WIESON Technologies TPMS-8300 Tire Pressure Monitoring System User Manual

WIESON Technologies Co., Ltd. Tire Pressure Monitoring System

User manual

SC-T8000 Series TPMS Fast Installation Guide Bluewave Technology Co., LTD. Tel: 886-2-23451989 Fax: 886-2-23450177 2F.-1, No.5, Lane 178, Jhuangjing Rd., Sinyi District, Taipei City 110, Taiwan, R.O.C. http://www.7brains.com/ Email: support@7brains.com 2007/4/18
─────────────────────────────── SC-T8000 Fast Installation Guide Installation 1. Check Components Receiver(Passenger) Receiver(Truck) T-Type Sensor Receiver Sensor SC-T8000 1 4 SC-T8060 1 6 SC-T8080 1 8 SC-T8100 1 10 SC-T8120 1 12 One Power Cord One Sucker & Fixture * attention: Four-wheeled passenger and truck’s receivers are different. Please check the left-circle of receiver. 2. Check Sensor Identification Number (Sensor ID) and Set 2.1 Each sensor should be assigned a unique identification number (ID) which was marked on the top of sensor. 2.2 The last two number of sensor ID has given the locating tire position, the order is as following: * SC-T8000 ID locating position 01:left-front tire 02:rght-front tire 04:left-rear tire 03: right-rear tire SC-T8060 ID locating position 01:left-front tire 02:right–front tire 05:left-rear tire right 03:righr -rear tire right 06:left-rrear tire left 04:righr-rear tire left 3. Install the Sensor into Wheel 3.1 Screw down the original valve cap. 3.2 Follow the ID’s last two number to install the right tire (please refer to the 2.2 illustration) Note: Since sensors being electric isolation processed before shipping, it is recommended, for the first installation, to rotate sensor forward and backward several times to remove isolation coating and ensure the conductivity between sensor and valve stem. 3.3 Screw fixture: Prevent sensor from easy removing also in favor of sensor Welcome to Bluewave Super Cat T-Type 8000 Series Tire Pressure Monitoring System (SC-T8000 TPMS). This Fast installation Guide is intended to give you a fast overview of the key steps required to install your SC-T8000 Series TPMS. For more detailed information, please refer to the SC-T8000 Series TPMS User’s Manual.(http://www.7brains.com)
─────────────────────────────── SC-T8000 Fast Installation Guide stationary. Note: (1) User may ignore this fixture, when causing inflation hassle concerns. (2) To ensure LED template display correctly coincide with actual sensor position, Please follow step 4-Sensor alignment in order to get right pressure and temperature from right sensor. 4. Sensor alignment Plug the attached power cord into cigarette lighter directly, then activate the receiver. 4.1 Operation mode illustration SC-T8000 series provides various operating mode to set different parameter, under normal condition, please follow the above illustration“Key4（Exit）for 0.5 second into different operating modes in order to make use of different functions and parameter sets. 4.2 Preset ID Under normal condition，press ，check the first installed tire ID is righr or not, and then press Enter , check tire ID 2, 3, and 4. If the sensors ID are all correctly located, then you can ignore the next steps. (Section 4.3). 4.3 ID search and set under normal condition，do as the followings: à Press (for 0.5 second) à Press twice à Press into ID search Make sure the sensor is consistent with the main engine geared position then press Key1 (Enter),
─────────────────────────────── SC-T8000 Fast Installation Guide follow step 3 to install the next sensor installation, after finishing press Key4 (Exit). *attention: Finished installing, LED shows “red “, If you set different sensor ID in the same place, the LED will disappear, at this moment you must reset the sensor. 〔Signal〕 1. Normal: When tires operate in normal condition, LED shows “green” light. Every 8 sec., the “orange” light takes turn to show each tire’s condition. 2. Abnormal: When tire is in over-heated, over-pressured, or under-pressured condition, LED shows “red” light, locks on the position of over-heated tire with “beep” sound. ＊NOTE：Two tires are abnormal at the same time, it will be fixed on the abnormal status. 3. Receiver did not receive Data: If receiver can not receive updated tire messages over 10 mins., LED shows abnormal indication. Example: Left-front tire didn’t receive data, shows “ t l ----”. Right-front tire didn’t receive data, shows “ t2 ----”. Left-rear tire didn’t receive data, shows “ t3 ----”. Right-rear tire didn’t receive data, shows “ t4 ----”. *attention: The abnormal signal will be disappear after once messages received. If long time no new information, please check your sensor. 〔FCC Notice〕 The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. THIS DEVICE COMPLIES WITH PART 15 OF THE FCCRULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Caution: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
910805 2FCC Notice: Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu