Voxx Electronics AESTG34 Security/Remote Control Transmitter User Manual PUB2007014V00R02
DEI Headquarters, Inc. Security/Remote Control Transmitter PUB2007014V00R02
UserManual.wiki
>
Voxx Electronics
>
AESTG34 User Manual
user manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![6 THE 2 WAY XRT REMOTE CONTROL The remote control can access four distinct remote starters. A maximum of four remote controls can be assigned to your vehicle. See your dealer for additional remote controls. NOTE: The range of your remote control can be affected by a weak battery, interference from nearby metal structures, hydro poles, or crowded parking lots. USING YOUR REMOTE CONTROL To send a command, press for two seconds on the appropriate button. Command may not be sent if the button is not pressed long enough. The remote control beeps when a button is pressed, then emits eight short beeps during the transmission, i.e. about one second after the button was pressed. Your remote control can transmit on four different channels, allowing control of four separate vehicles. Only the “Panic” command is transmitted on both channels simultaneously. To select a different channel, press the “P” button located on the back and hold it for 2 seconds, when the button is released the transmitter passes to the next channel. The remote control shown may differ from that included in the kits. Your system may be programmed in such a way that it can distinguish between two groups of remote controls (maximum: two remotes per group). These groups let you activate predefined settings (seat, mirror and other) when unlocking certain vehicles (additional optional equipment required). As soon as a command is sent, the remote switches over to standby mode in order to receive and display confirmations sent by the command module installed in the vehicle. These confirmations are sent to all the programmed remote. These signals are transmitted only once and could be neutralized by radio or electromagnetic interferences generated by electronic devices in the vicinity. If no confirmation is received in a given location, move away from electronic devices and activate the "Status" command (). The start module will inform you of the status of door locks, alarm, and running of the engine. Note that the communication between the vehicle and the transmitter operates in only one direction at a time. This is why it is recommended to wait for the confirmation before sending another command. Otherwise, the vehicle and the transmitter could transmit at the same time wich would block the command as well as the returned confirmation. Out of range If the vehicle is out of range, the transmitter will emit a soft chirp after 3 seconds to indicate that the command has not been received by neither the module nor the transmitter. REPLACING THE BATTERY The LCD of the 4-button remote has a battery icon telling you when to replace the battery. We strongly recommend keeping a replacement battery in your glove compartment. The remote controls require one AAA battery. See your dealer for spare batteries. To replace the battery, slide the latch sideways and remove the battery cover on the back of the remote control case, remove old battery and replace it with a new one. Make sure the battery is placed the right way (see pictogram inside the cover). Commentaire [c1]: Verifier avec Marc pour etre sure qu’il ne confond pas avec le délais de confirmation. Les commandes tels lock recoivent un feedback instantanné mais je doute qu’il est mis a jour si elle ne recoit pas ce feedback](https://usermanual.wiki/Voxx-Electronics/AESTG34/User-Guide-858823-Page-30.png)
![7 CONFIRMATIONS EMITTED BY THE REMOTE An audible confirmation (piezo) and a visual confirmation (LCD display) are emitted each time a command is transmitted. The LCD displays the vehicule status at all time, the display is refreshed on every transmission or when the status of the vehicle changes pertaining that the “Status confirmation” function is enable. The display shows the last confirmation received. The following diagram shows the usefulness of each icon of the display. Descriptions in CAPITAL letters show confirmations pertaining to the security system’s functions. 1 2 3 4 5 615242322212019181789101112131614257 1 Transmission 14 Battery charge indicator 2 Vehicle out of range 15 Auxiliary outputs status 3 Reception 16 Sentinel mode status 4 Unlocking 17 SECURITY SYSTEM STATUS 5 Locking 18 ULTRASONIC SENSOR 6 PRE-ALERTMD 19 IGNITION STATUS SENSOR 7 Panic / PRE- ALERTMD / ALARM 20 TILT SENSOR 8 ALARM 21 Remote starter status 9 SHOCK SENSOR 22 HOOD STATUS 10 FEILD DISTURBANCE SENSOR 23 TRIGGERED ZONES 11 TRUNK LID STATUS 24 Valet mode status 12 GLASS BREAKAGE SENSOR 25 Vehicle identification 13 DOORS STATUS Two types of confirmations are displayed on the remote : Command confirmation: These confirmations are command acknowledgement, the icon corresponding to the command is displayed to confirm reception of the command. Status confirmations : These confirmations are displayed when the status of a zone, monitored by the system, changes. i.e. : door opening, security system alarm state, etc. Command confirmations are returned immediately following a command transmission whereas the status confirmations may be returned up to 12 seconds after the event appended depending on the communication protocol between the hand-held unit and the vehicle. Remarks: When the remote receives a confirmation that is intended to a vehicle other that the one actually selected, most audible confirmations are made more discrete, vehicle icon flashes (1-4) to warn you that the display reflect the status of that specific vehicle. When a command is transmitted, the vehicle selection gets back to the previously selected unless the confirmation was related to an alarm condition. In that case the selected vehicle is temporarily changed, to allow stopping the alarm condition without having to change the vehicle selection, then gets back to previously selected when the alarm condition is stopped. Out of range : In the event that the environment prevents the confirmation from being received by the remote control, all icons are cleared out. In this case, resend the command or send the status command to refresh the display. Commentaire [c2]: Verifier le terme. Commentaire [c3]: Traduction](https://usermanual.wiki/Voxx-Electronics/AESTG34/User-Guide-858823-Page-31.png)
