Von Duprin LBR Auxiliary Fire Pin And 499F Strike Installation Instructions 107570
User Manual: Von Duprin LBR Auxiliary Fire Pin and 499F Strike Installation Instructions Installation Instructions
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
LBR 911010-00 Fire Pin/Strike Kit Installation Instructions LBR (Less Bottom Rod) ! WARNING For surface vertical rod installations, incorrect strike installations can result in latching failure in a fire condition. This can result in severe injury or death. Installer: Discard installed strikes and replace with correctly installed 499F strikes supplied with this kit. Failure to install the 499F strikes on Surface Vertical Rod LBR-F devices will void the UL Fire Label. Important: Read this first! 1. LBR Fire Pin/Strike Kit is for use only with Von Duprin 98/9927-F, 98/9947-F, 33/3547-F, 33/3527A-F, 33/3547A-F, and 2227-F devices. 2. Any door preparation must be performed by an installer that is certified by the door manufacturer. 3. Installation of device with 499F strike for surface vertical rod devices, and 338 strike for concealed vertical rod devices is required to maintain fire listing. For 499F installation, see page 3 of these instructions. Parts List Description Quantity Auxiliary Fire Pin Assembly 1 #6 x 3/4” Sheet Metal/Wood Flat Head Screw 4 Strike Hole Plug 1 499F Strike Assembly 2 Return Spring 2 Centercase Hole Plug 2 ! NOTE One (1) auxiliary fire pin assembly is supplied with two LBR devices. It does not matter which door leaf the auxiliary fire pin is installed on. However, the pin must be installed to maintain the fire listing. The purpose of the auxiliary fire pin assembly is to keep the doors in alignment during a fire. In a fire, the bolt extends from the auxiliary fire pin into the strike hole in the opposite door leaf. The black cap visible on the face of the auxiliary fire pin and the strike hole plug must melt in order for the bolt to extend. If an Edge Guard is used, make sure it is modified to allow clearance for the Fire Pin and Plastic Cap to be mounted to the door edge after the Edge Guard is installed. See Edge Guard Preparation on page 4 for more information. INSTALLATION 1 Prepare auxiliary fire pin mounting hole, screw holes, and strike hole in door. 1 3/4" depth of hole CLdoor 3 3/8" depth of hole CLdoor 1/4" #36 drill 4 places 1/4" 5/8" 7/8" dia. CL CL 1" dia. 5/8" 6" from bottom of door Strike Hole Plug Door Leaf 2 CLdoor CLdoor Auxiliary Fire Pin Door Leaf Install strike hole plug and auxiliary fire pin. Install strike hole plug in strike hole Mount auxiliary fire pin with four #6 x 3/4" Type AB flat head screws 2 3 Install 499F strike. NOTE The 499F strike installation is only for 98/9927-F-LBR, 33/3527A-F-LBR, and 2227-F-LBR devices. For concealed vertical rod LBR devices, skip this procedure. 3.1. Replace 299F strikes with 499F strikes as shown below. 3.2. Adjust 499F strike to position shown in Figure 3-1. 3.3. Install remaining three screws (see Figure 3-2). 3.4. Prepare door for strike hook (see Figure 3-3) and install strike hook. Figure 3-4 shows relative positions of strike, strike hook, and top latch. Strike roller 1/16" ref. #25 drill and #10-24 tap (3 places) Figure 3-1 Figure 3-2 Hole Schedule Metal door: #7 drill and #1/4"-20 tap Wood door: 13/32" dia. drill thru Remove 299F strike Strike hook Face of stop Bottom of stop 1/16" Face of door CL strike Strike Center strike hook on strike, locate to 1/16" dimension, and mark holes Figure 3-3 Strike hook Figure 3-4 3 EDGE GUARD PREPARATION If using Edge Guards, clearance holes must be cut into Edge Guards before they are installed on door as shown in Figure 4-1. Outer Dimensions of plug and strike Edge Guard clearance holes 1.188" 1.765" 1.000" Figure 4-1 Edge guard near exit device center case can extend no further than .0625" from edge of door, as shown in Figure 4-2, or interference with device center case could occur. If Edge Guard is wider than specified, it may need to be trimmed in that area to clear center case. Edge of door Maximum .0625" from edge of door to edge of device Figure 4-2 4 RETURN SPRING REPLACEMENT ! WARNING Installation of the wrong spring can result in latching failure in a fire condition. This can result in severe injury or death. Installer: Make sure correct return spring is installed per instructions below. 1 Determine which spring the device baseplate contains comparing to the following two springs: Spring A ! NOTE If device contains Spring "B" skip to Step 3. Spring B 9927-F 2 Remove return spring "A" and replace with spring supplied in kit. 3 Repeat steps 1 and 2 for device on other door leaf. 4 Reinstall devices. 5 VERTICAL ROD ADJUSTMENT PROCEDURE 33/3527A-F-LBR, 98/9927-F-LBR, & 2227-F-LBR 1 Screw top vertical rod to top latch case. 2 Push rod upward slowly until it has fully extended top latch bolt to achieve deadlocking as shown. 3 Adjust top vertical rod until rod snaps into centercase. 3/16" 4 6 Hold down Push to check deadlocking Check device operation by opening and closing door with outside lever or thumbpiece. VERTICAL ROD ADJUSTMENT PROCEDURE 33/3547A-F-LBR & 98/9947-F-LBR 1 Loosen top adjustment lock screw. 2 Rotate adjusting screw clockwise until centercase adjustment block begins to move down and top latch bolt is fully extended (do not remove retaining clip). 3 Set adjusting screw as shown. Tighten adjustment lock screw. Top Rod (9947-F shown) Depress to check deadlocking Centercase Adjusting Screw Retaining Clip Depress in hole with screwdriver to release latch bolt Top rod assembly Touch Bar Adjustment Lock Screw on Flat Centercase Adjustment Block 4 Rod Actuating Link (9947-F shown) Check device operation by opening and closing door with outside lever or thumbpiece. 7 VERTICAL ROD ADJUSTMENT PROCEDURE 3347F-LBR 1 Loosen top adjustment linkage screw on top connector as shown in the diagram. 2 Fully extend latch bolt. Retighten top adjustment linkage screw. 3 Open door and release pushbar. Top latch bolt should be held retracted. 4 Release latch bolt as shown. 5 Check deadlocking. Depress to check deadlocking Depress in hole with screwdriver to release latch bolt Teeth must mesh properly Top Adjustment Linkage Screw Touch Bar 6 Check device operation by opening and closing door with outside lever or thumbpiece. Customer Service 1-877-671-7011 www.allegion.com/us © Allegion 2015 Printed in U.S.A. 911010-00 Rev. 06/15-e
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.5-c021 79.153613, 2013/07/11-05:21:54 Format : application/pdf Subject : Description : 98/99 Series;exit devices;Exit Device Options;98/9927-F;.98/9947-F;98/9949-F;98/9950WDC-F;33/3547-F;33/3527A-F;.33/3547A-F;33/3549A-F;33/3550AWDC-F;2227-F Modified : 2016:01:04 18:08:16Z Title : Von Duprin LBR Auxiliary Fire Pin and 499F Strike Installation Instructions Size : 154027 Author : jtellis Extracted : 2016:12:06 22:24:41Z Sha 1 : 0102468aaf4d389a0716bafc825a877fc891d56c Modify Date : 2015:06:08 17:39:37Z Create Date : 2015:06:08 17:39:37Z Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 11.0 (Windows) Instance ID : uuid:55654bd1-6e88-46ce-b8ce-72127ab215c0 Document ID : uuid:5e0b1c50-8a56-4484-ab19-d76b35c21acf Page Count : 8 Creator : PScript5.dll Version 5.2.2 Keywords : 98/99, Series;exit, devices;Exit, Device, Options;98/9927-F;, 98/9947-F;98/9949-F;98/9950WDC-F;33/3547-F;33/3527A-F;, 33/3547A-F;33/3549A-F;33/3550AWDC-F;2227-FEXIF Metadata provided by EXIF.tools