Wayne Dalton HHT-3720 Door Control Transmitter User Manual M Production Drawings 300623 3
Wayne Dalton Corporation Door Control Transmitter M Production Drawings 300623 3
Users Manual
Re: Certification for Wayne-Dalton Corp. 3BTM Transmitter
Model: 3BTM
FCC ID: KJ8HHT-3720
IC: 350A-3BTM3720
USER'S MANUAL INFORMATION
(PRELIMINARY)
The User's Manual is in preparation. The following material will be contained in the
manual:
FCC ID: KJ8HHT-3720 IC: 350A-3BTM3720
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
WARNING: Changes or modifications not expressively approved by the party
responsible for compliance could void the user's authority to operate the equipment.
The term “IC:” before the radio certification number only signifies that Industry Canada
technical specifications were met.
Large transmitter
1) Press program button on DoorMaster ™ light fixture or idrive ™ powerhead; light fixture
LED will light or powerhead will beep once.
2) Press and hold the desired transmitter button(s); LED will go off or powerhead will beep once.
3) Press and hold same transmitter button(s) again; door should operate.
NOTE: Any of the three transmitter buttons can be programmed to activate the door. In multi-door
installations, each button or a combination of two buttons pushed at the same time can be
3 - Button Transmitter
Model #3BTM
Always keep moving door in sight and away from people and
objects until it is completely closed. To prevent serious injury
or death, avoid standing in the open doorway or walking
through the doorway while door is moving.
Never let children operate or play with door controls. Keep
remote controls away from children. Fatal injury could result
should a child become trapped between the door and the floor.
Upon activation by either wall station or transmitter, door will move in following manner:
1. If closed, door will open. If open, door will close.
2. If closing, door will stop, reverse, and return to open position. Next activation will close.
3. If opening, door will stop. Next activation will close.
4. If an obstruction is encountered or an out of balance condition is detected while closing, door will
reverse, return to open position, and DoorMaster ™ light fixture will flash 3 times or idrive will beep 3 times.
Next activation will close door.
5. If an obstruction is encountered or an out of balance condition is detected while opening, door will
stop, and DoorMaster ™ light fixture will flash 3 or 4 times or idrive ™ will beep 3 or 4 times .
Next activation will close door.
NOTE: The operator can be activated by up to six remote control devices (including wall station and
keyless entry controls). If a seventh control is programmed, one of the programmed controls will be
overwritten and will no longer activate the operator. To clear the programming of all remote control
devices, press and hold the DoorMaster ™ light fixture program button or idrive ™ powerhead program
button for approximately ten seconds. When the DoorMaster ™ light fixture LED goes out or
idrive™ beeps three times, then all controls are erased.
P/N 300623
Door Activation
Transmitter is now programmed to operator.
NOTE: idrive™ model only: The first transmitter ccommand after programming, will only open
the door through a three inch up/down cycle. Normal door operation will then occur on all
subsequent transmitter commands.
To program the Transmitter:
programmed to activate a separate door.
Transmitter Programming
button
The Following steps describe the process to change a transmitter's security code. This process
only works for transmitters with a "U" in their model number, such as "3BTM-0000 U"
1. Press and hold the large button on the transmitter that you want to change. The RED LED will
flash once and then turn off.
2. Continue to hold the button until the RED LED begins to flash (approx. 10 seconds).
3. When the RED LED flashes, immediately release the button and then immediately press and
hold the button again. The RED LED will now come on steady.
4. Continue to hold the button until the RED LED begins to flash (approx. 5 seconds).
5. When the RED LED flashes, immediately release the button. The RED LED will blink three times.
6. The code for this button has now been changed to a new randomly generated code.
7. You must now program this transmitter to the garage door operator. See" Transmitter Programming".
Changing Transmitter's Code
WARNING! During programming the garage door may operate.
Keep people and objects clear of the moving door to prevent
door damage or possible personal injury.
NOTE: For a new transmitter, you must change its security code before it can be
programmed to the DoorMaster ™ or idrive™ operator.
program butt on
Program button
LED
DoorMaster ™ idrive™