Wayne Dalton KYE5-3720 Door Control Transmitter User Manual EX 03123 Q3 KEP3 Owners Manual

Download:
Mirror Download [FCC.gov]
Document ID	524121
Application ID	y6YWieKcNMjIQ3ZASUBiZg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.81kB (260146 bits)
Date Submitted	2005-03-16 00:00:00
Date Available	2005-03-16 00:00:00
Creation Date	2005-03-11 13:00:08
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2005-03-11 13:00:08
Document Title	EX-03123_Q3_KEP3_Owners Manual..PDF
Document Creator	PScript5.dll Version 5.2.2
Document Author:	liepa

Mounting
Pre-drill a 5/64 pilot
hole 3/4" deep
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a residential environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Pre-drill a 5/64 pilot
hole 3/4" deep
Drilling Template
For Keyless Entry
START HERE
PLEASE READ ALL INSTRUCTIONS
THOROUGHLY TO FAMILIARIZE
YOURSELF WITH THE PROGRAMMING
PROCEDURE BEFORE BEGINNING.
SAVE THESE INSTRUCTIONS FOR
REFERENCE WHENEVER YOU WISH
TO CHANGE YOUR PERSONAL
IDENTIFICATION NUMBER (PIN)
Before your Wireless Keypad will be able
to operate the opener, there are several
programming steps that have to be
completed.
FCC WARNING
To comply with FCC rules, adjustment or
modification of transmitter is prohibited.
THERE ARE NO USER SERVICEABLE
PARTS EXCEPT FOR BATTERY
REPLACEMENT.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
WARNING
NOTE: With new installations, it is
recommended that the keyless entry be
programmed before mounting to wall.
Locate Keyless Entry Unit: within sight of door,
at a minimum height of 5 feet so it cannot be
reached by small children, and away from all
moving parts of the door.
Choose a convenient location that does not
interfere with the normal opening and closing
operation of the door, such as the door jamb.
CAUTION: The keypad
should be mounted a
minimum of 5 feet from
the floor to keep it out
of the reach of small
children.
Two screws are included
for proper mounting into
wood or other similar
material. If you're
mounting into some other
material, consult a
building contractor to
insure proper hardware is
used for a secure
mounting.
Once you
have
determined
the
mounting
location,
use the
drilling
template
to
determine
hole
positions
and drill a
5/64" pilot
hole
3/4" deep for the two mounting screws.
Snap open the Keyless Entry case with a coin.
Separate the front case from the back case.
Mount the back case and secure with screws
provided. Do not over tighten the screws as
this may bend or damage the back case. Install
and snap the front case onto the back case.
Remove paper backing from "Changing
Personal Identification Number" label and apply
label to a clean surface inside garage.
How Your Keyless Entry
Operates Your Opener
MODEL 3966
Wireless Keyless Entry System
The following explains how your Keyless Entry
can be used to OPEN, CLOSE, START, and
STOP your door.
1. Enter your 5-digit PIN (personal identification
number); door will begin to move
NOTE: If you inadvertently enter an incorrect
code, the door will not move To Reset, press
and hold the "7/8" and "9/0" buttons for 2
seconds and reenter your PIN number.
2. Unit remains active for next 25 sec.
Pressing any key, will stop the door if
opening, and stop or reverse the door if
closing.
Battery Replacement
Under normal operating conditions, the
battery should be changed once every 12
months. Dispose of used batteries
properly. To replace battery perform the
following steps:
A. Snap open case with a coin and remove
old batteries.
B. Replace batteries (two CR2032 or
equivalent) and snap case together.
Front Case
Your new Model 3966 Wireless Keyless Entry
contains a state-of-the-art wireless digital
transmitter capable of operating an unlimited
number of compatible garage door openers.
For added security, your Wireless Keyless Entry
utilizes a "rolling code" technology that, each
time the transmitter communicates with the
receiver, sets a new code, selecting from
millions of combinations, reducing the possibility
of electronic equipment causing unwanted
access.
For proper operation it is important that
you follow the programming directions
and sequence as written.
Wayne-Dalton Corp.
One Door Drive „ Mt. Hope, OH 44660
888-827-3667
(2) Coin Cells
Batteries (CR2032)
Rear Case
Coin Slot
Programming or Changing Personal Identification Number
program button
program button
dr ve
Torsion
dr ve
program button
DoorMaster
program button
Quantum
ClassicDrive
A. With new installations, it is recommended that the keyless entry be programmed
before mounting to wall, otherwise proceed to step B.
B. Unit should be programmed with garage door in the down position. For the iDrive
openers, pull the emergency disconnect handle to the manual operated position (lower
position).
C. Press the program button on the garage door opener to switch the opener to the
transmitter learn mode (see illustrations above). Opener will remain in the learn mode
for at least 30 seconds.
D. Press the desired five digit PIN (PERSONAL IDENTIFICATION NUMBER) number,
(example: 1-2-3-4-5). Garage door opener should beep or lamp should blink. For the
iDrive openers, return the emergency disconnect handle to the motor operated
position (upper position). Wait 5 seconds and press any button; the door should
move. Programming is now complete.
Always keep moving door in sight and
away from people and objects until it is
completely closed. NO ONE SHOULD
CROSS THE PATH OF THE MOVING
DOOR.
NOTE: IF, AT ANY TIME, AN ERROR WAS MADE IN ENTERING THE CODES, SIMPLY PRESS AND
HOLD BOTH THE "7/8" AND "9/0" BUTTONS FOR 2 SECONDS TO RESET THE KEYLESS ENTRY.
REPEAT THE ABOVE PROCEDURES.
Never let children operate or play with
door controls. Keep all controls away
from children.
Note: One 3966 Keyless Entry can be programmed to open multiple garage door openers. To program
for additional openers, repeat steps A thru D above except input a different five digit PIN number for each
additional opener.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2005:03:11 13:00:08-05:00
Modify Date                     : 2005:03:11 13:00:08-05:00
Page Count                      : 1
Creation Date                   : 2005:03:11 18:00:08Z
Mod Date                        : 2005:03:11 18:00:08Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : liepa
Metadata Date                   : 2005:03:11 18:00:08Z
Creator                         : liepa
Title                           : EX-03123_Q3_KEP3_Owners Manual..PDF

EXIF Metadata provided by EXIF.tools