Weider Pro Pc3 Bench Webe6399 Users Manual *WEBE63990 157743

Weider-Webe63990-Owner-S-Manual weider-webe63990-owner-s-manual

WEBE63990 to the manual 636faa18-f5fe-4bd9-b5f4-677c8ed79096

2015-05-18

: Weider Weider-Pro-Pc3-Bench-Webe6399-Users-Manual-733505 weider-pro-pc3-bench-webe6399-users-manual-733505 weider pdf

Open the PDF directly: View PDF .
Page Count: 19

Download
Open PDF In Browser	View PDF

Model No. WEBE63990
Serial No.
Write the serial number in the space
above for reference.

USERÕS MANUAL

Serial Number Decal (under seat)

QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you have
questions, or find that there are
missing or damaged parts, we
will guarantee you complete satisfaction through direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians on our customer hot line
will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:

1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
PATENT PENDING

CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.

Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!

Table of Contents
Warning Decal Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Part Identification Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Adjusting the Weight Bench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Exercise Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Muscle Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Ordering Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: A Part List/Exploded Drawing is attached to the center of this manual. Remove the Part List/Exploded
Drawing before beginning assembly.

Warning Decal Placement
The decal shown below has been placed on the weight bench in the indicated locations. If a decal is
missing, or if it is not legible, please call our Customer Service Department toll-free at 1-800-999-3756,
Monday through Friday, 6 a.m. until 6 p.m. Mountain Time, to order a replacement decal. Apply the
replacement decal to the location shown.

Important Precautions

WARNING:
1.

To reduce the risk of serious injury, read the following important
precautions before using the weight bench.

Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.

It is the responsibility of the owner to ensure
that all users of the weight bench are adequately informed of all precautions.

The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental or institutional setting.

Use the weight bench only on a level surface.
Cover the floor beneath the weight bench for
protection.

13. Always secure the weights with the weight

clips when you have mounted them on your
barbell, leg lever or curl barbell.
14. When performing standing exercises, stand
inside the area that is shaded in the drawing.
Always move the bench when performing
standing exercises.

5. Inspect and tighten all parts each time you
use the weight bench. Replace any worn
parts immediately.
6. Keep children under 12 and pets away from
the weight bench at all times.
7.

Keep hands and feet away from moving parts.

Always wear athletic shoes for foot protection while exercising.

Always make sure there is an equal amount
of weight on each side of your barbell and
the curl barbell.

10. Always move the bench out of the way when
performing squat exercises.

15. Always exercise with a partner. When you
are performing bench press exercises, squat
exercises or toe raise exercises, your partner should stand behind you to catch the
barbell if you cannot complete a repetition.

11. The weight bench is designed to support a
maximum of 560 pounds, including the user,
a barbell and weights. Do not place more
than 310 pounds, including the barbell, on
the weight rests. Do not place more than 150
pounds on the leg lever for normal use.

16. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.

12. Always set both weight rests and safety
spotters at the same height.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.

Before You Begin
Thank you for selecting the versatile WEIDER¨ PRO
PC3 Weight Bench. The WEIDER¨ PRO PC3 is
designed to help you develop every major muscle
group of the body. Whether your goal is a shapely figure, dramatic muscle size and strength or a healthier
cardiovascular system, the PC3 Weight Bench will
help you achieve the specific results you want.

Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays). To help us assist you,
please note the product model number and serial
number before calling. The model number is
WEBE63990. The serial number can be found on a
decal attached to the WEIDER¨ PRO PC3 Weight
Bench (see the front cover of this manual).

For your benefit, read this manual carefully before
using the WEIDER¨ PRO PC3 Weight Bench. If you
have additional questions, please call our Customer
Service Department toll-free at 1-800-999-3756,

Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.

Weight Rest

Upright
Right Side

Safety
Spotter
Curl Pad
Barbell
Backrest

Seat

Leg Lever

Weight
Tube

Left Side

Note: The terms Òright sideÓ and Òleft sideÓ are
determined relative to a person sitting on the
bench, and they do not correspond to what is
right and left on the drawings in the manual.

Part Identification Chart - Model No. WEBE63990

R0899A

M4 x 16mm Screw (7)-14

M4 x 25mm Screw (43)-1

M6 x 16mm Screw (3)-6

M10 x 193mm Bolt (22)-2

M6 x 52mm Screw (4)-4

M10 x 70mm Carriage Bolt (34)-2

10 x 68mm Bolt (33)-18

M10 x 75mm Bolt (44)-1

M10 Nylon Locknut (11)-23
M6 Washer (30)-4

M10 Washer (6)-5

Assembly
¥ As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.

Make Things Easier for Yourself!
Everything in this manual is designed to ensure
that the assembly of our products can be completed successfully by anyone. However, it is important to recognize that your new equipment is a
product with many small parts and consequently,
the assembly process will take time. Setting aside
time will help assembly to go more smoothly.

The following tools (not included) are required
for assembly:
¥ Two (2) adjustable wrenches
¥ One (1) rubber mallet

¥ Assembly requires two people.

¥ One (1) standard screwdriver

¥ Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.

¥ One (1) phillips screwdriver
¥ Lubricant, such as grease or petroleum jelly
plus soapy water.

¥ Tighten all parts as you assemble them, unless
instructed to do otherwise.

Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches or a set of ratchet wrenches.

¥ For help identifying the small parts, use the PART
IDENTIFICATION CHART on page 5.

1. Before beginning assembly, make sure you
understand the information in the box above.
Note: Some of the parts described in the assembly steps may come pre-assembled.

1
42

Press 50mm Square Inner Caps (17) into the indicated ends of the Front Leg (19).

Insert an M10 x 68mm Bolt (33) with an M10 Washer
(6) through the lower of the two holes in the Front
Leg (19). Insert an M10 x 68mm Bolt with no
Washer through the upper of the two holes in the
Front Leg. Insert the Curl Post (42) into the Front
Leg.
Slide the bracket on the Bench Frame (5) over the
two M10 x 68mm Bolts (33) and secure it with two
M10 Nylon Locknuts (11). Do not overtighten the
Nylon Locknuts. Set the Curl Post (42) aside until
assembly step 15.

17
2

11
5

2. Press a Stabilizer Endcap (9) into each end of the
Stabilizer (37). Insert two M10 x 70mm Carriage Bolts
(34) through the holes in the Stabilizer. Note that on
one side of the Stabilizer there is an indentation
around each hole. Push the Bolts in from this
side, and then turn the bolt heads towards the
floor.
Slide the bracket on the Bench Frame (5) over the
two M10 x 70mm Carriage Bolts (34) in the Stabilizer
(37) and secure it with two M10 Nylon Locknuts (11).

9
34

3. Attach the Bumper (41) to the Front Leg (19) with an
M4 x 25mm Screw (43).

11
17

Press a 50mm Square inner Cap (17) into each open
end of the Leg Lever (18). Press a 48mm Round
Inner Cap (40) into the weight tube on the Leg Lever.
Lubricate the M10 x 75mm Bolt (44). Attach the Leg
Lever (18) to the bracket on the Front Leg (19) with
the Bolt and an M10 Nylon Locknut (11).

18
41
17

Lubricate

19
40
17
4. Press a 25.4mm x 38.1mm Inner Cap (28) into each
end of both Backrest Tubes (27).

28
28

Press a 25.4mm x 38.1mm Inner Cap (28) into each
open end of the tubes on the Backrest Adjustment
Bracket (39).
Important: Before performing step 5, make sure
the Backrest Tubes are oriented correctly. The
holes marked in the drawing are not centered on the
Tube; they are closer to one edge. This edge must be
pointed towards the floor.

5. Slide an M10 Washer (6) onto an M10 x 193mm Bolt
(22) and then slide the Bolt through the indicated hole
in one Backrest Tube (27).

28
28
Holes are closer to one edge.
Point this edge towards the floor.
5
22

Make sure the Backrest Tube (27) is oriented as
shown in the drawing. Slide the M10 x 193mm Bolt
(22) through the welded tube at the upper end of the
Backrest Adjustment Bracket (39).

Place the backrest tube assembly onto the Bench
Frame (5), so the lower end of the Backrest
Adjustment Bracket (39) rests on one of the adjustment tabs.

Welded Tube

27
6

Slide the second Backrest Tube (27) onto the
M10 x 193mm Bolt (22). Secure the Backrest Tubes
with an M10 Washer (6) and an M10 Nylon Locknut
(11).
6. Slide an M10 Washer (6) onto an M10 x 193mm Bolt
(22).

Holes

27
Welded
Tube

Slide the M10 x 193mm Bolt (22) through the indicated hole in one Backrest Tube (27), then through the
welded tube on the Bench Frame (5) and finally
through the other Backrest Tube. Secure the Bolt with
an M10 Washer (6) and an M10 Nylon Locknut (11).
Do not overtighten the Nylon Locknut; it must be
easy to pivot the Backrest Tubes.

6
6
11
5

Adjustment
Tab

7. Attach the Backrest (15) to the Backrest Tubes (27)
with four M6 x 52mm Screws (4) and four M6
Washers (30).

7
15

4
30

30
4

8. Attach the Seat (14) to the indicated brackets on the
Bench Frame (5) with four M6 x 16mm Screws (3).

5
3
3

9. Press a 3/4Ó Round Inner Cap (12) into each end of
the three Pad Tubes (38).

9
Bracket

Slide a Foam Pad (10) onto one end of each Pad
Tube (38).

Slide the Pad Tubes (38) into the indicated holes in
the Leg Lever (18) and the bracket on the Front Leg
(19). Slide another Foam Pad (10) onto the other end
of each Pad Tube.

19
38
18
10

12
12

12
38

38
12
10

10. Press a 51.8mm x 76.2mm Inner Cap (24) into the
top end of one Upright (1).

Press an Outer Cap (25) onto each end of one Base
(2).
Place the bracket on the lower end of the Upright (1)
over the indicated holes in the Base (2).
1
Note: During the following steps, make sure the
M10 x 68mm Bolts (33) are inserted from the
direction shown in the drawing.
Attach the Upright (1) to the lower arm of the Base
(2) with two M10 x 68mm Bolts (33) and two M10
Nylon Locknuts (11). Do not tighten the Nylon
Locknuts yet.

33
25

Attach the Upright (1) to the bracket on the upper arm
of the Base (2) with two M10 x 68mm Bolts (33) and
two M10 Nylon Locknuts (11). Do not tighten the
Nylon Locknuts yet.
Note: Set the upright assembly aside so it cannot
fall over. In step 13 this upright assembly will be
mounted on the right side of the bench. See the
drawing on page 4 to determine what is the right
and the left side.

11. Press a 51.8mm x 76.2mm Inner Cap (24) into the
top end of the remaining Upright (1).

11
11
11
2

Press an Outer Cap (25) onto each end of the
remaining Base (2).
Place the bracket on the lower end of the Upright (1)
over the indicated holes in the Base (2).
Note: During the following steps, make sure the
M10 x 68mm Bolts (33) are inserted from the
direction shown in the drawing.

Attach the Upright (1) to the lower arm of the Base
(2) with two M10 x 68mm Bolts (33) and two M10
Nylon Locknuts (11). Do not tighten the Nylon
Locknuts yet.

11
25

11
33
2
25

12. Orient the Crossbar (20) with the warning decal facing up as shown. Attach a Barbell Post (35) to the
Crossbar with two M10 x 68mm Bolts (33), a Support
Plate (16) and two M10 Nylon Locknuts (11).

High Side of Bracket

35
33

33
35

Attach the second Barbell Post (35) to the Crossbar
(20) in the same manner. Note: Make sure both
Barbell Posts are oriented with the high side of
the bracket pointing in the same direction.

20
16

Decal
16

11
13. Note: Make sure the two upright assemblies have
the Nylon Locknuts on the side facing the center
of the bench, as described in steps 10 and 11.
Attach the Crossbar (20) to the right upright assembly
(A) with two M10 x 68mm Bolts (33), a Support Plate
(16) and two M10 Nylon Locknuts (11). Make sure
the Bolts are inserted from the side shown in the
upper inset drawing.

A
11

Right
Side
20

Attach the Crossbar (20) to the left upright assembly
(B) with two M10 x 68mm Bolts (33), a Support Plate
(16) and two M10 Nylon Locknuts (11). Make sure
the Bolts are inserted from the side shown in the
lower inset drawing.

B
Left
Side

Tighten the M10 Nylon Locknuts (11) used in
steps 10 and 11.

11
20
B
33

11
14. Press a 1Ó Inner Cap (32) into the open end of each
Weight Rest (21, 52) and each Safety Spotter (26,
53). Insert each Weight Rest and Safety Spotter into
one of the adjustment holes in the Uprights (1). Note:
There is a Left Weight Rest (21) and a Right
Weight Rest (52) because the locking clip should
be on the outside of the Upright. The same is true
for the Left and Right Safety Spotter (26, 53).
Warning: Always insert both Weight Rests at the
same height. Always insert both Safety Spotters
at the same height. Make sure the locking clips
snap into place around the Uprights.

32
21
Locking
Clip
3

32
26

15. Attach the Curl Pad (29) to the Curl Post (42) with
two M6 x 16mm Screws (3).

3
42

16. Make sure all parts are properly tightened before you use the weight bench. The use of all remaining
parts will be explained in Adjusting the Weight Bench starting below.

Adjusting the Weight Bench
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 13 for important information on how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise poster to see the correct form for each exercise.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
USING THE WEIGHT RESTS AND CURL BARBELL
Before beginning an exercise, move the Weight Rests
(21) and the Safety Spotters (26) to a set of holes in the
Uprights that is best suited for that exercise. The selected
holes should represent the lowest point to which you want
your barbell to go during the exercise. Perform the exercise as shown in the accompanying EXERCISE GUIDE.
Note: Make sure the locking clips snap into place
around the Uprights.

1
21
Locking
Clip
26

Important: The Safety Spotters (26) are engineered as
a safety device. Their primary function is to minimize
the risk of injury in case you drop the barbell during
standing exercises. The Safety Spotters are deliberately designed to bend when hit with a barbell loaded
with heavy weights. This is done to minimize the risk
of the barbell jumping off the safety Spotters and
causing potential injury to the user. If you accidentally bend the Safety Spotters, please call our Customer
Service number (see the front cover) to order replacement Spotters.

WARNING: Always set both weight rests at the
same height. Always set both safety spotters at the
same height.

Locking
Clip

When you are not using the Curl Barbell (31), it can be
stored in the Barbell Posts (35).
ADJUSTING THE FOAM PADS
Bracket
The Foam Pads (10) on both the Leg Lever (18) and the
Front Leg (19) can be adjusted to two different positions.
To do this, pull one Foam Pad off the Pad Tube (38).
Move the Pad Tube to the other hole in the bracket on the
Front Leg or in the Leg Lever. Push the Foam Pad back
onto the Pad Tube.

10
19

ADJUSTING THE BACKREST
15

The Backrest (15) can be adjusted to a level position and
several decline and incline positions.
To increase the incline of the Backrest (15), simply pull up
on the Backrest until the tube on the Backrest Adjustment
Bracket (39) locks into the desired tab on the Bench
Frame (5). To decrease the incline, pull up slightly on the
Backrest, swing out the Backrest Adjustment Bracket and
then lower the Backrest until the Adjustment Bracket locks
into the desired tab on the Frame.

39
5
Adjustment
Tab
Tube

WARNING: Always make sure the tube on the backrest adjustment bracket is securely locked into one
of the adjustment tabs on the bench frame before
putting any weight on the backrest.

ATTACHING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (18), slide the desired amount of
weight onto the weight tube.

Weight Tube

WARNING: Do not place more than 150 pounds on
the leg lever. Always secure the weights with a
Weight Clip (13) when you have mounted them on
the leg lever, barbell or curl barbell.

SETTING UP THE BENCH FOR SQUAT EXERCISES
21
When performing squat exercises, place the Weight
Rests (21) into one of the upper sets of adjustment holes
in the two Uprights (1). Place the Safety Spotters (26) a
few holes lower, so they can catch the barbell, if you accidentally drop it.

1
1

21
26

WARNING: Always move the bench when you are
performing standing exercises in the cage. Stand
inside the area that is shaded in the drawing.

ATTACHING THE CURL POST
For some exercises, the Curl Post (42) must be attached
to the weight bench.
36
Insert the Curl Post (42) into the indicated hole in the
Front Leg (19). Align the holes in the Front Leg and the
Curl Post. Secure the Curl Post with the Adjustment Knob
(36). Make sure that you fully tighten the Adjustment
Knob.
WARNING: When the curl post is not in use, store it
away from the bench, so it will not interfere with
the next exercise you perform.

42
19

Exercise Guidelines
THE FOUR BASIC TYPES OF WORKOUTS

PERSONALIZING YOUR EXERCISE PROGRAM

Muscle Building

Specifying the exact length of time for each workout,
as well as the number of repetitions or sets for each
exercise, is a highly individual matter. It is very important to avoid overdoing it during the first few months
of your exercise program. You should progress at
your own pace and be sensitive to your bodyÕs signals. If you experience pain or dizziness at any time
while exercising, stop immediately and begin cooling
down. Find out what is wrong before continuing.
Remember that adequate rest and a proper diet are
important factors in any exercise program.

The only way to increase the size and strength of
your muscles is to push them close to their maximum
capacity. When you progressively increase the intensity of your exercise, your muscles will continually
adapt and grow. You can tailor the individual exercise
to the proper intensity level in two ways:
¥ by changing the amount of weight used
¥ by changing the number of repetitions or sets performed (A ÒrepetitionÓ is one complete cycle of an
exercise, such as one sit-up. A ÒsetÓ is a series of
repetitions).

WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.

The proper amount of weight for each exercise obviously depends upon the individual user. You must
gauge your limits and select the amount of weight that
is right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repetitions without difficulty, increase the amount of weight.

WORKING OUT
Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group
with emphasis on the areas that you want to develop
the most. To give balance and variety to your workouts, vary the exercises from session to session.

Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a moderate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.

Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.

Weight Loss

EXERCISE FORM

To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.

You will gain the greatest benefits from exercising by
maintaining proper form. This requires moving
through the full range of motion for each exercise and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise poster accompanying this manual, you will find photographs showing
the correct form for several exercises. A description of
each exercise is also provided, along with a list of the
muscles affected. Refer to the muscle chart on page
14 to find the locations of the muscles.

Cross Training
Many people desire a complete and well-balanced fitness program, and cross training is a very efficient
way to accomplish this. One example of a balanced
program is:
¥ Plan weight training workouts on Monday,
Wednesday and Friday.
¥ Plan 20 to 30 minutes of aerobic exercise, such as
cycling, running or swimming on Tuesday and
Thursday.
¥ Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of weight training and aerobic exercise will reshape and strengthen your body plus
develop your heart and lungs.

The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath!

You should rest for a short period of time after each
set. The ideal resting periods are:
¥ Rest three minutes after each set for a muscle building workout
¥ Rest one minute after each set for a toning workout
¥ Rest 30 seconds after each set for a weight loss
workout
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.

without strain. Stretching at the end of each workout
is very effective for increasing flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. The
chart on page 15 of this manual can be photocopied
and used to schedule and record your workouts. List
the date, the exercises performed, the weight plus the
numbers of sets and repetitions completed. Record
your weight and key body measurements at the end
of every month.

COOLING DOWN

Remember, the key to achieving the greatest results
is to make exercise a regular and enjoyable part of
your everyday life.

End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can

Muscle Chart

Trapezius
Deltoid

Pectoralis
Major

Biceps

Rectus
Abdominus

Brachioradials

Obliques

Trapezius
Deltoid
Rhomboideus
Triceps

Abductor

Latissimus Dorsi
Hip Flexors
Quadriceps

Spinae Erectors
Gluteus
Medius

Brachioradials

Adductor
Gluteus
Maximus
Soleus

Abductors
Hamstring

Gastrocnemius

EXERCISE

MONDAY

WEIGHT

SETS

REPS

WEIGHT

SETS

REPS

WEIGHT

SETS

REPS

Date:

AEROBIC EXERCISE

TUESDAY
Date:

WEDNESDAY

EXERCISE

Date:

THURSDAY

AEROBIC EXERCISE

Date:

/
EXERCISE

FRIDAY
Date:

Make photocopies of this page for scheduling and recording your workouts.

Part List - Model No. WEBE63990
Key No.

Qty.

Description

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

2
2
6
4
1
5
14
2
2
6
23
6
2
1
1
4
5
1
1
1
1
2
4
2
4
1
2
8

Upright
Base
M6 x 16mm Screw
M6 x 52mm Screw
Bench Frame
M10 Washer
M4 x 16mm Screw
Protector Strip
Stabilizer Endcap
Foam Pad
M10 Nylon Locknut
3/4Ó Round Inner cap
Weight Clip
Seat
Backrest
Support Plate
50mm Square Inner Cap
Leg Lever
Front Leg
Crossbar
Left Weight Rest
M10 x 193mm Bolt
Weight Clip Cover
51.8mm x 76.2mm Inner Cap
50mm Outer Cap
Left Safety Spotter
Backrest Tube
25.4 x 38.1mm Inner Cap

R0899A

Key No. Qty.
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
#
#

1
4
1
4
18
2
2
1
1
3
1
3
1
1
1
1
1
4
4
2
2
2
2
1
1
1
1

Description
Curl Pad
M6 Washer
Curl Barbell
1Ó Inner Cap
M10 x 68mm Bolt
M10 x 70mm Carriage Bolt
Barbell Post
Adjustment Knob
Stabilizer
Pad Tube
Backrest Adjustment Bracket
48mm Round Inner Cap
Bumper
Curl Post
M4 x 25mm Screw
M10 x 75mm Bolt
Olympic Barbell
2 3/4 lb Weight Plate
5 1/2 lb Weight Plate
11 lb Weight Plate
22 lb Weight Plate
33 lb Weight Plate
44 lb Weight Plate
Right Weight Rest
Right Safety Spotter
UserÕs Manual
Exercise Guide

Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the userÕs manual for information about ordering replacement parts.

Exploded Drawing - Model No. WEBE63990
R0899A

REMOVE THIS PART LIST/EXPLODED
DRAWING FROM THE MANUAL
SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE

13
45

23
51
50

Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give the following information when calling:
1. The MODEL NUMBER of the product (WEBE63990)
2. The NAME of the product (WEIDER¨ PRO PC3 Weight Bench)
3. The SERIAL NUMBER of the product (see the front cover of this manual)
4. The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING at the center of this manual).

Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which warranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
Part No. 157743 J01962-C R0899A

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 19
Create Date                     : 2000:01:12 14:00:04
Producer                        : Acrobat Distiller 3.02 for Power Macintosh
Author                          : Steve Slade
Creator                         : QuarkXPressª: PSPrinter 8.3.1
Title                           : *WEBE63990-157743

EXIF Metadata provided by EXIF.tools

Weider Pro Pc3 Bench Webe6399 Users Manual *WEBE63990 157743

Weider-Webe63990-Owner-S-Manual weider-webe63990-owner-s-manual

WEBE63990 to the manual 636faa18-f5fe-4bd9-b5f4-677c8ed79096

Navigation menu

Versions of this User Manual:

Views

Navigation