Voxx Accessories PNP100 Projector Bluetooth Speaker User Manual

Voxx Accessories Corp. Projector Bluetooth Speaker

User manual

What’s in the box?(1) Projector (1) Power adapter (3) Image wheels2. LOAD AN IMAGE WHEEL 3. TURN ON THE PROJECTORGetting started1. PLUG IN THE PROJECTORPlug the right-angle end of the power adapter into the DC IN jack on the bottom of the projector. Run the cable through the cable trough on the bottom of the projector. Then place the projector on a flat surface.Plug the other end of the power adapter into a working outlet or surge protector.Bottom of the projectorCable troughOn the back of the projector, slide the image wheel door into the FOR DISC ACCESS position.Take out the wheel drawer above the image wheel door.Please an image wheel on the wheel drawer. Make sure the UP label is facing up.Put the wheel drawer back into the image wheel door.Slide the image wheel door up, into the FOR PROJECTION position.IMPORTANT: The projector will not illuminate unless the image wheel door is in the up (FOR PROJECTION) position.Back of the projectorImage wheel door (down position)Wheel drawerTo turn the projector on: Press the PROJECTOR button on the front of the projector. To adjust brightness of the projector (or turn it off): Press the PROJECTOR button repeatedly to cycle through the settings (high, medium, low, and off).4. ADJUST THE PROJECTOR POSITIONFront of the projectorMake sure the image wheel door on the back of the projector is in the FOR PROJECTION position (pushed up). Pull the projector lever below the image wheel door to adjust the projector position so that it points where you want. Image wheel door (up position)Back of the projectorProjector leverEveryday usePLAYING SOUNDSThe Project Nursery Sight + Sound Projector offers a variety of soothing lullabies and nature sounds, as well as white noise, to calm baby.To cycle through these sounds: Press the SOUND button on the front of the projector. Each press goes to a different selection. To adjust the volume: Press the VOLUME – or + button.To turn sounds off: Press the SOUND OFF button on the top of the projector Front of the projector
Quick Start GuidePAIRING WITH YOUR PHONE (BLUETOOTH)The Project Nursery Sight & Sound Projector can also play music from your smartphone or other Bluetooth device. Here’s how to set it up.Press and hold the BLUETOOTH button on the front of the projector until the indicator light next to this button starts blinking.Enable Bluetooth on your smartphone or other device (if it isn’t already enabled).USING THE TIMERFront of the projectorIndicatorChoose “Sight+Sound” from the list of pairing options on your smartphone. (If it’s not in the list, choose “Scan” from your phone’s Bluetooth menu.)The speaker gives an audio signal when it’s finished pairing and connecting to your smartphone. The indicator turns solid blue.Note: The process of enabling Bluetooth and connecting varies from device to device. See your device’s owners manual for more information and specific instructions.Bluetooth Wireless Connection Tips• Make sure the Bluetooth capability of your device is turned on.• The Bluetooth wireless connection works up to a range of roughly 33 feet (10 meters). This range may vary, however, based on other factors, such as room layout, wall material, obstacles, your device’s Bluetooth performance, etc. If you’re having problems connecting to this speaker, move closer to it. • If your device asks you for a password to connect, use “0000”.Front of the projectorThe timer shuts the projector and sound off automatically after a set amount of time. To set the timer: Press the TIMER button on the front of the projector. The TIMER indicator on the top front of the projector shows the amount of time on the timer: 15, 30, or 60 minutes. Press TIMER to cycle through these options or turn the timer off.USING THE LIGHTThe front of the Sight & Sound Projector offers soft area illumination in three levels of brightness, to complement the projector lighting. To turn the light on: Press the LIGHT button on the front of the projector. To adjust or turn off the light: Press the LIGHT button repeatedly to cycle through the settings (high, medium, low, and off). Front of the projectorQuestions?Just call 1-844-393-7338 or visit ProjectNursery.com©2016 Voxx Accessories Corp. 3502 Woodview Trace, Suite 220 Indianapolis, IN 46268 PNP100 QSG 00

Navigation menu