WOOSIM SYSTEMS PORTI-WP40 Thermal Printer User Manual Operator Manual Porti WP
Woosim System Inc. Thermal Printer Operator Manual Porti WP
Users Manual
GGGGGGGGGG GG MODEL PORTI-WP40 (PANEL PRINTER) WOOSIM SYSTEMS Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice G Copyright PORTI-WP40 panel printer operator’s manual. Copyright Ꮧ2006 by Woosim System Inc. All rights reserved. The information contained in this manual is the property of Woosim System Inc. And may not be reproduced in whole or in part without the prior written permission of Woosim System Inc࣋ Trademark a registered trademark of Woosim System Inc. All other trademark are the properties of their respective companies. Caution Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or removed the cable on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer “OFF” Notice The contents of this manual are subject to change without notice. ࣞउउࢽऐऍंऀआःआऀࣾऑआऌऋऐࢽࣾएंࢽऐऒࣿइंऀऑंँࢽऑऌࢽऀअࣾऋऄंࢽऔआऑअऌऒऑࢽऋऌऑआऀंࢽ G aVVUUG YWW^TWZTY]G FCC Compliance Statements Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. guarantee that interference will not occur in a particular installation. However, there is no If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio / TV technician for help. Warning : Your are cautioned that any change or modifications to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment. G Introduction The PORTI-WP40 is an extremely simple and functional panel printer. It is the ideal solution for applications which require the immediate printing of data on a paper, whether they be of an industrial, professional or laboratory nature. Medical analyzer, Industrial instrument, Recorder, Geological analyzer, Underground analyzer, Chemical analyzer, Metallic analyzer, etc. G The general features of PORTI-WP40 printer are as follows: X Ultra small size rack mount printer. X Very silent printing thru direct thermal printing method. X High speed(40mm/sec) X RS-232C or TTL interface X Support text and graphic printing. X Support bit-image(logo) download. X Easier paper loading by CLAMSHELL design. X Easier maintenance with self-diagnostics. X Flow control : Software (XON/XOFF) Hardware flow control not supported in printer. G aVVUUG YWW^TWZTY]G G Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. X Using the Printer Ɣ Be careful not to drop or bump the printer on a hard surface. Ɣ Do not install the printer in direct sunlight or such areas. Suitable environment for the use of the printer is as follows : Operating temperature : -10°C to 40 °C Relative humidity Ɣ : 10% to 90% (no condensation) Do not install the printer near devices that generate strong electromagnetic fields such as a copy machine. Ɣ Do not remove or reinstall the communication cable during printing or transmission. G G G aVVUUG YWW^TWZTY]G CONTENTS 1. Outline ............................................................................................................................................6G 1.1. Model classifications .................................................................................................................6G 1.2. Specifications ............................................................................................................................7G 2. Setting up the printer ....................................................................................................................8G 2.1. Printer & Accessories ................................................................................................................8G 2.2. Printer Features..........................................................................................................................9G 2.3. Panel Installation .....................................................................................................................10G 2.4. Replacing paper roll.................................................................................................................11G 2.5. Set operation mode ..................................................................................................................12G 2.6. Specified power supply ...........................................................................................................15G 3. Interface........................................................................................................................................16G 3.1. RS-232C ..................................................................................................................................16G 4. Using the printer ..........................................................................................................................17G 4.1. Control panel ...........................................................................................................................17G 4.2. The self test..............................................................................................................................18G 5. Consumable Parts........................................................................................................................19G 5.1. Recommended paper ...............................................................................................................19G 5.2 Printing position .......................................................................................................................19G G aVVUUG YWW^TWZTY]G XUGvG XUXUGtGG wvy{pˀ~wG G OG G G PG G G OG G G PG G OG G G PG Model name Size of roll paper 40 : 113mm wide, 40 Ø Interface None : RS-232C or TTL Power None : DC 9V G aVVUUG YWW^TWZTY]G XUYUGzG Item Specification Print method Direct thermal line printing Characters per line 92cpl (MAX) Character size Eng. : 9Ý24dots, 12Ý24dots Resolution 203dpi, 8dots/mm Print width 4-inch (104mm, 832dots) Print speed 40mm/sec Dimension 143 Ý 77.7 Ý 46.7 mm Weight 340g (including paper roll) Interface RS-232C or TTL Paper roll Thermal paper roll (113mm wide, 40ø) Kor. : 16Ý24dots, [24Ý24dots] PDF417(2-dimension), Code128, Code39, I2/5, Code93 Barcodes UPC, EAN(KAN, JAN), CODABAR Receive buffer size 10K bytes Printing speed may be slower, depending on the data Note transmission speed and the combination of control commands. Input Power 9VDC, Standby 60mA and Max 3A (Standard model) Temperature Environment conditions -10°C ~ 70°C (storage) 30% - 80% (operating) Humidity 10% - 90% (storage) MCBF (Mean Cycle Between failure) -10°C ~ 40°C (operating) Mechanical Head 37,000,000 lines Approximately 50 Km G aVVUUG YWW^TWZTY]G YUGzGGGG YUXUGwGMGhG G Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Roll paper Porti-WP40 G aVVUUG YWW^TWZTY]G YUYUGwGmG G aVVUUG YWW^TWZTY]G YUZUGwGpG G aVVUUG YWW^TWZTY]G XW YU[UGyGGG Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper roll cover using your finger on both side of printer and remove the remaining paper. 3. Insert a new paper roll as shown. 4. Tear the excess paper off using the edge of paper door as a tear bar. G aVVUUG YWW^TWZTY]G XX YU\UGzGGG 1. Press the Mode Button until the Error Lamp twinkles 5 times 2. Change the mode and option using the Mode Button and the Feed Button according to the MODE code(Table1) z Feed button : use for changing MODE status z Mode button : use for changing OPTION status [Example] The defaults of the printer are:RS-232C/9600 BPS/8 DATA BIT/NO PARITY/ DENSITY LOW If a user wants to modify the defaults with RS-232C / 38400 BPS/7 DATA BIT/ EVEN PARITY / DENSITY HIGH Press the Mode Button until the Error Lamp twinkles 5 times and release the button. o You will see the Power Lamp twinkles one time and the Error Lamp twinkles 1 time. o This mode is RS-232C mode. Press the Feed button one time, the Power Lamp twinkles twice and the Error Lamp winkles 4 times. o Press the Mode Button one time, the Error Lamp twinkles 5 times and press the Mode Button one more time, the Error Lamp twinkles 6 times. (The baud rate has set to 38,400 bps) Press the Feed Button one time, the Power Lamp twinkles 3 times and the Error Lamp twinkles 2 times. o Press the Mode Button one time, the Error Lamp twinkles one time. (The Data Bit has set to 7 data bit.) Press the Feed Button one time, the Power Lamp twinkles 4 times and the Error Lamp twinkles 1 time. G G G aVVUUG YWW^TWZTY]G XY G o Press the Mode Button one time, the Error Lamp twinkles 2 times. (The Parity bit has set to even parity bit.) Press the Feed Button one time, the Power Lamp twinkles 5 times and the Error Lamp twinkles 1 time. o Press the Mode Button one time, the Error Lamp twinkles 2 times after then press the Mode Button again, the Error Lamp will twinkle 3 times (The density has set to High) If all mode have set, press the Mode Button and the Feed button at the same time after then release the G buttons at the same time. The printer will print out the mode status which has modified. (RS-232C/ 38,400 BPS/ 7 DATA BIT/ EVEN PARITY/ DENSITY HIGH) If the status is not correct, please try it again according to the procedure. G G G aVVUUG YWW^TWZTY]G XZ G G MODE LED OPTION RS-232C 1200BPS 2400BPS 4800BPS 9600BPS 19200BPS 38400BPS 57600BPS 115200BPS 7 DATA BIT 8 DATA BIT NO PARITY EVEN PARITY ODD PARITY DENSITY LOW DENSITY MEDIUM DENSITY HIGH Not Used Not Used
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2007:03:26 11:40:35+09:00 Modify Date : 2007:04:06 09:43:21+09:00 Metadata Date : 2007:04:06 09:43:21+09:00 Document ID : uuid:8998484A43DBDB11BCBBDE64690DF843 Instance ID : uuid:e091261a-3ce9-4f83-a0eb-7f95366d0417 Derived From Instance ID : uuid:27a659fc-9c88-40e8-a52e-dbc78e8eac54 Derived From Document ID : uuid:1b8bac08-497b-4261-9a09-4f51e6e292ec Format : application/pdf Title : Microsoft Word - Operator Manual Porti_WP.doc Creator :EXIF Metadata provided by EXIF.toolsPage Count : 20 Author :