Waxess DM1000C Dual Mode CDMA 850/1900MHz & 2.4GHz FHSS Phone User Manual d mode ct draft 6
Waxess Inc. Dual Mode CDMA 850/1900MHz & 2.4GHz FHSS Phone d mode ct draft 6
Waxess >
Contents
- 1. Users Manual Part I
- 2. Users Manual Part II
Users Manual Part II
d mode ct draft 6.book Page 22 Wednesday, March 2, 2005 10:33 PM Short Message Service (SMS) This feature–available only with cellular service–lets you send and receive text messages to other SMS enabled cellular phones through the CEL connection at the base or the cordless handset. Check with your service provider for availability. Note: If an incoming call arrives, the terminal (handset or base) on which you are using this feature will not ring. Answer the incoming call with a terminal that is not being used. The options available in SMS are: • Write new • Saved • In Box • Storage status Note: Due to the data access process in the D Mode CT, the phone may not respond instantly when keys are pressed. This is normal operation, and any delay is no more than one or two seconds. WRITE A NEW MESSAGE 1 Press MENU, scroll to Messages, and press Select. SMS, and press Select. Write new is highlighted. 3 Press Select. 2 Scroll to 4 Use the keypad to write a message up to 160 characters long, including spaces and special characters. See “Enter names and characters” on page 18.) 5 When you finish writing, press OK. The new message submenu appears with Send, Edit, Save. If the phone receives a call or someone initiates a call on another handset while you are writing a message, the message is automatically stored in Saved messages. You can access the message later, edit the message, if needed, then send the message by following the steps below. SEND A NEW MESSAGE 1 Write a message, then press OK. Send, Edit, and Save appear. Send, and press Select. 2 Scroll to D mode CT DRAFT 6 22 Copyright © 2005 Waxess d mode ct draft 6.book Page 23 Wednesday, March 2, 2005 10:33 PM Recipient No.? appears. 3 Enter the phone number of the recipient and press OK. To send a message to a number that is stored in the phone book, press MENU, scroll to the entry you want, and press Select. Note: Verify that the CEL line is not in use before sending the message. A confirmation message appears. Then, the SMS menu appears. If you want to save the message. 4 Scroll to Save, press Select, then press Yes. The message is stored in Saved messages for easy viewing later. OR Press No to exit. SAVE A NEW MESSAGE OK. 2 Scroll to Save, and press Select. 1 After writing a message, press The message is stored in Saved messages for easy viewing later. Then the SMS menu appears again. VIEW SAVED MESSAGES 1 Press MENU, scroll to Messages, and press Select. 2 Scroll to SMS, and press Select. 3 Scroll to Saved, and press Select. 4 Scroll to the message you want to read, and press Select. RECEIVE A MESSAGE When the D Mode CT receives a text message, it sounds the ring tone for an incoming CEL call. The message goes to the Inbox. CHECK THE INBOX FOR READ AND UNREAD (NEW) MESSAGES 1 Press MENU, scroll to Messages, and press Select. 2 Scroll to SMS, and press Select. 3 Scroll to Inbox, and press Select. 4 Scroll to UnRead Messages, and press Select. If you have no unread messages, an error tone sounds. OR 5 Scroll to D Mode CT DRAFT 6 Read messages, and press Select. 23 Copyright © 2005 Waxess d mode ct draft 6.book Page 24 Wednesday, March 2, 2005 10:33 PM 6 Scroll to the message you want to read, and press Select. When you exit the Unread Messages list, any messages that have not been viewed are automatically stored in the Read Messages list. Be sure to view all unread messages before exiting the Unread Message list. REPLY TO A MESSAGE 1 While reading a message, press Select. 2 Scroll to Reply, and press Select. Write a reply the same way as you write a new message, press OK, then Select to send the message. FORWARD A MESSAGE Select. 2 Scroll to Forward and press Select. 1 While reading a message, press 3 Enter the recipient’s number and press OK. To send to a number from the phone book, press MENU, scroll to the entry you want, and press Select. Note: Forwarding a message can only be done through a CEL connection. DELETE A MESSAGE While reading a message, press Select, scroll to Delete, and press OK. CALL THE MESSAGE SENDER While viewing a message, press Select, scroll to Call, and press Select. The phone dials the number automatically on the cellular service. CHECK MEMORY STATUS 1 Press MENU, scroll to Messages, and press Select. 2 Scroll to Storage status, and press Select. Memory status appears. D mode CT DRAFT 6 24 Copyright © 2005 Waxess d mode ct draft 6.book Page 25 Wednesday, March 2, 2005 10:33 PM The Memory status feature shows how many SMS messages are saved in memory or stored in the inbox. Storage capacity is limited, and there is no indication that the memory is full. When the message memory gets full, no more SMS messages can be received, so it is important to clear the memory frequently. D Mode CT DRAFT 6 25 Copyright © 2005 Waxess d mode ct draft 6.book Page 26 Wednesday, March 2, 2005 10:33 PM 4 More features • Caller ID This feature helps identify incoming calls and requires subscription through your service provider. When Caller ID is active, your phone may display the caller’s name and phone number if the landline or cellular service supports it. Note: Caller ID and Call Waiting are usually included with cellular calling plans, but landlines may require a separate subscription. Check with your service provider for details. Caller ID information SINGLE CEL OR TEL CALL In Standby, the Caller ID normally shows new and total calls received. On a single incoming call, Caller ID shows the time and date, the caller’s name, and the number. CEL or TEL blinks depending on the type of call–cellular service or landline. SIMULTANEOUS CEL AND TEL CALL When both landline and cellular services are active, the phone can receive both types of calls at the same time or very close together. When that happens, Caller ID information for both calls appears in the display and the call arriving first is on top. CALL WAITING If you receive another call during a call in progress, information for both calls appears in the displays Call in progress D mode CT DRAFT 6 26 Copyright © 2005 Waxess d mode ct draft 6.book Page 27 Wednesday, March 2, 2005 10:33 PM Press FLASH/DEL to answer the new call. Press FLASH/DEL again to return to the first call. If the current call is on the CEL line and another call arrives also on the CEL line, a “C” blinks in the display. New call If the current call is on a CEL line and the new call is on the TEL line, the “C” remains solid, and the “T” indicator blinks. If you receive a call waiting signal during the conference call, press FLASH to answer the call. Check the log Press to scroll through the log from newest to oldest. Press to scroll through the log from oldest to newest. The log holds up to 50 entries. Dial a number 1 Scroll to a name/number displayed, and press Select twice. The number appears in the display. If the number’s area code is the same as an area code stored in the phone memory (see “Area codes” on page 10), the area code may not appear. If the area code is required for dialing, press # to add the area code to the number. If the number 1 is also required for dialing, press * to add 1 to the beginning of the number. 2 Press CEL or TEL to make the call. Save a number 1 Scroll to a name/number displayed, and press Select. 2 Scroll to Save, and press Select. 3 Enter a name if needed (see “Enter names and characters” on page 18) and press OK. 4 Edit the number if needed and press OK. The Distinctive Ring menu appears. 5 Scroll to the setting you want and press The Speed Dial menu appears. D Mode CT DRAFT 6 27 OK. Copyright © 2005 Waxess d mode ct draft 6.book Page 28 Wednesday, March 2, 2005 10:33 PM 6 Scroll to the speed dial number that you want for this new entry and press OK. OR Press Skip to exit. A tone confirms that the entry is stored in the phone book, and the name and number appear in the display. 7 Press OFF twice to return to Standby. Delete a number ONE BY ONE 1 Press to scroll through the log from newest to oldest. Press to scroll through the log from oldest to newest. 2 Stop on the number you want, press 3 Scroll to Delete, and press Select. A confirmation message appears. Select. 4 Press Yes to delete the number. A tone confirms your choice and the Caller ID log appears. OR Press NO and the Caller ID menu appears. DELETE ALL 1 Press , then press Select. 2 Scroll to Delete ALL and press Select. A confirmation message appears. 3 Press OR Press Yes to delete all data from the Caller ID log. NO and the Caller ID menu appears. • Page and Intercom Page The Page feature lets you locate the handset if it is misplaced, but it also can be answered by the handset. Only the base can initiate the Page feature. D mode CT DRAFT 6 28 Copyright © 2005 Waxess d mode ct draft 6.book Page 29 Wednesday, March 2, 2005 10:33 PM 1 Press INTERCOM on the base, scroll to the handset you want to page, and press PAGE. OR To send a page to all registered handsets, select All and press PAGE. The Page All feature is only available at the base. The handset beeps up to 60 seconds, and Paging Base appears in the display. 2 On the handset receiving the page, press ANSWER to connect with the base. On Intercom appears in the display. 3 Press Exit to stop the page without connecting to the base through the Intercom. For Page All, the page stops when any handset responds to the page, and there is no intercom connection. Intercom The Intercom feature is available on the handset and the base. 1 Press INTERCOM, scroll to the handset you want (or base), and press PAGE. The handset or base beeps up to 60 seconds and Handset 1 (or 2, 3, or 4) appears in the display. Paging 2 To answer: • On the handset, press ANSWER to connect with Intercom. • On the base, lift the corded handset, press ANSWER, or press SP-PHONE to connect with the Intercom. During an Intercom connection, use Mute to turn off the microphone at the base or on the handset. • Two-line calling The Dual Mode Communication Terminal is a two-line phone that offers unique calling features because it can be used to make or receive two separate calls at the same time; one call on the landline (TEL) service and the other on the cellular (CEL) service. D Mode CT DRAFT 6 29 Copyright © 2005 Waxess d mode ct draft 6.book Page 30 Wednesday, March 2, 2005 10:33 PM Quick reference chart When calling on: Line Second call can be made: Using Line Base Cellular Any cordless handset Landline Cordles handset Cellular Base Landline Cordless handset Cellular Any remaining Landline cordless handset Base Landline Any remaining Cellular cordless handset Cordless handset Landline Base Cordless handset Landline Any remaining Cellular cordless handset Cellular Make two separate calls 1 Use the base (corded handset or speakerphone) to place a call–for example, a landline (TEL) call (see “Make a landline call” on page 13). 2 Place a cellular (CEL) call, for example, with a handset that is not in use (see “Make a wireless call” on page 13). • The display on any handset or base not in use shows XXX in use; XXX means base or handset in this case. • The two calls are completely separate and cannot be conferenced. • If Barge-In is on (see “Barge-in” on page 31), and the first call is made from a cordless handset on a landline, other handsets can join the call by pressing TEL; but the base can not join the call. Receive two separate calls 1 When a call comes in–for example, a landline (TEL) call, answer it normally. In this example, use the corded handset on the base. See “Answer a landline call” on page 15. D mode CT DRAFT 6 30 Copyright © 2005 Waxess d mode ct draft 6.book Page 31 Wednesday, March 2, 2005 10:33 PM 2 If a cellular (CEL) call comes in, use a cordless handset and press CEL to answer it. Remember that the corded handset and the speakerphone on the base cannot be used at the same time. Call waiting with two calls 1 While a call is in progress (as in the above example) and the landline (TEL) receives another call, Call waiting appears in the display and any other cordless handsets not in use will ring. 2 To answer the call, press FLASH/DEL on the base, or TEL on any handset not in use. If the new call comes in on a different line, press the appropriate key (CEL or TEL) regardless of whether you are using the base or a handset. • Barge-in After placing a landline (TEL) call with a cordless handset, this feature allows up to three other registered cordless handsets to join the call. Before using the Barge-In feature, read the following information. • The D-Mode CT comes with the Barge-In feature set to off–it must be activated before use. • If power to the base is interrupted, Barge-In must be reactivated. • The first cordless handset to place the call is the “master” and fully controls the call. Other registered handsets that join the call are “slaves” and can only join or exit the call. • Barge-In works only for cordless handsets during a landline (TEL) call and is not operable on the base. Note: Remember that with Barge-In activated, privacy may be compromised. Any registered handset can join the call, but there is no indication that another handset joined the call. D Mode CT DRAFT 6 31 Copyright © 2005 Waxess d mode ct draft 6.book Page 32 Wednesday, March 2, 2005 10:33 PM Quick reference chart When calling on: Second call can be made: Using: Line: Line Base1 Cellular • 1 or more cordless handsets Landline2,4 1 cordless handset Cellular • Up to 3 cordless handets • base Landline2,3,4 2 or more cordless handsets Cellular Not available Base Landline • 1 cordless handset Cellular2,4 1 cordless handset Landline • 1 cordless handset • base Cellular2,4 2 or more cordless handsets Landline • 1 cordless handset • base Cellular2,4 Notes: Base includes the speakerphone and corded handset. In Barge-In mode, Page/Intercom between base and cordless is disabled during a call. Conference call feature disabled for CEL and TEL Call transfer disabled Use of two or more cordless handsets on cellular line is only available in Cellular Only mode. Set up Barge-In 1 Press MENU, scroll to Setup, and press Select. 2 Scroll to Barge-In and press Select. 3 Scroll to ON, and press OK. A tone confirms the choice and the Setup menu appears. 4 Press Exit twice to return to Standby. D mode CT DRAFT 6 32 Copyright © 2005 Waxess d mode ct draft 6.book Page 33 Wednesday, March 2, 2005 10:33 PM Use Barge-In 1 Verify that Barge-In is activated, then use one handset to place a call. 2 After the call is answered, press the call. TEL on any handset to join • Cellular only An advantage of the Dual Mode Communication Terminal is that when landline services are unavailable or not needed, it can operate with only the cellular service. In this mode, up to four cordless handsets can join in a conference call. Set up Cellular only 1 Disconnect the telephone cord from the base. 2 Press MENU, scroll to Setup, and press Select. 3 Scroll to Cellular Only, and press Select. 4 Scroll to On, and press Select. A tone confirms the choice, and the Setup menu appears. Turn off Cellular only If landline services are needed, deactivate this feature first. 1 Connect the telephone cord. 2 Press MENU, scroll to Setup, and press Select. 3 Scroll to Cellular Only, and press Select. 4 Scroll to Off, and press Select. A tone confirms the choice, and the Setup menu appears. • Power back-up Power back-up for the base is an optional feature (not required to operate this product) that allows the base to operate for up 30 minutes even (depending on battery condition) if AC power is disrupted. If you install batteries for the Power Back-up feature you can check the condition of the batteries while they are installed. 1 On the base, press MENU, scroll to Setup, and press Select. 2 Scroll to Battery Level, and press Select. If no batteries are installed, an error tone sounds. D Mode CT DRAFT 6 33 Copyright © 2005 Waxess d mode ct draft 6.book Page 34 Wednesday, March 2, 2005 10:33 PM Current power level for the batteries appears. Full power Low power 3 Press Exit to return to the Setup menu. Notes about Power Back-up • Use new batteries. • There are no indicators to inform you when the phone is operating under regular power or backup power. • If you disconnect the AC power adaptor, Power Back-up starts automatically. • Check battery levels frequently, and replace the batteries if the charge level drops below one half of fully charged. • After every power outage, check the batteries and replace them as needed. • Actual operating time using Power Back-up varies depending on the condition of the batteries. D mode CT DRAFT 6 34 Copyright © 2005 Waxess 5 Precautions Before you read anything else, please observe the following precautions. Warning! Waxess Inc. DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture. Rechargeable Nickel-Metal-Hydride Battery Warning • This equipment contains a rechargeable Nickel-Metal-Hydride battery. • Nickel is a chemical known to state of California to cause cancer. • The rechargeable Nickel-Metal-Hydride battery contained in this equipment may explode if disposed of in a fire. • Do not short-circuit the battery. • Do not charge the rechargeable Nickel-Metal-Hydride battery used in thi s equipment in any charger other than the one designed to charge this battery as specified in the owner's manual. Using another charger may damage the battery or cause the battery to explode. Rechargeable Nickel-Metal-Hydride Battery Must Be Recycled or Disposed of Properly The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Warning! The cords on this product and/or accessories contain lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. D Mode CT 35 Copyright © 2005 Waxess • Important safety instructions When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons: 1 Read and understand all instructions. 2 Follow all warnings and instructions marked on the product. 3 Unplug this product from the wall outlet before cleaning. Use a dry cloth for cleaning without liquid or aerosol cleaners. 4 Do not use this product near water; for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. 5 Do not place this product on an unstable cart, stand, or table. The telephone may fall, causing serious damage to the unit. 6 Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect the product from overheating, these openings must not be blocked or covered. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided. 7 This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. 8 Do not allow anything to rest on the power cord. Do not locate this product where the cord will be damaged by persons walking on it. 9 Do not overload wall outlets and extension cords, as this can result in the risk of fire or electrical shock. 10 Never push objects of any kind into this product through cabinet slots, as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 11 To reduce the risk of electric shock, do not disassemble this product. Take it to qualified service personnel when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used. 12 Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A When the power supply cord is damaged or frayed. B If liquid has been spilled into the product. D mode CT 36 Copyright © 2005 Waxess C If the product has been exposed to rain or water. D If the product does not operate normally when following the operating instructions. (Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive repair work by a qualified technician.) E If the product has been dropped or the cabinet has been damaged. F If the product exhibits a distinct change in performance. 13 Do not use the telephone to report a gas leak in the vicinity of the leak. ADDITIONAL BATTERY SAFETY PRECAUTIONS Caution: To reduce the risk of fire or injury to persons by the battery, read and follow these instructions: 1 Use only the battery pack specified in the owner's manual. 2 Do not dispose of the battery pack in a fire. The cell may explode. Check the Nickel Metal Hydride battery disposal package insert for disposal instructions. 3 Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. 4 Exercise care in handling the battery in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns. 5 Charge the battery pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in the owners manual provided for this product. 6 Observe proper polarity orientation between the battery pack and battery charger. SAVE THESE INSTRUCTIONS! Important Electrical Considerations Unplug all electrical appliances when you know an electrical storm is approaching. Lightning can pass through your household wiring and damage any device connected to it. This phone is no exception. D Mode CT 37 Copyright © 2005 Waxess The FCC Wants You To Know Changes or modifications to this product not expressly approved by Waxess, or operation of this product in any way other than as detailed by the owner's manual, could void your authority to operate this product. our telephone complies with Part 68 of FCC Rules. You must, upon request, provide the FCC registration number and the REN to your telephone company. Both numbers are on the base unit. Note: You must not connect your phone to: • coin-operated systems • most electronic key telephone systems This device complies with Part 15, 22 (800 MHz CDMA), 24 (1900 MHz CDMA), and 68 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Privacy of communications, may not be ensured when using this phone. To insure the safety of users, the FCC has established criteria for the amount of radio frequency energy various products may produce depending on their intended usage. This product has been tested and found to comply with the FCC's exposure criteria. For body worn operation, the FCC RF exposure guidelines were also met when used with the accessories supplied or designed for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines and should be avoided. Range Your new phone is designed to achieve the maximum possible range by transmitting and receiving according to the highest specifications set forth by the FCC. We have rated this phone to operate at a maximum distance with the qualification that the range depends upon the environment in which the telephone is used. Many factors limit range, and it would be impossible to include all the variables in our rating. The Maximum Range rating of this phone is meant to be used as a means of comparison against other range claims. D mode CT 38 Copyright © 2005 Waxess Telephone Line Problems The FCC has granted the telephone company the right to disconnect service in the event that your phone causes problems on the telephone line. Also, the telephone company may make changes in facilities and services which may affect the operation of your unit. However, your telephone company must give adequate notice in writing prior to such actions to allow you time for making necessary arrangements to continue uninterrupted service. If you are having trouble with your telephone service, you must first disconnect your phone to determine if it is the cause of your problem. If you determine that it is the cause, you must leave it disconnected until the trouble has been corrected. Radio Interference Radio interference may occasionally cause buzzing and humming in your cordless handset, or clicking noises in the base. This interference is caused by external sources such as TV, refrigerator, vacuum cleaner, fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If these noises continue and are too distracting, please check around your home to see what appliances may be causing the problem. In addition, we recommend that the base not be plugged into a circuit that also powers a major appliance because of the potential for interference. Be certain that the antenna on the unit is fully extended when needed. In the unlikely event that you consistently hear other voices or distracting transmissions on your phone, you may be receiving radio signals from another cordless telephone or other source of interference. If you cannot eliminate this type of interference, you need to change to a different channel. Finally, it should be noted that some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference. D Mode CT 39 Copyright © 2005 Waxess More than One Cordless Telephone If you want to use more than one cordless telephone in your home, they must operate on different channels. Press the channel key to select a channel that provides the clearest communication. Cordless Telephone Privacy Cordless telephones are radio devices. Communications between the handset and base of your cordless telephone are accomplished by means of radio waves which are broadcast over the open airways. Because of the inherent physical properties of radio waves, your communications can be received by radio receiving devices other than your own cordless telephone unit. Consequently, any communications using your cordless telephone may not be private. Installation Considerations SELECTING A LOCATION Before choosing a location for your new phone, there are some important guidelines you should consider: • The location should be close to both a phone jack and continuous power outlet. (A continuous power outlet is an AC outlet which does not have a switch to interrupt its power.) • Keep the base and handset away from sources of electrical noise such as motors or fluorescent lighting. • Be sure there is sufficient space to fully extend the base antenna. • The base can be placed on a desk or tabletop or mounted on a standard telephone wall plate. • You should charge your new phone for 12–15 hours before completing the installation or using the handset. D mode CT 40 Copyright © 2005 Waxess Telephone Line Outlets There are two types of phone outlets: Modular Jack Most phone equipment available now uses modular jacks. Phone cords are fitted with a molded plastic connector which plugs into this type of jack. If you do not have modular phone jacks, contact your local telephone company for information about their installation. Hardwired Jack Some equipment is wired directly to a phone jack, and these types of installations require a modular jack converter. This type of installation is not difficult; however, you should contact your telephone dealer or a telephone supply store for advice about the proper adapter or converter for your particular situation. Connecting the Telephone Cords Consider these safety guidelines before connecting the telephone cords: Caution: • Never install telephone wiring during a lightning storm. • Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected. • Use caution when installing or modifying telephone lines. Applying Power to the base This phone requires an AC outlet, without a switch to interrupt power, and the included AC adapter. To relieve strain on the DC plug when the phone is placed on a desk or table, wrap the power cord around the strain relief notch on the bottom of the base. Note: Place the power cord so that it does not create a trip hazard, or where it could become chafed and create a fire or other electrical hazards. D Mode CT 41 Copyright © 2005 Waxess • I.C. Notice TERMINAL EQUIPMENT Notice:This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. Notice:The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five. RADIO EQUIPMENT The term "IC" before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. “Privacy of communications may not be ensured when using this telephone.” D mode CT 42 Copyright © 2005 Waxess 6 General information This phone complies with FCC Parts 15 and 68. AC Adaptor Information: Base Model AD-48091000 Input voltage 120V AC, 60Hz. 0.3A Output voltage 9V DC, 1000 mA Charger Model RGD41090500 Input voltage 120V AC, 60 Hz, 0.15A Output voltage 9V DC, 500 mA Battery Information: Ni-MH, 3.6V, 1300mA Frequency: CDMA 800/1900 MHz Handset/ base 2.4GHz Weight: Handset 4.9 oz. (without battery) 7.3 oz. (with battery) Base 1 lb., 13.7 oz. with corded handset Dimensions: Handset 6-3/4” x 2” x 1-1/4” (height, width, depth) Base 3-1/4” x 7-3/4” x 7-7/8” (height, width, depth) FCC Registration Number: T.B.D. Specifications, features, and availability of optional accessories are all subject to change without prior notice. Approved patents: 6,766,175. Patents pending: 09/991 and 10/156,439 D Mode CT 43 Copyright © 2005 Waxess Index barge-in ....................... 31 quick reference chart ........ 32 set up .......................... 32 use .............................. 33 base unit batteries .........4 call answer landline .............. 15 answer wireless .............. 14 conference call ............... 17 make landline call ............ 13 make wireless call ........... 13 caller ID ....................... 26 delete number ................ 28 dial number ................... 27 information .................... 26 save number .................. 27 cellular only ................. 33 set up .......................... 33 turn off ......................... 33 contact information ....... iv controls and switches base ............................. iii handset .......................... ii cordless handset ............5 battery indicator ...............6 charge the battery .............6 install batteries .................5 page ............................. 28 pause ........................... 14 phone book .................. 18 call from phonebook ........ 20 enter characters ............. 18 enter numbers ............... 19 phonebook distinctive ring ............... 19 edit names and numbers ... 19 enter Caller ID numbers .... 20 enter speed dial number ... 20 power on ........................ 3 precautions .................. 35 distinctive ring ........19, 20 feature list .................... iv hold .............................. 15 included items ................1 intercom ....................... 29 location ..........................2 desk or tabletop ................2 wall mount ......................3 D Mode CT redial ........................... 14 safety instructions ....... 36 set area codes .................... 10 dialing mode ....................7 earpiece volume ............. 13 corded handset .......... 13 cordless handset ........ 14 speaker phone .......... 13 handset registration ......... 11 deregister ................ 12 menu shortcuts ............ 47 messages SMS ............................ 21 check inbox .............. 23 delete a message ....... 24 forward ................... 24 memory status .......... 24 receive .................... 23 reply ....................... 24 save a new message ... 23 send ....................... 23 send a new message ... 22 write ....................... 22 voice messages .............. 21 check voicemail ......... 21 set up ..................... 21 mute ............................ 15 44 Copyright © 2005 Waxess register ...................11 language ....................... 11 ringer tone ......................8 night volume .............. 9 volume ..................... 9 time and date ...................7 unit name ..................... 11 signal level .....................5 sim card install .............................1 notes .............................1 specifications ............... 43 speed dial ..................... 14 standby screen ...............4 text messages .............. 21 transfer ........................ 15 two-line calling ............. 29 call waiting .................... 31 make calls ..................... 30 quick reference chart ........ 30 receive calls ................... 30 D Mode CT 45 Copyright © 2005 Waxess Notes D Mode CT 46 Copyright © 2005 Waxess Menu Shortcuts French Spanish Portuguese Name the Unit Base Handset Tone/Pulse Tone Pulse Barge-In Off On Signal Level Battery Level Cellular Only On Off LCD Contrast Memory Phone book Find name Add new entry Caller ID Ringer/Key Beep Ringer tone CEL Ring Tone TEL Ring Tone Ringer Volume Night Volume Key Beep Time and Date Time Time Format Date Date Format Setup Distinctive Ring On Off Area Code Area Code 1 Area Code 2 Area Code 3 Language English D Mode CT Messages Voicemail CEL Voicemail TEL Voicemail Voicemail Setup VM Number (CEL) VM Number (TEL) SMS 47 Copyright © 2005 Waxess D Mode CT User Guide ####### Copyright © 2005 Waxess
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 27 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:ae5045c8-3ab6-4228-93d5-a9faef775268 Modify Date : 2005:04:21 17:23:31-07:00 Create Date : 2005:04:21 17:23:18-07:00 Metadata Date : 2005:04:21 17:23:31-07:00 Document ID : uuid:e0010259-6253-4f75-ad66-cdb22fdddf67 Format : application/pdf Title : d mode ct draft 6.book Creator : PScript5.dll Version 5.2 Author : Owner Producer : Acrobat Distiller 5.0 (Windows)EXIF Metadata provided by EXIF.tools