Weider Weccsy99400 Owner S Manual *WECCSY99400 167295(CEN)

Weider-Pro-9940-System-Weccsy9940-Users-Manual-733588 weider-pro-9940-system-weccsy9940-users-manual-733588

: Weider Weider-Weccsy99400-Owner-S-Manual weider-weccsy99400-owner-s-manual weider pdf

Open the PDF directly: View PDF .
Page Count: 35

Download
Open PDF In Browser	View PDF

®

Patent Pending

Model No. WECCSY99400
Serial No.

USER’S MANUAL

The serial number is found in the
location shown below. Write the
serial number in the space above.

Serial
Number
Decal

QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians on our customer hot line
will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:

1-888-936-4266

Mon.–Fri., 8 a.m.–6:30 p.m. EST
(excluding holidays)

CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual for future reference.

Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!

Table of Contents
Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cable Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Trouble-shooting and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Weight Resistance Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Ordering Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
One Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: A PART LIST/EXPLODED DRAWING and a PART IDENTIFICATION CHART are attached in the center of
this manual. Remove the PART LIST/EXPLODED DRAWING and the PART IDENTIFICATION CHART before
beginning assembly.

Important Precautions
WARNING:

To reduce the risk of serious injury, read the following important precautions before using the home gym.
1. It is the responsibility of the owner to ensure
that all users of the home gym are adequately informed of all precautions.

7. Always stand on a foot plate when performing an exercise that could cause the home
gym to tip.

2. Read all instructions in this manual and in
the accompanying literature before using the
home gym.

8. Keep hands and feet away from moving parts.
9. Keep children under the age of 12 and pets
away from the home gym at all times.

3. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.

10. Always wear athletic shoes for foot protection when exercising.

4. Use the home gym only on a level surface.
Cover the floor or carpet beneath the home
gym for protection.

11. Never release the press arms, butterfly arms,
leg lever, lat bar or ab strap while weights are
raised. The weights will fall with great force.

5. Inspect and tighten all parts often. Replace
any worn parts immediately.

12. Always disconnect the lat bar or ab strap
from the home gym when performing an
exercise that does not use the attachments.

6. Make sure the cables remain on the pulleys
at all times. If the cables bind while you are
exercising, stop immediately and make sure
the cables are on all of the pulleys.

13. The home gym is intended for home use only.
Do not use the home gym in a commercial,
rental or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.

2

Before You Begin
Thank you for selecting the innovative and versatile
WEIDER® PRO 9940 Home Gym. The WEIDER® PRO
9940 offers a unique selection of weight stations
designed to develop every major muscle group of the
body. Whether your goal is to tone your body, build
dramatic muscle size and strength or improve your
cardiovascular system, the WEIDER® PRO 9940
makes it easy to achieve the results you want.

HELPLINE at 1-888-936-4266, Monday through
Friday, 8 a.m. until 6:30 p.m. Eastern Time (excluding
holidays). To help us assist you, please note the product model number and serial number before calling.
The model number is WECCSY99400. The serial
number can be found on a decal attached to the WEIDER® PRO 9940 Home Gym (see the front cover of
this manual).

For your benefit, read this manual carefully before
using the WEIDER® PRO 9940 Home Gym. If you
have additional questions, please call our toll-free

Please use the drawing below to familiarize yourself with the major parts and how they fit together.

ASSEMBLED
DIMENSIONS:
Height: 77 in.
Width: 80 in.
Depth: 55 in.

Lat Bar

High Pulley
Station

Butterfly
Arms
Ab Pulley
Station

Backrest

Backrest

Press Arms

Curl Pad
Leg Press
Plate
Foam Pads
Seat

Leg
Lever

Low Pulley
Station

Weight
Stacks

Foot Plate

3

Leg Press
Lever

Assembly
Note: This introduction will save you more time
than it takes to read it!

Identifying Parts
To help you identify the small parts used in assembly, we have included a PART IDENTIFICATION
CHART located in the center of this manual. Place
the chart on the floor or work table and use it to
quickly identify different parts as you open the packages for each step. Note: Some small parts may
have been pre-attached for shipping. If a part is not
in the parts bag, check to see if it has been preattached.

Making Things Easier for Yourself
Everything in this manual is designed to ensure
that our products can be assembled successfully
by anyone. However, it is important to realize
that your new equipment is a sophisticated product with many small parts. The assembly process
will take time—possibly several hours. Most people find that by setting aside plenty of time, and
by deciding to make the task enjoyable, assembly will go smoothly. You may want to complete
the process over a couple of evenings.

Orienting Parts
As you assemble this product, be sure that all parts
are oriented as shown in the drawings.

Some assembly steps require two people.

Tightening Parts
Tighten all parts as you assemble them, unless
instructed to do otherwise.

Giving Yourself a Good Start
Before you begin the assembly process itself, take
the time to complete the steps outlined here.

Lining Up the Tools
Assembly requires the following tools (not included):
• Two (2) adjustable wrenches

Clearing the Workspace
Clear a workspace that is large enough to hold all
parts and allow you to walk all the way around the
assembled equipment.

• One (1) standard screwdriver
• One (1) phillips screwdriver

Unpacking the Box
To make the assembly process as smooth as possible, we have broken it into separate stages. All parts
used in each stage are found in individual packages
in the shipping box. Place all parts in a cleared area
and remove the packing materials. Do not dispose of
the packing materials until assembly is completed.

• One (1) rubber mallet
• Lubricant, such as grease or petroleum jelly,
and soapy water
• Tape, such as clear tape or masking tape
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end wrenches
or a set of ratchet wrenches.

Important: Wait until you begin each assembly
stage to open the parts bag labeled for that
assembly stage.

The Four Stages of the Assembly Process
Frame Assembly
You will begin by assembling the base and the
upright frames that serve as the skeleton of the
equipment.

Cable Assembly
This assembly completes the cables and pulleys
that connect the moving arms with each other and
with the weights.

Arm Assembly
This assembly completes the press and butterfly
arms that you operate while you are exercising.

Seat Assembly
This assembly completes the seat and backrest
that support your body while you are exercising.

4

1a

Frame Assembly

28

1. Before beginning, make sure that you have read
and understood the information on page 4.

28
4

Locate and open the parts bag labeled “FRAME
ASSEMBLY.”

28
95
92

See drawing 1a. Press a 2” Square Inner Cap (28)
into each end of the Butterfly Base (4). Press two 2”
Square Inner Caps (28) into the Weight Base (5).
Insert four 5/16” x 2 1/2” Carriage Bolts (92) up
through the indicated holes in the Butterfly Base (4).
Insert a 3/8” x 3 1/2” Carriage Bolt (95) up through
the hole at the end of the Butterfly Base. Note: If the
Bolts fall out, secure them by putting a small
piece of tape over the head of each Bolt. Place the
Butterfly Base flat on the floor.

28

1b

89

93

See drawing 1b. Attach the Weight Base (5) to the
Butterfly Base (4) with two 5/16” x 2 3/4” Bolts (89), a
Support Plate with 3 1/2” center holes (93), and two
5/16” Nylon Locknuts (64). Do not tighten the Nylon
Locknuts yet.
Note: There are three kinds of Support Plates. The
main difference between them is the distance
between the holes. When you need a Support
Plate, find the type with holes that will fit over the
Bolts you are using.

5

92

64

64

4

5

2a

5

24
63

2. See drawing 2a. Press a 2” Square Inner Cap (28)
into the end of the Press Base (6).

57

Attach a 3 1/2” Pulley (24) to each of the brackets on
the Weight Base (5) with a 3/8” x 1 3/4” Bolt (57) and
a 3/8” Nylon Jamnut (63).

63
28

57
6
102

Insert four 5/16” x 2 1/2” Carriage Bolts (92) up
through the indicated holes in the Press Base (6).
Insert a 3/8” x 2 1/2” Carriage Bolt (101) and a 3/8 x
4” Carriage Bolt (102) up through the indicated holes
at the end of the Press Base (6).
See drawing 2b. Attach the Press Base (6) to the
Weight Base (5) with two 5/16” x 2 3/4” Bolts (89), a
Support Plate with 3 1/2” center holes (93), and two
5/16” Nylon Locknuts (64). Do not tighten the Nylon
Locknuts yet.

92 101
92
2b

64
5
64

93

6
89

5

3. Place the bracket on the lower end of the Butterfly
Upright (1) over the indicated 5/16” x 2 1/2” Carriage
Bolts (92) in the Butterfly Base (4). Hand tighten two
5/16” Nylon Locknuts (64) onto the Bolts. Do not
tighten the Nylon Locknuts yet.

3

1

64

4
92
4. Press three 2” Square Inner Caps (28) into the
Butterfly Top Frame (33). Press two 1” Round Inner
Cap (86) into the top of the Butterfly Top Frame (33).

4

89
93

86

28

28

Attach the Butterfly Top Frame (33) to the indicated
bracket at the top of the Butterfly Upright (1) with two
5/16” x 2 3/4” Bolts (89), a Support Plate with 3 1/2”
center holes (93), and two 5/16” Nylon Locknuts (64).

33
64

28

1
5. Attach the Butterfly Seat Frame (14) to the Front Leg
(20) with two 5/16” x 2 3/4” Bolts (89), two 5/16”
Washers (36), and two 5/16” Nylon Locknuts (64). Do
not tighten the Nylon Locknuts yet.

5

64

Attach the Butterfly Seat Frame (14) to the Butterfly
Upright (1) with two 5/16” x 2 3/4” Bolts (89), two
5/16” Washers (36) and two 5/16” Nylon Locknuts
(64). Do not tighten the Nylon Locknuts yet.

6

1
89

36
Slide the bracket on the Front Leg (20) onto the two
5/16” x 2 1/2” Carriage Bolts (92) in the Butterfly Base
(4). Hand tighten two 5/16” Nylon Locknuts (64) onto
the Bolts. Do not tighten the Nylon Locknuts yet.

64

14

64
36

64
64

89
20

4
92

6. Press a 2” Square Inner Cap (28) half way into the
top of the Front Leg (20). Press a 2” Square Inner
Cap (28) into each end of the Small Leg Lever (41).

6

63

28

28

Attach the Bumper (40) to the indicated hole in the
Front Leg (20) with a 1” Tap Screw (80).

62
40

41

Lubricate the 3/8” x 3 1/4” Bolt (62). Attach the Small
Leg Lever (41) to the bracket on the Front Leg (20)
with the Bolt and a 3/8” Nylon Jamnut (63). Do not
overtighten the Nylon Jamnut; it must be easy to
pivot the Leg Lever.

20
80
Lubricate

28

7. Press a 1” Square Inner Cap (98) into the small tube
on the Press Upright (2).

7
64

Place the bracket on the lower end of the Press
Upright (2) over the indicated 5/16” x 2 1/2” Carriage
Bolts (92) in the Press Base (6). Hand tighten two
5/16” Nylon Locknuts (64) onto the Bolts. Do not
tighten the Nylon Locknuts yet.

92

Place the bracket on the lower end of the Support
Frame (3) over the indicated 3/8” x 2 1/2” Carriage
Bolt (101) and the 3/8” x 4” Carriage Bolt (102) in the
Press Base (6). Hand tighten a 3/8” Nylon Jamnut
(63) onto the 3/8” x 2 1/2” Carriage Bolt (101). Do not
tighten the Nylon Jamnut yet.

64

3

2
98

Note: Do not thread a Jamnut onto the 3/8” x 4”
Carriage Bolt (102) yet.

63

Attach the Support Frame (3) to the Press Upright (2)
with two 5/16” x 2 1/2” Carriage Bolts (92) and two
5/16” Nylon Locknuts (64). Do not tighten the Nylon
Locknuts yet.

64

102
101

6
92
8. Press a 2” Square Inner Cap (28) into the Press Top
Frame (9).

8

89
28

Attach the Press Top Frame (9) to the indicated
bracket at the top of the Press Upright (2) with two
5/16” x 2 3/4” Bolts (89), a Support Plate with 3 1/2”
center holes (93), and two 5/16” Nylon Locknuts (64).

93
9

2
64

7

9. Press a 2” Square Inner Cap (28) into the Press Seat
Frame (7).
Slide the bracket on the Press Seat Frame (7) onto
the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the
Press Base (6). Hand tighten two 5/16” Nylon
Locknuts (64) onto the Bolts. Do not tighten the
Nylon Locknuts yet.
Attach the Press Seat Frame (7) to the Press Upright
(2) with two 5/16” x 2 3/4” Bolts (89), two 5/16”
Washers (36), and two 5/16” Nylon Locknuts (64). Do
not tighten the Nylon Locknuts yet.

10. Lubricate the 3/8” x 3” Bolt (88). Attach the Leg Press
Lever (83) to the Press Base (6) with the Bolt and a
3/8” Nylon Locknut (50). Do not overtighten the
Nylon Locknut; the Leg Press Lever must pivot
easily.

9

89

36
64

7
36
28
89
64

2

64
6
92

10

83

6
50

Lubricate
88

11. Place two Weight Bumpers (51) over the indicated
holes in the Weight Base (5). Slide a Weight Guide
(15) into each of the holes.

11

Attach the indicated Weight Guide (15) to the Weight
Base (5) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat
Washers (48), and a 3/8” Nylon Locknut (50).

15
16
Groove
Pin

Slide six Weights (21) onto the Weight Guides (15).
Make sure the Weights are turned so the pin
grooves point towards the floor.

17

Press a Weight Tube Bumper (18) into the lower end
of the Short Weight Tube (17). Slide the Weight Tube
into the center holes in the Weights (21).

18
21
Pin
Grooves

Slide a Top Weight (16) onto the Weight Guides (15).
Note: Make sure the Top Weight is turned so the
groove fits over the welded pin on the Weight
Tube (17).

51
48
50
5

46

8

48

12. Place two Weight Bumpers (51) over the indicated
holes in the Weight Base (5). Slide a Weight Guide
(15) into each of the holes.

12

15

Attach the indicated Weight Guide (15) to the Weight
Base (5) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat
Washers (48), and a 3/8” Nylon Locknut (50).

16
Groove

Slide ten Weights (21) onto the Weight Guides (15).
Make sure the Weights are turned so the pin
grooves point towards the floor.
Press a Weight Tube Bumper (18) into the lower end
of the Long Weight Tube (70). Slide the Weight Tube
into the center holes in the Weights (21).

Pin
70
18
21

Pin
Grooves

Slide a Top Weight (16) onto the Weight Guides (15).
Note: Make sure the Top Weight is turned so the
groove fits over the welded pin on the Weight
Tube (70).
51

51
48

50

48
46
13. Place the Weight Top Frame (66) on the indicated
brackets on the Uprights (1 and 2). Note: The four
Weight Guides (15) must be behind the Weight
Top Frame, as shown in step 14.

5

46

13
34

Attach the Weight Top Frame (66) to the Butterfly Top
Frame (33) with two 3/8” x 2 3/4” Bolts (46), a
Support Plate with 4” center holes (94), and two 3/8”
Nylon Locknuts (50). Do not tighten the Nylon
Locknuts yet.

46

50
66

94
50

Attach the Weight Top Frame (66) to the bracket on
the Butterfly Upright (1) with two 3/8” x 2 3/4” Bolts
(46), a Support Plate with 2 1/2” center holes (34),
and two 3/8” Nylon Locknuts (50). Do not tighten the
Nylon Locknuts yet.
14. Attach the Weight Top Frame (66) to the Press Top
Frame (9) with one 3/8” x 2 3/4” Bolt (46), a Support
Plate with 4” center holes (94), and a 3/8” Nylon
Locknut (50). Slide a 3 1/2” Pulley (24) with a Cable
Trap (25) onto a 3/8” x 4” Bolt (78). Insert the Bolt
through the Support Plate (94) and hand tighten a
3/8” Nylon Locknut (50) onto it.
Attach the Weight Top Frame (66) to the bracket on
the Press Upright (2) with two 3/8” x 2 3/4” Bolts (46),
a Support Plate with 2 1/2” center holes (34) and two
3/8” Nylon Locknuts (50). Do not tighten the Nylon
Locknuts yet.

9

33

15
1

Brackets

14

46
34

66

50
50
94

9

46
25
24
2

78

15. Attach each of the four Weight Guides (15) to the
Weight Top Frame (66) with a 3/8” x 3 3/4” Bolt (59),
a 3/8” Flat Washer (48), and a 3/8” Nylon Locknut
(50).

15

48

50
50

48

Important: Go back and fully tighten all Nylon
Locknuts used in steps 1 through 15.

59
59
15
15

16

Arm Assembly
16. Locate and open the parts bag labeled “ARM
ASSEMBLY.”

8

Press a Plastic Bushing (100) onto each welded tube
on the Press Frame (8).

6

50

Lubricate

Lubricate the 3/8” x 8” Bolt (52). Attach the Press
Frame (8) to the welded tubes on the Press Base (6)
with the Bolt and a 3/8” Nylon Locknut (50). Do not
overtighten the Nylon Locknut; it must be easy to
pivot the Press Frame.
17. Press a 1 3/4” Square Inner Cap (35) into the top of a
Press Arm (77). Press a 1” Round Inner Cap (76) into
the indicated hole in the Press Arm.

100

Welded
Tube

52

17

Attach the Press Arm (77) to the bracket on the Press
Frame (8) with two 5/16” x 2 1/2” Bolts (87) and two
5/16” Nylon Locknuts (64).
Repeat this step to assemble the second Press Arm
(77, not shown).

35

76

64

8

87
77

10

18. Press a 1 3/4” Square Inner Cap (35) into each end
of the Right Butterfly Arm (11). Wet the lower end of
the Arm with soapy water. Slide a Butterfly Foam Pad
(29) onto the lower end of the Arm.

18
33
Axle
11

Lubricate the indicated axle on the Butterfly Top
Frame (33). Orient the Right Butterfly Arm (11) as
shown and slide it onto the axle. Secure the Butterfly
Arm with two Retainer Rings (31) and a 1” Round
Outer Cap (38). Note: Place the Retainer Rings on
top of the inverted Outer Cap and gently tap the
Cap onto the axle with a hammer. Make sure the
teeth on the Retainer Rings bend towards the Cap
as shown in the inset drawing.

35
31
38

Repeat this step to assemble the Left Butterfly Arm
(10, not shown).

35

29

Axle
31
Teeth
38

Cable Assembly
19. Locate and open the parts bag labeled “CABLE
ASSEMBLY.” For Cable identification and routing
during steps 19 to 49, refer to the Cable Diagrams
and Cable ID Chart on pages 23 and 24.

19

84
Bracket

Identify the Butterfly Cable (73). It is approximately
52” long and it has a closed loop on each end. Attach
the Butterfly Cable to the bracket on the Left Butterfly
Arm (10) with a 3/8” x 1” Bolt (84) and two 3/8” Nylon
Jamnuts (63). Note: The loop on the Cable and the
two Nylon Jamnuts must be mounted underneath
the welded bracket.

63

10
73

20. Open the bag marked Pulley Bag 2 and remove one
“V”-Pulley (27). Keep the rest of the pulleys in the bag
for future identification.

20

32
27
53

Wrap the Butterfly Cable (73) around a “V”-Pulley
(27) in the direction shown. Attach the “V”-Pulley and
a Large Cable Trap (32) to the bracket on the back
of the Butterfly Upright (1) with a 3/8” x 2 1/2” Bolt
(53) and a 3/8” Nylon Locknut (50). Make sure the
Large Cable Trap is oriented as shown.

50
Bracket

1

11

73

21. Remove both 3 1/2” Pulleys (24) from the pre-assembled Small Pulley Bracket (22).

21

Wrap the Butterfly Cable (73) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley to the
Small Pulley Bracket (22) with a 3/8” x 1 3/4” Bolt
(57) and a 3/8” Nylon Locknut (50). Make sure the
Small Pulley Bracket is oriented exactly as
shown.

73

24
50
57
22

22. Wrap the Butterfly Cable (73) around a “V”-Pulley
(27) in the direction shown. Attach the “V”-Pulley and
a Large Cable Trap (32) to the bracket on the back
of the Butterfly Upright (1) with a 3/8” x 2 1/2” Bolt
(53) and a 3/8” Nylon Locknut (50). Make sure the
Large Cable Trap is oriented as shown.

22
Bracket

53

50
27
73

32

1
23. Attach the Butterfly Cable (73) to the bracket on the
Right Butterfly Arm (11) with a 3/8” x 1” Bolt (84) and
two 3/8” Nylon Jamnuts (63). Note: The loop on the
Cable and the two Nylon Jamnuts must be mounted underneath the welded bracket.

23
84

63

11

24. Identify the Ab Cable (74). It is approximately 224”
long, and it has a ball on one end and a threaded
shaft on the other. You will start by attaching the end
of the Cable with the ball.
Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in
the direction shown. Place two Pulley Covers (47)
over the Pulley, so that the slots in the Pulley Covers
are placed over the Cable. Attach the Pulley and
Pulley Covers to the indicated hole in the Butterfly
Upright (1) with a 3/8” x 3 3/4” Bolt (59), two 3/8” Flat
Washers (48), and a 3/8” Nylon Jamnut (63). Make
sure the Cable is between the Pulley and the
welded pin on the Upright.

12

Bracket

73

24
59

48
47

Pin
74

24

63
48

1

25. Remove both 3 1/2” Pulleys (24) from the pre-assembled Adjustable Pulley Plates (23).
Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in
the direction shown. Attach the Pulley and a Cable
Trap (25) to the top hole in the two Adjustable Pulley
Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon
Locknut (50). Make sure the Cable Trap and the
Pulley Plates are oriented as shown.

25
25
50

24
54
23
74

26. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in
the direction shown. Attach the Pulley to the Small
Pulley Bracket (22) with a 3/8” x 1 3/4” Bolt (57) and
a 3/8” Nylon Locknut (50). Make sure the Pulley
Bracket is oriented as shown.

26
50
22

57

24

74
27. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in
the direction shown. Attach the Pulley and a Cable
Trap (25) to the welded bracket on the Butterfly Base
(4) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut
(50). Make sure the Cable Trap is oriented as
shown.

27

74
54

24

25

4
50

13

28. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in
the direction shown. Slide the Pulley and a Cable
Trap (25) onto the 3/8” x 3 1/2” Carriage Bolt (95)
already inserted into the Butterfly Base (4). Secure
the Pulley with a 3/8” Nylon Jamnut (63). Make sure
the Cable Trap is oriented as shown.
Route the threaded end of the Ab Cable (74) under
the 3 1/2” Pulley (24) that is already mounted on the
Weight Base (5). Make sure the Cable is routed in
the direction shown.

28

63
74

24
25
24

95

4

5

Note: For clarity, this and the following drawings
show some parts removed.
29. Wrap the Ab Cable (74) around a 4 1/2” Pulley (82) in
the direction shown. Attach the Pulley inside the indicated bracket on the Weight Top Frame (66) with a
3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50).
Make sure the threaded end of the Ab Cable is
routed through the bracket, as shown.

29

50

Bracket

82
57
66

74
End of
Cable

30. Attach the threaded end of the Ab Cable (74) to a “U”Bracket (97) with a 1/4” Flat Washer (71) and a 1/4”
Nylon Locknut (68).

30
74

Attach the “U”-Bracket (97) to the hole in the Short
Weight Tube (17) with a 5/16” x 1 3/4” Bolt (96) and a
5/16” Nylon Locknut (64). Note: Do not completely
tighten the Nylon Locknut; it should be threaded
only two turns onto the end of the Cable, as
shown in the inset drawing.

71
68
97

74
64
97
96

71
68

17

14

31. Remove a Pro Pulley (26) from the bag marked
Pulley Bag 2.

31

Identify the Low Pulley Cable (75). It is approximately
143 1/2” long and it has a ball on one end and a loop
on the other. Route the end with the loop through the
slot in the cable guide on the Butterfly Base (4).
Route the Low Pulley Cable (75) under a Pro Pulley
(26) as shown. Attach the Pro Pulley and a Cable
Trap (25) to the bracket on the Butterfly Base (4) with
a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
Make sure the Cable Trap is oriented as shown.

32. Wrap the Low Pulley Cable (75) around a 3 1/2”
Pulley (24) in the direction shown. Attach the Pulley
and a Cable Trap (25) to the indicated hole in the
Butterfly Upright (1) with a 3/8” x 4 3/4” Bolt (60) and
a 3/8” Nylon Jamnut (63). Note: Thread the Jamnut
only two turns onto the Bolt, since you will later
attach another Pulley to the Bolt. Make sure the
Cable Trap is oriented as shown.

54

26

25

4

Cable
Guide
50

75
32

60
1

24
25
63
75

33. Wrap the Low Pulley Cable (75) over a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to the lower hole in the Adjustable
Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8”
Nylon Locknut (50). Make sure the Cable Trap is
oriented as shown.

33
23
50
54
25
24

75

34. Remove the 3/8” Nylon Jamnut (63) from the
3/8” x 4 3/4” Bolt (60) inserted into the Butterfly
Upright (1) in step 32.

34
1
75

Wrap the Low Pulley Cable (75) around a 3 1/2”
Pulley (24) in the direction shown. Attach the Pulley
and a Cable Trap (25) to the 3/8” x 4 3/4” Bolt (60)
with the 3/8” Nylon Jamnut (63). Make sure the
Cable Trap is oriented as shown.

25
60

24

15

63

35. Attach the loop on the end of the Low Pulley Cable
(75) to the indicated hole in the Small Leg Lever (41)
with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat Washers
(48), and a 3/8” Nylon Jamnut (63).

35
41
63

48

75

48

36. Remove a Pro Pulley (26) from the bag marked
Pulley Bag 2.

46

36
9

Identify the Press Cable (72). It is approximately 389
1/2” long with a ball on one end and a threaded shaft
on the other. Begin by attaching the end with the ball.

63

Wrap the Press Cable (72) around a Pro Pulley (26)
in the direction shown. Attach the Pulley to the indicated hole in the Press Top Frame (9) with a 3/8” x
3 1/2” Bolt (56), a 3/8” Flat Washer (48), and a 3/8”
Nylon Jamnut (63). Make sure the Cable is between
the Pulley and the welded pin on the Press Top
Frame.
37. Route the threaded end of the Press Cable (72)
around the 3 1/2” Pulley (24) that is already mounted
on the Top Frame (9).

26

48

72

Pin

56

37

9
24

72

38. Wrap the Press Cable (72) around a 3 1/2” Pulley (24)
in the direction shown. Attach the Pulley to the indicated hole in the Press Upright (2) with a 3/8” x 3 3/4”
Bolt (59), a 3/8” Flat Washer (48) and a 3/8” Nylon
Locknut (50). Make sure the Cable Trap is oriented
as shown.

38

2

50
48
25

24
72
59

16

39. Important: Although the following steps are not
difficult to perform, the correct routing of the
cable is critical to the functioning of the home
gym. Please make sure that you wrap the cable
around the pulleys exactly as shown in each step.

39

50

Route the Press Cable (72) through the opening in
the Press Frame (8), and wrap the Cable around a
3 1/2” Pulley (24) in the direction shown. Route the
end of the Cable back through the opening in the
Press Frame.
Attach the Pulley (24) to the indicated hole in the
Press Frame (8) with a 3/8” x 3 1/4” Bolt (62), a 3/8”
Flat Washer (48) and a 3/8” Nylon Locknut (50).
Make sure the Pulley is mounted on the inside of
the Press Frame. Make sure the Cable Trap is oriented as shown.

72
48

24

Attach the Pulley (24) to the indicated hole in the
Press Frame (8) with a 3/8” x 3 1/4” Bolt (62), a 3/8”
Flat Washer (48), and a 3/8” Nylon Locknut (50).
Make sure the Pulley is mounted on the inside of
the Press Frame. Make sure the Cable Trap is oriented as shown.

8

25

40

50
48

2

40. Wrap the Press Cable (72) around a “V”-Pulley (27) in
the direction shown. Attach the “V”-Pulley and a Large
Cable Trap (32) to the small tube on the Press
Upright (2) with a 3/8” x 3 1/4” Bolt (62), a 3/8” Flat
Washer (48) and a 3/8” Nylon Locknut (50). Note:
The small tube has four adjustment holes. Mount
the “V”-Pulley in the hole farthest from the
Upright. Make sure the Cable Trap is oriented as
shown.
41. Route the Press Cable (72) back through the opening
in the Press Frame (8) and wrap the Press Cable
around a 3 1/2” Pulley (24) in the direction shown.
Then, route the Press Cable back through the opening in the Press Frame (8).

62

Small tube,
last hole

32

27
72
62

41

62

48
72
25

8

24
42. Wrap the Press Cable (72) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to the indicated hole on the far side
of the Press Upright (2) with a 3/8” x 4 3/4” Bolt (60)
and a 3/8” Nylon Jamnut (63). Note: Thread the
Jamnut only two turns onto the Bolt; you will later
attach another Pulley to the Bolt. Make sure the
Cable Trap is oriented as shown.
Route the Press Cable (72) back through the opening
in the Press Frame (8), so the end is in front of the
Press Frame.

17

50

42

60

72

24

25

2
63

43. Wrap the Press Cable (72) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to the indicated hole on the far side
of the Leg Press Lever (83) with a 3/8” x 4 3/4” Bolt
(60) and a 3/8” Nylon Jamnut (63). Note: Thread the
Jamnut only two turns onto the Bolt; you will later
attach another Pulley to the Bolt. Make sure the
Cable Trap is oriented as shown.

43
72
60
24
25

63

83

44. Wrap the Press Cable (72) around a “V”-Pulley (27)
in the direction shown. Attach the “V”-Pulley and a
Large Cable Trap (32) underneath the Press Seat
Frame (7) with a 3/8” x 4 1/4” Bolt (85), a 3/8” Flat
Washer (48), and a 3/8” Nylon Locknut (50). Note:
the Press Seat Frame has five adjustment holes.
Mount the “V”-Pulley in the hole closest to the
Leg Press Lever. Make sure the Cable Trap is oriented as shown.

44

85

48

7

32

27

72
50
45. Wrap the Press Cable (72) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to the near side of the Leg Press
Lever (83). Use the 3/8” x 4 3/4” Bolt (60) that was
inserted in step 43 and secure the Pulley with the
3/8” Nylon Jamnut (63). Make sure the Cable Trap
is oriented as shown.

45

83
24
60
8

25
63

46. Wrap the Press Cable (72) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to near side of the Press Upright (2).
Use the 3/8” x 4 3/4” Bolt (60) that was inserted in
step 42 and secure the Pulley with the 3/8” Nylon
Jamnut (63). Make sure the Cable Trap is oriented
as shown.

72

46

50
24
25

2

102
Wrap the Press Cable (72) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to the 3/8” x 4” Carriage Bolt (102)
that was inserted into the Press Base (6) earlier.
Secure the Pulley with the 3/8” Nylon Locknut (50).
Make sure the Cable Trap is oriented as shown.

18

25
60

24

72
63

47. Route the threaded end of the Press Cable (72)
around the 3 1/2” Pulley (24) that was mounted on the
bracket on the Weight Base (5) in an earlier step.

47

72
24
5

48. Wrap the Press Cable (72) over a 4 1/2” Pulley (82)
in the direction shown. Attach the Pulley inside the
indicated bracket on the Weight Top Frame (66) with
a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut
(50). Make sure the end of the Cable is routed
through the bracket, as shown.

48
50

82

72
57
66

49. Attach the threaded end of the Press Cable (72) to
the remaining “U”-Bracket (97) with a 1/4” Flat
Washer (71) and a 1/4” Nylon Locknut (68).

49
72

Attach the “U”-Bracket (97) to the hole in the Long
Weight Tube (70) with a 5/16” x 1 3/4” Bolt (96) and a
5/16” Nylon Locknut (64). Note: Do not completely
tighten the Nylon Locknut; it should be threaded
only two turns onto the end of the Cable, as
shown in the inset drawing.

72
68
97

Important: Follow all four cables from end to end
and make sure that they rest in the grooves of all
pulleys and that the cables and the pulleys move
smoothly.

72
64
97
96
70

19

71
68

50

Seat Assembly
50. Locate and open the parts bag labeled “SEAT
ASSEMBLY.”

1

Attach the Backrest (12) to the indicated holes in the
Butterfly Upright (1) with two 1/4” x 2 1/2” Bolts (79)
and two 1/4” Flat Washers (71).

79
12
71

79

51. Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the
center hole in a Seat Plate (65). Attach the Seat Plate
to the Press Backrest (99) with two 1/4” x 3/4” Bolts
(49).
Insert the 1/4” x 2 1/2” Carriage Bolt (45) into the
indicated hole in the Butterfly Upright (2) and secure
it with a 1/4” Flat Washer (71) and a 1/4” Nylon
Locknut (68). Secure the other end of the Press
Backrest (99) with a 1/4” x 2 1/2” Bolt (79) and a 1/4”
Flat Washer (71).

51
2

79

71
99
65

49

68

71
45

20

52. Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the
center hole in a Seat Plate (65). Attach the Seat Plate
to a Seat (13) with two 1/4” x 3/4” Bolts (49).

52

Insert the 1/4” x 2 1/2” Carriage Bolt (45) into the indicated hole in the Butterfly Seat Frame (14) and
secure it with a 1/4” Flat Washer (71) and a 1/4”
Nylon Locknut (68). Secure the other end of the Seat
(13) with a 1/4” x 2 1/2” Bolt (79) and a 1/4” Flat
Washer (71).

45

13
65
14

71

Attach the other Seat (13) to the Press Seat Frame
(7, not shown) in the same manner.

68
71
53

Miscellaneous Assembly
53. Press 3/4” Round Inner Caps (43) into the ends of the
Pad Tube (42) and the indicated tube on the Front
Leg (20).

49

43

30

79

Tube
30

41
43

Insert the Pad Tube (42) into the indicated hole in the
Small Leg Lever (41). Slide Foam Pads (30) onto the
ends of the Pad Tube and the tube on the Leg Lever.

43

30
20

43

42
30
54. Press a 1 3/4” Square Inner Cap (35) into the indicated end of the Adjustment Tube (90).

54

91

Attach the Adjustment Tube (90) to the bracket (not
visible in the drawing) on the back of the Leg Press
Plate (55) with a 5/16” x 2 1/2” Bolt (87), two 5/16”
Washers (36), and a 5/16” Nylon Locknut (64).

64

36
90

Attach the Leg Press Plate (55) to the Leg Press
Lever (83) by placing the Adjustment Tube (90) into
the bracket on top of the Leg Press Lever and securing it with the Lock Pin (91). Note: The lip on the
Leg Press Plate must be on the upper edge.

55. Attach the Curl Pad (105) to the Curl Post (104) with
two 1/4” x 3/4” Bolts (49).

35

36

87

55
83

55

105
49

104

21

56. Apply the WEIDER PRO 9940 decal in the location shown. Important: The warning decals shown below
have been attached to the home gym in the locations shown. If a decal is missing or illegible, please
call our customer hotline at the number on the front cover of this manual to order a replacement
decal. Apply the new decal in the appropriate location.
56

WEIDER
PRO 9940

57. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in
ADJUSTMENT, beginning on page 25 of this manual.
Before using the home gym, pull each cable a few times to make sure that the cables move smoothly over
the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the
cables are not properly installed, they may be damaged when heavy weight is used. If there is any
slack in the cables, you will need to remove the slack by tightening the cables. See TROUBLESHOOTING AND MAINTENANCE on page 26.

22

Cable Diagrams
The Cable Diagrams below and on the next page show the proper routing of the Butterfly Cable (73), the Ab
Cable (74), the Low Pulley Cable (75) and the Press Cable (72). The numbers show the correct route for each
Cable. Make sure that the Cables are routed correctly, that the Pulleys move smoothly, and that the
Cable Traps do not touch or bind the Cables. Incorrect cable routing can damage the home gym.
Ab Cable (74)

Low Pulley Cable (75)

7

3
3

1

2

2
1

4

5

8
5
4

Butterfly Cable (73)
6
4
1
5
2
Cable ID Chart

73, 52”
75, 143.5”

3

74, 224”
72, 389.5”

23

Press Cable (72)

14

2

1

15

13

5

6

12

9

8

4

3

10
7

24

11

Adjustment
The instructions below describe how each part of the home gym can be adjusted. Refer to the exercise poster
accompanying this manual to see how the home gym should be set up for each exercise. IMPORTANT: When
using an attachment, make sure it is in the correct starting position for the exercise to be performed. If
there is any slack in the cables or chain as an exercise is performed, the effectiveness of the exercise
will be reduced.
Changing the Weight Setting

19

To change the setting of the weight stack, insert a Weight
Pin (19) under the desired Weight (21). Make sure you
insert the Weight Pin as far as it will go. Note: Due to the
cables and pulleys, the amount of resistance at each
exercise station may vary from the weight setting.
Use the WEIGHT RESISTANCE CHART on page 27 to
find the approximate amount of resistance at each
weight station.

21

Attaching the Lat Bar, Nylon Strap or Ab Strap to the
Low Pulley Station

75
58

Attach the Lat Bar (61) to the Low Pulley Cable (75) with
a Cable Clip (69). For some exercises, the Chain (67)
should be attached between the Lat Bar and the Low
Pulley Cable with two Cable Clips. Adjust the length of
the Chain between the Lat Bar and the Low Pulley
Cable so the Lat Bar is in the correct starting position
for the exercise to be performed.

67
69
69
81

61
The Nylon Strap (58) or Ab Strap (81) can be attached in
the same manner.
Attaching the Lat Bar, Nylon Strap or Ab Strap to the
High Pulley Station
Attach the Lat Bar (61) to the Press Cable (72) with a
Cable Clip (69). For some exercises, the Chain (67)
should be attached between the Lat Bar and the High
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the High Cable so the
Lat Bar is in the correct starting position for the exercise to be performed.

69
58
72

67
61

69
81

The Nylon Strap (58) or Ab Strap (81) can be attached in
the same manner.
91
Adjusting the Leg Press Plate
To adjust the position of the Leg Press Plate (55), pull out
the Lock Pin (91) and slide the Adjustment Tube (90)
backwards or forwards in the bracket on the Leg Press
Lever (83). Line up one of the adjustment holes in the
Adjustment Tube with the hole in the bracket and re-insert
the Lock Pin.

25

90

83
55

To use the Curl Pad (105), remove the 2” Square Inner
Cap (28) from the Front Leg (20) and insert the Curl Post
(104) into the Front Leg. Secure the Curl Pad by inserting
the Adjustment Knob (103) at the desired height.

105

104
28
103
20

Trouble-shooting and Maintenance
Inspect and tighten all parts each time you use the home gym. Replace any worn parts immediately. The
home gym can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
Tightening the Cables
If a cable slips off the pulleys often, the cable may have become twisted. Remove the cable and re-install
it. If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.
The type of cable used on the home gym can stretch slightly when it is first used. If there is slack in the cables
before resistance is felt, the cables should be tightened. Slack can be removed from the cables in several different ways:
The Adjustable Pulley Plates (23) have several sets of
adjustment holes. By moving one or both pulleys (24) to
a different set of holes, you will tighten the cables.
23
To move a Pulley (24), remove the 3/8” Nylon Locknut
(50) and the 3/8” x 2” Bolt (54). Remove the Cable Trap
(25) and Pulley from the Adjustable Pulley Plates (23).
Re-attach the Pulley and Cable Trap to the appropriate
adjustment hole in the Pulley Plates. Note: Begin by
moving one Pulley to the second adjustment hole. If
the cables are still too loose, move the same Pulley
to the third hole. If additional adjustment is needed,
move the other Pulley until the cables are tight.

Adjustment
Holes

54

50
25

24

Slack can be removed form the Press Cable (72) by
moving one or both of the “V”-Pulleys (27) on the Press
Cable.
One “V”-Pulley (27) is attached to the small tube on the
Press Upright (2). There are three free holes in the small
tube, and you can move the “V”-Pulley to any one of
them to tighten the cables. Start by moving the “V”Pulley one hole, and then one more, as needed.

2

7
72

The second “V”-Pulley (27) is attached to the Press Seat
Frame (7). There are five adjustment holes in the Seat
Frame. By moving the “V”-Pulley closer to the Press
Upright (2), you will tighten the cables. By moving it further away from the Upright, you will loosen the cables.

26

27

27

The threaded ends on the Press Cable (72) and the Ab
Cable (74) that are attached to the weight stacks can also
be used to tighten the cables.

74
64
97

To tighten the Ab Cable (74), remove the “U”-Bracket (97)
from the Short Weight Tube (17) by removing the 5/16” x
1 3/4” Bolt (96) and the 5/16” Nylon Locknut (64).

72

96

71
68

Tighten the 1/4” Nylon Locknut (68) at the end of the Ab
Cable (74) as far as it will go. Then re-attach the “U”Bracket (97).
17

The Press Cable (72) can be tightened the same way.
When you are tightening the cables, take note that they
are linked into two distinct groups. The Butterfly Cable
(73), the Ab Cable (74), and the Low Pulley Cable (75)
are all connected to the small weight stack. All three
cables will be tightened by tightening the Ab Cable (74)
as described above or by using the Adjustable Pulley
Plates (23) as described on the previous page.
The Press Cable (72) is the only cable attached to the
large weight stack. It must be tightened by using the
method described above or by moving the “V”-Pulleys as
described on the previous page.

Weight Resistance Chart
The chart below shows the approximate weight resistance at each exercise station. “Top” refers to the 6 lb. top
weight; the other numbers refer to the 12.5 lb. weight plates. Note: The actual resistance at each station may
vary due to differences in individual weight plates as well as friction between the cables, pulleys, and
weight guides.

Weight
Plates

High
Pulley
(lbs.)

Arm
Press
(lbs.)

Leg
Press
(lbs.)

Butterfly
(lbs.)

Curl/
Low Pulley
(lbs.)

Ab Pulley/
Leg Raise
(lbs.)

Top

14

16

21

8

10

8

1

28

37

48

23

24

21

2

42

58

75

38

37

35

3

56

79

101

52

50

48

4

69

100

128

67

64

62

5

83

121

155

82

77

76

6

97

142

181

97

90

89

7

111

163

208

8

124

184

235

9

138

205

262

10

152

226

288

27

Ordering Replacement Parts
To order replacement parts, call our Customer Service Department toll-free at 1-888-936-4266, Monday through
Friday, 8 a.m. until 6:30 p.m. EST (excluding holidays). When ordering parts, please be prepared to give the following information:
• The MODEL NUMBER of the product (WECCSY99400)
• The NAME of the product (WEIDER® PRO 99400)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 13 and the EXPLODED
DRAWING on page 14).

LIMITED WARRANTY
ICON OF CANADA INC., (ICON), warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of one (1) year from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All products for which warranty claim
is made must be received by ICON at one of its authorized service centers with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by
ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight
damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service
center, to products used for commercial or rental purposes, or to products used as store display models. No
other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you. The warranty extended hereunder
is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some provinces do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
This warranty gives you specific legal rights. You may also have other rights which vary from province to
province or so specified by the retailer of your equipment.
ICON OF CANADA, 900 de l’Industrie, St-Jérôme, QC J7Y 4B8

Part No. 167295 R0700A

Printed in Canada © 2000 ICON Health & Fitness, Inc.

REMOVE THIS PART IDENTIFICATION
CHART FROM THE MANUAL
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below
each part refers to the key number of the part. Important: Some parts may have been pre-assembled for
shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled.

Note: Assembly is divided into four stages: 1) frame assembly; 2) arm
assembly; 3) cable and pulley assembly; and 4) seat assembly. The
hardware for each assembly stage is packaged separately. Wait until
you begin each stage to open that parts bag.

3/4" Round Inner Cap (43)

1" Round Inner Cap (86)

1” Retainer Ring (31)

1" Square Inner Cap (98)

1 3/4" Square Inner Cap (35)

1" Round Outer Cap (38)

1" Round Inner Cap (76)

2" Square Inner Cap (28)

3/8" x 2 3/4" Bolt (46)

3/8" x 8" Bolt (52)

3/8" x 4 3/4" Bolt (60)

3/8" x 3" Bolt (88)

3/8" x 3 1/4" Bolt (62)

3/8" x 3 1/2" Bolt (56)

3/8" x 3 1/2" Carriage Bolt (95)

3/8" x 3 3/4" Bolt (59)

3/8" x 4" Bolt (78)

3/8" x 4" Carriage Bolt (102)

3/8" x 4 1/4" Bolt (85)

Part Identification Chart–Model No. WECCSY99400

1/4" Nylon Locknut (68)

5/16" Nylon Locknut (64)

R0700A

5/16" x 1 3/4" Bolt (96)

5/16" x 2 1/2" Bolt (87)
3/8" Nylon Locknut (50) 3/8" Nylon Jamnut (63)

5/16" x 2 1/2" Carriage Bolt (92)

1/4" Flat Washer (71)

5/16" Washer (36)

5/16" x 2 3/4" Bolt (89)

1” Tap Screw (80)

3/8" x 1" Bolt (84)

3/8" Flat Washer (48)
3/8" x 1 3/4" Bolt (57)
1/4" x 3/4" Bolt (49)

1/4" x 2 1/2" Bolt (79)

1/4" x 2 1/2" Carriage Bolt (45)

3/8" x 2" Bolt (54)

3/8" x 2 1/2" Bolt (53)

3/8" x 2 1/2" Carriage Bolt (101)

81

REMOVE THIS PART LIST/EXPLODED
DRAWING FROM THE MANUAL

Part List—Model No. WECCSY99400
Key No. Qty.
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
1
10
1
11
1
12
1
13
2
14
1
15
4
16
2
17
1
18
2
19
2
20
1
21
16
22
1
23
2
24
20
25
16
26
2
27
4
28
13
29
2
30
4
31
4
32
4
33
1
34
2
35
7
36
8
37
2
38
2
39
4
40
1
41
1
42
1
43
4
44
2
45
3
46
10
47
2
48
18
49
8
50
32
51
4
52
1
53
2
54
4
Note: “#” indicates

Description

Key No. Qty.

Butterfly Upright
Press Upright
Support Frame
Butterfly Base
Weight Base
Press Base
Press Seat Frame
Press Frame
Press Top Frame
Left Butterfly Arm
Right Butterfly Arm
Backrest
Seat
Butterfly Seat Frame
Weight Guide
Top Weight
Short Weight Tube
Weight Tube Bumper
Weight Pin
Front Leg
Weight
Small Pulley Bracket
Adjustable Pulley Plate
3 1/2” Pulley
Cable Trap
Pro Pulley
“V”-Pulley
2” Square Inner Cap
Butterfly Foam Pad
Foam Pad
Retainer Ring
Large Cable Trap
Butterfly Top Frame
Support Plate, 2 1/2” Center Holes
1 3/4” Square Inner Cap
5/16” Washer
Butterfly Arm Bushing
1” Round Outer Cap
5” Plastic Grip
Bumper
Small Leg Lever
Pad Tube
3/4” Round Inner Cap
Large Bushing
1/4” x 2 1/2” Carriage Bolt
3/8” x 2 3/4” Bolt
Pulley Cover
3/8” Flat Washer
1/4” x 3/4” Bolt
3/8” Nylon Locknut
Weight Bumper
3/8” x 8” Bolt
3/8” x 2 1/2” Bolt
3/8” x 2” Bolt
a non-illustrated part. Specifications are

55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
#
#

1
1
6
1
6
3
1
4
15
31
3
1
1
5
3
1
10
1
1
1
1
2
2
1
5
1
1
2
1
2
1
2
5
1
14
1
1
10
4
2
1
2
2
1
1
2
1
1
1
1
1
1
1

R0700A
Description
Leg Press Plate
3/8” x 3 1/2” Bolt
3/8” x 1 3/4” Bolt
Nylon Strap
3/8” x 3 3/4” Bolt
3/8” x 4 3/4” Bolt
Lat Bar
3/8” x 3 1/4” Bolt
3/8” Nylon Jamnut
5/16” Nylon Locknut
Seat Plate
Weight Top Frame
Chain
1/4” Nylon Locknut
Cable Clip
Long Weight Tube
1/4” Flat Washer
Press Cable
Butterfly Cable
Ab Cable
Low Pulley Cable
1” Round Inner Cap
Press Arm
3/8” x 4” Bolt
1/4” x 2 1/2” Bolt
1” Tap Screw
Ab Strap
4 1/2” Pulley
Leg Press Lever
3/8” x 1” Bolt
3/8” x 4 1/4” Bolt
1” Round Inner Cap
5/16” x 2 1/2” Bolt
3/8” x 3” Bolt
5/16” x 2 3/4” Bolt
Adjustment Tube
Lock Pin
5/16” x 2 1/2” Carriage Bolt
Support Plate, 3 1/2” Center Holes
Support Plate, 4” Center Holes
3/8” x 3 1/2” Carriage Bolt
5/16” x 1 3/4” Bolt
“U”-bracket
1” Square Inner Cap
Press Backrest
Plastic Bushing
3/8” x 2 1/2” Carriage Bolt
3/8” x 4” Carriage Bolt
Adjustment Knob
Curl Post
Curl Pad
User’s Manual
Exercise Poster

subject to change without notice.

43

30

63

11

28

48

63

29

35

38

41

28

37

43

42

75

62

37

80

28

46

40

30

28

31

84

38

36

30

49

105

63

73

104

35

89

48

31

84

75

43

64

26

30

64

64

29

35

10

63

73

86

103

20

13

28

46

65

54

60

43

79

71

14

94 93

25
4

49

92

54

64

59

32

50

25

53

27

28

24

45

24

12

68

28

33

89

25

89

48

1

50

64

92

89

24
47

17

46

48

64

28
24

24

63

51

18

95

21

97

16

96

48

74

15

27

46

57

19

63

79

63

64

25

24

36

50

93

64

25

36

71

74

47

50

32

53

50

5
48

19

21

57

48

64

50

24

71
68

64

64

24

25

92

44

25

24

23

88

64

57

50

24

25

44

83

36

6

60

50

64

28

87

24

50

39

57

36 90

91

50 82

25

50

82

66

57

55

50

63
28

63

23

24

59

50

48

54

15

50

50

59

48

50

28

63

51

18

70

16

96

50

97

72

64

15

71
68

50

34

46

34

85

35

92

48

50

48

72

101

93

49

9

32

81

102

79

71

89

27
50

57

63

22

61

13

24

46

28

69

89

7

94

78

24

25

98

50

50

24

48

77

76

62

62

48

50

27

49

92

24

46

28

50 48

65

32

45

24 25

25

45
65

89

68

63

99

93

39

56

26

89

87

2

25

100

39

35

64

25

36

36

68

8

24

48
62

64

64

52

87

64

39

24

64

71

79

64

50

3

77

67

63

25

76

50 24

35

64

60

59

58

Exploded Drawing—Model No. WECCSY99400
R0700A



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2004:01:15 14:33:02
Producer                        : Acrobat Distiller 4.05 for Macintosh
Author                          : jeanne.sheehan
Creator                         : QuarkXPress Passportª: LaserWriter 8 8.6.5
Title                           : *WECCSY99400 -167295(CEN)
Modify Date                     : 2004:01:15 14:33:14-06:00
Page Count                      : 35

EXIF Metadata provided by EXIF.tools