WOOSIM SYSTEMS PORTI-SWC40 THERMAL PRINTER User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1237539
Application ID	j2AXSVULbLnwq7rskDGFGg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	136.6kB (1707494 bits)
Date Submitted	2010-02-04 00:00:00
Date Available	2010-02-04 00:00:00
Creation Date	2010-01-18 13:12:06
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2010-01-27 11:20:16
Document Title	Microsoft Word - Operator Manual SWC40_100118_TRUBLE SHOOTING 삭제 FCC 문구 추가-1.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	C0D320B9ABBDC2

MODEL
PORTI-SWC40
(3inch Mobile Printer)
WOOSIM SYSTEMS Inc.
Add : #501, Daerung Technotown 3th,
448, Gasan-Dong, GeumChun-Ku,
Seoul, Korea
Tel : +82-2-2107-3700
Fax : +82-2-2107-3707
URL: http://www.woosim.com
All specifications are subjected to change without notice
http://www.woosim.com
Copyright
PORTI-SWC40 portable mobile printer operator’s manual.
Copyright ⓒ2008 by Woosim System Inc.
All rights reserved.
The information contained in this manual is the property of Woosim Systems Inc. and
may not be reproduced in whole or in part without the prior written permission of
Woosim Systems Inc.
Trademark
a registered trademark of Woosim Systems Inc.
All other trademark are the properties of their respective companies.
Caution
Some semiconductor devices are easily damaged by static electricity. You should turn
the printer “OFF”, before you connect or removed the cable on the rear side, in order to
guard the printer against the static electricity.
If the printer is damaged by the static electricity, you should turn the printer “OFF”.
Notice
The contents of this manual are subject to change without notice.
http://www.woosim.com
ˆ Introduction
The PORTI-SWC40 is suitable designed for use with a growing variety of mobile
devices Bluetooth/Serial interfaces make the PORTI-SWC40 the perfect comrade for
applications such as point of transaction warehousing, distribution, point of sales,
hospitality, gaming and healthcare.
The general features of PORTI-SWC40 printer are as follows:
X Pocket size (107.4mm x 88.5mm x 45mm).
X Light weight(341g) for true mobility.
X Very silent printing thru direct thermal printing method.
X High speed (60mm/sec)
X High resolution (203dpi, 8dot/mm)
X UART (RS-232C or TTL), Bluetooth Ver2.1 + EDR Interface
X Intuitive LED’s indicate Power(on/off),Error and Battery status
X Smart battery management
X Printer door open & Paper-out sensor
X Support Magnetic Stripe Reader.
X Measure system for thermal print head temperature
X Easier paper roll loading by CLAMSHELL design.
X Easier maintenance with self-diagnostic.
X Microsoft Windows 98/ME/XP/2000/VISTA compatible.
X In field programming – Update Firmware, Download Fonts and Logos
X Support bit-image(logo) download.
X Flow control : Software (XON/XOFF)
※ Hardware flow control not supported in printer.
http://www.woosim.com
ˆ Operating Precaution
Please follow the precautions below to enjoy and maintain the full performance of
the printer.
X Using the Printer
● Be careful not to drop or bump the printer on a hard surface.
● Do not install the printer in direct sunlight or such areas.
Suitable environment for the use of the printer is as follows :
◆ Operating temperature :-20°C to 55°C
◆ Relative humidity : 0% to 95% (No condensation)
● Do not install the printer near devices that generate strong
electromagnetic fields such as a copy machine.
● Do not open the platen cover during printing .
● Do not remove or reinstall the communication cable during printing
or transmission.
● Do not touch the connectors of the communication cable and
to close up the Infrared transmitter /receiver during printing.
● Switch the POWER OFF when not in use.
● Do not use alcohol or other solvent.
● The AC adapter, the battery charger and the battery pack may
become warm when in use. This is normal and is not a malfunction.
● When the battery pack is used at low temperature, the length of time
the printer can be used
may be shortened.
http://www.woosim.com
X Thermal Paper Handling
● Store the thermal paper in a cool, dry and dark place.
● Do not rub the paper with hard object.
● Do not leave the paper with hard object.
● Do not allow plastic film, erasers, or adhesive tape to touch the paper
for long periods.
● Do not stack the thermal paper with diazo copies immediately
after copying or wet-type copies.
● Do not use chemical glue.
● Always use the clean thermal paper.
http://www.woosim.com
CONTENTS
Copyright ...............................................................................................................................
Trademark ..............................................................................................................................
Caution...................................................................................................................................
1. Outline .............................................................................................................................................7
1.1. Model classifications ............................................................................................................7
1.2. Product Part Number System ................................................................................................7
1.3. Specifications ........................................................................................................................8
2. Setting up the printer .......................................................................................................................9
2.1. Printer & Accessories ...........................................................................................................9
2.2. Printer Features ...................................................................................................................10
2.2.1. Part name .................................................................................................................10
2.2.2. Dimensions ..............................................................................................................11
2.3. Replacing paper roll ............................................................................................................12
2.4. Power supply ......................................................................................................................13
2.4.1. Internal power supply ..............................................................................................13
2.4.2. Installing the Battery ................................................................................................13
2.4.3. Recharging the battery pack.....................................................................................14
2.5. Set operation mode .............................................................................................................15
3. Interface .........................................................................................................................................19
3.1. UART(RS-232C or TTL) ...................................................................................................19
3.2. Bluetooth ............................................................................................................................20
4. Using the printer ............................................................................................................................21
4.1. Control panel ......................................................................................................................21
4.2. Self test ...............................................................................................................................22
5. Consumable parts ..........................................................................................................................23
5.1. Recommended paper...........................................................................................................23
5.2. Printing position..................................................................................................................23
6. Channel organized table ................................................................................................................24
6.1. Bluetooth channel organized table ......................................................................................24
http://www.woosim.com
1. Outline
1.1. Model classifications
PORTI-SWC40
) (
Model Name
Interface
None : Bluetooth/UART
Power
None : DC 8.4V
1.2. Product Part Number System
Model name
Interface Spec.
Wired
S40
SC30
W25
Example) 1. Porti-S40
2. Porti-SC30
Wireless
UART
Bluetooth
TTL
IrDA
USB
None
RS-485
Parallel
None
UART/Bluetooth Part No. ⇒ S40/A1
Bluetooth Only Part No.
⇒ SC30/Z1
Note) The above table is the interface format which is supported.
But some of the interfaces are not supported according to the product
and please contact us, if you have any questions regarding the interface.
http://www.woosim.com
1.3. Specifications
Item
Specification
Printing method
Direct thermal line printing
Characters per line
64cpl (9 x 24), 48cpl(12 x 24), 24cpl(24 x 24)
Character size
Eng. : 9*24dots, 12*24dots
Optional Characters
Kor. : 16*24dots, [24*24dots]
Simplified/Traditional Chinese, Arabic, Cyrillic, Russian, Tukish, Greek,
Japanese, Persian, Latin9 and Others upon request.
Resolution
203dpi, 8dots/mm
Print width
3-inch (72mm, 576dots)
Printing speed
60mm /sec
Dimensions
107.4 x 88.5 x 46.1mm
Weight
341g (Including battery & roll paper)
Interface
UART(RS-232C or TTL), Bluetooth Ver2.0
Paper supplied
Thermal roll paper (80mm wide, 38ø)
1-dimension : Code128, EAN 128, Code39, I2/5, Code93 UPC, EAN, KAN,
JAN, CODABAR
Barcode supplied
2-dimension : PDF417, QR Code, DATA Matrix
Black mark
Support black mark detection
H/W Spec.
MCU : 32bit RISC, FLASH : 4 Mbytes, RAM : 8 Mbytes
Receive buffer size
1M bytes
Battery
Rechargeable 7.4V DC, 1800mAh (Li-ion)
Battery duration
1 hour continuous printing
Battery Charger
Environment
Conditions
MCBF (Mean Cycle
Between failure)
Input (100~250VAC, 50~60Hz)
Output(8.4VDC/0.8A), 4hours full charge time
Temperature
Humidity
0% ~ 95%
Mechanical
Head
-20°C ~ 55°C
37,000,000 lines
Approximately 50 Km
http://www.woosim.com
2. Setting up the printer
2.1. Printer & Accessories
Your printer box should include these items. If any items are damaged or missing,
please contact your dealer for assistance.
Battery Pack
Roll Paper
PORTI-SWC40
Battery Charger
▼ OPTIONAL
Extra Charger
Communication Cable
http://www.woosim.com
2.2. Printer Features
2.2.1. Part name
http://www.woosim.com
10
2.2.2. Dimensions
http://www.woosim.com
11
2.3. Replacing paper roll
Note : Be sure to use paper rolls that meet the specifications.
Do not use paper rolls that have the paper glued to the
core because the printer cannot detect the paper end
correctly.
1. Make sure that the printer is not receiving data; otherwise, data may be lost.
2. Open the paper cover using finger on both side of printer, and remove the remaining
paper.
3. Insert the paper roll as shown.
4. Tear the excess paper off using the edge of paper door as a tear bar.
http://www.woosim.com
12
2.4. Power supply
2.4.1. Internal power supply
The following specification is requested for Power supply.
Battery Charger : DC 8.4V/0.8A
Avoid using power supply which its power capacity of power current is extremely high.
2.4.2. Installing the Battery
NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF.
● If the printer is not used for long period of time, remove the battery pack
from the printer.
CAUTION : Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
① To install battery pack, proceed as follows:
- Insert the Battery pack in the direction of the arrow.
② Removing the battery pack
- Turn the printer power off and push the battery pack lock and to lift up the direction of
the arrow.
③ The battery pack install into extra charger.
- Insert the Battery pack in the direction of the arrow.
http://www.woosim.com
13
2.4.3. Recharging the battery pack
For recharging the battery pack, install the battery pack in the printer or the extra charger.
Insert the Battery Charger to the charge connector of the printer or the extra charger.
NOTE : ● While charging the printer, turn off the printer power.
● Do not remove the battery during charging.
● The battery is consumable parts and when purchasing, compared to
the use hour is gradually decreases. (Warranty 6 month)
● If the printer is not used for a long time, unplug the power cord
from the printer and outlet.
● The recharging time depends on the voltage level and ambient
temperature of the battery. Normally, if takes about 4 to 5 hours to
recharge a battery pack.
● You must use only the supplied adapter.
● Red Lamp
: charging the battery.
Green Lamp: charging is finished.
http://www.woosim.com
14
2.5. Set operation mode
1. Press the MODE Button until the Error Lamp twinkles 5 times.
2. Change the mode and option using the MODE Button according to the MODE
z MODE button : use for changing OPTION status. (Error Lamp)
z FEED button : use for changing MODE status.
(Power Lamp)
Ex) The defaults of the printer are : UART/ 9600 bps/ 8 data bit / No parity
/ 1 Stop bit / Density Low
If a user wants to modify the defaults with Bluetooth / 57600 bps / 7 data
bit / Odd parity / 2 Stop bit / density high
X Press MODE Button until Error Lamp twinkles 5 times and release the
button.
→ You will see the Power Lamp twinkles one time and the Error Lamp
twinkles 1 time.
→ Press the MODE Button 2 time and the Error Lamp twinkles 3 times.
(The interface mode has set to Bluetooth mode)
X Press FEED button one time, Power Lamp twinkles twice and Error Lamp
twinkles 1 time.
→ Press the MODE Button 3 times and the Error Lamp twinkles 4 times.
(The baud rate has set to 57,600 bps)
X Press FEED Button one time, Power Lamp twinkles 3 times and Error Lamp
twinkles 2 times.
→ Press MODE Button one time, Error Lamp twinkles one time.
(The Data Bit has set to 7 data bit)
http://www.woosim.com
15
X Press FEED Button one time, Power Lamp twinkles 4 times and Error Lamp
twinkles 1 time.
→ Press MODE Button one time, Error Lamp twinkles 1 times.
(The Parity bit has set to Odd parity bit)
X Press FEED Button one time, Power Lamp twinkles 5 times and Error Lamp
twinkles 1 times.
→ Press MODE Button one time, Error Lamp twinkles 2 times.
(The Stop bit has set to 2 Stop bit)
X Press FEED Button one time, Power Lamp twinkles 6 times and
Error Lamp twinkles 1 time.
→ Press MODE Button one time, Error Lamp twinkles 2 times after then
press MODE Button again, the Error Lamp will twinkle 3 times.
( The density has set to High)
If all the mode have set, press the MODE Button and the FEED Button at the same time
after then release the buttons at the same time.
The printer will print out the mode status which has modified.
(Bluetooth / 57600 bps / 7 data bit / Odd parity / 2 Stop bit / density high )
If the status is not correct, please try it again according to the procedure.
http://www.woosim.com
16
Communication
Port
Baud Rate
Data Bit
Parity Bit
Stop Bit
Density
Mark
Sensor
POWER Lamp
ERROR Lamp
(Green)
(Red)
Option
UART(RS-232C)
Protocol UART(RS-232C)
Bluetooth
Protocol Bluetooth
9600 bps
19200 bps
38400 bps
57600 bps
115200 bps
7 Data bit
8 Data bit
No Parity
Odd Parity
Even Parity
1 Stop bit
2 Stop bit
Density Low
Density Medium
Density High
No use
Use
Low
Medium1
Medium2
High
http://www.woosim.com
17
Power Down
POWER Lamp
ERROR Lamp
(Green)
(Red)
Option
No use
1 minute
2 minute
3 minute
4 minute
5 minute
http://www.woosim.com
18
3. Interface
3.1. UART(RS-232C or TTL)
The PORTI-SWC40 printer has an UART interface and is connected by means of a
4 pin mini USB socket. In the following table, the signals present on the Mini USB
socket are listed:
Pin No.
Name
Direction
Function
TxD
Output
Transmit Data
RxD
Input
Receive Data
CTS
GND
Ground
* Applicable connector : SUNG KYUNG (CM-720)
NOTE :
●
When data receiving, when it removes the communication
cable, it loses a data.
http://www.woosim.com
19
3.2. Bluetooth
Category
Specification
Bluetooth Spec.
Bluetooth V2.1 / Class2 (10m)
Frequency Range
2.4GHz ISM BAND
Data Transmission Rate
57600bps Fixed.
Data bit
8 Data bit Fixed.
Parity bit
No parity Fixed.
Stop bit
1 Stop bit Fixed.
Output
Below 3mWMHZ
Modulation type/rash way
GFSK SYSTEM / PLL
Notice
If the quantity of data what printed at once is more than 10,000byte on Bluetooth
communication, it would cause the buffer to overflow and the data to get damaged.
http://www.woosim.com
20
4. Using the printer
4.1. Control panel
X Button
- FEED :
When the printer is on, paper can be feed manually by pressing and holding the
FEED button for more than one second.
- MODE :
MODE Button is for use to change communication mode.
Do not operate the mode button without instructions.
X Panel lamp
- Power : Printer is ON and ready to receive data.
- Error : Indicates a fault condition or a printer error.
(i.e : no paper, paper cover opened. etc.)
- Battery Power : These lamps(Green) indicated the battery power remaining.
The battery gain in quantity and these lamps are on the decrease.
If so, you must recharge the battery by using the battery charger.
http://www.woosim.com
21
4.2. Self test
The Self-Test checks whether the printer has any problems. If the printer does not
function properly, contact your dealer. For Self-Test, turn on the power while holding
down the FEED Button. The Self-Test checks the following :
1) Make sure paper roll has been installed properly.
2) The Self-Test prints the current printer status, which provides the control
ROM version and the communication method setting.
3) After printing the current printer status, Self-Test will print a pattern using
the built-in character set.
4) The Self-Test automatically ends.
The printer is ready to receive data as soon as it complete the Self-Test.
http://www.woosim.com
22
5. Consumable parts
5.1. Recommended paper
Type
: Thermal Paper
Paper width
: 80mm
Paper thickness
: 60±5㎛
Outer diameter
: Ø38mm or less
Recording side
: Outside of roll
Cautions
1.
Do not paste the paper to the core, and the roll paper which has near end mark printing
on its near end is recommended.
2.
Chemicals or oil may change the color of paper, or printed characters may fade.
3.
Change of paper color starts from approx. 70 ℃.
Pay attention to heat, humidity and sun light.
4.
Color of paper may be changed by being scratched by nail or hard metal, etc.
5.2. Printing position
http://www.woosim.com
23
6. Channel organized table
6.1. Bluetooth channel organized table
CH
MHZ
CH
MHZ
CH
MHZ
CH
MHZ
CH
MHZ
CH
MHZ
CH
MHZ
CH
MHZ
2402
11
2412
21
2422
31
2432
41
2442
51
2452
61
2462
71
2472
2403
12
2413
22
2423
32
2433
42
2443
52
2453
62
2463
72
2473
2404
13
2414
23
2424
33
2434
43
2444
53
2454
63
2464
73
2474
2405
14
2415
24
2425
34
2435
44
2445
54
2455
64
2465
74
2475
2406
15
2416
25
2426
35
2436
45
2446
55
2456
65
2466
75
2476
2407
16
2417
26
2427
36
2437
46
2447
56
2457
66
2467
76
2477
2408
17
2418
27
2428
37
2438
47
2448
57
2458
67
2468
77
2478
2409
18
2419
28
2429
38
2439
48
2449
58
2459
68
2469
78
2479
2410
19
2420
29
2430
39
2440
49
2450
59
2460
69
2470
79
2480
10
2411
20
2421
30
2431
40
2441
50
2451
60
2461
70
2471
http://www.woosim.com
24
FCC ID : QDDPORTI-SWC40
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions; (1)
This device may not cause harmful interference, and (2) this device must accept any interference
received,
including interference that may cause undesired operation.
CAUTION : Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
ㆍReorient or relocate the receiving antenna.
ㆍIncrease the separation between the equipment and receiver.
ㆍConnect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
ㆍConsult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user's authority to
operated the equipment under FCC rules.
http://www.woosim.com
25
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum 20 cm between the
radiator and your body. This transmitter must not be collocated or operating in conjunction with
any other antenna or transmitter unless authorized to do so by the FCC
http://www.woosim.com
26

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : 
Create Date                     : 2010:01:18 13:12:06+09:00
Modify Date                     : 2010:01:27 11:20:16+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2010:01:27 11:20:16+09:00
Format                          : application/pdf
Title                           : Microsoft Word - Operator Manual SWC40_100118_TRUBLE SHOOTING 삭제 FCC 문구 추가-1.docx
Creator                         : 
Document ID                     : uuid:a7f6d2ef-93db-4790-94f6-a0847422ee2a
Instance ID                     : uuid:6ce2753f-c1f6-486c-8ce3-78ea01eb06db
Page Count                      : 26

EXIF Metadata provided by EXIF.tools