WOOSIM SYSTEMS PORTI-SWC40 THERMAL PRINTER User Manual

Woosim System Inc. THERMAL PRINTER

User manual

http://www.woosim.com All specifications are subjected to change without notice MODEL PORTI-SWC40 (3inch Mobile Printer) WOOSIM SYSTEMS Inc. Add : #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com
http://www.woosim.com 2 CCooppyyrriigghhtt PORTI-SWC40 portable mobile printer operator’s manual. Copyright 200ⓒ8 by Woosim System Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. and may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies. Caution Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or removed the cable on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer “OFF”. Notice The contents of this manual are subject to change without notice.
http://www.woosim.com 3  Introduction The PORTI-SWC40 is suitable designed for use with a growing variety of mobile devices Bluetooth/Serial interfaces make the PORTI-SWC40 the perfect comrade for applications such as point of transaction warehousing, distribution, point of sales, hospitality, gaming and healthcare. The general features of PORTI-SWC40 printer are as follows: X Pocket size (107.4mm x 88.5mm x 45mm). X Light weight(341g) for true mobility. X Very silent printing thru direct thermal printing method. X High speed (60mm/sec) X High resolution (203dpi, 8dot/mm) X UART (RS-232C or TTL), Bluetooth Ver2.1 + EDR Interface X Intuitive LED’s indicate Power(on/off),Error and Battery status X Smart battery management X Printer door open & Paper-out sensor X Support Magnetic Stripe Reader. X Measure system for thermal print head temperature X Easier paper roll loading by CLAMSHELL design. X Easier maintenance with self-diagnostic. X Microsoft Windows 98/ME/XP/2000/VISTA compatible. X In field programming – Update Firmware, Download Fonts and Logos X Support bit-image(logo) download. X Flow control : Software (XON/XOFF) Hardware flow control not supported in printer.※
http://www.woosim.com 4  Operating Precaution Please follow the precautions below to enjoy and maintain the full performance of the printer. X Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas. Suitable environment for the use of the printer is as follows : Operating temperature◆ :-20°C to 55°C Relative humidity : 0% to ◆95% (No condensation) ● Do not install the printer near devices that generate strong electromagnetic fields such as a copy machine. ● Do not open the platen cover during printing . ● Do not remove or reinstall the communication cable during printing or transmission. ● Do not touch the connectors of the communication cable and to close up the Infrared transmitter /receiver during printing. ● Switch the POWER OFF when not in use. ● Do not use alcohol or other solvent. ● The AC adapter, the battery charger and the battery pack may become warm when in use. This is normal and is not a malfunction. ● When the battery pack is used at low temperature, the length of time the printer can be used may be shortened.
http://www.woosim.com 5 X Thermal Paper Handling ● Store the thermal paper in a cool, dry and dark place. ● Do not rub the paper with hard object. ● Do not leave the paper with hard object. ● Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods. ● Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies. ● Do not use chemical glue. ● Always use the clean thermal paper. .
http://www.woosim.com 6CONTENTS Copyright ............................................................................................................................... Trademark .............................................................................................................................. Caution ......... ..... .... .... .... .... ..... .... .... ...... ..... .... .... .... .... ..... .... .... .... ..... .... ...... .... ..... .... ................ 1. Outline ............................................................................................................................... ...... ...... .. 7 1.1. Model classifications ...................................................................................................... ...... 7 1.2. Product Part Number System ................................................................................................ 7 1.3. Specifications ........................................................................................................................ 8 2. Setting up the printer ............................................................................................................... ...... .. 9 2.1. Printer & Accessories ........................................................................................................... 9 2.2. Printer Features ................................................................................................................. .. 10 2.2.1. Part name ................................................................................................................. 10 2.2.2. Dimensions .............................................................................................................. 11 2.3. Replacing paper roll ............................................................................................................ 12 2.4. Power supply ...................................................................................................................... 13 2.4.1. Internal power supply .............................................................................................. 13 2.4.2. Installing the Battery ................................................................................................ 13 2.4.3. Recharging the battery pack ..................................................................................... 14 2.5. Set operation mode ............................................................................................................. 15 3. Interface ...................................................................................................................... ....... ...... ...... 19 3.1. UART(RS-232C or TTL) ................................................................................................... 19 3.2. Bluetooth ...................................................................................................................... ...... 20 4. Using the printer ................................................................................................................ ...... ...... 21 4.1. Control panel .................................................................................................................... .. 21 4.2. Self test ............................................................................................................................... 22 5. Consumable parts .......................................................................................................................... 23 5.1. Recommended paper ........................................................................................................... 23 5.2. Printing position ................................................................................................................ .. 23 6. Channel organized table ........................................................................................................ ...... .. 24 6.1. Bluetooth channel organized table ...................................................................................... 24
http://www.woosim.com 711.. OOuuttlliinnee 11..11.. MMooddeell ccllaassssiiffiiccaattiioonnss 11..22.. PPrroodduucctt PPaarrtt NNuummbbeerr SSyysstteemm PORTI-SWC40 ( ) ( ) Model Name Interface None : Bluetooth/UART Power None : DC 8.4V Model name / Interface Spec. Example) 1. Porti-S40 UART/Bluetooth Part No. ⇒ S40/A1 2. Porti-SC30 Bluetooth Only Part No. ⇒ SC30/Z1 Note) The above table is the interface format which is supported. But some of the interfaces are not supported according to the product and please contact us, if you have any questions regarding the interface. S40 SC30 W25 . . . Wired Wireless A UART 1 Bluetooth B TTL 2 IrDA C USB 0 None D RS-485 E Parallel Z None
http://www.woosim.com 811..33.. SSppeecciiffiiccaattiioonnss Item Specification Printing method Direct thermal line printing Characters per line 64cpl (9 x 24), 48cpl(12 x 24), 24cpl(24 x 24) Character size Eng. : 9*24dots, 12*24dots Kor. : 16*24dots, [24*24dots] Optional Characters Simplified/Traditional Chinese, Arabic, Cyrillic, Russian, Tukish, Greek, Japanese, Persian, Latin9 and Others upon request. Resolution 203dpi, 8dots/mm Print width 3-inch (72mm, 576dots) Printing speed 60mm /sec Dimensions 107.4 x 88.5 x 46.1mm Weight 341g (Including battery & roll paper) Interface UART(RS-232C or TTL), Bluetooth Ver2.0 Paper supplied Thermal roll paper (80mm wide, 38ø) Barcode supplied 1-dimension : Code128, EAN 128, Code39, I2/5, Code93 UPC, EAN, KAN,JAN, CODABAR 2-dimension : PDF417, QR Code, DATA Matrix Black mark Support black mark detection H/W Spec. MCU : 32bit RISC, FLASH : 4 Mbytes, RAM : 8 Mbytes Receive buffer size 1M bytes Battery Rechargeable 7.4V DC, 1800mAh (Li-ion) Battery duration 1 hour continuous printing Battery Charger Input (100~250VAC, 50~60Hz) Output(8.4VDC/0.8A), 4hours full charge time Environment Conditions Temperature -20°C ~ 55°C Humidity 0% ~ 95% MCBF (Mean Cycle Between failure) Mechanical 37,000,000 lines Head Approximately 50 Km
http://www.woosim.com 922.. SSeettttiinngg uupp tthhee pprriinntteerr 22..11.. PPrriinntteerr && AAcccceessssoorriieess Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. PORTI-SWC40 Battery Pack Roll Paper Battery Charger Communication Cable ▼ OPTIONAL Extra Charger
http://www.woosim.com 1022..22.. PPrriinntteerr FFeeaattuurreess 22..22..11.. PPaarrtt nnaammee
http://www.woosim.com 1122..22..22.. DDiimmeennssiioonnss
http://www.woosim.com 1222..33.. RReeppllaacciinngg ppaappeerr rroollll 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover using finger on both side of printer, and remove the remaining paper. 3. Insert the paper roll as shown. 4. Tear the excess paper off using the edge of paper door as a tear bar. Note : Be sure to use paper rolls that meet the specifications.Do not use paper rolls that have the paper glued to thecore because the printer cannot detect the paper endcorrectly.
http://www.woosim.com 1322..44.. PPoowweerr ssuuppppllyy 22..44..11.. IInntteerrnnaall ppoowweerr ssuuppppllyy The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 22..44..22.. IInnssttaalllliinngg tthhee BBaatttteerryy ① To install battery pack, proceed as follows: - Insert the Battery pack in the direction of the arrow. ② Removing the battery pack - Turn the printer power off and push the battery pack lock and to lift up the direction of the arrow. ③ The battery pack install into extra charger. - Insert the Battery pack in the direction of the arrow. NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer. CAUTION : Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
http://www.woosim.com 1422..44..33.. RReecchhaarrggiinngg tthhee bbaatttteerryy ppaacckk For recharging the battery pack, install the battery pack in the printer or the extra charger. Insert the Battery Charger to the charge connector of the printer or the extra charger. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases. (Warranty 6 month) ● If the printer is not used for a long time, unplug the power cord from the printer and outlet. ● The recharging time depends on the voltage level and ambient temperature of the battery. Normally, if takes about 4 to 5 hours to recharge a battery pack. ● You must use only the supplied adapter. ● Red Lamp : charging the battery. Green Lamp: charging is finished.
http://www.woosim.com 1522..55.. SSeett ooppeerraattiioonn mmooddee 1. Press the MODE Button until the Error Lamp twinkles 5 times. 2. Change the mode and option using the MODE Button according to the MODE z MODE button : use for changing OPTION status. (Error Lamp) z FEED button : use for changing MODE status. (Power Lamp) Ex) The defaults of the printer are : UART/ 9600 bps/ 8 data bit / No parity / 1 Stop bit / Density Low If a user wants to modify the defaults with Bluetooth / 57600 bps / 7 data bit / Odd parity / 2 Stop bit / density high X Press MODE Button until Error Lamp twinkles 5 times and release the button. → You will see the Power Lamp twinkles one time and the Error Lamp twinkles 1 time. → Press the MODE Button 2 time and the Error Lamp twinkles 3 times. (The interface mode has set to Bluetooth mode) X Press FEED button one time, Power Lamp twinkles twice and Error Lamp twinkles 1 time. → Press the MODE Button 3 times and the Error Lamp twinkles 4 times. (The baud rate has set to 57,600 bps) X Press FEED Button one time, Power Lamp twinkles 3 times and Error Lamp twinkles 2 times. → Press MODE Button one time, Error Lamp twinkles one time. (The Data Bit has set to 7 data bit)
http://www.woosim.com 16 X Press FEED Button one time, Power Lamp twinkles 4 times and Error Lamp twinkles 1 time. → Press MODE Button one time, Error Lamp twinkles 1 times. (The Parity bit has set to Odd parity bit) X Press FEED Button one time, Power Lamp twinkles 5 times and Error Lamp twinkles 1 times. → Press MODE Button one time, Error Lamp twinkles 2 times. (The Stop bit has set to 2 Stop bit) X Press FEED Button one time, Power Lamp twinkles 6 times and Error Lamp twinkles 1 time. → Press MODE Button one time, Error Lamp twinkles 2 times after then press MODE Button again, the Error Lamp will twinkle 3 times. ( The density has set to High) If all the mode have set, press the MODE Button and the FEED Button at the same time after then release the buttons at the same time. The printer will print out the mode status which has modified. (Bluetooth / 57600 bps / 7 data bit / Odd parity / 2 Stop bit / density high ) If the status is not correct, please try it again according to the procedure.
http://www.woosim.com 17 POWER Lamp (Green) ERROR Lamp(Red) Option Communication Port 1 1 UART(RS-232C) 2 Protocol UART(RS-232C) 3 Bluetooth 4 Protocol Bluetooth Baud Rate 2 1 9600 bps 2 19200 bps 3 38400 bps 4 57600 bps 5 115200 bps Data Bit 3 1 7 Data bit 2 8 Data bit Parity Bit 4 1 No Parity 2 Odd Parity 3 Even Parity Stop Bit 5 1 1 Stop bit 2 2 Stop bit Density 6 1 Density Low 2 Density Medium 3 Density High Mark 7 1 No use 2 Use Sensor 8 1 Low 2 Medium1 3 Medium2 4 High
http://www.woosim.com 18 POWER Lamp (Green) ERROR Lamp(Red) Option Power Down 9 1 No use 2 1 minute 3 2 minute 4 3 minute 5 4 minute 6 5 minute
http://www.woosim.com 1933.. IInntteerrffaaccee 33..11.. UUAARRTT((RRSS--223322CC oorr TTTTLL)) The PORTI-SWC40 printer has an UART interface and is connected by means of a 4 pin mini USB socket. In the following table, the signals present on the Mini USB socket are listed: * Applicable connector : SUNG KYUNG (CM-720) Pin No. Name Direction Function 1 TxD Output Transmit Data 2 RxD Input Receive Data 3 CTS - - 4 GND - Ground NOTE : ● When data receiving, when it removes the communication cable, it loses a data.
http://www.woosim.com 2033..22.. BBlluueettooootthh Notice If the quantity of data what printed at once is more than 10,000byte on Bluetooth communication, it would cause the buffer to overflow and the data to get damaged. Category Specification Bluetooth Spec. Bluetooth V2.1 / Class2 (10m) Frequency Range 2.4GHz ISM BAND Data Transmission Rate 57600bps Fixed. Data bit 8 Data bit Fixed. Parity bit No parity Fixed. Stop bit 1 Stop bit Fixed. Output Below 3mWMHZ Modulation type/rash way GFSK SYSTEM / PLL
http://www.woosim.com 2144.. UUssiinngg tthhee pprriinntteerr 44..11.. CCoonnttrrooll ppaanneell X Button - FEED : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - MODE : MODE Button is for use to change communication mode. Do not operate the mode button without instructions. X Panel lamp - Power : Printer is ON and ready to receive data. - Error : Indicates a fault condition or a printer error. (i.e : no paper, paper cover opened. etc.) - Battery Power : These lamps(Green) indicated the battery power remaining. The battery gain in quantity and these lamps are on the decrease. If so, you must recharge the battery by using the battery charger.
http://www.woosim.com 2244..22.. SSeellff tteesstt The Self-Test checks whether the printer has any problems. If the printer does not function properly, contact your dealer. For Self-Test, turn on the power while holding down the FEED Button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting. 3) After printing the current printer status, Self-Test will print a pattern using the built-in character set. 4) The Self-Test automatically ends. The printer is ready to receive data as soon as it complete the Self-Test.
http://www.woosim.com 2355.. CCoonnssuummaabbllee ppaarrttss 55..11.. RReeccoommmmeennddeedd ppaappeerr 55..22.. PPrriinnttiinngg ppoossiittiioonn Type : Thermal Paper Paper width : 80mm Paper thickness : 60±5㎛ Outer diameter : Ø38mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core, and the roll paper which has near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed characters may fade. 3. Change of paper color starts from approx. 70 ℃. Pay attention to heat, humidity and sun light. 4. Color of paper may be changed by being scratched by nail or hard metal, etc.
http://www.woosim.com 2466.. CChhaannnneell oorrggaanniizzeedd ttaabbllee 66..11.. BBlluueettooootthh cchhaannnneell oorrggaanniizzeedd ttaabbllee CH MHZ CH MHZ CH MHZ CH MHZ CH MHZ CH MHZ CH MHZ CH MHZ1 2402 11 2412 21 2422 31 2432 41 2442 51 2452 61 2462 71 24722 2403 12 2413 22 2423 32 2433 42 2443 52 2453 62 2463 72 24733 2404 13 2414 23 2424 33 2434 43 2444 53 2454 63 2464 73 24744 2405 14 2415 24 2425 34 2435 44 2445 54 2455 64 2465 74 24755 2406 15 2416 25 2426 35 2436 45 2446 55 2456 65 2466 75 24766 2407 16 2417 26 2427 36 2437 46 2447 56 2457 66 2467 76 24777 2408 17 2418 27 2428 37 2438 47 2448 57 2458 67 2468 77 24788 2409 18 2419 28 2429 38 2439 48 2449 58 2459 68 2469 78 24799 2410 19 2420 29 2430 39 2440 49 2450 59 2460 69 2470 79 248010 2411 20 2421 30 2431 40 2441 50 2451 60 2461 70 2471
http://www.woosim.com 25 FCC ID : QDDPORTI-SWC40 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ㆍReorient or relocate the receiving antenna. ㆍIncrease the separation between the equipment and receiver. ㆍConnect the equipment into an outlet on a circuit different from that to which the receiver is connected. ㆍConsult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void the user's authority to operated the equipment under FCC rules.
http://www.woosim.com 26 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC

Navigation menu