Wacom Co DTF521 LCD TABLET User Manual DTF 521 EN indd

Wacom Co Ltd LCD TABLET DTF 521 EN indd

USERS MANUAL

 1    So that the DTF-521 may be Used Safely...■Regarding the power plug and power adapter. -Please remove dust from the power plug regularly. The addition of moisture, etc.  to  accumulated  dust  may  lead  to fire. -Please do not use any power adapters other  than  those  included  with  the product. Ignoring this warning may result in fire or product failure. -Please do not damage or forcibly bend or bundle the power adapter cord. Also, please  do not  place  heavy objects on  it or expose it  to excessive heat.  Ignoring  this  warning  may  result in fire, electric shock or product failure.  -In the unlikely case that the power adapter should produce smoke  or a strange odor, please disconnect it from the wall outlet and return it to either the store where you purchased it or to the Wacom  Customer  Support  Center  for repair service. -Please  do  not  connect or  disconnect the power adapter with wet hands. Ignoring this warning may result in electric shock or malfunction. -Please do not open or otherwise change the power adapter. Ignoring this warning may result in fire or electric shock.In order to  prevent this, when in such locations, always disconnect the productʼs USB connector from your computer and turn off the switch. ■Do not open the back cover. Inside this product there are several high-voltage parts.  Persons other than professional service personnel should never open the back cover of this product. Unauthorized opening of the back  cover  may  lead  to  fire  or  electric shock. ■When  this  product  ceases  to  operate normally due to being dropped or a similar  cause,  remove  the power source cable from the electrical outlet. Leaving the power cable connected may result in fire or electric shock.  This  product may  cause other  electronic devices  to malfunction,  or  other  devices may cause this product to malfunction.■Turn  this  product  off  in  places  where the use of electronic equipment is prohibited. In airports,  hospital intensive  care  units and other such places where the use of electronic equipment is prohibited, this product may adversely affect the operation of other electrical devices. The following symbols appear throughout this user guide in order to ensure safe use of the DTF-521 (hereafter referred to as “DTF-521,” “the product” or “this product”). Please read these items carefully and always heed the Warning and Caution items when using your DTF-521.This symbol indicates an item that, if ignored when handling the product, could lead to the loss of life or serious injury.WarningThis symbol indicates an item that, if  ignored when  handling the  product, could lead to injury or damage to personal property. CautionMeanings of Symbols:Indicates that it is important to be careful when taking the action or actions noted.Indicates that the action or actions noted are to be avoided.Indicates it is important to take the action or actions noted.Warning■Do  not  use  the  product  in  a  facility c o n t r o l  s y s t e m  t h a t  r e q u i r e s  a n extremely high level of reliability. User's Guide
 2  of time, disconnect the power adapter from the electrical outlet.■Do not use this product in a dusty environment. Dust can cause damage to the product.  ■Do not block the ventilation holes  on the backside of the product.Blocking  these  holes  may cause  internal overheating and subsequent damage. ■Do not pick up the product by its stand.If excessive  force is used  in handling the stand, its open and close function may become damaged. When picking  up  the product, always pick it up by the body. ■When connecting the power plugWhen plugging the power  adapter  into an electrical  outlet,  also connect  a  grounded wire. ■When not using this product for a long period of time For  safety reasons,  when  you  will not  be using the product for a considerable length ■Do  not  use  organic  solvents  to  clean this product. When cleaning  the product, never use such  organic  solvents  as  alcohol.  Such solvents may cause  discoloration  and deterioration in quality.■When cleaning this product, always disconnect the USB connector. When cleaning the product, always disconnect the USB  connector from the USB port of the computer. Failure to do so may result in electric shock. ■While this product is in use, avoid placing any metal objects on it. Do  not  place  any  metal  objects  on  the product while  you  are using it. This  may result in malfunction or product failure. ■Do not touch any  liquids that may be leaking from this product. The liquid contained in  the  product  is  an irritant. In the unlikely case that such liquid should leak, never touch it with bare hands. In case of contact with skin, mouth or eyes, rinse immediately  with running  water and continue  rinsing  for  15 minutes  or longer. Also consult a physician.  ■Do not use excessive force with the cable. Please do not step on, or place heavy objects on any of the productʼs cables. Also,  do  not  apply  excessive  force  to  the base  of the  cable  or  repeatedly bend  and stretch it, as  this  may cause it to break  or malfunction.■Do not place the product in either very hot or very cold places.Do not  place the  product  in very  hot (35 degrees centigrade or more) or very cold (5  degrees centigrade  or  less) locations. Also, avoid placing it in locations with severe temperature fluctuations as  this may adversely affect the product and cause product failure.■Do not disassemble the product.Do not disassemble or modify the product, as these actions may lead to fire, excessive generation of heat, electrical shock or injury. The guarantee on the product will  become  null  and  void  if  the product is ever disassembled. CautionSo that the DTF-521 may be Used Safely■Do not let the product get wet. Please do not place containers such as cups and vases containing water near the product. Coming in contact  with water  or other  liquids may cause product failure.■Regarding the Grip Pen-Do not strike hard objects with  the metal  Grip  Pen. Doing  so  may  cause damage to the product. -Be careful to not allow  small  children to  put either  the  pen or  the  spare nib into their mouths. There is the danger that  the  nib  or  side  switch  may  be accidentally swallowed or that the grip pen may be damaged. ■Do not place the product on unstable surfaces. Do  not  place  the  product  where  it  is likely to totter, lean or be exposed to strong vibrations. Doing so may lead to the product falling, resulting in injury and/or product failure. ■Do not place heavy objects on the product. Do not put excessive weight, or place heavy  objects  on  the  product.  These actions may cause product failure.
 3 Caution■Do  not  connect  or  disconnect  any  cable while  the  product or  your computer is on. Do  not connect  or  disconnect  any cable  (including  the  USB cable)  or  the  power adapter while your computer or this product is turned on. This may cause damage to the product or to your computer.
 4  1 Wacom Company, Ltd. holds the copyright to the auxiliary tablet. 2  The  unauthorized  duplication or  reproduction in  whole  or in part  of  the  tablet  driver  or this user guide is expressly prohibited. 3 Wacom reserves the right to change the configurations or  specifications of the  tablet driver or  the product, as  well as the  contents of this user guide, without prior notice.   As  a  participant  in the  Energy  Star program, Wacom has determined that this product meets the standards of the Energy Star program.Please take the following precautions to protect the health of your eyes. ●When  using  the product,  make  sure  that  the room is  sufficiently illuminated  and be careful not to get your face too close to the screen. ●Take  regular  breaks  when  using  the  product over an extended period of time. Warranty ExclusionsRegarding warranty of the productWacom  warrants  the  product,  to  the  original consumer purchaser, except software, to be free from defects in materials and workmanship  under normal  use  and service as long as the product remains in production, but not less than  one (1) year, from  the date of  original  retail  purchase,  as  evidenced  by  a copy of the receipt or a registration card that has  been  returned  to  Wacom  within  30  days of purchase.Regarding Trademarks●Wacom are registered trademarks of WACOM Company, Limited.●Windows is a trademark of Microsoft Corporation,  registered  in  the  United  States and other countries. ●Macintosh is a trademark of Apple Computer, Inc., registered in the United States. ●Other product names and  related  items  are the  trademarks or registered trademarks  of each concerned company.  Precautions  Depending on what is being displayed, bright or dark green, red and blue dots may show up on a very small portion of the LCD display screen. These do  not indicate product failure or a  lack of quality. So that the DTF-521 may be Used Safely●Wacom  will  not  bear any responsibility  for damage caused by fire, earthquake, accidents caused by third persons, intentional or accidental abuse by the customer or any other damage caused by abnormal use of the product. ●Wacom  will  not  bear any responsibility  for contingent damages (such as loss of business profits,  suspension  of  operations,  alterations to and disappearance of data, etc.) caused by use of, or inability to use, this product.●Wacom  will  not  bear any responsibility  for damage resulting from the use of this product in a fashion  other than as explained in this user guide. ●Wacom  will  not  bear any responsibility  for damage resulting  from malfunctions  caused by using this product in conjunction with adaptation equipment or other company’s software.Regarding this User Guide  This user guide contains instructions  regarding the set  up, installation,  functions and methods of use of this product. The product consists of the  LCD monitor  and the  tablet, which  will  act as two distinct pieces of equipment to be used in  conjunction  with  your  computer.  First,  you will set up the display device and then you will install the  tablet driver in  your computer. You will then be able to use this product as a built-in display tablet.   Analog RGB compatible video output is necessary for the screen display of this product. For  information  regarding  how  to  use video cards, refer to the instruction manual accompanying the video card. Please be aware of the following regarding the LCD display.
 5   Table of ContentsSo that the DTF-521 may be Used Safely... ..............1Table of Contents ....................................................5Component Functions ..............................................6Opening the Stand .......................................................................... 7Using the Penholder ........................................................................ 7Installing DTF-521 on a Mount Arm ................................................... 8Accessory Check .....................................................9Connecting DTF-521   ...............................................10Installing DTF-521 Driver .........................................12Windows Setup .............................................................................. 12Macintosh Setup ............................................................................. 13Uninstalling the Tablet Driver ............................................................ 13Switching Display Images ................................................................ 14The Auto-Adjust Function .................................................................. 14The DTF-521 Power Saving Function ................................................. 14The DTF-521 Display ...............................................14Protrusion of the Picture from the LCD Panel and the Blurring of Characters... ..... 15Button Functions .............................................................................. 16Adjusting the Brightness and Contrast of the Display ........................... 16Pen .........................................................................19Basic Operations of the Pen ............................................................. 20How to use the Tablet Button ............................................................ 21Using the Control Panel ...........................................22Displaying the Control Panel ............................................................ 22Control Panel Basics ........................................................................ 22Synchronizing the Positions of the Pen Tip and Pointer ......................... 23Setup Procedures for  when Multiple Interactive  Pen Tablets are Connected .............................................24Supplementary Information     .................................25Removing Stains ............................................................................. 25Replacing the Pen Nib ..................................................................... 25Troubleshooting ......................................................26Display Troubleshooting ................................................................... 26The Pen and Side Switch do not Operate Correctly (For Both  Windows and Macintosh) ..................................................................................... 28General Troubleshooting .................................................................. 28Troubleshooting for Windows ........................................................... 29Troubleshooting for Macintosh .......................................................... 29Obtaining Technical Support    .................................31
 6     Component FunctionsIntegrated LCD Monitor and Tablet+ Button- ButtonENTER ButtonMenu ButtonStand Adjustment Lever▶P.7▶P.16Connector▶P.11Stand▶P.7TopPower SwitchPen RestPlace the pen here while the pen is not in use.Power LEDLights blue  when  power  has been supplied the DTF-521 and the computer and video signals is present. Glows orange when no video signal is detected by the DTF-521. Status LEDWhen the pen switch is on, this will become blue. FrontBackFor Application Software buttonsEnable  y o u  t o  c re a t e  d i ffe rent funct i o n s  f o r supporting application softwareTablet ButtonYou can operate a zoom function and a scroll function with a single touch of a button.
 7   Opening the Stand1Pull up on the stand adjustment lever. 2Let the stand down.  Using the PenholderPull the penholder towards you as shown in the illustration below.  12Caution  Always close the stand and, as shown in the above illustration, lay the tablet on its side before pulling the penholder out.
 8    Installing DTF-521 on a Mount ArmCaution  When installing the unit on a mount arm or other stand, always follow the directions in the instruction booklet for the mount arm or stand, as well as the instructions contained in this document. Incorrect installation may result in the product coming loose and falling and possibly causing product failure. 5Connect the cables and save the screws that you removed in step 3. 3Remove the four screws that hold the stand to the unit.  4Using four M4/0.7mm screws, securely mount the arm or similar apparatus to the back of  the unit.2Place the display unit face down on a flat surface. To prevent harm to the front of  the unit, first spread a cloth or other similar material on the flat surface.UnscrewComponent FunctionsThis product conforms to the Video Electronics Standard Association’s (VESA) Flat Panel Monitor Physical Mounting Interface Standard (FPMPMI). This product can be removed from the stand and mounted on such apparatuses as a VESA-standard mount arm. In order to do this, M4/0.7 mm screws, which are not included with the product, are needed. Use screws that will, at the time of  installation, penetrate the surface of  the product by no more than 15 mm. Use of  longer screws may result in damage to internal parts of  the product. 1Make sure that both your computer and the product are turned off  and that all cables are disconnected.
 9 ●USB Cable●Power Adapter●Power Cable●Pen●User Guide (This booklet)●Serial CableUser Guide ●Tablet Driver CD - ROM /       Application CD - ROM   Accessory Check    Important  Do no  throw the  box away; it is useful  for the storage and transport  of the product.●Application Install Guide Application Install Guide
 10  1Turn off  both your computer and the product.2Connect the Analog-RGB connector to your computer’s display port. 3Connect the power adapter to the power cable and connect the DC power connector to the DC power  input terminal. Next, plug the power cable into your electrical outlet. Be sure to also connect a ground wire.4Turn on the product’s power switch. The power indicator lamp will light up orange. 5Turn on your computer. 6While looking at the LCD screen, configure the color resolution and size settings.7Turn off  your computer and the product.8Connect a USB connector of  the product to a USB port of your computer using a USB cable.9Turn on your computer and the product. 10Install the DTF-521 driver (Please refer to “Installing DTF-521 Driver” on page 12).- Do not modify the refresh rate. Setting the rate to a value that exceeds the DTF-521 refresh rate may result in loss of picture. - The color palette settings and corresponding number of colors displayed are as follows: High Color (16 bit) →65,536 colors / True Color (24 bit) → Roughly 1,619 colors*The number of colors is limited by the efficiency of your computer and video card. For details, refer to the user’s manual provided by the manufacturers.    Important   Connecting DTF-521
 11 USB connectorConnectors AreaUSB cablePower cablePower AdapterDC Power Input TerminalTo analog RGB portTo USB portDTI-520UB Rear ViewComputerOutletGround WireTo monitor or projector(Output )(Input)Analog RGB connectorAnalog RGB cableAnalog RGB connectorComputer238
 12    Installing the Tablet Driver  Windows SetupBefore installation, connect the DTF-521 USB cable to your computer and turn the unit on.   Installing DTF-521 Driver     Hint  Users utilizing a serial cable connection may find that the ADD NEW HARDWARE WIZARD dialog box displays. Click CANCEL and continue the installation process.1First turn on the DTF-521. Then turn your computer on and login, allowing the operating system to  fully load. The DTF-521 will automatically register as a USB device.   Windows 98SE: The ADD NEW HARDWARE WIZARD will display. Follow the prompts, se-lecting the default options. If prompted to install drivers for the USB Human Interface De-vice, insert the Windows 98SE CD, click OK, and enter the location of  the Windows CAB files (e.g., D:\WIN98). Note that the files may be located on your hard disk in the C:\WINDOWS\OP-TIONS\CABS folder.2Insert the DTF-521 tablet driver CD into the CD-ROM drive. The DTF-521 menu should automatically display. If  the menu does not display, double-click on the INSTALL icon (lo-cated on the CD). Click on the INSTALL PEN TABLET button and follow the prompts  to install the driver software.  Installing the Button DriverYou can use the tablet button, if  you install the Button Driver.1You click NEXT in the WELCOME TO WACOM BUTTON DRIVER VER.x.xx SETUP dialog.2LICENSE AGREEMENT dialog is displayed. You click YES.3CHOOSE DESTINATION LOCATION dialog is displayed.  You click YES and click YES in the next dialog again.4Follow the prompts to install the driver software.5INSTALLWIZARD COMPLETE dialog is displayed. Click FINISH.6You select YES, I WANT TO RESTSRT MY COMPUTER or NO, I WILL RESTSRT MY COM PUTOR.7See "How to use the Tablet Button( ▶Page.21)" about the Tablet button.     Hint  The latest information about the DTF-521 driver is described in the technical note.  Please read it certainly after the driver is installed.
 13   Macintosh Setup1 Connect the USB cable to your computer, turn on the product and start up your Macintosh. 2 Close any open applications and temporarily turn off  any virus-monitoring programs.  3 Insert the Tablet Driver CD-ROM into your computer’s CD-ROM drive. The install menu will appear. If it doesn’t appear, open the CD-ROM and double-click on Install or Install.app.4 Click on Install Wacom Tablet and installation will begin.  Thereafter, follow the screen instructions and continue the installation process.    If  during processing, the identity confirmation dialog box displays, input your password *.  Uninstalling the Tablet Driver     Hint*After installing OS X, input your password.   Macintosh OS x 10.2 and newer versions include as a standard feature the Inkwell function. If this function is on, the yellow Inkwell memo pad will appear after installation of the Tablet Driver. To disable this function, click on Ink from the Control Panel, click on Settings and remove the checkmark from Allow Me to Write Anywhere.  5 After the tablet driver installation is complete, restart Macintosh.      Caution  Windows1Click on the Windows Start button and open the control panel. Double click the Add and Delete Pro-gram (Application) icon. 2 Select Pen Tablet from the list and click the Modify (Add) and Delete button. Follow the instructions in the dialog box to initiate uninstall. If Windows is restarted, it is deleted.  Macintosh1 Open the Applications folder and then open the Tablet folder. 2 Start up Remove Tablet and follow the instructions to initiate uninstall.
 14     The DTF-521 Display * Depending on the specifications and settings of your computer and video  card, when in standby and suspend modes, the power lamp may only light  up orange.This  product  is  in compliance  with  VESA and  ENERGY  STAR power-saving  guidelines. When connected to a Display Power Management (DPMS)-compatible computer and graphics board, the power savings indicated below are automatically realized during times of non-operation.Computer ActivityHorizontal Synchronizing SignalVertical Synchronizing SignalPicture SignalPower ConsumptionPower LampTurned On Yes Yes Yes 23W or less BlueStand-by Mode No Yes No Less than 2W  Orange/Blue*Suspend Mode Yes No No Less than 2W  Orange/Blue*Off Mode No No No Less than 1W  Orange The DTF-521 Power Saving Function    ImportantIn order  to ensure optimal display  image  quality,  this product utilizes the Auto-Adjust function. When  the  Auto-Adjust  function  is operating, it  may  take a short  time  before  the  screen  displays properly. The settings initiated by Auto-Adjust are saved in the display.  If  the Auto-Adjust function  is operating, the  horizontal and vertical  positions as well as the phase  and pitch of the display are adjusted automatically  when the display mode  is received. The  Auto-Adjust function  becomes operational when the horizontal frequency is in the 30-56.5KHz and the vertical frequency is in the 45-75Hz range.(When resolution is 1024 × 768 dot (XGA), vertical frequency is in the 45-70Hz range)  When the Auto-Adjust function is operating, only the power switch is operational.   The Auto-Adjust Function    Hint     Caution
 15 3Using the OSD contorls, open the OSD Menu and the Pitch icon.4Adjusut the pitch level so the pat-tern of  fine vertical stripes display evently.5In the OSD  Menu,  select the Phase icon.6Adjust the phase level so the adju-sutment pattern shows clearly.7After completing these adjust-ments, press  the ENTER and MENU buttons to exit the OSD Menu.8Click on the CANCEL button or press the ENTER and MENU buttons to exit the OSD Menu. Adjustment pattern for pitch and phase  Protrusion of the Picture from the LCD Panel and the Blurring of Characters...Depending on the type of  computer and graphics board, the Auto-Adjust function is sometimes not able to operate at full power, resulting in the picture blurring and protruding from the LCD panel. If  this happens, adjust the pitch and phase. At 1024 x 768-bit, the resolution is optimally adjusted. Procedure:1Open the Tablet Control Panel (see page 22) and select the Calibrate tab. 2Click on the Calibrate... button. An adjustment pattern for pitch and phase will appear.12  This setting is effective when the product and computer are connected by a RGB cable.    Hint  For Windows 2000,  the  pitch and  phase  may  be calibrated  after  the Exit Windows screen  is displayed.  If the  frequency  needs to  be calibrated,  light and  dark  vertical  stripes  will  appear in  the  dark  areas  of  the  screen.  If  the tracking needs to be calibrated, light and shade will appear horizontally in the dark areas of the screen (for 1024 x 768-bit resolution).   This  method  is  recommended  in  situations  where  the  tablet  driver  has  not been installed.      Caution
 16    Adjusting the Brightness and Contrast of the Display How to Use the OSD MenuExample: Adjusting the brightness1Click on the Menu button to display the Main Menu Settings screen.2Click on the + button and the  button and select the items to be adjusted. When the option you want to adjust is highlighted, press the ENTER button. 3Use the + and - buttons to adjust numerical values and other items. 4After making your change, press the ENTER button to save.5To exit, press the Menu button. buttons, + buttons:You can select an option that can be activated.After activatng a selected option, press the + button to increase a selected item value, and press the - button to decrease it.Menu button:Opens or closes the OSD Menu.ENTER ButtonActivates or deactivates the selected OSD menu otion.Also switches the image input from the RGB – RGB cable and the image input from the composite video cable. ▶P.14  Button FunctionsAdjusting picture quality and setting up the display are accomplished by using on-screen buttons to establish and change adjustment items and values. Click on the Menu button and the menu screen appears. Select the items to be adjusted and their desired settings. The DTF-521 Display
 17  Menu Position ResetBrightnessContrastSelect to increase or decrease image contrast.  Types of OSD MenusSelect to increase or decrease image brightness.Select to move the OSD menu around the display.Provides two options:Use AUTO ADJUST to reset only the image parameters. Use RECALL to reset all screen options to the factory default. Selecting the exit ' 'icon exits the RESEST window without resetting anything.Color Backlight LanguageProvides settings for 9300°, 6500°, and 5000°Kelvin.Also provides a User option that enables you to adjust red, blue and green independently.  Selecting DIRECT displays the received signal as it is without any adjustment. Choose a setting to work with and press Enter to activate your selection. You can change the user setting by selecting the icon ' '.In the User Adjustment window, change red, blue  and green to calibrate color.To exit, select the icon ' '.Selects to increase or decrease the backlight brightness level.Select to choose a language option for the OSD: English, Deutsch, Francais, Espanol, Italiano, or Japanese.Some menu  screen displays  may  vary depending  on  whether a RGB  cable  or  a  video cable  is connected. The following screens explained in Common Screens below are the same ones regardless of  the connection method.●Common Screens
 18   Vertical Center Horizontal CenterPitchPhaseSelect to reduc e  or eliminate horizontal distortion lines. ▶ P.18 To automatically ad-just,  use  the  RESET option.Select to reduce or eliminate vertical distortion lines. ▶ P.18 To automatically adjust, use the Reset option.Select to move the screen image left or right.To automatically adjust, use the Reset option.Select to move the screen image up or down.To automatically adjust, use the Reset option.●Screens that Display with a RGB Cable ConnectionThe DTF-521 Display
 19   Gripping the PenYou can hold it just like a pen.   Pen The Parts of the Pen and Their FunctionsPen Tip• You can change the position of the screen pointer by moving the tip of the pen.• By varying the amount of pressure applied, the boldness of lines and the size of points can be adjusted. • If the pen nib shows signs of ware, it can be replaced. See page 25. EraserIt works like the eraser on a pencil.
 20   Moving the Pointer By raising the pen a little above the screen and moving it, you can move the position of  the screen pointer.    Basic Operations of the Pen  Clicking and Double-clickingClickingTap  on  the  screen  lightly  once  with  the  tip of   the  pen  to click.Double-clickingTap in the same place twice quickly with the tip of  the pen to double-click.  DraggingSelect an icon or  folder and  then, while  keeping the  pen tip pushed down, move the pen to move the object.  Using the EraserBy setting the eraser function and then tracing  over  the display, pictures and handwritten characters disappear as if  erased by a standard eraser.
 21 The tablet buttons are connecte the efficiency of  your work.  How to use the Tablet Button   Note  The  tablet  buttons  can be  used  in  Windows-based  PCs.  To  use  the tablet buttons, you have to install the button driver to your PC.( ▶P12)Component Functions1 2345 5No Function Description1 The left mouse button It works like the left mouse button.2 The right mouse button It works like the right mouse button.3 Scroll button (Top) It scrolls the display of a monitor  to upper side.4 Scroll button (Bottom) It scrolls the display of a monitor  to lower side.5 Ctrl button A role of a ctrl button
 22     Using the Control PanelChange the settings for the pen and adjust the pointer and pen tip positions with the control panel. *When connecting and using multiple tablets, see page 24.   Displaying the Control Panel   Opening the Control Panel in WindowsClick on the Windows Start button, go to All Programs (P) or Programs (P), open Wacom Tablet and select Wacom Tablet Properties.   Opening the Control Panel in Macintosh Open System Settings and then Wacom Tablet.NO Setting Item Description1Tip Feel Customizes the amount of pressure needed to click or draw with the pen.2Double Click Distace Adjusts the size of the double-click area.See page 20.3Click Sound When checked, an audible “click” sound will be heard whenever a pen click occurs and your computer speakers are turned on.4Default Returns the PEN tab settings to their factory defaults.5Eraser It works like a eraser.5124  Control Panel BasicsYou select the pen tab.3
 23  Synchronizing the Positions of the Pen Tip and PointerMake  the necessary adjustments so  that when  the pen  nib is  brought near  the LCD  screen, the pointer displays properly in the area where the pen nib is placed (parallactic adjusting).* When using an analog RGB input type of LCD pen tablet, please refer to “Protrusion of the Screen from the LCD Panel and the Blurring of Characters” on page 15 and make any necessary adjustments to the screen. * When using multiple tablets, see page 24. 1 Click on Calibrate... and the screen used for making adjustments will appear.2 Click in the middle of  the cross mark in the upper left-hand corner of  the screen while sitting in your normal seating position with the pen nib and the cross mark will move to the bottom right-hand side of  the screen. 3Click again in the middle of  the cross mark that is now in the bottom right-hand corner of  the screen while sitting in your normal seating position and the cross mark will disappear. The process of synchronizing positions is now complete. Click on the OK button in the lower part of the screen to close the screen.
 24   󰰘󰰪󰰹󰰺󰰵󰯥󰰕󰰷󰰴󰰨󰰪󰰩󰰺󰰷󰰪󰰸󰯥󰰫󰰴󰰷󰯥󰰼󰰭󰰪󰰳󰯥󰰒󰰺󰰱󰰹󰰮󰰵󰰱󰰪󰯥󰰎󰰳󰰹󰰪󰰷󰰦󰰨󰰹󰰮󰰻󰰪󰯥󰰕󰰪󰰳󰯥󰰙󰰦󰰧󰰱󰰪󰰹󰰸󰯥󰰦󰰷󰰪󰯥󰰈󰰴󰰳󰰳󰰪󰰨󰰹󰰪󰰩When multiple interactive pen tablets are connected and are to be used, it is necessary to set up the pen and calibrate for each interactive pen tablet individually. Please follow the procedures below to carry this out.1Bring the pen tip near the display of  the tablet for which the setup is to take place. Verify that the pointer moves in conjunction with the pen tip.2Open the control panel. (Please refer to the screen picture accompanying Step 1 of  the procedure de-scribed in “Protrusion of  the Picture from the LCD Panel and the Blurring of  Characters...” on page 15.)3Open the Calibrate tab and verify that the correct monitor name is displayed in the Monitor field.●If Another Monitor Name is Displayed in the Monitor Field...  The control panel of  a different interactive pen tablet is being displayed. Press the ESC key on    the keyboard to delete the control panel and, beginning with Step 1, repeat the above procedure    to display the correct control panel.*If the monitor name is changed without displaying the control panel, the tablet will not be able to be set up. 【Important】 When  more  than  one interactive  pen  tablet  is connected,  the  control panel  of  the last  tablet  to    recognize  the pen tip is displayed.  Even after identifying the pointer, if you use the  pen on    another  tablet to open  its control  panel, the  pen  tip is  recognized and  the control  panel of  this    tablet opens. Please refer to the following example.  Example > Setting up Tablet A when Tablet A and Tablet B are connected.  1. The pointer is identified by Tablet A.  2. The control panel of Tablet A is displayed. →OK    The pen is used on Tablet B to display the control panel →NOT OK (This carries out the      setup of Tablet B)    The computer mouse is used on Tablet B to display the control panel →OK4Refer to Protrusion of the Picture from the LCD Panel and the Blurring of Characters... on page 15 and carry out calibrations. To set up the pen, open the PEN tab, refer to “Switch and Button Settings” on page 22 and carry out the setup.5Repeat Steps 1 ‒ 4 to set up another tablet.
 25 Remove the pen nib Insert a new nib Please prevent children from placing the grip pen or pen nib in their mouths. There is the danger that the nib may be pulled out and swallowed. If the grip pen is placed in the mouth, it may be damaged.    Supplementary Information  Using a pair of  tweezers or a similar tool, pull the nib out of  the pen.Insert the new nib, firmly pushing it in until it stops.   Removing StainsIf the product casing or pen becomes soiled, wipe off  with a clean, soft cloth. If   this  fails  to  remove  the  stains, soak  a  clean,  soft cloth  with  a  water-diluted  detergent  mixture, wring thoroughly and wipe off. If the protective covering for the LCD display becomes soiled, wipe with a dry, soft cloth. If  the stain is difficult to remove, try moistening the cloth slightly.  Do not use detergents for cleaning. The use of detergents may adversely affect the performance of the pen. Also, do not use organic solvents, as they may cause surface discolouration.  Replacing the Pen NibWhen the pen nib becomes worn down so that it is 1mm or less in length, replace it as shown in the illustration below. If  the pen nib becomes worn down and angular in shape, it can easily damage the surface of  the protective covering of the LCD display.     Caution    Caution
 26  Message  Display TroubleshootingWhat to DoPrior  to  connecting  the  product,  if  you  have  a  monitor  that you have been using, connect it and then adjust the horizontal frequency to  30–80 kHz and  the  vertical frequency  to  50 –75 Hz. Connect the product. - Verify that the video signal cable* is connected.- Verify that the video signal cable connector pins are not bent or broken. • When the computer goes in to power saving mode, move the mouse or press any keyboard key. • Verify that the computer graphics board is correctly installed.  • Verify that the video signal cable is connected.• Verify that the video signal cable connector pins are not bent or broken.• If  you are using a cable other than the video signal cable that was included with the product, this message may appear prior to  the computer  going  into  power-saving  mode. The  product is not out of  order. Use the cable that was included to connect the product.  The RGB – RGB cable is not connected.The composite video cable is not connected.Set the refresh rate so that it is 70Hz or less. The  refresh  rate  may be  adjusted  at the  Screen  Profile  dialog box for your computer.  Referenceー P.11ーーーP.11ーP.9P.9、11P.11ー If One of These Messages Should Appear...   Troubleshooting* Video signal cable indicates both USB cables (see page 9).       Caution
 27  If One of These Conditions Should Appear...ConditionThe power lamp lights up orange or orange and blue. The power lamp doesn’t light up and the screen doesn’t display. The screen doesn’t display even when the power switch is turned on. The picture is distortedThe picture appears waveyThe picture flickersThe picture is not clearThe picture appears  doubled  or  in triplicateThe picture is out of positionThe picture size is incorrectThe picture is dark. Waves and vertical stripes appear in the picture. The picture colour is uneven.The colour white  does  not  display as white. What to Do• Verify that the video signal cable is connected.• Verify that the video signal cable connector pins are not bent or broken. • When the computer goes in to power saving mode, move the mouse or press any keyboard key. • Verify that the computer graphics board is correctly installed.• Verify that the power cable is connected and turn the power switch on. •Adjust the pitch and phase. •Verify  that your  computer  display adapter  is compatible  with the product. •Verify  that  the graphics  mode  and  frequency  for  the  input signal are compatible with the product. •Adjust  the computer’s refresh  rate (vertical  frequency)  for optimal display. •Adjust the contrast and brightness.•Adjust the pitch and phase.•Set your computer’s resolution to SXGA (1280 x 1024). •Do not add an extension to the video signal cable and refrain from using the input selector. •Connect the video signal cable firmly to the connector. •Adjust the pitch and phase.•Adjust  the  horizontal and  vertical positioning. Depending  on the input signal and video card, the picture may not entirely fill the screen.  •Adjust the brightness.•Adjust the pitch and phase.•Adjust the colour temperature.ReferenceP.10-11 ーーーP.10-11ーP.15-18ーP.30P.30P.17P.16-18ーーーP.15-18P.16-18P.16-18P.16-18P.16-17Troubleshooting
 28    The Pen and Side Switch do not Operate Correctly (For Both Windows and Macintosh)ConditionThe  pen  nib produces a  click even when only very lightly coming in contact with the screen. The pen does not produce a click unless excessive pressure is used.  The  pen  nib produces a  click  prior to coming into contact with the screen.The pen nib do not work. The pen cannot be double-clicked using the pen nib. The pressure function cannot be used.What to DoUse  the  control  panel  to  set  the pen  nib  sensitivity  to  Firm setting. Use  the  control panel  to  set  the  pen  nib sensitivity  to  Soft setting.Use  the  control  panel  to  set  the pen  nib  sensitivity  to  Firm setting.When  the  status  lamp  turns  blue  in  response  to  the  pen  nib being moved to close proximity to the screen, either the pen or the tablet is probably defective. Please verify that the status lamp turns blue when the pen nib and side switch are pushed. If  the lamp doesn’t change colours, this probably indicates that either the pen or the tablet is probably defective. If  possible, quickly click in the same area. In the control panel, set the double-clicking interval to a longer setting and set the pen nib sensitivity to a lighter setting. Verify that the double-click speed setting is not too fast in the regular mouse control panel.  Please  refer  to your  software application  and  the store where you  bought  the  application  to  verify whether it  is  pressure function-enabled.  Some applications  have  special  settings  that must  be  established  before  the  pressure  function  becomes operational. The  tablet  driver  probably  is  not installed  properly.  Try  re-installing it. ReferenceP.22P.22P.22P.6ーP.22P.22ーP.12ConditionWhen a replacement computer is purchased or new software is used, the tablet cannot be used. The tablet, which is connected to a USB hub, doesn’t respond. What to DoInstalling the newest version of tablet driver may resolve this problem. The  newest  tablet driver  can  be downloaded from the Wacom homepage. >http://tablet.wacom.co.jp/Some USB hubs cannot recognize tablets. Connect the tablet directly to the computer’s USB port. Referenceー ー General Troubleshooting
 29  Troubleshooting for WindowsConditionEven when connected to the USB port, the pen is inoperable.  When Windows is in DOS full screen mode, moving the pointer with the pen becomes impossible.  If the  mouse  is set for left-handed use in the regular mouse control panel,  the  ability to click with  the pen nib is lost. What to Do•Check the connection of the USB connector. If  using a USB hub connection, try connecting directly to the computer’s USB port.•When  the  product  model  type  appears  in  the  Unknown Device  list, select  it and  click the  Delete button,  canceling  all settings for it. Next, click the Renew button and, following the directions in the New Hardware dialog box, re-install the tablet driver. •If use of the USB  port is advantageous, open the Control Panel folder and then the System folder. Then open, in order, the  Hardware  and  Device  Manager  folders.  Next,  check  and make sure  that USB  (Universal Serial  Bus) Controller  appears in the list that is displayed. If  it isn’t present, it will be necessary to adjust  your  computer. Please consult  your  computer  maker regarding this. When using a DOS mouse, the pen is inoperable. You must use another mouse. Restart Windows. ReferenceP.11ー ーーー Troubleshooting for MacintoshConditionEven when connected to the USB port, the pen is inoperable. The product always reverts to mouse mode and the pressure function cannot be used.  What to Do-Check the connection of  the USB connector. Connect directly to the computer’s USB port.-If  equipped with a USB card, the system software has probably not been installed properly. -If  you have any other high-speed, high-power USB peripherals, connect these and check and see whether they operate properly or not. If  these other units operate properly, this would seem to indicate that the tablet is defective. The tablet driver may not be properly installed. Try reinstalling it. ReferenceP.11ー ーP.12Troubleshooting
 30  General SpecificationsPhysical dimensions(W D H):  344 × 300 × 49 mm (excluding stand)Weight:  4.4kg (including stand) Main unit input voltage:  DC12VPower consumption:  23 W or less (DC12 V)Usage temperature and humidity ranges:  5–35 degrees C, 20–80%RH (conditions where condensation does not form)Storage temperature and humidity ranges:  -10–60 degrees C, 20–90%RH (conditions where condensation does not form) (at 60 degrees C maximum storage humidity is 38%; at 90% humidity, maximum storage temperature is 42 degrees)LCD Display SpecificationsDisplay:  a-Si TFT Active Matrix LCDScreen size:  15 inchesResolution (75Hz Max.):  1024 × 768 dot (XGA), 800 × 600 dot (SVGA), 640 × 480 dot (VGA)Pixel pitch:  0.297(W) × 0.297 (H) mmDisplay dimensions:  304.1 × 228.1mmColor depth:  253 level; 16,190,000 colorsSignal inputs:  Analog RGB input 0.7 Vp-p, 75Ω, straight polarity  Synchronous inputs: TTL level, 2.2 kΩ, polarity freedom (horizontal / vertical separation or com-posite synchronous input)  Synchronous frequency: horizontal: 30 – 56.5 kHz; vertical 45 – 75 Hz.(When resolution is 1024 × 768 dot (XGA), vertical frequency is in the 45-70Hz range)  Scanning method: all non-interlacePlug and Play:  DDC2B*  On rare occasions, light and  dark  dots  may  appear  on a small part of the  display  screen. This  condition  does  not indicate product failure.  *  Afterimages may remain on the screen after still images have been displayed for a long period of time, but these will disappear after a short period of time. Tablet SpecificationsReading method:  Electromagnetic induction methodMaximum reading range:  304.1 × 228.1mmReading resolution:  Maximum 20 lpmm (0.05 mm)Reading accuracy:   +/- 0.5 mm; four corners( 20mm wide, 80mm long from esch corner of  four "L" shaped area) to be +/- 2.0 mm.Maximum reading height:  5mmData transfer rate:  Maximum 100 points per secondPressure level:  512 levelsInterface:  USB   󰯥Specification Grip Pen Specifications )Pressure functions:  Pen nib switchPen nib switch type/retraction motion:  Non-retractable/0.2 mm or lessLoad when pen nib is switched on:  30 g or lessPhysical dimensions and weight: 12.5 × 147.5 mm, 10 g
 31    Obtaining Technical Support   If  you  have  any  problem  with  DTF-521,  first  check  the  appropriate  setup  chapter  in  this  guide to make sure  the  unit is installed  correctly. Then  review  the Troubleshooting  section within this manual and the online Help, your problem may be described there and you can try the solution offered. You can also check the product Frequently Asked Questions on the Wacom web site.FAQ: http://club.wacom.co.jp/wacom-en/servlet/support.user.Swusr101Sv00Support StaffIf  you  think  your  DTF-521  Interactive  Pen  Display  is  not  working  properly,  contact  the  Wacom authorized distributors in your area (Check  your area distributor on the Wacom web site: http://www.wacom.com.sg/distributor/dist_index.html), or contact us as the following:Asia/Pacific & OceaniaBy Inquiry Form: http://club.wacom.co.jp/support-en/servlet/support.user.Swusr200Sv00Tel: ++81-3-5309-1588Fax: ++81-3-5309-1514
RADIO AND TELEVISION INTERFERENCEThe equipment described in this manual generates, uses, and can radiate radio-frequency energy.  If it is not installed and used properly – that is, in strict accordance with Wacom instructions – it may cause interference with radio and television reception.FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICEThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.You can determine whether the tablet equipment is causing interference by powering it off.  If the interference stops, it was probably caused by the tablet.If your tablet equipment does cause interference to radio or television reception, you may be able to correct the interference by using one or more of the following measures:• Rotate the television or radio antenna until the interference stops.• Move the tablet equipment farther away from the television or radio.• Plug the tablet equipment and computer into an outlet that is on a different circuit from the television or radio.If necessary, consult your Wacom dealer or an experienced radio/television technician for help.Changes or modifications to this product not authorized by Wacom could void the FCC Certification and negate your authority to operate the product.

Navigation menu