WINIA Electronics 7NFCMC529B User Manual 529B EN

Dongbu Daewoo Electronics Corporation 529B EN

Users Manual

Model No : 529BCOLOR MONITORUSER’S GUIDE
1. Read all of these instructions.2. Save these instructions for later use.3. Unplug this monitor from thewall outlet before cleaning. Do notuse liquid cleaners or aerosolcleaners. Use a damp cloth forcleaning.4. Do not use attachments not recommended bythe monitor manufacturer as they may causehazards. 5. Do not use this monitor near water, e.g., near abathtub, washbowl, kitchen sink, or laundry tub,in a wet basement, or near a swimming pool, etc. 6. Do not place this monitor on anunstable cart, stand, or table. Themonitor may fall, causing seriousinjury to a child or adult, andserious damage to the appliance. 7. Slots and openings in thecabinet and the back or bottom areprovided for ventilation, to ensurereliable operation of the monitor,and to protect it from overheating.These openings must not be blocked or covered.The openings should never be blocked byplacing the monitor on a bed, sofa, rug, or othersimilar surface. This monitor should never beplaced near or over a radiator or heat register.This monitor should not be placed in a built-ininstallation such as a bookcase unless properventilation is provided.8. This monitor should be operatedonly from the type of power sourceindicated on the marking label. Ifyou are not sure of the powersupplied to your home, consultyour monitor dealer or local power company.9. This monitor is equipped with a3-wire grounding-type plug, Thatis, a plug having a third(grounding) pin. This plug willonly fit into a grounding-typepower outlet. This is a safety feature. If you areunable to insert the plug into the outlet, contactyour electrician to replace your obsolete outlet.Do not defeat the purpose of the grounding-typeplug. 10. Do not allow anything to reston the power cord. Do not locatethis monitor where the cord will beabused by people walking on it. 11. Follow all warnings and instructions markedon the monitor. IMPORTANT SAFEGUARDS12. For added protection for thismonitor during a lightning storm,or when it is left unattended andunused for long periods of time,unplug it from the wall outlet. Thiswill prevent damage to the monitor and/or thecomputer due to lightning and power line surges. 13. Do not overload wall outlets and extensioncords as this can result in fire or electric shock. 14. Never push objects of any kind into thismonitor through cabinet slots, as they may touchdangerous voltage points or short out parts thatcould result in a fire or electric shock. Never spillliquid of any kind on the monitor. 15. Do not attempt to service thismonitor yourself, as opening orremoving covers may expose youto dangerous voltages or otherhazards. Refer all servicing toqualified service personnel. 16. Unplug this monitor from the wall outlet andrefer servicing to qualified service personnelunder the following conditions: a. When the power cord or plug is damaged orfrayed. b. If liquid has been spilled into the monitor. c. If the monitor has been exposed to rain orwater. d. If the monitor does not operate normally byfollowing the operating instructions. Adjust onlythose controls that are covered by the operatinginstructions, as improper adjustment of othercontrols may result in damage and will oftenrequire extensive work by a qualified technicianto restore normal operation. e. If the monitor has been dropped or the cabinethas been damaged. f. When the monitor exhibits a distinct change inperformance, this indicates a need for service. 17. When replacement parts arerequired be sure the servicetechnician has used replacementparts specified by the manufacturerthat have the same characteristics asthe original part. Unauthorized substitutionsmay result in fire, electric shock, or otherhazards. 18. Upon completion of any service or repairs tothis monitor, ask the service technician toperform routine safety checks to determine thatthe monitor is safe to operate. FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENTNOTE : This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses andcan radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cuase harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio or TV technician for help. CAUTION : Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authorityto operate the equipment. CANADIAN DEPARTMENT OF COMMUNICATIONSCOMPLIANCE STATEMENTThis digital apparatus does not exceed the Class A/Class B (whichever isapplicable) limits for radio noise emissions from digital apparatus set out inthe Radio Interference Regulations of the Canadian Department ofCommunications. Avis de conformité aux normes du Ministère des Communications duCanada.Le present appareil numérique n’emet pas de bruits radioélectriquesdepassant les limites applicables aux appareils numériques de Class A/deClass B (selon le cas) prescrites dans le règlement sur le brouillageradioélectrique édicte par le ministère des communications du Canada.
Bitte lesen Sie alle diese Informationen, bevor Sie das Gerät inBetrieb nehmen! Lesen Sie sich außerdem dieBedienungsanleitung komplett und sorgfältig durch, da nur indiesem Fall eine problemlose Inbetriebnahme erwartet werdenkann. •Achten Sie darauf, daß das Gerät nur in eine 230V Schuko-Steckdose eingesteckt wird. •Die Steckdose sollte jederzeit frei zugänglich sein um beieinem evtl. auftretenden Notfall das Gerät schnell vom Netzzu trennen. •Achten Sie desweiteren darauf, daß die Netzanschlußleitungnicht mechanisch beansprucht oder sonstwie beschädigtwird. •Offnen Sie das Gerät niemals! Im Inneren befinden sichTeile mit gefährlicher Spannung. •Bevor Sie das Gerät reinigen, ziehen Sie bitte denNetzstecker aus der Steckdose. Säubern Sie dann das Gerätmit einem feuchten (keinesfalls tropfnassen) Lappen. •Die in diesem Gerät entstehende Röntgenstrahlung istausreichend abgeschirmt (Ortsdosisleistung in 0.1mAbstand weniger als 1.0µ Sv/h). Beschleunigungsspannungmaximal 25kV. •Stellen Sie das Gerät an einem ergonomisch günstigen Ortauf und sorgen Sie dafür, daß der Monitor mit nach GS-VW-SG7 geprüfter Peripherie betrieben wird, da nur unterdiesen Umständen ein optimaler ergonomischer Betrieb desGerätes sichergestellt ist. Falls Sie dennoch Fragen haben, auf die dieBedienungsanleitung keine hinreichende Antwort geben kann,so kontaktieren Sie bitte den nächsten Fachhändler. Maschinenlärminformationsverordnung 3. GSGV, 18.01 1991:Der arbeitsplatzbezogene Schalldruckpegel beträgt 70 dB (A)oder wenigergemäß ISO 7779. DECLARATION OF CONFORMITYWe, Manufacturer / Importer DAEWOO ELECTRONICS CO., Ltd 541, 5-Ga, Namdaemoon-Ro, Jung-Gu Seoul, Korea declare under our sole responsibility that the product, Color Display monitor 529Bto which this declaration relates is in conformity with the following standard(s) or other normative document(s) Safety : EN60950/1992/A1:1993/A2:1993 A3:1995/A4:1997EMC : EN 55022/8.1994, EN 50082-1/1992EN 60555 Part 2, 3/1987following the provisions of 89/336 EEC-EMC Directive and the provisions of 73/23 EEC-Low Voltage Directive. Handed over by : S.Lee, Managing Director. Display Business Division June, 1999 Seoul Signature: S.Lee, Managing Director. Display Business Division. DAEWOO ELECTRONICS Co., Ltd WICHTIGE INFORMATIONEN
Emission Characteristics Tested by SEMKOA sample of this type has been tested and has showncompliance with the guidelines in the swedish documentMPR II.This product is also designed for IT power system with phaseto phase voltage of 230V. The power cord is used as a main disconnect device.Disconnect the power cord before servicing. The outlet mustbe installed near the monitor and must be easily accessible.As an ENERGY STAR Partner, Daewoo Electronics Co., Ltd.has determined that this product meets the Energy Starguidelines for energy efficiency.The appliance is not intended for use by young children orinfirm persons without supervision ;Young children should be supervised to ensure that they do notplay with the appliance.
This manual explains how to correctly install, operate,and get the best performance from your monitor. Pleaseread this user’s guide carefully before installing yourmonitor, then keep it near your monitor for quickreference. First, please check that the contents of the boxcorresponds with the following checklist :•Color monitor •Power cord •User’s Guide •Tilt/swivel stand •Warranty Card (Optional)If any item is missing or damaged, please contact yourdealer. Please keep the box and packing materials so thatyou may properly store or transport your monitor.English-1CONTENTS INTRODUCTIONIntroduction ............................................................ 1Product Features ................................................ 2Setup ........................................................................ 3Installing the Tilt/Swivel Stand ......................... 3Connecting the Signal Cable and Power Cord .. 4Power Management System .............................. 5Display Data Channel for Plug and Play ........... 5Operation and Adjustment ................................... 6Specifications ........................................................ 10Factory Preset Timings ........................................ 10Troubleshooting .................................................... 11AppendixDescription for D-sub Connector
INSTALLING THE TILT/SWIVEL STAND1. Ensure that the power is off to the monitor. 2. Set the monitor face down with the underside facingyou. Please be careful not to scratch the monitorscreen. 3. Align the four hooks on the stand with the guide holeson the bottom chassis of the monitor. 4. Insert the hooks into the guide holes. 5. Slide the tilt/swivel stand toward the front of themonitor until the latch locks in position. 6. Turn the monitor and the stand upright.English-3PRODUCT FEATURES •The convenient and user-friendly on-screen displayallows for easy and accurate adjustments of horizontaland vertical screen size and position, geometry, andscreen color. •The monitor supports a safe working environment instrict compliance with the MPR II standard for lowemissions.•The monitor complies with the VESA Display DataChannel (DDC) specification for Plug and Playcompatibility. Advanced microcircuitry makes setupand configuration fast and effortless. •The monitor features Advanced Color Controls forfine-tuning to meet your own personal tastes orapplication requirements. Use the on-screen controlsto adjust the color temperature, RB gain value for thebest possible screen color and intensity. •Press the menu button and activate the Self-Diagnosismenu to determine whether your monitor isfunctioning normally, not receiving a signal or isreceiving a signal that is out of scanning range.•Activate the higher refresh rates of the monitor tostabilize the screen and eliminate the annoying flickerthat contributes to eye-strain and headaches. •The “borderless” full-screen display capability worksunder all graphic modes and provides a larger viewingarea than conventional monitors, giving you a betterpicture with more workspace. English - 2SETUPLatchIf you want to remove the tilt/swivel stand on the monitor,press the latch and pull the tilt/swivel stand toward theback of the monitor. Lift the stand to separate.
English-5POWER MANAGEMENT SYSTEMIf you use the monitor with a computer that complieswith the power-saving program, you can set the monitorto go blank when the system has remained unused for aperiod of time. To specify the period or to disable thisfeature, set the system timeout field of the computer’ssystem setup program or use special software for power-saving. See the computer user’s manual for the details ofusing the system setup. While the monitor is in power-saving mode (blank screen), it consumes less power thanwhen it is in its normal state. The color of the powerLED will indicate the state. To restore the screen image,press any key of your keyboard or move your mouse. Ifthe signal cable is connected loosely or disconnected, thepower-saving feature will not operate.DISPLAY DATA CHANNEL FOR PLUG ANDPLAYIf you use the monitor with a computer that complieswith DDC1/2B/CI of VESA, the host video cardautomatically configures itself without your interventionin a way that best fits the attached monitor. The DisplayData Channel(DDC) allows the monitor to inform thehost system about configuration information for optimumuse of the monitor. Use of the video card utility is notrequired to match the resolutions and refresh rates of themonitor and video card.CONNECTING THE SIGNAL CABLE ANDPOWER CORD1. Turn off the computer and monitor.2. Connect the 15 pin D-sub connector to the output port ofthe video card in your computer.3. Tighten the screws of the connector.4. Plug the power cord into the AC receptacle located onthe back of the monitor. 5. Plug the other end of the power cord into the AC outlet.English - 4Signal CablePower CordIf your power cord is PC-to-Monitor type, plug theother end of the power cord into the AC receptacle inthe computer.
English-7English - 6Key ProcessMENUStart •When you choose the icon on the OSD window, youcan exit the OSD screen. Hot KeyBRIGHTNESS CONTRASTOPERATION & ADJUSTMENTControl Panel•Move cursor to the right window on the OSDwindow.•Increase the value of any selected function.•Move cursor to the left window on the OSDwindow.•Decrease the value of any selected function.•Launch OSD(On-Screen Display) MENU window.•Move cursor to the high window on the OSDwindow.•Increase the value of V.size or V.center.•Move cursor to the low window on the OSDwindow.•Decrease the value of V.size or V.center.
ICON CONTROL FUNCTIONSEnglish-9English - 8Adjust the width (horizontal size) and theheight (vertical size) of the display.Display horizontal & vertical frequencyand polarity.Degaussing keeps the monitor free fromunwanted magnetism that can result incolor impurity.H. SIZE & V. SIZEDEGAUSSSTATUSSelect language for OSD (5 languages).Reset the screen to the Factory PresetDisplay Settings.LANGUAGERECALLOSD FunctionsAdjust the left and right margins for moreconvex or more concave margins.Adjust the trapezoid of the screen bymoving the lines inward or outward.PINCUSHIONTRAPEZOIDChoose different preset colortemperatures or set your own customizedcolor parameters.Adjust the red gain.Adjust the position of the displayhorizontally (left or right) and vertically(up or down).H. CENTER & V. CENTER COLOR TEMPRED GAINAdjust the blue gain.BLUE GAINAdjust the parallelogram when the screenis leaning left or right.PARALLELOGRAMSelf DiagnosisWhen the monitor doesn’t display, if you press any key,Self Diagnosis screen is displayed. Self Diagnosisfunction checks if the status of the monitor is No Signalor Out of range.No Signal screen is displayedwhen the D-Sub signal connectoris not connected or the status ofthe monitor is on DPMS mode.Out of Range screen is displayedwhen the applied frequency isunder or over normal range.Normal rangeH : 30 - 70 KHzV : 50 - 120 Hz
English-11TROUBLESHOOTINGCheck if power switch and computer power switchare in the on position.Check if the signal cable is correctly connected tothe video card. Check if the pins of D subconnector are not bent.Check if the computer is in the power- saving mode. Check if power switch is in the on position.Check if the power cord is correctly connected.Check if the signal cable is suitable to the video card.Adjust H &V Size or H&V Position to get the properimage.Keep the devices that may cause electrical interference away from the monitor. See the FCC information at the front cover of themanual.Operate Degauss once.Adjust Contrast and Brightness.Operate Degauss once.Adjust Pincushion/Trapezoid.SymptomNo picture.POWER LED is notlit.Image is unstable.Image is notcentered, too smallor too large.Picture bounces or a wave pattern ispresent in thepicture.Color looks blotchy.Picture is blurred.Edges of availablearea on the screenare not straight.CheckCDT Size 15-inchDiagonal visible image area 14-inchDot Pitch 0.28 mmSynchronization Horizontal 30 - 70 KHzVertical 50 - 120 Hz Plug and Play DDC1/2B/CIPower Saving EPA, VESA DPMS, Nutek CompliantPower Source 100-240 Vac, 50/60Hz (Free Voltage)Power Consumption 80 WDimension-W x H x D 366 x 381 x 400mm(set with stand)Weight-unpacked 27.6/12.5(lbs/Kg)Operating Temperature 10 ~ 40°C /50 ~ 104°FEnglish - 10SPECIFICATIONSFACTORY PRESET TIMINGSMode H.Freq (KHz) V.Freq(Hz) RemarkVGA 640 X 480 31.5 60 Non-interlacedVESA VGA 75 640 X 480 37.5 75 Non-interlacedVGA 720 X 400 31.5 70 Non-interlacedVESA 46K 800 X 600 46.9 75 Non-interlacedVESA SVGA 85 800 X 600 53.7 85 Non-interlacedVESA 60K 1024 X 768 60.0 75 Non-interlacedVESA 1024/85 1024 X 768 68.7 85 Non-interlacedVESA 1280/60 1280 X1024 64.0 60 Non-interlacedResolution(dots Xlines)
S/N : 9978627900DESCRIPTION FOR D-SUB CONNECTORAPPENDIXPin123456789101112131415SignalRedGreenBlueGNDGNDGND-RedGND-GreenGND-Blue+5VdcGND-H.SyncGND-V.SyncBi-directional Data(SDA)Horizontal SyncVertical Sync(VCLK)Data Clock(SCL)161510*GND=Ground

Navigation menu