Wayne Fueling Systems WAYNETRACII User Manual correction for installation manual section one

Download:
Mirror Download [FCC.gov]
Document ID	108979
Application ID	NHWzmPqw+eAzQ7c3xzKcXQ==
Document Description	correction for installation manual section one
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.18kB (14784 bits)
Date Submitted	2000-07-12 00:00:00
Date Available	2001-03-01 00:00:00
Creation Date	2000-07-12 08:51:23
Producing Software	Acrobat PDFWriter 4.05 for Windows NT
Document Lastmod	0000-00-00 00:00:00
Document Title	\\Wd4\tp_lib2\Manuals\HARDWARE\CAT\920472 Vista Easy Pay Installation\Vista Easy Pay Text Rev C\Sec_1.ps.pdf
Document Creator	Adobe FrameMaker+SGML - [\\Wd4\tp_lib2\Manuals\HARDWARE\CAT\920472 Vista Easy Pay Installation\Vista Easy Pay Text Rev C\Sec_1.fm]
Document Author:	JIMHARD

Section
Before You Start
1.1
Introduction
This manual explains how to install the EasyPAY™ retrofit kit in selected models of Wayne™ Vista 90
series dispensers. This includes all Models V390, V395, V490 and V590 except those with 2/ and 3/
prefix numbers.
By following this instruction manual in the sequences presented, you will be assured of a successful install. For best results, perform the steps in the sequence given for the particular kit or kits that are being
installed.
Important: These retrofit kits require installation of several wiring and hardware assemblies. Any
installation or modification must comply with the requirements of the National Electrical
Code (NFPA 70), the Automotive and Marine Service Station Code (NFPA 30A) and any
other applicable codes.
Refer to the information in Table 1-1 for identification of the EasyPAY™ retrofit kits.
1-1
July 2000
Part No. 920472 Rev. C
Section 1: Before You Start
Table 1-1 EasyPAY™ Retrofit Kits for Vista
Part Number
887122-001
Description
EasyPAY Retrofit Kit, Vista DS
Important: You must wear a static wrist strap, part number 916962 or equivalent, securely attached
to an earth ground, when handling any circuit board, electronic component or assembly,
or when reaching into the site controller or dispenser computer enclosure. Do not use
power tools.
No Modifications:Modifications to this device shall not be made without the written consent of
Wayne Division, Dresser Equipment Group. Unauthorized modifications may void the authority
granted under Federal Communications Commission Rules permitting the operation of this device.
1.2
Unpacking and Inspection
Complete the following steps:
1.
Before opening any cartons, count the number of cartons and verify the carton count against the
supplied packing list.
2.
Inspect the cartons for damage made during transit.
3.
File claim information with the carrier on the bill of lading.
4.
Retain cartons suspected of damage for future claim purposes.
Caution:
You must wear an anti-static wrist strap, part number 916962 when removing electronic
components from static packages. Attach the wrist strap securely to an earth grounding point to prevent
possible damage from static electricity.
5.
Remove all equipment from the shipping cartons and carefully inspect for visible damage.
Note: Any damage should be brought to the attention of the carrier and claims made immediately.
Return all equipment to the respective cartons for protection until actual installation is made. Save all
cartons until it is certain that return shipments are not required.
6.
1.3
Check supplied graphics (such as ad panel and dial face graphics) prior to start of installation.
Returning Damaged Components
Parts or components returned to the factory under warranty or for repair are subject to damage if not packaged properly. Complete the following steps to return parts or components to the factory.
1.
Place electronic components in an anti-static bag and in the original shipping cartons for return
shipment to the factory.
Note: If original shipping cartons are not available use a sturdy cardboard container and suitable
packing materials such as anti-static polyethylene foam or bubble pack, to ensure the component is
firmly packed.
2.
Include a Return Parts Tag with the defective component describing the particular problem with the
part.
1-2
Part No. 920472 Rev. C
July 2000
Section 1: Before You Start
3.
Make sure adequate insurance is provided when returning parts to the factory.
WARNING: If the parts or components arrive at our factory in a damaged condition and it is
determined that the damage is a direct result of inadequate or improper packaging, the damage will not
be covered under the original warranty and the customer or distributor will be held responsible for the
cost of repairs necessary to correct or replace the damaged parts.
1.4
Required Tools
Refer to Table 1-2 for a list of tools required to install the EasyPAY retrofit kit.
Table 1-2 Required Tools
1.5
Quantity
Description
Phillips Screwdriver (medium and small)
Slotted Screwdriver (medium and small)
1/4 inch Nut Driver
3/8 inch Socket Wrench
Diagonal Cutters
Anti-static Wrist Strap
Wire Stripper
Needle Nose Pliers
Pin Pusher
Power Ratings
The EasyPAY installation does not change the existing dispenser power rating.
1-3
July 2000
Part No. 920472 Rev. C
Section 1: Before You Start
1-4
Part No. 920472 Rev. C
July 2000

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 4
Creator                         : Adobe FrameMaker+SGML - [\\Wd4\tp_lib2\Manuals\HARDWARE\CAT\920472 Vista Easy Pay Installation\Vista Easy Pay Text Rev C\Sec_1.fm]
Create Date                     : 2000:07:12 08:51:23
Title                           : \\Wd4\tp_lib2\Manuals\HARDWARE\CAT\920472 Vista Easy Pay Installation\Vista Easy Pay Text Rev C\Sec_1.ps.pdf
Author                          : JIMHARD
Producer                        : Acrobat PDFWriter 4.05 for Windows NT

EXIF Metadata provided by EXIF.tools