Wave Wireless AIRPRO-SE Data modem User Manual MPE and TX Power Settings

Wave Wireless Corporation Data modem MPE and TX Power Settings

Contents

MPE and TX Power Settings

ADDENDUM TO THE AIRPRO-SE USER MANUALTRANSMITTER POWER SETTINGSThe maximum output power allowed by FCC Rule Part 15 depends on power spectral density(PSD) at a given output power setting, on antenna gain, and on the amplitude of emission bandedgeenergy in restricted bands starting at 2483.5 MHz and 2390 MHz.Data Rate: 19.2 kB/sFrequency/Channel Maximum Ouput Power(MHz, Plan, Channel) 0 dBi 8 dBi 15 dBi 24 dBi2401.868, P3, C1 (lowest) 23 dBm 23 dBm 23 dBm 23 dBm2478.227, P3, C48 23 dBm 23 dBm 15 dBm 5 dBm2479.851,P3, C49 23 dBm 8 dBm 0 dBm not used2481.476,P3, C50 (highest) 23 dBm 0 dBm not used not usedAll others not listed 23 dBm 23 dBm 23 dBm 23 dBmData Rate: 64 kB/sFrequency/Channel Maximum Ouput Power(MHz, Plan, Channel) 0 dBi 8 dBi 15 dBi 24 dBi2404.468, P2, C1 (lowest) 26 dBm 26 dBm 26 dBm 24 dBm2474.652, P1, C14 25 dBm 25 dBm 25 dBm 23 dBm2478.552, P2, C20 16 dBm 0 dBm not used not used2479.851,P3, C49 (highest) 3 dBm 8 dBm 0 dBm not usedAll others not listed 25 dBm 25 dBm 25 dBm 25 dBmData Rate: 128 kB/sFrequency/Channel Maximum Ouput Power(MHz, Plan, Channel) 0 dBi 8 dBi 15 dBi 24 dBi2407.067, P1, C1 (lowest) 27 dBm 26 dBm 26 dBm 24 dBm2472.053, P3, C7 (highest) 25 dBm 25 dBm 23 dBm 15 dBmAll others not listed 28 dBm 28 dBm 27 dBm 24 dBmData Rate: 256 kB/sFrequency/Channel Maximum Ouput Power(MHz, Plan, Channel) 0 dBi 8 dBi 15 dBi 24 dBi2411.446,P1, C1 (lowest) 25 dBm 23 dBm 23 dBm 8 dBm2461.476, P1, C6 26 dBm 26 dBm 23 dBm 17 dBm2472.107, P3, C4 (highest) 8 dBm not used not used not usedAll others not listed 28 dBm 28 dBm 27 dBm 24 dBm
Compliance with RF Exposure Guidelines in FCC Rule para. 1.1307(b)1The AIRPRO transmitter must meet the RF exposure requirements described in paragraph1.1307(b)1 of FCC’s Rules. The specific requirement for a transmitter of this type is that themaximum permissible exposure level (MPE) meets the limits for “GeneralPopulation/Uncontrolled Exposure “ (Table 1, para. 1.1310). The required MPE is 1.0 mW/cm2.For each antenna used with the AIRPRO transmitter, the antenna gain and maximum outputpowerare used to calculate the distance from the antenna at which MPE is exceeded. The installer shalltake all reasonable steps to maintain this separation distance between the antenna and personnel.Calculating Minimum Separation Distances to meet MPE RequirementsE2/377 = S, W/m2Specification: 1 mW/cm2 = 10 W/m2, Emax = 61.4 V/mEv/m = (30*P*G)0.5 / d, P= power in watts, G = ant. gain over isotropic, d = distance, metersd = (30*P*G)0.5 /61.4Ant Gain, dBi RF In, dBm Minimum Dist, cm0.0 28.0 7.18.0 28.0 17.815.0 27.0 35.524.0 24.0 70.9

Navigation menu