the right solution for any facility. For openings with a relatively small number of users, we recommend the C0-100. It’s an offline keypad programmable lock. For larger applications try the CO-200 or CO-250. They’re computer programmable locks that can provide audit trails. They also offer dual credential options (card+PIN) that provide an even greater level of security. Compatible The CO-Series was designed to easily integrate into your facility. It can work in conjunction with Schlage and Locknetics electronic locks and offers expanded cylinder, exit device, and credential compatibility. Class CO-100 • Manually programmable • User rights stored on the lock • Keypad only CO-200 (shown) • Computer or manually programmable • User rights stored on the lock CO-250 • Computer programmable • User rights stored on the card Readers • Keypad • Magnetic stripe (swipe) • Proximity • Magnetic stripe plus keypad (swipe) • Proximity plus keypad Lever styles Exit device compatibility * Rim SVR CVR/CVC Mortise Von Duprin 98/99 & 98/99 XP 4 4 4 4 Von Duprin 22/22F 4 4 Falcon 25 4 Sparta *See AD-Series Exit trim compatibility datasheet for complete list of compatability by manufacturer. Rhodes Athens Tubular Chassis Trim options • Cylindrical • Mortise • Mortise deadbolt Cylinder compatibility • Exit Trim Full size Full size FSIC key-in-lever key-in-lever 6 & 7 pin 6 pin 7 pin SFIC 6 & 7 pin Schlage l l l Falcon s Sargent® (10L + 11L full size) s s s Corbin Russwin® s s Yale® (includes Medeco 31*0100 FSIC) s s l = s = Q = • 4 standard off the shelf (AA) batteries Functions Q Best® Power • Classroom/storeroom • Privacy • Office Warm tone finishes s with cylinder or less cylinder options less cylinder only less cylinder, only with Sparta and Rhodes levers Note: See price book for specific configurations 605 606 612 643e Bright brass Satin brass Satin bronze Aged bronze Cool tone finishes Credential compatibility The CO-Series is compatible with many different brands and credential technologies. For customers with an installed base of iButtons®, a combo proximity keyfob with iButton option is available to make an easy transition to proximity technology. 619 Satin nickel 625 626 Bright Satin chrome chrome 626AM Satin chrome with antimicrobial Reliable When it comes to securing your facility, you can’t afford to take chances. CO-Series locks are tested to the highest quality and reliability standards in the industry, including: • NSI/BHMA A156.25 & ANSI/BHMA Grade 1 • UL 294 • UL 10C • ADA Von Duprin 98/99 Series • 53 98/99 Strike/Stile information Device type Standard single door Strike Trim/Stile 990/996 98/99 XP 98/99 98-F/99-F XP98-F/XP99-F Strike options / Dogging options 9875 9975 4 3/8" (111mm) Strike Strike w/mullion* Trim/Stile 299 x 4954 299F 909 Strike Application PL9827/PL9927 Pullman latch 299 (Top) 304L/248-L-4 (Bottom) 9827-F 9927-F 299 (Top) 304L (Bottom) 9847 9947 9848 9948 338 (Top) 385A (Bottom) 338 (Top) 385A (Bottom) 338 (Top) 385A (Bottom) 299F 499F x 9954 304L 4 7/8" (124mm) 4 3/4" (121mm) Trim/Stile — — — — — — — — — — 576A-576B 4 3/4" (121mm) 4 3/4" (121mm) — — 576A-576B 4 3/4" (121mm) 4 3/4" (121mm) 1439 or 1410 3 13/16" (97mm) 3 13/16" (97mm) 299 x 5654 4 7/16" (113mm) 4 1/4" (108mm) 1408 x 5754 3 13/16" (97mm) 3 13/16" (97mm) 1606 3 15/16" 4 1/16" 4 3/8" 1606 x 1654 (103mm) (100mm) (112mm) 4 1/4" (108mm) — — — — 4 3/8" (111mm) — — — 4 1/2" (114mm) — — — 299 (Top) 299F (Middle) 304L (Bottom) — 499F x 9854 — KR9954 575-2 4 3/4" (121mm) 3 13/16" (97mm) — — 4 7/8" (124mm) 3 13/16" (97mm) — — 299 x 4954 1408 x 5754 4 1/4" (108mm) — 4 3/8" (111mm) 4 1/4" (108mm) 3 15/16" 4 1/16" 4 3/8" 1606 x 1654 (103mm) (100mm) (112mm) — 4 1/2" (114mm) 4 7/16" (113mm) 1606 575-2 9857 9957 299 x 5654 3 13/16" (97mm) 4 3/4" (121mm) 299 (Top) 299 (Middle) 304L/284-L (Bottom) 4 3/4" (121mm) 3 13/16" (97mm) 990/996 696/697 1439 or 1410 4 3/4" (121mm) 954 x 9954-XP 4 7/8" (124mm) 4 3/4" (121mm) 990/996 696/697 4 3/8" (111mm) 575 299 (Top) 304L/248-L-4 (Bottom) 4 7/8" (124mm) 696/697 Trim/stile 4 1/2" (114mm) 4 3/4" (121mm) 9827 9927 Latch retraction Trim/Stile 990/996 499F x 9954 575 9847WDC 9947WDC Strike w/ mullion* 909 x 4954-XP 9875-F 9975-F 9847-F 9947-F 9848-F 9948-F Optional double door 909 4 3/4" (121mm) 9857-F 9957-F Optional single door 696/697 299 4 1/2" (114mm) Standard double door Optional strike — — — Application Trim/Stile 990/996 696/697 Single door 3 11/16" (94mm) 3 5/8" (92mm) 990/996 696/697 Two vertical rod devices 3 11/16" (94mm) 3 5/8" (92mm) Vertical rod with Mortise lock device 4 3/4" (121mm) 4 3/4" (121mm) Two vertical rods 4 1/4" (108mm) 4 1/8" (105mm) Vertical rod with Mortise lock device 4 3/4" (121mm) 4 3/4" (121mm) Single door 4 1/4" (108mm) 4 1/4" (108mm) Single door Two vertical rod devices 4 1/4" (108mm) 4 1/4" (108mm) 304L Two vertical 4 1/4" 4 1/4" rod devices (108mm) (108mm) Vertical rod with Mortise lock device 4 3/4" (121mm) 4 3/4" (121mm) Vertical rod with 4 3/4" Mortise lock (121mm) device 260U (Top) 385A (Bottom) 260U (Stainless) 385A (Bottom) 304L (Bottom) 3 11/16" (94mm) 3 5/8" (92mm) Two vertical 3 11/16" rod devices (94mm) 3 5/8" (92mm) Vertical rod with 4 3/4" Mortise lock (121mm) device 4 3/4" (121mm) Single door 4 1/8" Two vertical 4 1/4" (108mm) (105mm) rods 304L (Bottom) Vertical rod with 4 3/4" Mortise lock (121mm) device 4 3/4" (121mm) 4 1/4" 4 1/4" (108mm) (108mm) 4 3/4" (121mm) 9847WDC-F 9947WDC-F 338 (Top) 385A (Bottom) Two vertical rod devices 4 1/4" (108mm) 4 1/4" 304L (108mm) 4 1/4" Two vertical 4 1/4" rod devices (108mm) (108mm) 9849 9949 9849 9949 249 (Top) 349 (Bottom) Vertical cable with Mortise lock device 4 3/4" (121mm) 4 3/4" (121mm) Vertical cable with 4 3/4" Mortise lock (121mm) device Two vertical cables 4 1/4" (108mm) 4 1/4" (108mm) Vertical cable with Mortise lock device 4 3/4" (121mm) 4 3/4" (121mm) Single door 4 1/4" (108mm) 4 1/4" (108mm) Two vertical cable devices 4 1/4" (108mm) 4 1/4" (108mm) — Two vertical 4 1/4" 4 1/4" Cable (108mm) (108mm) devices Vertical cable with Mortise lock device 4 1/4" (108mm) 4 1/4" (108mm) Vertical cable with 4 3/4" Mortise lock (121mm) device Two vertical cable devices 4 1/4" (108mm) 4 1/4" — (108mm) Two Vertical 4 1/4" 4 1/4" Cable (108mm) (108mm) Devices 9849-F 9949-F 9849-F 9949-F 9849WDC 9949WDC 9849WDC-F 9949WDC-F 54• Von Duprin 98/99 Series 54 249 (Top) 349 (Bottom) 249 (Top) 349 (Bottom) 249 (Top) 349 (Bottom) — 4 3/4" (121mm) 4 1/8" Two vertical 4 1/4" (108mm) (105mm) cable — Vertical cable with 4 3/4" Mortise lock (121mm) device Single door 4 3/4" (121mm) 4 1/4" 4 1/4" (108mm) (108mm) 4 3/4" (121mm) 98/99 Strike information Strikes for rim devices 264 299 299F 499F 1408 Projection 9/16" (14mm) Projection 13/16" (21mm) Projection 13/16" (21mm) Projection 15/16" (24mm) One per pair of doors 1439–Blade stop 1410–Integral stop 1606 1609 Projection 1/2" (13mm) Projection 1/2" (13mm) Projection 3/8" (10mm) Panic devices only – Requires coordinator – For panic exit application only, not fire rated Strikes for vertical cable devices 909 249 - Top249 strike 954 1" (25 mm) 349 349 - Bottom strike 1¹⁹⁄₃₂" (40 mm) 1¹⁄₂" (38 mm) 2³⁄₄" (70 mm) Projection 13/16" (21mm) ⁹⁄₁₆" (14 mm) Projection 7/8" (22mm) - For fire rated double door applications ¹⁄₈" (3 mm) Projection 9/16" (14mm) ¹⁄₈" (3 mm) Projection 1/8" (3mm) Strikes for vertical rod devices 248L-4 260U-Flush transom panic only 260U-F-Flush transom fire only 299 299F Projection 3/8" (10mm) Projection 3/8" (10mm) Projection 13/16" (21mm) Projection 13/16" (21mm) 304L 338 385A 283 Projection 13/16" (21mm) Mortise 5/8" (16mm) Mortise 2 1/2" (64mm) For use with WDC devices when used with wood frames 576A 576B Strike options / Dogging options XP Strikes for rim devices Strikes for mortise rod devices 575 575-2 . – Not for use with astragals – For use on wood doors, contact door manufacturer – Acceptable for 90 minute pair of hollow metal doors 55 Von Duprin 98/99 Series • 55 98/99 Dogging options CD Cylinder dogging SD Special center case dogging Cylinder dogging is available on all 98/99™ Panic exit devices to replace the standard hex key dogging. Unit requires a standard 1 1/4" (32mm) mortise cylinder with an inverted straight cam (Schlage Cam B502-191 reference). Special cylinder dogging in the center case is available for Chexit, EL, QEL, ALK panic devices to allow for mechanical push/pull operation. With this option, the latchbolt is held retracted and pushbar is still operable. Specify handing—RHR or LHR. To order, specify: • Use prefix, CD, example CD99L CDK Cylinder dogging kit* For field conversion, a cylinder dogging conversion kit is available. Note: Available on Rim and Vertical Rod Panic Exit Devices only. Order: 99CDK or 98CDK, specify finish. To Order, Specify: *Cannot be added to fire exit hardware. • Use prefix SD, example SD99L and Handing HDK Hex key dogging kit* For field conversion, a hex key dogging conversion kit is available. Strike options / Dogging options SD requires 1 3/4" (32mm) mortise cylinder with an inverted straight cam. (Schlage cam reference B502-191.) • Not for 98/9975 Devices Double cylinder Double cylinder features an inside key cylinder which locks or unlocks the outside trim and an outside key cylinder which retracts the latch bolt only (Night latch function). Available on rim or mortise lock device. Order: 99HDK or 98HDK, specify finish. *Cannot be added to fire exit hardware. LD Less dogging Less dogging is available in all 98/99™ Panic exit devices to remove the dogging option. To order, specify: • Use prefix LD, example LD99L Dog keys Dog key (old style) Dog key (standard) 2 3/16" (56mm) 2 3/4" (70mm) Rim requires two rim type cylinders. Mortise device requires 1 rim cylinder and 1 mortise cylinder 11/4" with a straight cam. (Schlage cam reference B502-191.) Available functions are thumbpiece, knob or lever. To order, specify: 1. Suffix-2 with device/trim number, example 99TP-2. /32" (6mm) hex 7 5 /32" (4mm) hex 2. Handing required, LHR or RHR. -2SI Double cylinder with security indicator The Von Duprin Classroom Security Indicator provides an at-aglance verification of the locked/unlocked status of the door from inside of the room. This option can be ordered as a new product or as a retrofit conversion kit to an existing 98/99 device. Indicator in Unlocked state presents a 1/2" x 1/2" metal flag (white background with black icon) at top of device head. Indicator in Locked state has no flag present. To order, specify: 1. S uffix-2SI with device/trim number, example 99L-2SI. 2. Handing required, LHR or RHR. 56• Von Duprin 98/99 Series 56 98/99 Electrical options RX Request to exit The RX (2xit) feature is used to signal the use of an opening. This device is equipped with one internal SPDT switch which monitors the pushpad. The device can be connected to a security console, or may be used as a single door alarm when used with a horn and power supply. The RX switch option should not be used to control a load, but as a signalling switch (0.5 amps. resisitive maximum). The RX switch is available in a low current (LC) switch. Most commonly used in computer operated monitoring systems. To order, specify: • • Standard – use prefix RX, example RX99EO Low Current – use prefix RX-LC, example RX-LC98EO RX2 Double request to exit The RX2 feature uses two RX switches. • Standard – Use prefix RX2, example RX299EO WP-RX Waterproof request to exit LX Latchbolt monitoring Monitors pushpad and latch bolt The SS feature is used to signal the unauthorized use of an opening. This device is equipped with two internal SPDT switches. One switch monitors both the pushpad and the latch bolt assembly, making the latch bolt tamper resistant, for positive security. An additional SPDT switch is connected to the 1 1/4" (32mm) mortise cylinder with straight cam for alarm “bypass.” (Schlage cam reference B502-191). The device can be connected to a security console, or may be used as a single door alarm when used with a horn and power supply. Pushpad reads: “Emergency Exit ONLY – Push To Open And Sound Alarm.” Pushpad is only available in US32D finish with red silk-screened lettering. The SS mortise lock device is furnished with both the signal switch device and the SS7500 mortise lock. The SS7500 mortise lock has the versatility and advantages of the 7500 lock with the addition of signalling functions to monitor latch bolt operation and the trim locking function. The SS7500 mortise lock is supplied standard with the SS mortise lock device. To order, specify: 1. Prefix SS, example SS99L. 2. Handing required, LHR or RHR. Electrical ratings: Up to 2.0 AMPS @ 24VDC The LX feature is used to signal the use of an opening. This device is equipped with one internal SPDT switch which monitors the latch bolt. The device can be connected to a security console, or may be used as a single door alarm when used with a horn and power supply. The LX switch option should not be used to control a load, but as a signalling switch (0.5 amps. resistive maximum). Popular SS application Unauthorized use of this opening will activate the local horn. The key switch permits inhibiting this system for authorized entry. Electrical options & accessories To order, specify: SS Signal switch The LX switch is available in a low current (LC) switch. Most commonly used in computer operated monitoring systems. To order, specify: • Standard – Use prefix LX, example LX99EO • Low Current – Use prefix LX-LC, example LX-LC98EO Electrical rating for all switches: • Standard – 2 Amp maximum @ 24VDC • Low Current (LC) - below 50 Milliamps @ 24VDC Note: All switches can be either factory or field installed 57 Von Duprin 98/99 Series • 57 98/99 Chexit device CX The Chexit® (with motor driven blocking actuator)* Minimum door opening sizes for CX devices Consult factory for other size requirements. Device 3' (914mm) Length 4' (1219mm) Length CX98/98-F/99/99-F 2'10 3/4" (883mm) 3'4 3/4" (1035mm) CX-XP98/XP98-F/XP99/XP99-F 2'10 3/4" (883mm) 3'4 3/4" (1035mm) Electrical options & accessories The Von Duprin Chexit device is designed for controlled egress applications. It meets both life safety and security needs, as well as the requirements of NFPA 101 for "Special Locking Arrangement" and IBC "Special Egress-Control Devices". All control inputs, auxiliary locking, local alarm and remote signaling outputs are self-contained in the Chexit assembly. Numerous configurable options allow the device to be customized for the specific code or application requirements. The standard Chexit device sounds an alarm and keeps the door secured for 15 seconds following an exit attempt with immediate release upon fire. CX9827/9827-F/9927/9927-F 2'10 1/4" (870mm) 3'4 1/4" (1022mm) CX9847/9847-F/9947/9947-F 2'10 1/4" (870mm) 3'4 1/4" (1022mm) CX9848/9848-F/9948/9948-F 2'10 1/4" (870mm) 3'4 1/4" (1022mm) CX9849/9849-F/9949/9949-F 2'10 1/4" (870mm) 3'4 1/4" (1022mm) CX9850/9850WDC-F/ 9950/9950WDC-F 2'10 1/4" (870mm) 3'4 1/4" (1022mm) CX9857/9857-F/9957/9957-F 2'10 1/4" (870mm) 3'4 1/4" (1022mm) CX9875/9875-F/9975/9975-F 2'10 1/4" (870mm) 3'4 1/4" (1022mm) Specifications / Power supply requirements* The Chexit device includes a 6" x 20" decal for application on door. Input voltage – 24VDC “PUSH UNTIL ALARM SOUNDS. DOOR CAN BE OPENED IN 15 SECONDS” Input current inrush – 1.25A Chexit typical applications Fire alarm, Inhibit and Door position switch inputs require normally closed dry contacts. Input current holding – 390mA Alarm relay and Secure relay contact ratings – 24VDC, 1A Chexit single door with options – The Chexit is used as an access control device. The card reader allows access. Also shown in this application is an external horn and door position switch. The auxiliary horn is used for increased volume in remote locations. Using a door position switch gives added security to the opening in case the door is not reclosed. With the Chexit disarmed, the opening functions as a normal exit device. If card readers are required on both sides of the door, the normally closed contacts of the readers should be wired in series. To fire alarm contact 2 x 18 AWG To secure status 2 x 18 AWG Gang group (optional) 1 x 18 AWG Remote Alarm 2 x 18 AWG Power supply Maximum number of devices PS902 (up to 2 amps) 1 Chexit device PS904 (up to 4 amps) 3 Chexit devices PS906 (up to 6 amps) 4 Chexit devices PS914 (up to 4 amps) 4 Chexit devices When powering multiple components, verify that the amperage requirements of all ** 2 x 14 902, 904, 906, or 914 Power supply Junction box 2 x 14 AWG 8 x 18 AWG Power supply information for CX devices with motor driven blocking actuator*. AC input components combined does not exceed the power supply output rating, see table above (See power supply instructions for output ratings. Consult Installation Instructions for proper wire gauge and wire run for AC input requirements) 2 x 18 AWG (plus power if required) 2 x 18 AWG requirements. Exceeding the recommended devices and/or not following Installation Instructions may void your warranty. Call Customer Care at 877-671-7011 or visit the Allegion website for more information - www.us.allegion.com. How to order* To order, specify: 1. Prefix product description number “CX”. Example: CX99L DPS 2. Specify option (see options on page 60). Example: CX-RCM or CD-CX EPT10 3. Door size other than 3' (914mm). 4. Door thickness other than 1 3/4" (45mm). Chexit 5. Finish. Card Reader **Note: PS902 is not to be used for double door Chexit applications. 1. Riser Diagram, Single Door FigureFigure 1. Riser Diagram, Single Door 58• Von Duprin 98/99 Series 58 6. H anding, LHR or RHR. Required with “CD” option. *Note: Chexit devices built after August 24, 2015 are built using motor driven blocking actuators that have decreased power supply and operating requirements. The information listed in this catalog references the power supply and operating requirements that are needed for the new products with motor driven blocking actuators. For information on devices built previous to August 24, 2015, please contact Customer Care at 877-671-7011. 98/99 Chexit, RCM and DE5300 features The Chexit, Remote Chexit Module (RCM) or DE5300 devices have several features and options available to fit your applications. See below for more information. Inputs & Outputs Fire Alarm Input This input releases the door immediately upon a fire alarm allowing immediate egress. The Internal Alarm can be silenced during a fire input via an onboard switch setting. Inhibit Input (Access Control) This optional input is provided to allow authorized egress or entry when the device is Armed using an external card reader, Key Switch, etc. It also allows remote reset of the Chexit, RCM or DE5300 in an alarmed condition. The ability to reset alarms with the inhibit input can be disabled via an onboard switch setting. Door Position Switch Input An optional Door Position Switch (DPS) can provide door position status to Chexit, RCM or DE5300 for additional security, ensuring that the door is closed, and can cause alarm when the door is left or forced open. Alarm Relay Contacts The Alarm Relay contacts are provided as a means to control a Remote Alarm, such as a horn or lamp, or signal an external monitor. The contacts can be configured with a jumper as Normally Open or Normally Closed, and become active upon entering an alarmed condition. Secure Relay Contacts The Secure Relay contacts are provided as a means to signal an external monitor. The contacts can be configured as Normally Open or Normally Closed with a jumper, and become active when the DPS indicates the door is closed and the Push Pad is locked. Delays Release Delay When the Push Pad is pushed and the Nuisance Delay expires, the Chexit, RCM or DE5300 enters the Release Delay with alarm. During the Release Delay, the Internal Alarm sounds, the Alarm Relay activates, and the Chexit/RCM keeps the Push Pad or DE5300 magnetic lock, locked for 15 seconds (less any time already elapsed during the Nuisance Delay). Once started, the Release Delay sequence will not stop and the devices will unlock. Nuisance Delay When a Chexit, RCM or DE5300 is located in a public area, it can be desirable to limit false releases when the Push Pad is accidently pushed. The Nuisance Delay is the brief time a Push Pad can be accidently pushed before the Release Delay sequence starts. If the Nuisance Time is set to 0 seconds the Chexit, RCM or DE5300 will enter Release Delay as soon as the Push Pad is pushed (when armed). Setting the Nuisance Time to 1, 2, or 3 seconds allows the Push Pad to be pressed for 1 to 3 seconds before the Chexit, RCM or DE5300 goes into Release Delay. If the Nuisance Audio and Nuisance Delay are both on, the Internal Alarm will pulse during the Nuisance Delay. The Alarm Relay does not activate during the Nuisance Delay. If the Push Pad is released before the Nuisance Delay expires, the Chexit, RCM or DE5300 will remain armed. DPS Delay If the DPS detects that the door closed during the Rearm Delay, the Chexit, RCM or DE5300 ends the Rearm Delay and allows 2 seconds for the latch to clear the strike before rearming. Interface Key Switch The Key Switch provides the means to Arm or Disarm/Reset the Chexit, RCM or DE5300. Turning the Key Switch clockwise initiates the Rearm Delay, and turning the Key Switch counterclockwise Disarms/Resets the Chexit, RCM or DE5300. The Key Switch allows the key to be removed in either the Arm or the Disarm/Reset position. Status Indicator The red Status Indicator displays the status of the Chexit, RCM or DE5300. The Status Indicator flashes slow if the Chexit, RCM or DE5300 is armed, flashes fast in an alarmed mode, is off when inhibited and on solid during Rearm Delay. Internal Alarm The Internal Alarm sounds the status of the Chexit, RCM or DE5300. The Internal Alarm sounds continuously during and after a fire alarm or a Release Delay, pulses fast during the Nuisance Delay or a tamper and pulses slow during Disarmed Powerup mode. Settings Armed Powerup When set to OFF, a power disruption and power return will put the Chexit, RCM or DE5300 in a disarmed, unlocked alarm mode. Trim Fail Safe / Fail Secure (FS/FSE) The trim input power can be set to FS (Fail Safe; locked when energized, unlocked when deenergized or during power failure) or FSE (Fail Secure; unlocked when energized, locked when deenergized or during power failure). Electrical options & accessories Gang Bus The Gang bus allows a Chexit, RCM or DE5300 device to signal other Chexit, RCM or DE5300 devices when it enters the Release Delay, allowing multiple doors to release at the same time in an emergency. Up to 8 devices may be connected to the Gang Bus. Rearm Delay The Rearm Delay is the amount of time after the Key Switch or Inhibit Input is deactivated to when the device rearms. It is designed to give someone time to pass through the door before rearming occurs. The Rearm Time can be changed via the onboard switch settings from 0 and 28 seconds in 2 second increments. If the Rearm Time is set to 30 seconds and a DPS is used, if the door is opened and the Rearm Time expires, there will be no alarm. The Chexit, RCM or DE5300 will rearm after the door is closed. If the door never opens, the Chexit, RCM or DE5300 will rearm after 30 seconds. If not using a DPS, the Chexit, RCM or DE5300 will always rearm in 30 seconds. The trim must be bought or modified to physically function as FS or FSE. This on board setting only selects the trim input power. 59 Von Duprin 98/99 Series • 59 98/99 Chexit options DE5300 Delayed Egress System RCM Remote Chexit Module — is designed to provide the concept of the Chexit delayed exit system for door sizes smaller than the standard Chexit device can accommodate. The Chexit module is installed in a control box and mounted in a remote location. Features and functions of the standard Chexit exit device are available on the Remote Chexit Module. DE5300 Delayed Egress System — is designed for controlled egress applications when used in conjunction with a magnetic lock. It meets both life safety and security needs, as well as the requirements of NFPA for "Special Locking Arrangement" and IBC "Special Egress-Control Devices". All control units, auxiliary locking, local alarm and remote signaling outputs are selfcontained in the DE5300 assembly. The DE5300 is commonly used on narrow stile doors where a standard or narrow stile Chexit is not practical. DE5300 Delayed Exit System uses a Chexit logic board and a Von Duprin RX-LC (low current request to exit) panic device to control a Schlage Electronics Direct Hold Magnetic Lock. RCM Module Minimum door opening sizes for RCM devices Electrical options & accessories Consult factory for other size requirements. Device 3' (914mm) Length 4' (1219mm) Length CX-RCM 98/98-F/99/99-F 2'5" (737mm) 2'11" (889mm) CX-RCM XP98/XP98-F/XP99/XP99-F 2'5" (737mm) 2'11" (889mm) CX-RCM 9827/9827-F/9927/9927-F 2'4 1/2" (724mm) 2'10 1/2" (876mm) CX-RCM 9847/9847-F/9947/9947-F 2'4 1/2" (724mm) 2'10 1/2" (876mm) CX-RCM 9848/9848-F/9948/9948-F 2'4 1/2" (724mm) 2'10 1/2" (876mm) CX-RCM 9849/9849-F/9949/9949-F 2'4 1/2" (724mm) 2'10 1/2" (876mm) CX-RCM 9850/9850WDC-F/ 9950/9950WDC-F 2'4 1/2" (724mm) 2'10 1/2" (876mm) CX-RCM 9857/9857-F/9957/9957-F 2'4 1/2" (724mm) 2'10 1/2" (876mm) CX-RCM 9875/9875-F/9975/9975-F 2'5 1/2" (743mm) 2'11 1/2" (902mm) Specifications / Power supply requirements* Size – 3.75" x 5.57" x 2.50" Input voltage – 24VDC Input current inrush – 1.25A Input current holding – 390mA DE5300 Module The Chexit module for the DE5300 is installed in a control box and mounted in the wall adjacent to the door. Features and functions of the standard Chexit exit device are available on the DE5300. The DE5300 device includes a 6" x 20" decal for application on door. “PUSH UNTIL ALARM SOUNDS. DOOR CAN BE OPENED IN 15 SECONDS” Cylinders — Cylinders are not furnished with the DE5300 and must be specified when ordering. Use 11/4” mortise cylinder with compression ring K510-406 with straight cam and orient cam as shown. Schlage cylinder 20-001-114 recommended for the device and the CD cylinder dogging option. See Schlage Pricebook for additional information. Specifications / Power supply requirements Alarm relay and Secure relay contact ratings – 24VDC, 1A Fire alarm, Inhibit and Door position switch inputs require normally closed dry contacts. Cylinder dogging — Special center case cylinder dogging option is available to allow push/pull operation of the Chexit, when disarmed and used in a heavy traffic area. Prefix device with “CD” and specify handing. Size - 3.75" x 5.57" x 2.50" Input voltage – 24VDC Input current – 1A Alarm relay and Secure relay contact ratings – 24VDC, 1A Fire alarm, Inhibit and Door position switch inputs require normally closed dry contacts. How to order To order, specify: 1. DE5300 2. M420/P, M450/P, or M490/P magnetic lock (order direct from Schlage Electronics). 3. RX-LC 22/33A/35A/98/99 device. Cylinders — Cylinders are not furnished with the Chexit device and must be specified when ordering. Use 11/4” mortise cylinder with compression ring K510-406 with straight cam and orient cam as shown. Schlage cylinder 20-001-114 recommended for 11/4” mortise cylinder with compression ring theUse device and the CD cylinder dogging option. See Schlage K510-406 with straight cam and orient cam as shown. Pricebook for additional information. Schlage cylinder 20-001-114 recommended. 1¹⁄₁₆" (27 mm) Maximum X Standard cam configuration (Shown with key removed) 4. PS900 Series 5. EPT-2/10 To fire alarm contact 2 x 18 AWG 2 x 18 AWG Remote Alarm Junction box Schlage 20-001-114 shown 2 x 18 AWG * CAUTION See Dimension X as shown above must be no more Chexit totoorder" onoccur. page than 11/16”"How or damage product may 5 x 18 AWG EPT2/10 58. *Note: RCM modules built after August 24, 2015 are built using motor driven DE5300 blocking actuators that have decreased power supply and operating requirements. The information listed in this catalog references the power supply and operating 1. See step 6l for conduit knockout requirements that are needed for the new products with motor driven blocking actuators. locations that can be used. For information on devices built previous to August 24, 2015, please contact 2. Trim wires not shown on diagram, Customer Care at 877-671-7011. RXLC Exit Device Card Reader add them as needed. 60 • Von Duprin 98/99 Series 60 AC input (See power supply instructions for AC input requirements) 2 x 18 AWG (plus power if required) Magnetic Lock 15 x 18 AWG How to order 902, 904, 906, 2 x 18 or 914 Power supply To secure status 2 x 18 AWG Figure 1. Riser Diagram, Single Figure 1. Riser Diagram, Single DoorDoor 98/99 Electrical options ALK Alarm kit Allegion Connect ALK Alarm kit is a simple yet effective way to deter unauthorized use of an opening. While the exit device is still a means of egress, the ALK kit contains an internal horn. When the touch bar is depressed, the horn sounds to provide an audible means of signaling that the opening has been violated. The alarm kit can be armed or disarmed by key thus allowing the exit device to be set in an armed or disarmed mode. The horn is rated at 85 decibels. For Hardware Applications The assembly includes both a 24VDC Input and External Inhibit standard. The External Inhibit provides remote arming and dis-arming. The alarm can automaticaly re-arm with a 1.5, 3 or 4.6 minute time delay upon request. Alarm kits are available with a choice of two switch kits, RX or LX. RX monitors the touchpad and is furnished standard. LX optional latch bolt monitoring is recommended for use with surface vertical rod exit devices or when alarm needs to sound from both the exit device and trim side of the door. Specify ALK-LX. Note: For latch bolt monitoring on a 98/9975 with ALK, specify a SS7500 lock. LX switch not available for 98/9975 devices. The ALK is available in two styles, 99ALK, grooved cover and 98ALK, smooth cover. The ALK includes a 6" x 20" decal for application on door “EMERGENCY EXIT ONLY. ALARM WILL SOUND. ”SS push bar trim can be used instead of the door decal, specify SS push bar trim when ordering the device. Features and benefits • Quick: common connections reducing installation time • Perfect Connections: these factory installed connectors ensure the right wires match up every time • Protective: the connectors protect the connection points throughout the installation process and lifetime of the opening • Interchangeable: all Allegion Connect products utilize the same connectors • Maintenance: you no longer need to cut away wire to disconnect Allegion products, also available is a service kit specifically for Connect products. Harness length 6 Inches 12 Inches 26 Inches 32 Inches 38 Inches 44 Inches 50 Inches 192 Inches Connectors on both ends CON-6 CON-12 CON-26 CON-32 CON-38 CON-44 CON-50 CON-192 Connectors on one end, crimped pins on the other end CON-6P CON-12P CON-26P CON-32P CON-38P CON-44P CON-50P CON-192P Power Supply Wire Harness = Connectors on one end, stripped leads on the other end, offering a direct connection to the power supply 6 Inches CON-6W - wire extension to power supply When the ALK is used, standard dogging is removed. If cylinder dogging is required there are two choices. Special center case dogging is available or for 3' or 4' doors. The ALK can be moved to the hinge side of the device and standard cylinder dogging can be added. Consult door manufacturer for harness length requirements. To Order, Specify: Note: Must be ordered with exit devices and locks 1. Standard, 98 ALK Electrical options & accessories The key switch uses a standard 1 1/4" (32mm) mortise cylinder with a straight cam (Schlage 20-001, B502-191 cam). The unit operates on one standard 9-volt alkaline battery. When the battery is weak, the horn will emit an intermittent low battery alert signal. Allegion’s cross-category Connect features common interconnect components to our electrified options. Allegion Connect is a quick and easy way to connect power sources; all the way from your power supply to locking device. There is no wire cutting; reducing installation and maintenance time ultimately cutting cost. After installation, Allegion’s Connect continues to provide benefits throughout the lifetime of the opening by offering a service kit for repairs or modifications in the future. Note: You will need to purchase a separate wiring harness to go from exit device to hinge/ EPT and an additional harness to go from hinge/EPT to power supply or access control system. Harness part numbers with ordering information can be located in the Schlage, Von Duprin and Falcon pricebooks. A service kit is available for order in the Schlage, Von Duprin and Falcon pricebooks. Included in this kit are male end plugs, female end plugs and pins to customize harnesses to your application. How to order 2. Cylinder Dogging, CD98 ALK 1. Specify CON for Connect electronic options Example: EL-99-EO-CON (99 Series Electrified Latching exit only with Connect connectors) 3. Special center case dogging, SD98 ALK 4. If AR desired, specify AR 1.5, 3 or 4.5 2. Specify harness length; Consult door manufacturer for harness length Minimum door opening sizes on ALK applications 3. Specify Von Duprin EPT10-CON or Ives 7200 power transfer hinge Device 3' (914mm) Length 4' (1219mm) Length Wire run options 98/98-F/99/99-F 2'10" (864mm) 3'4" (1016mm) 9875/9875-F/9975/9975-F 2'10" (864mm) 3'4" (1016mm) 9827/9827-F/9927/9927-F 2'10" (864mm) 3'4" (1016mm) 9857/9857-F/9957/9957-F 2'10" (864mm) 3'4" (1016mm) 9847/9847-F/9947/9947-F 2'9" (838mm) 3'3" (991mm) 9848/9848-F/9948/9948-F 2'9" (838mm) 3'3" (991mm) 61 Von Duprin 98/99 Series • 61 98/99 Electrical options EL Electric latch retraction QEL Quiet electric latch retraction If manual hex-key dogging is required, specify HD-EL. If cylinder dogging is required, the standard cylinder dogging is not available, but special center case dogging is available, specify SD-EL. SD-EL is not available on the 9875 or 9975 devices. If cylinder dogging is required, the standard cylinder dogging is not available, but special center case dogging is available, specify The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging. EL devices are also useful with automatic door operators, and may be applied to fire-rated applications when under the control of an automatic fire alarm system. UL approved for Class II circuit applications. Electrical options & accessories The EL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS914 power supply. The PS914 with the 9002RS option card is the minimum option card required. Other option cards available for other functions, see PS914 power supply for additional information. Solenoid specifications: Continuous duty – 24 VDC Current inrush – 16 Amps Current holding – 0.3 Amps Solenoid resistance: -grn-yel 1.2 – 2.2 OHMS -grn-org 100 – 150 OHMS PS872 Wiring To order, specify: Standard – use prefix EL, example EL99L. Hex Key dogging – Use prefix HD-EL, example HD-EL99L special center case dogging – Use prefix SD-EL, example SD-EL99L Popular EL application Power supply PS914-2RS Electric power transfer EPT-2 or EPT-10 The QEL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. Different than the popular EL, the QEL quiet operation is achieved using an electric drive motor which retracts the latch bolt either momentary unlatching or for extended periods of time. This feature is an alternative to manual dogging. SD-QEL. SD-QEL is not available on the 9875 or 9975 devices. QEL devices are also useful with automatic door operators, and may be applied to fire-rated applications when under the control of an automatic fire alarm system. UL approved for Class II circuit applications. The QEL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS902 or 914 power supply. The PS902/914 with the 2RS, 4RL or 4R board is the minimum required. Other option boards available for other functions, see PS902/914 power supply for additional information. The QEL has a low in rush current, so it can be used with standard Schlage power supplies. Calculate the peak current draw of all devices in the system to determine the required amperage of the supply. Schlage PS902 Schlage PS904 Schlage PS906 up to 2 amps up to 4 amps up to 6 amps QEL Electrical load Voltage 24VDC Current 1.0 A Inrush (0.5 sec.) / 0.14 A Holding The -2RS option board is designed to control two electric latch retraction devices and provide time delay between the firing of outputs is required. The power transfer is also sold separately. PS872 Wiring 120/240 VAC SC I1 O1 I2 O2 GND To order, specify: Standard — use prefix QEL, example QEL99L. Special center case dogging — use prefix SD-QEL, example SD-QEL99L EPT-2 EL #2 a* Popular application Power supply PS902-2RS Electric power transfer EPT-2 or EPT-10 Input #2 (Required for independent operation only). b* 120/240 VAC EPT-2 SC I1 O1 I2 O2 GND EPT-2 EL #1 a* Von Duprin exit device * b* Input #1 All other 98/99EL device types Control Switch EL Wire length (feet)1 Wire gauge (AWG) 0-500 12 0-300 14 0-200 0-250 16 12 0-150 0-100 0-1200 (Required for independent operation only). EPT-2 QEL #1 a* Input #1 b* a* Distance (one-way) 200´ Wire gauge 18 AWG 14 320´ 16 AWG 16 500´ 14 AWG 18 800´ 12 AWG 1. Wire lengths include an EPT, Door loop, electric hinge or pivot and are measured one way between the PS914/option board and the device. 2. Table is applicable to devices that have shipped after August 2012. 62• Von Duprin 98/99 Series 62 Input #2 b* b* EL 98/99 Rim a QEL #2 a* b* Wire selection 1200 ft. Max. Switch wire size 18 gauge standard 98/99 Electrical options Power Supplies Series PS902/914 PS902 PS904 PS906 PS914 Number of connectors on power supply for the following: 2 amps 4 amps 6 amps 4 amps Distribution boards 1 2 3 2 Battery back-up board 1 1 1 1 Note: One fire alarm board can be connected directly to the PS902. If a fire alarm board is desired for the PS904, PS906 or PS914 it can be connected to a distribution board. Overview: Note: PS906 can provide Class 2 rated outputs when used with 900-8P distribution board. Features: • Constant output rating at both 12 VDC and 24 VDC provides superior performance ; includes field selectable jumper • Polarized connectors for option boards eliminate need for racks and side connectors • Flat mounting of option boards provides easier access to terminal blocks for connection of electrified devices • High voltage protective cover • Battery back-up board auto-selects voltage • Fire alarm relay can be configured to provide either switched or un-switched outputs from a power supply • PS914 designed with high in rush current for powering electrified panic devices Applications: The PS900 Series of power supplies works with many electrified devices including Schlage electromagnetic locks, Schlage AD-Series hardwired locks, Schlage electrified mechanical locks, Von Duprin electrified strikes , Von Duprin exit devices, and many other brands. Accessories: The Schlage PS900 Series features seven option boards for use in a variety of applications. All Schlage PS900 Series power supplies option boards are UL 294 certified. Option boards: 900-4R: 4 relay controlled output board to power multiple devices 900-4RL: 4 relay distribution board with logic is field configurable for time delay function, auto operator, security interlock 900-8F: Provides 8 individually fuse-protected outputs, giving the flexibility to power multiple devices and provide another layer of protection 900-FA: Emergency interface relay integrates with fire alarm and is used to cut power in case of emergency 900-BB: Battery backup • Universal 120-240 VAC input 900-2RS: 2 relay EL panic device control board (PS914 only) • Low voltage DC, regulated and filtered 900-BBK: Battery backup kit includes two 7A/hr batteries and provides up to four hours of backup power when cycled every 5 minutes at full load • Electronic power limiting foldback circuit for AC current overload protection Electrical options & accessories The PS900 Series is a consolidated line of power supplies and accessories that offer enhanced flexibility and functionality specific to the changing needs of the access control market. The PS900 Series can be used in a variety of applications to convert high voltage AC power into the low voltage DC outputs required by most access control devices. The PS900 Series protects devices downstream by providing Class 2*, filtered and regulated power. The full line is UL294 certified. • Fused primary input • AC status monitor- isolated SPDT contacts • AC input and DC output LED status indicators • Cover mounted AC input indication • Hinged cover with lock down screws Certifications: • UL 294 certified—the standard for access control • Class 2 rated* * Except PS906, output rating exceeds Class 2 power limits Once power is converted to low voltage DC, the PS900 Series offers a variety of distribution options, including basic fuse protection, simple relay, and advanced logic providing complex sequencing and timing functions. * PS906 can provide Class 2 rated outputs when used with 900-8P distribution board. 63 Von Duprin 98/99 Series • 63 98/99 Electrical options EPT Electrical power transfer PNT Pneumatic transfer E Electric mortise lock device Two models are available; EPT-2, two 18 gauge wires and EPT-10, ten 24 gauge wires. The EPT-2 and EPT-10 are U/L listed as “miscellaneous door accessory”. The electric mortise lock device has all the versatility and advantages of the standard mortise lock device, plus the advantage of being electrically controlled by a remote switching device, an access control system or an automatic fire alarm system. The device features the E7500 mortise lock. The E7500 controls the locking of the outside trim. When unlocked, the door remains latched, preserving the fire rating of the door and making it particularly useful where codes permit locking but require unlocking during a fire emergency. The outside trim cylinder retracts the latch bolt for mechanical override, night latch function. Only available with TP, K or L functions. Electric Power Transfer provides a means of transferring electrical power from a door frame to the edge of a swinging door. The units are completely concealed when the door is in the closed position, and are ideal for installations involving abuse or heavy traffic. UL Listed for use on firedoors Door applications: up to 5" butt hinges – 180˚ swing, 5 1/2" butt hinges – 130˚ swing, 6" butt hinges – 110˚ swing, /4" butt offset pivots 180˚ swing. Electrical options & accessories 3 Finishes The E7500 lock contains a SPDT signal to monitor the outside trim condition (locked or unlocked) and a second SPDT signal switch to monitor the latch bolt. SP28 (sprayed aluminum) Standard features: SP313 (sprayed duranodic). • Field reversible handing Dimensions • 24 VDC continuous duty solenoid Not for use with swing clear hinges or center-hung pivots. Housing 9" x 1¹|₄" x 1⁵|₈" (229mm x 32mm x 38mm) Optional features: EPT-2 Two 18 gauge wires, Up to 2 AMPS @ 24VDC, with a 16 AMPS Maximum Surge • Fail safe (locked when energized, unlocked when deenergized or during power failure). Specify with suffix “FS.” EPT-10 Ten 24 gauge wires, Up to 1 AMPS @ 24VDC, with a 16 AMPS Maximum Surge • Fail secure (unlocked when energized, locked when deenergized or during power failure). Specify with suffix “FSE” PNT-1 ⁵|₃₂" Tubing • 24 VAC (with SO option) To order, specify: 1. EPT-2 ,EPT-10 or PNT-1. • 12 VDC • 12 VAC (with SO option) 2. Finish, SP28 or SP313. Note: Some Fire codes will require “Fail Safe” (FS) operation for stairwell doors.Be sure to specify the correct operation for your application. E996L Electrified breakaway lever Electrical specifications: E996L Electrified lever trim provides remote locking and unlocking. Furnished standard in fail safe (FS) condition, can be field converted to fail secure (FSE) where allowed. E996L is furnished standard with cylinder operation for nightlatch (NL) function, or with blank escutcheon (BE). Specification: Solenoid – continuous duty 24VDC Solenoid draw – 0.22 amp. To order, specify: 1. Use “E” prefix, example E996L. When ordering with the exit device specify trim series with prefix “E”, example 9927L-BE 3' US26D E996. 2. Device type, R/V (rim/surface vertical rod/concealed vertical rod) or M (mortise). 3. RHR furnished standard if not specified, field reversible. 4. L ever style (06 lever furnished standard). Other levers, no extra charge. 64 • Von Duprin 98/99 Series 64 • Solenoid — .60 AMPS @ 12VDC .30 AMPS @ 24VDC • Each switch — Up to 2.0 AMPS @ 24VDC Maximum The E option does not include the power transfer from door to frame, the power supply or the control operator. (Refer to EPT-10 and PS902 or PS914 power supply) To order, specify: 1. Use prefix “E,” example E9975. 2. FS or FSE 3. Voltage and current. Electric mortise lock device Adaptable for openings where continuous latching is required while the trim may be electrically locked or unlocked from a remote location—stairwells, exterior doors, etc. Minimum system requirements: • PS902 • EPT-10 98/99 Mechanical options AX Accessible device The AX device is a UL certified exit device designed to meet the progressive requirements of the California Building Code for accessible openings. This device meets the 5 lbs of operating force requirement called for in chapter 11B-309.4. The AX device also exceeds ANSI/BHMA requirements. Available devices include: AX98/99, AX98/99-F, AX98/9949LBL, AX98/9949-F LBL, AX98/9949-F LBLAFL. Additionally, all AX devices will be shipped with a new UL label clearly stating “Meets California building Code (2013) Sec. 11B-309.4” and an “AX” identifier label on device center case. See images below for reference. WS Surface vertical rod one-point and three-point exit devices WS Multi-point exit devices for tornado application devices WS98/9927 (one- point) and WS98/9957 (three-point) surface vertical rod exit devices are designed, tested and certified to comply with the Federal Emergency Management Agency's publication FEMA 361- Design and Construction Guidance for Community Safe Rooms. UL Listing – panic hardware UL 305; and fire exit hardware UL 10C: WS98/9927: 3 hour pairs of doors double egress, 90 minutes swinging same direction, 8'0" x 8'0" BHMA Grade 1, ANSI A156.3-2001 WS98/9957: 3 hours single doors, 4'0" x 8'0" BHMA Grade 1, ANSI A156.3-2001 XP Extra performance For increased security the XP98/99 Rim exit device has a static load force resistance of more than 2,000 pounds, twice that of standard rim exit devices. The two-piece latch bolt forms a 90° latch-tostrike contact. The “smart” latch changes shape when subjected to external forces. This design enables the exit door to withstand an external attack and remain secure. Additionally, the patented latch bolt design provides a greater, longer-lasting latch bolt to strike contact which is not easily affected by the twisting motion of a weakened frame, resulting in an opening that will remain strong. With a door loaded to 250 pounds, XP98/99 requires less than 40 pounds of pressure to open, 25% less than the safety code requires. XP98/99 is available for panic or fire exit hardware applications. Dimensions, finishes and trim options are equal to the standard 98/99 series rim exit device. Note: The 909 strike is to be used for all applications. The exception occurs with the use of fire rated double door applications, in this instance the 954 strike is required. UL-FEMA 361 certified 8'0" x 8'0" pairs, swinging same direction and 4'0" x 8'0" single non-fire rated flush hollow metal. UL-ANSI/ICC 500 certified for F5 tornado applications. WS98/9957: UL-FEMA 361 certified 4'0" x 8'0" single flush hollow metal (fire-rated and panic). UL-ANSI/ICC 500 certified for F5 tornado applications. These devices are listed with Steelcraft Paladin™ PW-Series doors for tornados, and Steelcraft H-Series doors hurricane applications. To order, specify: WS prefix, example WS9927-F LBR Less bottom rod, panic and fire rated LBR option is available, using a spring loaded auxiliary latch bolt installed in the lower door edge. When exposed to heat the auxiliary latch bolt releases, keeping the doors in alignment and closed during a fire. UL listed 3 hours on hollow metal doors double egress, 90 minute swinging same direction, and 20 minutes wood doors (consult wood door manufacturer). Fits door stiles as narrow as 3 5/8". Mechanical options & accessories Windstorm ratings: WS98/9927: Miami-Dade County/FBC compliance to TAS 201, TAS 202, TAS 203; design load rating +150/-150 PSF (245 MPH wind zone); Enhanced Hurricane Protection (EHPA) ASTM E1996, ANSI/ICC 500 (245 MPH wind zone). LBR devices must be ordered in pairs or must be used in conjunction with an approved automatic or constant latching flush bolt. PL Pullman latch When PL is specified the standard latches are replaced with pullman style latches. Pullman latches are always extended and are most commonly used in conjunction with electric strikes and LBR-less bottom rod application. Not available with Fire rated devices. Not recommended where security is of the utmost importance since latches do not deadlock. 65 Von Duprin 98/99 Series • 65 98/99 Mechanical options PN Pneumatic controlled exit devices Mechanical options & accessories The PN feature provides remote latch bolt retraction in hazardous areas where electrically operated devices would not be permitted. The pneumatic solenoid will retract the latch bolt for momentary or prolonged periods. PN exit devices are particularly suited for use with automatic door operators. The PN feature is available on both Panic and fire exit hardware devices. The PN feature includes a special actuating linkage that gives building owners the option of mechanically or pneumatically dogging the exit device. If manual hex-key dogging is required, specify HD-PN (Dogging the device, whether mechanically or pneumatically, makes the device function as a push/pull unit and reduces the wear on its moving parts.) If cylinder dogging is required, the standard cylinder dogging is not available, but special center case dogging is available, specify SD-PN. SD-PN is not available on the 9875 or 9975 devices. When activated pneumatically, the latch bolt(s) of the exit device retract in 1/2₂ to 11/2 seconds. This pneumatic operation uses air pressure ranging from 50 to 100 pounds per square inch. This product will function only when it is part of a pneumatic system (air compressor, air lines, pneumatic system, etc.). Contact LCN for correct control boxes. To order, specify: • Standard — Use prefix PN, example PN99NL • Hex Key Dogging — Use prefix HD-PN, example HD-PN99NL • Special Center Case Dogging (handing is required, specify RHR or LHR) — Use prefix SD-PN, example SD-PN99NL Dummy pushpad The 330 dummy pushpad is designed as a companion unit for all 99 devices. The 350 dummy pushpad is a companion unit for all 98 devices. The pushpad is rigid or nonfunctioning. A push/pull operation can be accomplished by using 990DT, 996DT trim or any Ives Pull. The 330/350 can be equipped with a functional pushpad and will accommodate an RX or WP-RX switch. Specify RX-330. May also be equipped with the RX2, double RX switch. Specify RX2-330 To order, specify: 1. 330 or 350. 2. Size 3' or 4' (914mm or 1219mm) 3. Finish, US3, US4, US10, US26, US26D, US28, 313 & 315. US32D – 350 only. 4. Specifiy RX, WP-RX or RX-2 if desired. SG Safety glow Self-illuminating touchpad defines the location of the exit door in dark or smoke-filled area. The safety glow coating is a special powder coat finish that glows brightly during low or no light conditions. This coating was developed to meet MEA standards where luminescent exit door markings are required in commercial facilities. There are no batteries or electronics, the coating is charged when exposed to light. To order, specify: Suffix SG, EL 9927L-SG Braille, embossed and knurled touchpads PNT pneumatic transfer Pneumatic controls PNT-1 is available for pneumatic latch retraction exit devices. Appearance and dimensions are identical to EPT models. * Image shown is a special order. RSS Red Silk Screen Braille touchpad embossed with the standard message “CAUTION S TAIRWELL” in braille and raised letters provides assistance to persons with impaired vision. Letters are 1/2" (13mm) high and braille is #2, raised height is 3/32" (2mm). Other messages are available on special order, limited to 20 characters per line.* To order, specify: Suffix BR, EL9927L-BR Red silkscreen lettering on touchpad trim. - "Emergency Exit Only, Push To Open And Sound Alarm". This comes standard on SS devices. To order, specify: Suffix RSS, 9927L-RSS RHR 66 • Von Duprin 98/99 Series 66 Embossed touchpad is embossed with the word “PUSH”. To order, specify: Suffix EMB, EL9927L-EMB Knurled touchpad is to provide warning to persons with impaired vision. To order, specify: Suffix PBKN, EL9927L-PBKN Consult factory for availability. 98/99 Device options & accessories RG-27 Vertical rod and latch guard Series RG-27 Vertical rod and latch guards protect the bottom rods of exit devices from the damaging impacts of carts or gurneys passing through doors. (If bottom rods become damaged, the exit device will not function as intended and can jeopardize the ability to exit safely during an emergency.) 36" In addition to protecting the vertical rod, the guard provides a smooth, unobstructed surface so the door can be pushed open easily with the bumpers of a wheelchair. The latch guard portion is 10" high. The standard latch guard features a 45° ramp. The extended latch guard offers a continuous ramp in 3' or 4' widths. All stainless steel construction in US32D finish. Latch guards can cover latches as large as 1 1/4"W x 10"H x 1 7/8" projection. 997 Cover plate kit For 98/99 rim device, kit contains inside and outside plates for hinge stile cutouts, an inside plate for the lock stile, and necessary screws. Plates are designed to cover cutouts required by most existing exit device installations. Specify finish. 13/4" (44mm) 9" (229mm) WDA Cover plate kit For wood door applications, used to cover up door preparations for control, also prevents the control from boring into the wood door. Finished to match control. #10WDA Cover plate kit for 370 series controls Extended latch guard Latch guard 7 7/8" 7 7/8" 10" 12" 3' or 4' 4 3/8" #33A-WDA Cover plate kit for 360 series controls 2 1/4" 2 1/16" 2 1/16" Models RGO Rod guard only (projection 1 3/16") RG-27 Rod and latch guard RG-27-3 3' (914mm) Rod guard and extended latch guard RG-27-4 4' (1219mm) Rod guard and extended latch guard LGO Latch guard only LGO-3 3' (914mm) Extended latch guard only LGO-4 4' (1219mm) Extended latch guard only When using on wood fire doors, high density block is required. To order, specify: 1. Model number. 2. Handing (except on RGO). GBK Glass bead kit Glass bead conversion kits are available for all 98/99™ Series devices for use on doors with raised glass beads. Each kit consists of 1/4" (6mm) shim sets. GBK for surface vertical rod ships with 1/8" shims for rod guides. Device options & accessories Rod guard To order, specify: 1. 99GBK 2. Device type (rim, mortise, surface vertical rod, concealed vertical rod) 3. Wood door, when used with concealed vertical Rod 4. W hen used with 330/350 Dummy pusher, order two hinge stile shims. 3. Door material if other than hollow metal. 4. Optional sex bolt mounting available. 67 Von Duprin 98/99 Series • 67 98/99 Device options & accessories Cylinders Cylinders are not furnished with device or trim and must be specified when ordering. Refer to trim pages for cylinder type. Device options & accessories Mortise — 3215 (Schlage 20-001, B502-191 cam) Dogged (inverted) cam Undogged cam (standard operations) For cylinder dogging or 360L For standard trim functions or 360L-NL 68 • Von Duprin 98/99 Series 68 Rim — 3216 (Schlage 20-022 cam) 98/99 Device options & accessories Mullions Removable steel mullions provide single door performance in double door openings with rim devices. Mullions are easily removed by loosening bottom set screw and removing top fitting cover. The top mullion fitting is attached to the frame and is concealed by the fitting cover. Steel mullions are 2" (51mm) wide and 3" (76mm) deep, with a wall thickness of 1/8" (3mm). Mullions are shipped with mounting screws and prepared for strikes. Strikes are not included except where indicated. Steel mullions are available in SP28 and SP313 finishes. Consult factory for other powder coat finish options. KR – Keyed removable steel mullions make removal faster and easier by a single operation of the mortise cylinder. Once mullion is removed, large equipment or furniture can freely pass through the opening. The unit will self lock when reinstalled, without the use of the cylinder key. Uses a 1 1/4" mortise cylinder with a straight cam (Schlage cam reference B502-191). Cylinders are sold separately. Prefix mullion model with “KR”. Aluminum mullions are available in US4, US10, US28, 313 and 315 finishes. Consult factory for other powder coat finish options. Aluminum mullion are not available keyed removable. Stock hollow metal applications for devices mounted to cover ANSI 161 cutouts are higher than the standard mullion strike location. Consult the factory for special strike preparation or order a blank mullion. See below. Blank mullions are furnished without strike preparation. They are used to mount devices at a strike height different from the standard mullion preparation. To order, specify: 1. For keyed Removable option on steel mullions, prefix model number with “KR” 2. Model number 3. Height of opening 4. Finish 5. Handing if required 6. Centerline deviation (refer to device template for standard centerline) 7. Strikes, when required, should be ordered with device Keyed removable steel mullions Steel mullions 1654 Prepared for two 1606 strikes. If 1606 strikes are not specified on the order, two per mullion will be added. Additional charges apply. 4954 Prepared for 264 or 299 strikes. For use with all Von Duprin Panic rim devices. 9954 Prepared for and must be used with two 268 strikes (88-F device), or two 499F (22-F, 98-F, 99F devices). UL fire labeled mullion for up to 3 hour opening using Von Duprin fire exit rim devices. This mullion is not easily removed due to special fittings. 98-F and 99-F devices are rated up to 10'0" (3048 mm). Note: If 268 or 499F strikes are not specified on the order, two per mullion will be added. Additional charges apply. 4754 Prepared for two 4263 monitor strikes. 4854 Prepared for one 299 and one 6111 electric strike. Indicate handing for electric strike. Device options & accessories Removable aluminum mullions are 1 1/16" (27mm) wide on face closest to the door and 23/8" (60mm) at the widest point. The depth is 3 1/8" (79mm) with a wall thickness of 1/8" (3mm). Removable mullions 9854 Prepared for one 268 or 499F strike and one 6111 electric strike. Indicate handing for electric strike. UL fire labelled mullion for up to 3 hour openings up to 8' x 8' (2438mm x 2438mm) using Von Duprin fire exit rim devices 69 Von Duprin 98/99 Series • 69 98/99 Device options & accessories Sex bolts 325 sex bolts used on surface Vertical Latches. Sex bolts when ordered with devices may be furnished with screw lengths different than shown in Column B. Below, Column B indicates popular sizes. Sex Bolts ordered separately are not furnished with screws. If screws are required refer to chart below and order screws by description as a separate item. Other screw lengths may be used based on minimum and maximum allowable thread engagement, shown in column “C.” Quantity required — refer to device section, quantities differ depending on outside trim. 425 sex bolts are required for 98/99 Series fire rated devices when used on wood door applications. When wood doors are specified for these devices, sex bolts will be added to the device application unless SLM blocking package is specified. 825 sex bolts are required with 98-F/99-F rim devices on wood door applications using NL, TP, K and L outside trims. Two 825 sex bolts will be added to the device application unless SLM blocking package is specified. To order, specify: 1. Model number 325 425 2. Quantity (2 per package) 3. Finish Device options & accessories 4. Door thickness other than 1 3/4" (44mm) 825 Rim, mortise and concealed vertical Center case Device type Door thickness Sex bolt Hinge case B /32" – 1 /16" 425 1 /16" 10-24 x 1" PPHMS 9 /32" – 1 9/16" 425 1 9/16" 10-24 x 11/2" PPHMS 9 /32" – 1 9/16" 425 1 9/16" 10-24 x 3/4" PPHMS ⁹9/32" – 1 9/16" /32" – 1 9/16" 425 1 9/16" 10-24 x 11/4" PPHMS 9 425 1 /16" 10-24 x 1" PPHMS 9 425 1 9/16" 10-24 x 1 1/2" PPHMS 9 1 3/4" (44mm) 425 825A* 1 9/16" 1 13/16" 10-24 x 1" PPHMS 10-24 x 3/4" PPHMS 2 1/4" (57mm) 425 825B* 1 9/16" 25/16" 10-24 x 1 1/2" PPHMS 10-24 x 3/4" PPHMS 9 Surface vertical rod - latches only Latch case Door thickness Sex bolt B no. A Screw 1 /4" (44mm) 325 1 9/16" 1 2 1/4" (57mm) 325 1 9/16" 1 3 PPHMS – Pan phillips head machine screw UFPHMS – Undercut flat phillips head machine screw * For use with outside trims. 70• Von Duprin 98/99 Series 70 Screw Screw * For use with outside trims, see page XX for details 9827/9927/9827F, 9927F A A 98-F, 99-F* Device type no. no. 98, 9827, 9827-F, 1 3/4" (44mm) 9875, 9875-F, 9847, 9847-F, 9847WDC, 9849, 9849-F 99, 9927, 9927-F, 9975, 9975-F, 2 1/4" (57mm) 9947, 9947-F, 9949, 9949F, 98/9949WDC, 98/9949WDC-F /4 - 20 x 3/4" FPHMS /4 - 20 x 1/4" FPHMS C Thread engagement min. – max C Thread engagement min. – max 9 9 9 Sex bolt B 9 /32" – 1 9/16" /32" – 1 9/16" /32" – 1 9/16" 98/99 Function, grade, type options ANSI Function, grade & type Function Grade 1, type 1 Grade 1, type 2 Grade 1, type 3 Grade 1, type 7 Grade 1, type 7 Grade 1, type 8 Grade 1, type 8 Grade 1, type 8 Grade 1, type 9 1 98EO & F 99EO & F 9827EO & F 9927EO & F 9875EO & F 9975EO & F 9847WDCEO & F 9947WDCEO & F 9849WDCEO & F 9949WDCEO & F 9847EO & F 9947EO & F 9848EO & F 9948EO & F 9849EO & F 9949EO & F 9857EO & F 9957EO & F 2 98DT 99DT 9827DT 9927DT 9875DT 9975DT 9847WDCDT 9947WDCDT 9849WDCDT 9949WDCDT 9847DT 9947DT 9848DT 9948DT 9849DT 9949DT 9857DT 9957DT 3 98NL & F 99NL & F 9827NL & F 9927NL & F 9875NL & F 9975NL & F 9847WDCNL & F 9947WDCNL & F 9849WDCNL & F 9949WDCNL & F 9847NL & F 9947NL & F 9848NL & F 9948NL & F 9849NL & F 9949NL & F 9857NL & F 9957NL & F 3 98K-NL & F 9827K-NL & F 9875K-NL & F 9847WDCK-NL & F 9849WDCK-NL & F 9847K-NL & F 99K-NL & F 9927K-NL & F 9975K-NL & F 9947WDCK-NL & F 9949WDCK-NL & F 9947K-NL & F 9848K-NL & F 9849K-NL & F 9857K-NL & F 9948K-NL & F 9949K-NL & F 9957K-NL & F 3 98L-NL & F 9827L-NL & F 99L-NL & F 9927L-NL & F 9875L-NL & F 9847WDCL-NL & F 9849WDCL-NL & F 9847L-NL & F 9975L-NL & F 9947WDCL-NL & F 9949WDCL-NL & F 9947L-NL & F 9848L-NL & F 9849L-NL & F 9857L-NL & F 9948L-NL & F 9949L-NL & F 9957L-NL & F 5 98TP & F 99TP & F 9875TP & F 9975TP & F 7 98TP-2 & F 99TP-2 & F 8 98K & F 99K & F 9827K & F 9927K & F 8 98L & F 99L & F 9827L & F 9927L & F 10 98K-2 & F 99K-2 & F 9875K-2 & F 9975K-2 & F 10 98L-2 & F 99L-2 & F 9875L-2 & F 9975L-2 & F 9847WDCTP & F 9947WDCTP & F 9849WDCTP & F 9949WDCTP & F 9847TP & F 9947TP & F 9848TP & F 9948TP & F 9849TP & F 9949TP & F 9857TP & F 9957TP & F 9875K & F 9975K & F 9847WDCK & F 9947WDCK & F 9849WDCK & F 9949WDCK & F 9847K & F 9947K & F 9848K & F 9948K & F 9849K & F 9949K & F 9857K & F 9957K & F 9875L & F 9975L & F 9847WDCL & F 9947WDCL & F 9849WDCL & F 9949WDCL & F 9847L & F 9947L & F 9848L & F 9948L & F 9849L & F 9949L & F 9857L & F 9957L & F 9847WDC & F 9947WDC & F 9849WDC & F 9949WDC & F 9847TL & F 9947TL & F 9848 & F 9948& F 9849 & F 9949& F 9857TL & F 9957TL & F 9875TP-2 & F 9975TP-2 & F 9827TL & F 9927TL & F 14 98K-BE & F 9827K-BE & F 99K-BE & F 9927K-BE & F 9875K-BE & F 9847WDCK-BE & F 9849WDCK-BE & F 9847K-BE & F 9975K-BE & F 9947WDCK-BE & F 9949WDCK-BE & F 9947K-BE & F 9848K-BE & F 9849K-BE & F 9857K-BE & F 9948K-BE & F 9949K-BE & F 9957K-BE & F 14 98L-BE & F 9827L-BE & F 99L-BE & F 9927L-BE & F 9875L-BE & F 9847WDCL-BE & F 9849WDCL-BE & F 9847L-BE & F 9975L-BE & F 9947WDCL-BE & F 9949WDCL-BE & F 9947L-BE & F 9848L-BE &F 9849L-BE &F 9857L-BE & F 9948L-BE & F 9949L-BE & F 9957L-BE & F 16 9827TL-BE & F 9927TL-BE & F 9847WDC & F 9947WDC & F 9849WDC & F 9949WDC & F 9847TL-BE & F 9848 & F 9947TL-BE & F 9948 & F 9849 & F 9949 & F 9857TL-BE & F 9957TL-BE & F Additional information 11 12 9827TP & F 9927TP & F Dimensions 71 Von Duprin 98/99 Series • 71 UL Listing for fire exit hardware UL Listed fire exit hardware label and opening size Double door Door material With 9954 Single door mullion With 9854 mullion With kr9954 mullion With kr9854 mullion Vxv V x mortise Vxv same direction same direction double egress 98-F 99-F Metal 3 Hour 4' x 10' 3 Hour 8' x 10' 3 Hour 8' x 10' 3 Hour 8' x 8' 3 Hour 8' x 8' — — — 9875-F 9975-F Metal 3 Hour 4' x 10' — — — — — 3 Hour 8' x 10' — 3 Hour 8' x 10' 3 Hour 8' x 10' Additional information Exit device 9827-F 9927-F Metal — — — — — 90 Minute 8' x 10' 9827LBR-F 9927LBR-F Metal — — — — — 90 Minute* 8' x 10' — 3 Hour 8' x 10' 9857-F 9957-F Metal 3 Hour 4' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' — — — 3 Hour 8' x 10' 3 Hour 8' x 10' * 9847-F 9947-F Metal — — — — — 90 Minute 8' x 10' 9847LBR-F 9947LBR-F Metal — — — — — 90 Minute* 8' x 10' — 3 Hour 8' x 10' 9848-F 9948-F Metal — — — — — 90 Minute* 8' x 10' 3 Hour 8' x 10' 3 Hour 8' x 10' 9849-F 9949-F Metal — — — — — 90 Minute* 8' x 10' 3 Hour 8' x 10' 3 Hour 8' x 10' 9849LBL-F 9949LBL-F Metal — — — — — 90 Minute* 8' x 10' — 3 Hour 8' x 10' * Currently, no door manufacturers offer a listing over 90 minutes with doors swinging same direction. Consult wood door manufacturers for current UL listings. 72• Von Duprin 98/99 Series 72 * 98/99 Finishes A. Center case cover B. Touch bar end cap C. Touch bar trim D. Cover plate E. Mechanism end cap F. Mechanism case Finishes US number BHMA number A, B, E C D&F Bright brass US3 605 Bright brass Bright brass US3, 605 Buffed anodized Satin brass US4 606 Bright brass Satin brass US4, 606 Anodized Satin bronze US10 612 Plated Satin bronze US10, 612 Anodized Bright chrome US26 625 Plated Bright stainless steel US32, 629 Buffed anodized Satin chrome US26D 626 Plated Satin stainless steel US32D, 630 Anodized Satin stainless steel* US32D 630 Stainless steel Satin stainless steel US32D, 630 Anodized Aluminum, anodized US28 628 Powder coat Satin stainless steel US32D, 630 Anodized Duranodic dark bronze 313 710 Powder coat Powder coat Powder coat Black 315 622 Powder coat Powder coat Powder coat Special Finishes Color US number BHMA number A, B, E C D&F Satin bronze, oil-rubbed US10B 613 Oil-rubbed, US10B Oil-rubbed, US10B Powder coat Powder coat** RAL # – Powder coat Satin stainless steel US32D, 630 Powder coat (unless specified to match device) Bright bronze US9 611 Plated Bright bronze US9, 611 Buffed anodized Satin nickel * US15 619 Plated, clear powder Satin stainless steel US32D Anodized Aged bronze 643E – – Relieved aged bronze Relieved aged bronze Aged bronze, no relief Satin chrome (antimicrobial) U26D-AM 626-AM AM Clear over chrome AM Clear over satin stainless steel US32D, 630 AM Clear over anodized Satin stainless steel (antimicrobial) US32D-AM 630-AM AM Clear over stainless steel AM Clear over Satin Stainless Steel AM Clear over US32D, 630 anodized Finishes Color Touch bar trim options — Knurled Embossed “Push” Braille (Caution-Stairwell), satin stainless steel only RSS, US32D only, red silk screen lettered “EMERGENCY EXIT ONLY – PUSH TO OPEN AND SOUND ALARM.” * US32D and US15—available on 98 Series only ** Other custom logo touchbar trim and RAL color combinations available - consult factory 73 Von Duprin 98/99 Series • 73 98/99 Finishes Finishes* US number BHMA number Color US number BHMA number Chromium, polished US26 625 Bronze, dull US10 612 Anodized, aluminum US28 628 US15 619 Chromium, dull US26D 626 Satin stainless steel US32D 630 Brass, polished US3 605 Duranodic dark bronze 313 710 Brass, dull US4 606 Black 315 711 Finishes Color Satin nickel Available for 35A ONLY Special finishes Color US number BHMA number Satin chrome, Antimicrobial US26DAM 626-AM Satin stainless steel, antimicrobial US32DAM 630-AM Aged bronze 643e – – Pushpad options — Knurled Embossed “Push” Braille (Caution-Stairwell), satin stainless steel only RSS – (Emergency Exit – Push to open and sound alarm) – Red Silkscreen lettering on US32D * Note: Durable powder coated finishes available at specific special request. PLEASE CONTACT FACTORY. 74• Von Duprin 98/99 Series 74 About Allegion Allegion (NYSE: ALLE) creates peace of mind by pioneering safety and security. As a $2 billion provider of security solutions for homes and businesses, Allegion employs more than 8,000 people and sells products in more than 120 countries across the world. Allegion comprises more than 25 global brands, including strategic brands CISA®, Interflex®, LCN®, Schlage® and Von Duprin®. For more, visit www.allegion.com © 2015 Allegion 006590, Rev. 07/15 www.allegion.com/us
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Create Date : 2015:08:13 11:47:47-04:00 Creator : Adobe InDesign CS6 (Macintosh) Modify Date : 2015:12:04 15:27:13-05:00 XMP Toolkit : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15 Metadata Date : 2015:12:04 15:27:13-05:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Instance ID : uuid:a109c80e-f916-47f4-a9fd-4ed420712123 Original Document ID : xmp.did:5DF51FCC472168118A6DCBE4F6556AD0 Document ID : xmp.id:0D262E16D0206811822ABDB27CF85060 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:3271C79B42206811822ABDB27CF85060 Derived From Document ID : xmp.did:42DE10F144206811822ACD9FBB41E3CD Derived From Original Document ID: xmp.did:5DF51FCC472168118A6DCBE4F6556AD0 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2015:08:13 11:47:47-04:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 76EXIF Metadata provided by EXIF.tools