Wacom Co PL550 Computer Interactive Pen Display User Manual Manual

Wacom Co Ltd Computer Interactive Pen Display Manual

Manual

CAUTIONBe sure to ground the power adaptor cable at the receptacle when plugging in.Do not touch the liquid crystal if leaked; it is irritative. In case of contact, rinse immediately with running waterfor more than 15 minutes. If it went into the eye or mouth, consult physician.WARNINGTurn off the power of the Cintiq 15X in the area where prohibited to use.  It may cause other electronicdevices to malfunction.Do not use the Cintiq 15X in a facility control system that requires extremely high reliability. It may causeother electronic devices to malfunction or, other device may cause the Cintiq 15X to malfunction.Do not open the Cintiq 15X It has the risk of electric shock.HIGH VOLTAGEIf the Cintiq 15X is broken due to fall or hit, do not leave it connected to the power. It has the potential toresult in fire.Only use the AC adaptor that came with your Interactive Pen Display. If a different type of AC adaptor is used,the Interactive Pen Display will not work properly or it may be damaged. Using a different type of AC adaptoralso has the potential to result in fire.Prevent your children from swallowing the UltraPen nib or side switch.  The pen nib or side switch mayaccidentally be pulled out if children are biting on them.UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM1
PrefaceThe Wacom® Cintiq™ 15X is an integrated LCD tablet designed for direct draw-on-screeninterface with your computer.  The Cintiq 15X Interactive Pen Display components include aWacom tablet internally mounted behind a 15.0" diagonal TFT color LCD monitor, and Wacom’sUltraPen®.This manual describes how to install the Cintiq 15X Interactive Pen Display hardware andsoftware.It also describes how to use the Interactive Pen Display and UltraPen.Information on using the Wacom Tablet Control Panel for customizing your tablet and pensettings is available in the Interactive Pen Display online Help, located under the HELP menu inthe Wacom Tablet Control Panel.The following are not included with this product:■Information about your specific computer hardware.■Information about your operating system.■Information about application software.  To use the pressure-sensitivity of the UltraPen withyour favorite drawing application, refer to instructions in that application’s manuals.Please refer also to your computer hardware, operating system, or software application manuals.UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM2
Precautions on handling the Cintiq 15X■For use with DVI, do not use any graphics card that Cintiq 15X can not be used with. It may damagethe Cintiq 15X.■Do not disassemble the Cintiq 15X or pen. This may cause the device to malfunction. In this case,Wacom shall have no responsibility to repair or replace the product.■Do not use or store the Cintiq 15X where:- Temperature changes are severe (e.g., outdoors or inside a vehicle).- The Cintiq 15X and pen are exposed to direct sunlight or heat from an appliance.- The Cintiq 15X and pen are exposed to water or any other kind of liquid.- Temperature or humidity exceeds the specifications.■Do not  block the ventilation holes in the rear panel. It may overheat and damage the Cintiq 15X.■Do not use the Cintiq 15X in a dusty environment. It may damage the Cintiq 15X.■Do not scratch the cover glass of the Cintiq 15X. Avoid placing sharp objects on the glass surface. If thepen tip becomes sharp or angular, it may damage the coating on the cover glass of the Interactive PenDisplay. Please replace the pen nib as necessary.■Do not use detergent to clean the cover glass of the Cintiq 15X—this may alter the surface friction anddeteriorate the handwriting feel.■Do not lift up the Cintiq 15X by holding the stand. It may damage the open-close mechanism of the stand.When you lift up the Cintiq 15X, be sure to hold the main unit casing.■Do not put heavy articles on the Interactive Pen Display; this may damage the cover glass or stand.■Do not place heavy article on the Cintiq 15X cables. Near the cable connectors, do not apply heavy stresson the cables or do not repeat bending the cables.  It may damage the Cintiq 15X.■Do not connect or disconnect the DVI video cable or power cable while the Interactive Pen Display oryour computer is turned on; it may damage the LCD display or computer video card.UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM3
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications.  However, there is noguarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one of the following measures:  -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.  FCC Caution:  To assure continued compliance, (example - use only shielded interface cables when connecting tocomputer or peripheral devices).  Any changes or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate this equipment.
4Table of ContentsChecking Packed Components 5Installation 6LCD Monitor InstallationWacom Tablet Software Installation for Windows and MacintoshCalibrating the TabletCintiq 15X Component Functions 10Front ViewRear ViewMounting the Cintiq 15X onto a Mount Arm or Other StandCaring For Your Cintiq 15XUsing the UltraPenUltraPenPen Type Settings in the Wacom Tablet Control PanelReplacing the Pen TipUsing the UltraPen 13UltraPenUsing a PenAdjusting the LCD Monitor 15Factory Presets, Auto Adjust and User SettingsFunctions and Uses of the MENU WindowAdjusting Pitch and PhasePower SavingCaring For Your Cintiq 15X 19Cleaning Your Cintiq 15XReplacing the Pen TipTroubleshooting for Display 20Specifications 22General SpecificationsLCD DisplayTabletUltraPenUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM4
5Checking Packed ComponentsIn your package you will find the following items:USB Cable or RS-232C CableDVI-DVI Cable or DVI-RGB Cable*2Cintiq 15Xmain unitUltraPen with Pen HolderUser’s ManualWacom Software CDContains the Interactive PenDisplay software and aReadme file(Windows/Macintosh)AC Adaptor and CableSide SlitFillers*1*1 *2For Cintiq 15X only. Do not use this for other devices.One either cable is included.*2Please retain the package box for storage or transportation.UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM5
6InstallationLCD Monitor InstallationFirst install the Cintiq 15X as a monitor. Do not connect the USB cable or serial data cable until instructed forthe tablet software installation.➀Turn off your computer.IMPORTANT: Never connect or disconnect the DVI video cable or power cable while your computeror Interactive Pen Display is powered on.  This can damage the LCD display or video card.➁Connect the DVI-to-DVI cable or DVI-RGB cable between the Cintiq 15X and your computer.➂Set the DVI / Analog RGB switch. Turn it up for Analog RGB, and turn it down for DVI.√Connect the AC adaptor to the Cintiq 15X.➄Connect the AC adaptor power cable and plug the adaptor into an AC outlet.IMPORTANT■Do not use any cable that did not come withthe Cintiq 15X.  It may damage the Cintiq15X.■For use with DVI, do not use any graphicscard on which Cintiq 15X can not be used.It may damage the Cintiq 15X.■Do not connect or disconnect the DVI videocable or power cable while the InteractivePen Display or your computer is turned on;it may damage the LCD display orcomputer video card.DVI-I connectorDVI/analog RGB switchDC inputUSB connectorRS-232C connectorCable hooksto AC outletGroundVideo cardDVI-DVI or DVI-RGB cableTo USBportRear Panel of your computerTo serial portUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM6
7≈Turn on the power switch of the Cintiq 15X.  The power lamp will light green , and then turns orange.∆ Turn on your computer to start your operating system.➇By looking at the Cintiq 15X display, configure the monitor settings for proper size and color resolution.(The recommended resolution is 1024 x 768. Other settings may give unsatisfactory results.)The color pallet and number of colors are as follows:- High Color (16 bit), 65,536 color- True Color (24 bit), 16,770,000 color approximateThe number of colors is constrained by the performance of your computer or graphics card. Refer to thedocumentation of the manufacturer for details.➈To install the Wacom tablet software, turn off your computer and connect the USB cable or serial datacable.Tablet Software Installation for Windows* and Macintosh➀After connecting all cables of the Cintiq 15X, turn on the Cintiq 15X and your computer. Allow the operat-ing system to fully load.➁Insert the Wacom Tablet CD into the CD-ROM drive. The Wacom tablet software installer menu shouldautomatically display.  If the menu does not display, double-click on the INSTALL icon (located on the CD).Click on the INSTALL CINTIQ button and follow the prompts to install the driver software.➂Windows: After the driver installation is complete, make sure you can use your UltraPen on the tablet dis-play to move the screen cursor.Macintosh: After the driver installation is complete, restart your Macintosh. You will be able to use yourUltraPen on the tablet display to move the screen cursor.Be sure to read the README file for late braking news.If you have trouble in the Tablet software installation, refer to the TROUBLESHOOTING CHAPTER in the online HelPin the Wacom Tablet CD. You can also open the online Help from the HELP menu from the WACOM TABLETcontrol pane.Precede to CUSTOMIZING YOUR CINTIQ 15X – THE BASICS.*Windows 95 and laterUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM7
8Customizing Your Cintiq 15X – The BasicsOpening the Wacom Tablet Control PanelThe Wacom Tablet Control Panel makes it easy to customize your Interactive Pen Display and UltraPen.To open the control panel:Windows: Click on the Windows Start button and choose Programs. From the Wacom Tablet group,choose the Wacom Tablet option.Macintosh: From the Apple menu, choose Control Panels and then Wacom Tablet.When you open the control panel, an icon for the UltraPen is displayed in the Tool List and the appropriatetabs are displayed. To customize the UltraPen, make your changes to the tab controls.On Windows systems, be sure to click APPLY or OK to save your changes.Note: Application-specific settings are for advanced users. Refer to the online Help for more information oncreating and using application-specific settings.Displays applications withcustomized settings.Current selections are highlighted.  Wedges emphasize the relationshipbetween tab settings and the selected tool and application.Displays an iconfor the UltraPen.The pull-down menus access avariety of control panelfeatures.For Windows only:OK saves changes and closesthe control panel.  Cancelcloses the control panelwithout saving changes.  UseApply to save changes withoutclosing the control panel.Displays online Help for thecontrol panel.Tabs display settings for theselected application.Resets the selected tab to itsfactory default valuesReturns a tab to its previouslysaved or last applied settings.Copies settings from one toolor application to another.Windows screen capture shown.UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM8
9Calibrating the TabletYou will need to calibrate the tablet in order to line up the screen cursor position with the position of theUltraPen on the Interactive Pen Display. This is required to adjust for parallax caused by the clear plasticoverlay. After setting the tablet in its working position, follow the procedure below to calibrate the tablet.➀From the Wacom TabletControl Panel, select theCALIBRATION tab.If you are working withmultiple monitors, selectthe Monitor that corre-sponds to the tablet’s LCDdisplay.➁Click on the CALIBRATE...button to display the moni-tor calibration screen..➂Hold the pen as you nor-mally do, and use the pentip to click on the cross-hairs in the upper-left cor-ner.Then click on the cross-hairs that are displayed inthe lower-right corner.(You will need to click Ap-ply or OK for the changesto take effect.)NOTE: The calibration settingapplies to all applicationsUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM9
10Front View   - On a TFT liquid crystal display, a very small number of pixels may be permanently illuminated or not illuminatedat all.  This does not mean that the display is defective.    - When pressing the LCD panel hard it may temporarily cause moire to appear. This does not mean the display isdefective.    - When a still image is displayed for a long period of time, an after image may temporarily remain.Power SwitchIntegrated Tablet andLCD Screen *2Status LampPower LampPower SwitchTurns the power to the Cintiq 15X on or off.Power LampLights green when power has properly been supplied to the Cintiq 15X. Turns orange or flashes when yourcomputer goes into power management mode and stops sending the video signal to the Cintiq 15X.Status LampLights green when a pen switch is pressed.Pen HolderCan attach and detach at the location shown in the above drawing.  When attached, it can be moved up anddown, or rotated. It can also be attached to the left side.Side Slit FillersCloses the side slit on which the pen holder is not attached.ENTER ButtonPress this button when you select or exit an item in MENU*2 window.POWERSTATUSENTEREN-MENU*1ENTER Button+ (plus) Button- (minus) ButtonMENU*1 ButtonPen Holder*2You can select the language to display the MENU window. ☞ P11Cintiq 15X Component FunctionsSide SlitFillerUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM10
11StandThe angle of the stand can beadjusted to one of 47 levelsbetween the horizontal closedposition (17° from horizontal).Rear ViewStand LeverPulling this lever allows the stand tomove freely. Releasing the lever locksthe stand in place.Connector LidIMPOTANTDo not lift up the Cintiq 15X by holding the stand. It may damage the open-close mechanism of thestand.  When you lift up the Cintiq 15X, be sure to hold the main unit casing.Be sure to close the stand when packing the Cintiq 15X Interactive Pen Display. If you do not closethe stand, the notched mechanism may be damaged during transportation and storage.+ (plus) Button, - (minus) ButtonPress this button when you change the item or settings in MENU window.MENU ButtonOpens and closes the MENU window.Integrated Tablet and LCD ScreenThe LCD monitor and tablet sensor function* as an integrated input and output device.The LCD resolution is 1024 x 768 pixels at 16,777,216 colors. The tablet sensor reports coordinates, pressure,switch, and eraser information.The characteristics of the LCD may cause an inaccurate display of color tones. It is recommended that thetones be checked on a color-adjusted CRT monitor.Be careful to avoid catching yourfinger in the gap of the movableportion of the stand.CAUTION*As the tablet of the Cintiq 15X emits electromagnetic waves in a certain frequency, if another tablet is closely placed tothe Cintiq 15X, the screen cursor may jitters or jumps around. To solve this problem, place the tablet away from theCintiq 15XUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM11
12Cintiq 15X Component FunctionsUsing the side slit fillerTo attach the side slit filler:➀Adjust the botom of the side slit filler to the bottom of the side slit.➁Fill in the slit pressing the top of the side slit filler.➀➁To remove the side slit filler:Pull out the top of the side slit filler using a screwdriver.UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM12
13CAUTIONWhen mounting the Cintiq 15X ontoan arm or other stand, be sure tofollow the instructions in thedocumentation of the manufacturer. Ifimproperly installed, it may causeCintiq 15X to fall and be damaged.Mounting the Cintiq 15X onto a Mount Arm or Other StandThe Cintiq 15X conforms to VESA FPMPM standard.You can dismantle the stand and mount the Cintiq 15X onto a VESA conformed mount arm or other stand.(Screw gap: 75 mm, Thread pitch: 0.7 mm )➀Turn off your computer and the Cintiq 15X, and disconnect all cables from the Cintiq 15X.➁Place the Cintiq 15X on a flat table facingdown. Be sure to spread a soft cloth be-tween the table and Cintiq 15X front panelto protect the surface.➂ Unscrew and dismantle the stand.√Using the four screws of Cintiq 15X stand,firmly mount the Cintiq 15X onto the arm.➄Connect all cables by following the instruc-tion on page 6.unscrewUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM13
14UltraPenHold the UltraPen as you would a pencil. Make sure the side switch is in a convenient location where youcan press it with your thumb or forefinger, but won’t accidentally press it while drawing.Using the UltraPenPen TipWhen the pen tip is within proximity (5 mm or 0.2 in) of the active area, the tablet reports:- The x, y coordinates of the pen tip.- The pressure applied to the pen tip.- Whether a side switch is on or off.When pressure is applied to the pen tip, the tip switch is turned on and the pen simulates amouse button click.EraserTo use the eraser, hold the UltraPen upside down. When the eraser is within proximity of the active area, thetablet reports the x, y coordinates and the pressure applied to the eraser.The eraser can be used as an eraser or assigned to another function, depending on the application.  The tab-let distinguishes the tip switch from the eraser switch.Side Switch and Second Side SwitchThese switches are programmable, and can be used to perform the same click and double-clickfunctions as the tip switch. The switches are turned on when pressed, and are otherwiseturned off. Please refer to the online Help for more information on side switch settings.Tip SwitchEraserSide SwitchSecond  Side SwitchUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM14
15Using a PenPointing and SelectingMove the UltraPen above the Cintiq 15X Interactive Pen Display screen to position the screen cursor.The cursor instantly jumps to the new location (absolute positioning). Press the pen tip on the InteractivePen Display screen to make a selection.NOTE: If the screen cursor is not aligned with the pen tip, you will need to calibrate the InteractivePen Display.ClickingTap the Interactive Pen Display screen once with the pen tip, or touch the pen to the display screen withenough pressure to generate a mouse click.Double-ClickingPress the upper side switch (Windows systems) or quickly tap the Interactive Pen Display screen twice in thesame place with the pen tip. Double-clicking is easier when the pen is perpendicular to the tablet screen.DraggingSelect an object, then slide the pen tip across the Interactive Pen Display screen to move the object.ErasingIn supporting applications, the pen’s eraser works like the eraser on a pencil. In text applications,use the eraser to select text, then lift the eraser from the tablet to delete the text.Using the UltraPenUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM15
16Adjusting the LCD MonitorFactory Presets, Auto Adjust and User SettingsFactory Presets: The Cintiq 15X is programmed with some prevailing display modes as defaults so that theCintiq 15X can display the image with the bast quality based on the incoming signals for most cases.Auto Adjust: When the Cintiq 15X first receives the signals with a display mode out of factory presets, theAuto Adjust automatically adjusts horizontal/vertical position, phase and pitch if horizontal frequency is be-tween 28 to 64 kHz and vertical frequency is between 48 to 75 Hz. The adjusted settings will be stored in theCintiq 15X to display in the best condition when the  same signals are received next time. This is effective foranalog RGB only.  While the Auto Adjust is working, except for the power switch, all buttons will not work.User Settings: For any display modes, once you manually set the display by using the MENU window, thesettings will be stored in the Cintiq 15X to display in the same condition when the Cintiq 15X receives thesame signals next time.Functions and Uses of the MENU WindowTo open the MENU Window: Press the MENU button ' '.To switch an item: Press the + (plus) button ' ' or the - (minus) button ' ' .To change setting in the item: Press the ENTER button ' ' to activate the item, then press the + (plus) button'', - (minus) button ' '  and/or ENTER button ' '.To exit the MENU Window: Press the MENU button ' '.CONTRAST ContrastAdjusts contrast.BrightnessAdjusts black level. Phase(Analog RGB only)Calibrates phase when theAuto Adjust is notenough. ☞ P18 Pitch(Analog RGB only)Calibrates pitch when theAuto Adjust is not enough.☞ P18BRIGHTNESSUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM16
17 Vertical Position(Analog RGB only)Adjusts vertical position ofdisplay. Color ManagementYou can select one from9300, 6500, 5000 deg. inKelvin and user setting.You can change the usersetting by selecting theicon ' '.In the user setting, changered and blue to calibratecolor centering on green.To exit, select the icon''. Horizontal Position(Analog RGB only)Adjusts horizontal positionof display. Menu PositionMoves the MENU windowto one of nine positions. ResetAUTO ADJUST resets thehorizontal/verticalposition, phase and pitchto the condition that theAuto Adjust did.RECALL resets the displayto the factory default.Selecting the icon ' 'exits the Reset windowwithout resetting any-thing. Backlight LevelAdjusts the backlightlevel. LanguageSelects one language fromsix options: English,German, French, Spanish,Italian and Japanese.COLORBACKLIGHTUSER ADJUSMENTAdjusting the LCD MonitorUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM17
18Adjusting Pitch and Phase (analog RGB only)Some models of computer or graphics card may not allow the Auto Adjust to fully work when the Cintiq is firstconnected.  If the display does not fit the LCD panel border or some part of text show blurred, adjust pitch andphase by following the below procedure. The resolution 1024 x 768 is recommended for the best effect.➀From the Wacom TabletControl Panel, select theCALIBRATION tab.If you are working withmultiple monitors, selectthe Monitor that corre-sponds to the tablet’s LCDdisplay.➁Click on the CALIBRATE...button to display the moni-tor calibration screen..➂Open the MENU windowand select Pitch.√Adjust the Pitch level sothat the adjustment pattern(fine vertical stripes) dis-plays evenly.➄Select Phase and adjustthe Phase level so thatplayed the adjustment pat-ter shows clearly.≈After completing the ad-justments press the  EN-TER button ' ' and MENUbutton ' ' to exit.UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM18
19HINT (Windows only): You can also adjust Pitch and Phase in the display of closing the Windows.If the pitch is not calibrated, vertical moire appears in the darkened area. And if the phase is nocalibrated, the darkened area riffles.Power SavingCintiq 15X conforms to VESA and Energy Star power saving guidelines.  When the Cintiq is used with a VESADPMS (display Power Management signaling) compliant computer or graphics card, it will automaticallycomply with the below Power Saving parameters.Power Saving ModePower ONStandby modeSuspend modeOFF modeV-syncYesYesNoNoVideoActiveBlankedBlankedBlankedPower Consumption45W max.  5W max.  5W max.  5W max.Power LampGreenOrange/GreenOrange/GreenOrangeH-syncYesNoYesNoAdjusting the LCD MonitorUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM19
20To insert a new nib: To remove the old nib:Prevent your children from swallowing the UltraPen nib or side switch. The pen nib orside switch may accidentally be pulled out if children are biting on them.CAUTIONSlide it straight into the barrel of thepen. Firmly push the nib until it stops.The new nib will slide into the correctposition.Clasp it with the o-ring tool that camewith your UltraPen and pull the old nibstraight out of the pen.Caring For Your Cintiq 15XCleaning Your Cintiq 15XTo clean the Cintiq 15X casing, use a soft cloth with mild detergent (such as dish washing liquid) diluted withwater.  Do not use paint thinner, benzine, alcohol, or other organic solvents to clean the Cintiq 15X casing orpen.Do not use detergent to clean the cover glass. This may alter the surface friction and deteriorate thehandwriting feel.  To clean the cover glass of the Cintiq 15X, use a soft, dry cloth. If necessary, slightly moistenthe cloth with water and try again. When cleaning, apply only a light amount of pressure to the cover glassand do not make the surface wet.Replacing the Pen TipThe pen tip will wear with normal use. When the nib gets too short, you can replace it with one of the extranibs that came with your UltraPen. If the pen tip wears and becomes angular, it may damage the coating onthe cover glass of the Cintiq 15X Interactive Pen Display. To avoid this, periodic nib replacement is recom-mended.UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM20
21Troubleshooting for DisplayIf you encounter problems with the Cintiq display, refer to the following tables. Your problem may bedescribed here, and you can try the solution offered.For problems regarding tablet or pen, refer to the Troubleshooting chapter in the online Help that can beaccessed from the Wacom Tablet control panes.       Problem               HintThe message "OUT OF SCAN RANGE"appears..■The message "NO INPUT SIGNAL"appears..■The power lamp show orange LEDlight, or flashes orange and greenThe message "CABLE DISCON-NECTED" appears.■The power lamp does not light andnothing displays.■Nothing displays even thoughpower switch is turned on..The frequency of input signals do not match the Cintiq 15X.  Connect differentmonitor and set the horizontal frequency to some value between 28 to 64 kHzand vertical frequency to same value between 48 to 75Hz.■Check the video signal cable, check the connector pins if bent or broken.■If your computer is in the power management mode, move the mouse or hitany key on the keyboard.■Check if the graphics card is properly installed.■Check the video signal cable, check the connector pins if bent or broken.■The video signal cable used may not be the one came with the Cintiq 15X.Please use the cable came with the Cintiq 15X.■Check the power cable and if power switch is ON.■For DVI, check if DVI/analog RGB switch is turned to the DVI side. ☞ P 6Restart your computer after switching to the DVI side.UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM21
22          Problem                  Hint■Display riffles.■Display flickersDisplay is not clear.Display is doubled or tripled.■Display and CLCD panel are notlined-up.■Display size is not correct.Display is dark.■Display riffles or shows moire.■Color is not even.White color doesn't show white.■Adjust pitch and phase. ☞ P16, 18■Check if display adaptor or graphics card matches the Cintiq 15X specifications.■  Adjust the refresh rate of your computer.■Adjust contrast or brightness. ☞ P16■Adjust pitch and phase. ☞ P16, 18■Set the refresh rate to XGA (1024 x 768)■Do not extend the video signal cable. So not use a input selector.■Connect the■Adjust pitch and phase. ☞ P16, 18■Adjust horizontal and vertical position. ☞ P17Some graphics card may not show display in proper size.■Adjust brightness. ☞ P16■Adjust backlight. ☞ P17■Adjust pitch and phase. ☞ P16, 18Adjust color. ☞ P17UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM22
23General SpecificationsPhysical dimensions (WxDxH): 405x340x53mm  (excluding the stand)Weight: 4.9kg (including the stand)Main Unit input Voltage: DC18VPower consumption: 45W or less (DC18V)Operating temp. & humidity: 5 to 35 deg. C, 80%RH  (non condensing)Storage temp. & humidity: -10 to 60deg. C, 90%RH  (non condensing) (maximum storage humidity is 38% at60 deg.C, and maximum storage temperature is 42 deg. C at 90% humidity)LCD DisplayDisplay: a-Si TFT active matrix LCDScreen size: 15 inResolution (75Hz Max.) 1024x768 pixels (XGA), 800x600 pixels (SGA), 640x480 pixels (VGA)Pixel pitch: 0.297(W) x 0.297(H)mmColor depth: 256 levels: 16,777,216 colors (24 bit)Signal Inputs: Analog RGB: - 0.7Vp-p, 75ohms, positiveSynchronous signals: TTL level, 2.2kohms, free polarity (H/V separate or complexsync.Digital signals: DVISynchronous frequency: H--30 to 65kHz, V--50 to 75HzPlug and Play DDC2BStd. Display Modes (default) All scan modes are N.I.Number of programmable 18 (excluding defaults)On a TFT liquid crystal display, a very small number of pixels may be permanently illuminated or not illuminated at all.This does not mean that the display is defective.SpecificationsRes. dots x lines720x400640x480640x480640x480800x600800x600832x6241024x7681024x7681024x768H. freq. (kHz)31.5031.4735.0037.5037.8846.8749.7348.3660.0260.24V. freq. (Hz)70.0859.9466.6775.0060.3275.0074.6060.0075.0374.93H/V pol.-/+-/--/--/-+/++/+-/--/-+/+-/-UM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM23
24TabletReading technology: Electromagnetic give and receive methodActive area: 304.1 x 228.1mmResolution: 20 lpmm (0.05mm) max.Accuracy: +/-0.5mm,  four corners ( 7 mm wide, 25 mm long from each corner of four "L"shaped areas) to be +/-1.0mmMaximum reading height: 5mmMaximum report rate: 205 points/sec. max (RS-232C), 100 points/sec. (USB)Pressure levels 512 levelsCommunication I/F USB, RS-232CUltraPenUP-813ESide switch: Double (rocker switch)Pressure: Tip and EraserTip trave: 0.1mm max.Eraser tip travel: 2 mm approximateTip switch ON load: 30g max.Physical dimensions, weight: 11.4 dia x 140.5 mm, 12gramsUP-714W (optional)Side switch: SiglePressure: Tip onlyTip trave: 0.1mm max.Tip switch ON load: 30g max.Physical dimensions, weight: 9.0 dia x 140.0 mm, 8 gramsUM-0251/Cintiq AP.pm65 01.7.31, 9:27 PM24

Navigation menu