Weider Weccsy99400 Owner S Manual *WECCSY99400 167295(CEN)

Weider-Pro-9940-System-Weccsy9940-Users-Manual-733588 weider-pro-9940-system-weccsy9940-users-manual-733588

2014-07-06

: Weider Weider-Weccsy99400-Owner-S-Manual weider-weccsy99400-owner-s-manual weider pdf

Open the PDF directly: View PDF .
Page Count: 35

USER’S MANUAL

Model No. WECCSY99400

Serial No.

The serial number is found in the

location shown below. Write the

serial number in the space above.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manu-

al for future reference.

Serial

Number

Decal

Patent Pending

Visit our website at

www.weiderfitness.com

new products, prizes,

fitness tips, and much more!

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if there are

missing parts, we will guarantee

complete satisfaction through

direct assistance from our factory.

TO AVOID UNNECESSARY

DELAYS, PLEASE CALL DIRECT

TO OUR TOLL-FREE CUSTOMER

HOT LINE. The trained techni-

cians on our customer hot line

will provide immediate assis-

tance, free of charge to you.

CUSTOMER HOT LINE:

1-888-936-4266

Mon.–Fri., 8 a.m.–6:30 p.m. EST

(excluding holidays)

Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Cable Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Trouble-shooting and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Weight Resistance Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Ordering Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

One Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART LIST/EXPLODED DRAWING and a PART IDENTIFICATION CHART are attached in the center of

this manual. Remove the PART LIST/EXPLODED DRAWING and the PART IDENTIFICATION CHART before

beginning assembly.

Table of Contents

Important Precautions

WARNING: To reduce the risk of serious injury, read the following important precau-

tions before using the home gym.

1. It is the responsibility of the owner to ensure

that all users of the home gym are adequate-

ly informed of all precautions.

2. Read all instructions in this manual and in

the accompanying literature before using the

home gym.

3. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

4. Use the home gym only on a level surface.

Cover the floor or carpet beneath the home

gym for protection.

5. Inspect and tighten all parts often. Replace

any worn parts immediately.

6. Make sure the cables remain on the pulleys

at all times. If the cables bind while you are

exercising, stop immediately and make sure

the cables are on all of the pulleys.

7. Always stand on a foot plate when perform-

ing an exercise that could cause the home

gym to tip.

8. Keep hands and feet away from moving parts.

9. Keep children under the age of 12 and pets

away from the home gym at all times.

10. Always wear athletic shoes for foot protec-

tion when exercising.

11. Never release the press arms, butterfly arms,

leg lever, lat bar or ab strap while weights are

raised. The weights will fall with great force.

12. Always disconnect the lat bar or ab strap

from the home gym when performing an

exercise that does not use the attachments.

13. The home gym is intended for home use only.

Do not use the home gym in a commercial,

rental or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially

important for persons over the age of 35 or persons with pre-existing health problems. Read all

instructions before using. ICON assumes no responsibility for personal injury or property damage

sustained by or through the use of this product.

ASSEMBLED

DIMENSIONS:

Height: 77 in.

Width: 80 in.

Depth: 55 in.

Low Pulley

Station

Foot Plate

Leg

Lever

Press Arms

Backrest

Curl Pad

Butterfly

Arms

Ab Pulley

Station

Weight

Stacks

Leg Press

Lever

Thank you for selecting the innovative and versatile

WEIDER®PRO 9940 Home Gym. The WEIDER®PRO

9940 offers a unique selection of weight stations

designed to develop every major muscle group of the

body. Whether your goal is to tone your body, build

dramatic muscle size and strength or improve your

cardiovascular system, the WEIDER®PRO 9940

makes it easy to achieve the results you want.

For your benefit, read this manual carefully before

using the WEIDER®PRO 9940 Home Gym. If you

have additional questions, please call our toll-free

HELPLINE at 1-888-936-4266, Monday through

Friday, 8 a.m. until 6:30 p.m. Eastern Time (excluding

holidays). To help us assist you, please note the prod-

uct model number and serial number before calling.

The model number is WECCSY99400. The serial

number can be found on a decal attached to the WEI-

DER®PRO 9940 Home Gym (see the front cover of

this manual).

Please use the drawing below to familiarize your-

self with the major parts and how they fit together.

Before You Begin

Foam Pads

Leg Press

Plate

Backrest

Seat

High Pulley

Station

Lat Bar

Note: This introduction will save you more time

than it takes to read it!

Identifying Parts

To help you identify the small parts used in assem-

bly, we have included a PART IDENTIFICATION

CHART located in the center of this manual. Place

the chart on the floor or work table and use it to

quickly identify different parts as you open the pack-

ages for each step. Note: Some small parts may

have been pre-attached for shipping. If a part is not

in the parts bag, check to see if it has been pre-

attached.

Orienting Parts

As you assemble this product, be sure that all parts

are oriented as shown in the drawings.

Tightening Parts

Tighten all parts as you assemble them, unless

instructed to do otherwise.

Lining Up the Tools

Assembly requires the following tools (not included):

• Two (2) adjustable wrenches

• One (1) standard screwdriver

• One (1) phillips screwdriver

• One (1) rubber mallet

• Lubricant, such as grease or petroleum jelly,

and soapy water

• Tape, such as clear tape or masking tape

Assembly will be more convenient if you have a

socket set, a set of open-end or closed-end wrenches

or a set of ratchet wrenches.

Some assembly steps require two people.

Giving Yourself a Good Start

Before you begin the assembly process itself, take

the time to complete the steps outlined here.

Clearing the Workspace

Clear a workspace that is large enough to hold all

parts and allow you to walk all the way around the

assembled equipment.

Unpacking the Box

To make the assembly process as smooth as possi-

ble, we have broken it into separate stages. All parts

used in each stage are found in individual packages

in the shipping box. Place all parts in a cleared area

and remove the packing materials. Do not dispose of

the packing materials until assembly is completed.

Important: Wait until you begin each assembly

stage to open the parts bag labeled for that

assembly stage.

Assembly

Making Things Easier for Yourself

Everything in this manual is designed to ensure

that our products can be assembled successfully

by anyone. However, it is important to realize

that your new equipment is a sophisticated prod-

uct with many small parts. The assembly process

will take time—possibly several hours. Most peo-

ple find that by setting aside plenty of time, and

by deciding to make the task enjoyable, assem-

bly will go smoothly. You may want to complete

the process over a couple of evenings.

The Four Stages of the Assembly Process

Frame Assembly

You will begin by assembling the base and the

upright frames that serve as the skeleton of the

equipment.

Arm Assembly

This assembly completes the press and butterfly

arms that you operate while you are exercising.

Cable Assembly

This assembly completes the cables and pulleys

that connect the moving arms with each other and

with the weights.

Seat Assembly

This assembly completes the seat and backrest

that support your body while you are exercising.

1. Before beginning, make sure that you have read

and understood the information on page 4.

Locate and open the parts bag labeled “FRAME

ASSEMBLY.”

See drawing 1a. Press a 2” Square Inner Cap (28)

into each end of the Butterfly Base (4). Press two 2”

Square Inner Caps (28) into the Weight Base (5).

Insert four 5/16” x 2 1/2” Carriage Bolts (92) up

through the indicated holes in the Butterfly Base (4).

Insert a 3/8” x 3 1/2” Carriage Bolt (95) up through

the hole at the end of the Butterfly Base. Note: If the

Bolts fall out, secure them by putting a small

piece of tape over the head of each Bolt. Place the

Butterfly Base flat on the floor.

See drawing 1b. Attach the Weight Base (5) to the

Butterfly Base (4) with two 5/16” x 2 3/4” Bolts (89), a

Support Plate with 3 1/2” center holes (93), and two

5/16” Nylon Locknuts (64). Do not tighten the Nylon

Locknuts yet.

Note: There are three kinds of Support Plates. The

main difference between them is the distance

between the holes. When you need a Support

Plate, find the type with holes that will fit over the

Bolts you are using.

2. See drawing 2a. Press a 2” Square Inner Cap (28)

into the end of the Press Base (6).

Attach a 3 1/2” Pulley (24) to each of the brackets on

the Weight Base (5) with a 3/8” x 1 3/4” Bolt (57) and

a 3/8” Nylon Jamnut (63).

Insert four 5/16” x 2 1/2” Carriage Bolts (92) up

through the indicated holes in the Press Base (6).

Insert a 3/8” x 2 1/2” Carriage Bolt (101) and a 3/8 x

4” Carriage Bolt (102) up through the indicated holes

at the end of the Press Base (6).

See drawing 2b. Attach the Press Base (6) to the

Weight Base (5) with two 5/16” x 2 3/4” Bolts (89), a

Support Plate with 3 1/2” center holes (93), and two

5/16” Nylon Locknuts (64). Do not tighten the Nylon

Locknuts yet.

Frame Assembly

102

101

57 57

3. Place the bracket on the lower end of the Butterfly

Upright (1) over the indicated 5/16” x 2 1/2” Carriage

Bolts (92) in the Butterfly Base (4). Hand tighten two

5/16” Nylon Locknuts (64) onto the Bolts. Do not

tighten the Nylon Locknuts yet.

4. Press three 2” Square Inner Caps (28) into the

Butterfly Top Frame (33). Press two 1” Round Inner

Cap (86) into the top of the Butterfly Top Frame (33).

Attach the Butterfly Top Frame (33) to the indicated

bracket at the top of the Butterfly Upright (1) with two

5/16” x 2 3/4” Bolts (89), a Support Plate with 3 1/2”

center holes (93), and two 5/16” Nylon Locknuts (64).

5. Attach the Butterfly Seat Frame (14) to the Front Leg

(20) with two 5/16” x 2 3/4” Bolts (89), two 5/16”

Washers (36), and two 5/16” Nylon Locknuts (64). Do

not tighten the Nylon Locknuts yet.

Slide the bracket on the Front Leg (20) onto the two

5/16” x 2 1/2” Carriage Bolts (92) in the Butterfly Base

(4). Hand tighten two 5/16” Nylon Locknuts (64) onto

the Bolts. Do not tighten the Nylon Locknuts yet.

Attach the Butterfly Seat Frame (14) to the Butterfly

Upright (1) with two 5/16” x 2 3/4” Bolts (89), two

5/16” Washers (36) and two 5/16” Nylon Locknuts

(64). Do not tighten the Nylon Locknuts yet.

7. Press a 1” Square Inner Cap (98) into the small tube

on the Press Upright (2).

Place the bracket on the lower end of the Press

Upright (2) over the indicated 5/16” x 2 1/2” Carriage

Bolts (92) in the Press Base (6). Hand tighten two

5/16” Nylon Locknuts (64) onto the Bolts. Do not

tighten the Nylon Locknuts yet.

Place the bracket on the lower end of the Support

Frame (3) over the indicated 3/8” x 2 1/2” Carriage

Bolt (101) and the 3/8” x 4” Carriage Bolt (102) in the

Press Base (6). Hand tighten a 3/8” Nylon Jamnut

(63) onto the 3/8” x 2 1/2” Carriage Bolt (101). Do not

tighten the Nylon Jamnut yet.

Note: Do not thread a Jamnut onto the 3/8” x 4”

Carriage Bolt (102) yet.

Attach the Support Frame (3) to the Press Upright (2)

with two 5/16” x 2 1/2” Carriage Bolts (92) and two

5/16” Nylon Locknuts (64). Do not tighten the Nylon

Locknuts yet.

6. Press a 2” Square Inner Cap (28) half way into the

top of the Front Leg (20). Press a 2” Square Inner

Cap (28) into each end of the Small Leg Lever (41).

Attach the Bumper (40) to the indicated hole in the

Front Leg (20) with a 1” Tap Screw (80).

Lubricate the 3/8” x 3 1/4” Bolt (62). Attach the Small

Leg Lever (41) to the bracket on the Front Leg (20)

with the Bolt and a 3/8” Nylon Jamnut (63). Do not

overtighten the Nylon Jamnut; it must be easy to

pivot the Leg Lever.

101

102

41 40

Lubricate

8. Press a 2” Square Inner Cap (28) into the Press Top

Frame (9).

Attach the Press Top Frame (9) to the indicated

bracket at the top of the Press Upright (2) with two

5/16” x 2 3/4” Bolts (89), a Support Plate with 3 1/2”

center holes (93), and two 5/16” Nylon Locknuts (64).

10. Lubricate the 3/8” x 3” Bolt (88). Attach the Leg Press

Lever (83) to the Press Base (6) with the Bolt and a

3/8” Nylon Locknut (50). Do not overtighten the

Nylon Locknut; the Leg Press Lever must pivot

easily.

11. Place two Weight Bumpers (51) over the indicated

holes in the Weight Base (5). Slide a Weight Guide

(15) into each of the holes.

Attach the indicated Weight Guide (15) to the Weight

Base (5) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat

Washers (48), and a 3/8” Nylon Locknut (50).

Slide six Weights (21) onto the Weight Guides (15).

Make sure the Weights are turned so the pin

grooves point towards the floor.

Press a Weight Tube Bumper (18) into the lower end

of the Short Weight Tube (17). Slide the Weight Tube

into the center holes in the Weights (21).

Slide a Top Weight (16) onto the Weight Guides (15).

Note: Make sure the Top Weight is turned so the

groove fits over the welded pin on the Weight

Tube (17).

Lubricate

Groove

Grooves

9. Press a 2” Square Inner Cap (28) into the Press Seat

Frame (7).

Slide the bracket on the Press Seat Frame (7) onto

the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the

Press Base (6). Hand tighten two 5/16” Nylon

Locknuts (64) onto the Bolts. Do not tighten the

Nylon Locknuts yet.

Attach the Press Seat Frame (7) to the Press Upright

(2) with two 5/16” x 2 3/4” Bolts (89), two 5/16”

Washers (36), and two 5/16” Nylon Locknuts (64). Do

not tighten the Nylon Locknuts yet.

64 64

548

14. Attach the Weight Top Frame (66) to the Press Top

Frame (9) with one 3/8” x 2 3/4” Bolt (46), a Support

Plate with 4” center holes (94), and a 3/8” Nylon

Locknut (50). Slide a 3 1/2” Pulley (24) with a Cable

Trap (25) onto a 3/8” x 4” Bolt (78). Insert the Bolt

through the Support Plate (94) and hand tighten a

3/8” Nylon Locknut (50) onto it.

Attach the Weight Top Frame (66) to the bracket on

the Press Upright (2) with two 3/8” x 2 3/4” Bolts (46),

a Support Plate with 2 1/2” center holes (34) and two

3/8” Nylon Locknuts (50). Do not tighten the Nylon

Locknuts yet.

12. Place two Weight Bumpers (51) over the indicated

holes in the Weight Base (5). Slide a Weight Guide

(15) into each of the holes.

Attach the indicated Weight Guide (15) to the Weight

Base (5) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat

Washers (48), and a 3/8” Nylon Locknut (50).

Slide ten Weights (21) onto the Weight Guides (15).

Make sure the Weights are turned so the pin

grooves point towards the floor.

Press a Weight Tube Bumper (18) into the lower end

of the Long Weight Tube (70). Slide the Weight Tube

into the center holes in the Weights (21).

Slide a Top Weight (16) onto the Weight Guides (15).

Note: Make sure the Top Weight is turned so the

groove fits over the welded pin on the Weight

Tube (70).

51 51

13. Place the Weight Top Frame (66) on the indicated

brackets on the Uprights (1 and 2). Note: The four

Weight Guides (15) must be behind the Weight

Top Frame, as shown in step 14.

Attach the Weight Top Frame (66) to the Butterfly Top

Frame (33) with two 3/8” x 2 3/4” Bolts (46), a

Support Plate with 4” center holes (94), and two 3/8”

Nylon Locknuts (50). Do not tighten the Nylon

Locknuts yet.

Attach the Weight Top Frame (66) to the bracket on

the Butterfly Upright (1) with two 3/8” x 2 3/4” Bolts

(46), a Support Plate with 2 1/2” center holes (34),

and two 3/8” Nylon Locknuts (50). Do not tighten the

Nylon Locknuts yet.

Groove

Brackets

Grooves

15. Attach each of the four Weight Guides (15) to the

Weight Top Frame (66) with a 3/8” x 3 3/4” Bolt (59),

a 3/8” Flat Washer (48), and a 3/8” Nylon Locknut

(50).

Important: Go back and fully tighten all Nylon

Locknuts used in steps 1 through 15.

17. Press a 1 3/4” Square Inner Cap (35) into the top of a

Press Arm (77). Press a 1” Round Inner Cap (76) into

the indicated hole in the Press Arm.

Attach the Press Arm (77) to the bracket on the Press

Frame (8) with two 5/16” x 2 1/2” Bolts (87) and two

5/16” Nylon Locknuts (64).

Repeat this step to assemble the second Press Arm

(77, not shown).

100

Welded

Tube

Lubricate

Arm Assembly

16. Locate and open the parts bag labeled “ARM

ASSEMBLY.”

Press a Plastic Bushing (100) onto each welded tube

on the Press Frame (8).

Lubricate the 3/8” x 8” Bolt (52). Attach the Press

Frame (8) to the welded tubes on the Press Base (6)

with the Bolt and a 3/8” Nylon Locknut (50). Do not

overtighten the Nylon Locknut; it must be easy to

pivot the Press Frame.

20. Open the bag marked Pulley Bag 2 and remove one

“V”-Pulley (27). Keep the rest of the pulleys in the bag

for future identification.

Wrap the Butterfly Cable (73) around a “V”-Pulley

(27) in the direction shown. Attach the “V”-Pulley and

a Large Cable Trap (32) to the bracket on the back

of the Butterfly Upright (1) with a 3/8” x 2 1/2” Bolt

(53) and a 3/8” Nylon Locknut (50). Make sure the

Large Cable Trap is oriented as shown.

19. Locate and open the parts bag labeled “CABLE

ASSEMBLY.” For Cable identification and routing

during steps 19 to 49, refer to the Cable Diagrams

and Cable ID Chart on pages 23 and 24.

Identify the Butterfly Cable (73). It is approximately

52” long and it has a closed loop on each end. Attach

the Butterfly Cable to the bracket on the Left Butterfly

Arm (10) with a 3/8” x 1” Bolt (84) and two 3/8” Nylon

Jamnuts (63). Note: The loop on the Cable and the

two Nylon Jamnuts must be mounted underneath

the welded bracket.

18. Press a 1 3/4” Square Inner Cap (35) into each end

of the Right Butterfly Arm (11). Wet the lower end of

the Arm with soapy water. Slide a Butterfly Foam Pad

(29) onto the lower end of the Arm.

Lubricate the indicated axle on the Butterfly Top

Frame (33). Orient the Right Butterfly Arm (11) as

shown and slide it onto the axle. Secure the Butterfly

Arm with two Retainer Rings (31) and a 1” Round

Outer Cap (38). Note: Place the Retainer Rings on

top of the inverted Outer Cap and gently tap the

Cap onto the axle with a hammer. Make sure the

teeth on the Retainer Rings bend towards the Cap

as shown in the inset drawing.

Repeat this step to assemble the Left Butterfly Arm

(10, not shown).

Axle

Bracket

Teeth

Axle

Cable Assembly

23. Attach the Butterfly Cable (73) to the bracket on the

Right Butterfly Arm (11) with a 3/8” x 1” Bolt (84) and

two 3/8” Nylon Jamnuts (63). Note: The loop on the

Cable and the two Nylon Jamnuts must be mount-

ed underneath the welded bracket.

11 63

Bracket

24. Identify the Ab Cable (74). It is approximately 224”

long, and it has a ball on one end and a threaded

shaft on the other. You will start by attaching the end

of the Cable with the ball.

Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in

the direction shown. Place two Pulley Covers (47)

over the Pulley, so that the slots in the Pulley Covers

are placed over the Cable. Attach the Pulley and

Pulley Covers to the indicated hole in the Butterfly

Upright (1) with a 3/8” x 3 3/4” Bolt (59), two 3/8” Flat

Washers (48), and a 3/8” Nylon Jamnut (63). Make

sure the Cable is between the Pulley and the

welded pin on the Upright.

74 24

22. Wrap the Butterfly Cable (73) around a “V”-Pulley

(27) in the direction shown. Attach the “V”-Pulley and

a Large Cable Trap (32) to the bracket on the back

of the Butterfly Upright (1) with a 3/8” x 2 1/2” Bolt

(53) and a 3/8” Nylon Locknut (50). Make sure the

Large Cable Trap is oriented as shown.

Bracket

21. Remove both 3 1/2” Pulleys (24) from the pre-assem-

bled Small Pulley Bracket (22).

Wrap the Butterfly Cable (73) around a 3 1/2” Pulley

(24) in the direction shown. Attach the Pulley to the

Small Pulley Bracket (22) with a 3/8” x 1 3/4” Bolt

(57) and a 3/8” Nylon Locknut (50). Make sure the

Small Pulley Bracket is oriented exactly as

shown.

26. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in

the direction shown. Attach the Pulley to the Small

Pulley Bracket (22) with a 3/8” x 1 3/4” Bolt (57) and

a 3/8” Nylon Locknut (50). Make sure the Pulley

Bracket is oriented as shown.

25. Remove both 3 1/2” Pulleys (24) from the pre-assem-

bled Adjustable Pulley Plates (23).

Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in

the direction shown. Attach the Pulley and a Cable

Trap (25) to the top hole in the two Adjustable Pulley

Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon

Locknut (50). Make sure the Cable Trap and the

Pulley Plates are oriented as shown.

27. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in

the direction shown. Attach the Pulley and a Cable

Trap (25) to the welded bracket on the Butterfly Base

(4) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut

(50). Make sure the Cable Trap is oriented as

shown.

29. Wrap the Ab Cable (74) around a 4 1/2” Pulley (82) in

the direction shown. Attach the Pulley inside the indi-

cated bracket on the Weight Top Frame (66) with a

3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50).

Make sure the threaded end of the Ab Cable is

routed through the bracket, as shown.

28. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in

the direction shown. Slide the Pulley and a Cable

Trap (25) onto the 3/8” x 3 1/2” Carriage Bolt (95)

already inserted into the Butterfly Base (4). Secure

the Pulley with a 3/8” Nylon Jamnut (63). Make sure

the Cable Trap is oriented as shown.

Route the threaded end of the Ab Cable (74) under

the 3 1/2” Pulley (24) that is already mounted on the

Weight Base (5). Make sure the Cable is routed in

the direction shown.

Note: For clarity, this and the following drawings

show some parts removed.

28 63

Bracket

End of

Cable

30. Attach the threaded end of the Ab Cable (74) to a “U”-

Bracket (97) with a 1/4” Flat Washer (71) and a 1/4”

Nylon Locknut (68).

Attach the “U”-Bracket (97) to the hole in the Short

Weight Tube (17) with a 5/16” x 1 3/4” Bolt (96) and a

5/16” Nylon Locknut (64). Note: Do not completely

tighten the Nylon Locknut; it should be threaded

only two turns onto the end of the Cable, as

shown in the inset drawing.

31. Remove a Pro Pulley (26) from the bag marked

Pulley Bag 2.

Identify the Low Pulley Cable (75). It is approximately

143 1/2” long and it has a ball on one end and a loop

on the other. Route the end with the loop through the

slot in the cable guide on the Butterfly Base (4).

Route the Low Pulley Cable (75) under a Pro Pulley

(26) as shown. Attach the Pro Pulley and a Cable

Trap (25) to the bracket on the Butterfly Base (4) with

a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).

Make sure the Cable Trap is oriented as shown.

54 26

Cable

Guide

32. Wrap the Low Pulley Cable (75) around a 3 1/2”

Pulley (24) in the direction shown. Attach the Pulley

and a Cable Trap (25) to the indicated hole in the

Butterfly Upright (1) with a 3/8” x 4 3/4” Bolt (60) and

a 3/8” Nylon Jamnut (63). Note: Thread the Jamnut

only two turns onto the Bolt, since you will later

attach another Pulley to the Bolt. Make sure the

Cable Trap is oriented as shown.

33. Wrap the Low Pulley Cable (75) over a 3 1/2” Pulley

(24) in the direction shown. Attach the Pulley and a

Cable Trap (25) to the lower hole in the Adjustable

Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8”

Nylon Locknut (50). Make sure the Cable Trap is

oriented as shown.

34. Remove the 3/8” Nylon Jamnut (63) from the

3/8” x 4 3/4” Bolt (60) inserted into the Butterfly

Upright (1) in step 32.

Wrap the Low Pulley Cable (75) around a 3 1/2”

Pulley (24) in the direction shown. Attach the Pulley

and a Cable Trap (25) to the 3/8” x 4 3/4” Bolt (60)

with the 3/8” Nylon Jamnut (63). Make sure the

Cable Trap is oriented as shown.

35. Attach the loop on the end of the Low Pulley Cable

(75) to the indicated hole in the Small Leg Lever (41)

with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat Washers

(48), and a 3/8” Nylon Jamnut (63).

36. Remove a Pro Pulley (26) from the bag marked

Pulley Bag 2.

Identify the Press Cable (72). It is approximately 389

1/2” long with a ball on one end and a threaded shaft

on the other. Begin by attaching the end with the ball.

Wrap the Press Cable (72) around a Pro Pulley (26)

in the direction shown. Attach the Pulley to the indi-

cated hole in the Press Top Frame (9) with a 3/8” x

3 1/2” Bolt (56), a 3/8” Flat Washer (48), and a 3/8”

Nylon Jamnut (63). Make sure the Cable is between

the Pulley and the welded pin on the Press Top

Frame.

37. Route the threaded end of the Press Cable (72)

around the 3 1/2” Pulley (24) that is already mounted

on the Top Frame (9).

38. Wrap the Press Cable (72) around a 3 1/2” Pulley (24)

in the direction shown. Attach the Pulley to the indicat-

ed hole in the Press Upright (2) with a 3/8” x 3 3/4”

Bolt (59), a 3/8” Flat Washer (48) and a 3/8” Nylon

Locknut (50). Make sure the Cable Trap is oriented

as shown.

63 26

39. Important: Although the following steps are not

difficult to perform, the correct routing of the

cable is critical to the functioning of the home

gym. Please make sure that you wrap the cable

around the pulleys exactly as shown in each step.

Route the Press Cable (72) through the opening in

the Press Frame (8), and wrap the Cable around a

3 1/2” Pulley (24) in the direction shown. Route the

end of the Cable back through the opening in the

Press Frame.

Attach the Pulley (24) to the indicated hole in the

Press Frame (8) with a 3/8” x 3 1/4” Bolt (62), a 3/8”

Flat Washer (48) and a 3/8” Nylon Locknut (50).

Make sure the Pulley is mounted on the inside of

the Press Frame. Make sure the Cable Trap is ori-

ented as shown.

40. Wrap the Press Cable (72) around a “V”-Pulley (27) in

the direction shown. Attach the “V”-Pulley and a Large

Cable Trap (32) to the small tube on the Press

Upright (2) with a 3/8” x 3 1/4” Bolt (62), a 3/8” Flat

Washer (48) and a 3/8” Nylon Locknut (50). Note:

The small tube has four adjustment holes. Mount

the “V”-Pulley in the hole farthest from the

Upright. Make sure the Cable Trap is oriented as

shown.

Small tube,

last hole

41. Route the Press Cable (72) back through the opening

in the Press Frame (8) and wrap the Press Cable

around a 3 1/2” Pulley (24) in the direction shown.

Then, route the Press Cable back through the open-

ing in the Press Frame (8).

Attach the Pulley (24) to the indicated hole in the

Press Frame (8) with a 3/8” x 3 1/4” Bolt (62), a 3/8”

Flat Washer (48), and a 3/8” Nylon Locknut (50).

Make sure the Pulley is mounted on the inside of

the Press Frame. Make sure the Cable Trap is ori-

ented as shown.

42. Wrap the Press Cable (72) around a 3 1/2” Pulley

(24) in the direction shown. Attach the Pulley and a

Cable Trap (25) to the indicated hole on the far side

of the Press Upright (2) with a 3/8” x 4 3/4” Bolt (60)

and a 3/8” Nylon Jamnut (63). Note: Thread the

Jamnut only two turns onto the Bolt; you will later

attach another Pulley to the Bolt. Make sure the

Cable Trap is oriented as shown.

Route the Press Cable (72) back through the opening

in the Press Frame (8), so the end is in front of the

Press Frame.

43. Wrap the Press Cable (72) around a 3 1/2” Pulley

(24) in the direction shown. Attach the Pulley and a

Cable Trap (25) to the indicated hole on the far side

of the Leg Press Lever (83) with a 3/8” x 4 3/4” Bolt

(60) and a 3/8” Nylon Jamnut (63). Note: Thread the

Jamnut only two turns onto the Bolt; you will later

attach another Pulley to the Bolt. Make sure the

Cable Trap is oriented as shown.

44. Wrap the Press Cable (72) around a “V”-Pulley (27)

in the direction shown. Attach the “V”-Pulley and a

Large Cable Trap (32) underneath the Press Seat

Frame (7) with a 3/8” x 4 1/4” Bolt (85), a 3/8” Flat

Washer (48), and a 3/8” Nylon Locknut (50). Note:

the Press Seat Frame has five adjustment holes.

Mount the “V”-Pulley in the hole closest to the

Leg Press Lever. Make sure the Cable Trap is ori-

ented as shown.

45. Wrap the Press Cable (72) around a 3 1/2” Pulley

(24) in the direction shown. Attach the Pulley and a

Cable Trap (25) to the near side of the Leg Press

Lever (83). Use the 3/8” x 4 3/4” Bolt (60) that was

inserted in step 43 and secure the Pulley with the

3/8” Nylon Jamnut (63). Make sure the Cable Trap

is oriented as shown.

46. Wrap the Press Cable (72) around a 3 1/2” Pulley

(24) in the direction shown. Attach the Pulley and a

Cable Trap (25) to near side of the Press Upright (2).

Use the 3/8” x 4 3/4” Bolt (60) that was inserted in

step 42 and secure the Pulley with the 3/8” Nylon

Jamnut (63). Make sure the Cable Trap is oriented

as shown.

Wrap the Press Cable (72) around a 3 1/2” Pulley

(24) in the direction shown. Attach the Pulley and a

Cable Trap (25) to the 3/8” x 4” Carriage Bolt (102)

that was inserted into the Press Base (6) earlier.

Secure the Pulley with the 3/8” Nylon Locknut (50).

Make sure the Cable Trap is oriented as shown.

102

47. Route the threaded end of the Press Cable (72)

around the 3 1/2” Pulley (24) that was mounted on the

bracket on the Weight Base (5) in an earlier step.

48. Wrap the Press Cable (72) over a 4 1/2” Pulley (82)

in the direction shown. Attach the Pulley inside the

indicated bracket on the Weight Top Frame (66) with

a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut

(50). Make sure the end of the Cable is routed

through the bracket, as shown.

50 82

49. Attach the threaded end of the Press Cable (72) to

the remaining “U”-Bracket (97) with a 1/4” Flat

Washer (71) and a 1/4” Nylon Locknut (68).

Attach the “U”-Bracket (97) to the hole in the Long

Weight Tube (70) with a 5/16” x 1 3/4” Bolt (96) and a

5/16” Nylon Locknut (64). Note: Do not completely

tighten the Nylon Locknut; it should be threaded

only two turns onto the end of the Cable, as

shown in the inset drawing.

Important: Follow all four cables from end to end

and make sure that they rest in the grooves of all

pulleys and that the cables and the pulleys move

smoothly.

70 68

Seat Assembly

50. Locate and open the parts bag labeled “SEAT

ASSEMBLY.”

Attach the Backrest (12) to the indicated holes in the

Butterfly Upright (1) with two 1/4” x 2 1/2” Bolts (79)

and two 1/4” Flat Washers (71).

51. Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the

center hole in a Seat Plate (65). Attach the Seat Plate

to the Press Backrest (99) with two 1/4” x 3/4” Bolts

(49).

Insert the 1/4” x 2 1/2” Carriage Bolt (45) into the

indicated hole in the Butterfly Upright (2) and secure

it with a 1/4” Flat Washer (71) and a 1/4” Nylon

Locknut (68). Secure the other end of the Press

Backrest (99) with a 1/4” x 2 1/2” Bolt (79) and a 1/4”

Flat Washer (71).

Miscellaneous Assembly

52. Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the

center hole in a Seat Plate (65). Attach the Seat Plate

to a Seat (13) with two 1/4” x 3/4” Bolts (49).

Insert the 1/4” x 2 1/2” Carriage Bolt (45) into the indi-

cated hole in the Butterfly Seat Frame (14) and

secure it with a 1/4” Flat Washer (71) and a 1/4”

Nylon Locknut (68). Secure the other end of the Seat

(13) with a 1/4” x 2 1/2” Bolt (79) and a 1/4” Flat

Washer (71).

Attach the other Seat (13) to the Press Seat Frame

(7, not shown) in the same manner.

55. Attach the Curl Pad (105) to the Curl Post (104) with

two 1/4” x 3/4” Bolts (49).

71 79

104

105

53. Press 3/4” Round Inner Caps (43) into the ends of the

Pad Tube (42) and the indicated tube on the Front

Leg (20).

Insert the Pad Tube (42) into the indicated hole in the

Small Leg Lever (41). Slide Foam Pads (30) onto the

ends of the Pad Tube and the tube on the Leg Lever.

30 Tube

54. Press a 1 3/4” Square Inner Cap (35) into the indicat-

ed end of the Adjustment Tube (90).

Attach the Adjustment Tube (90) to the bracket (not

visible in the drawing) on the back of the Leg Press

Plate (55) with a 5/16” x 2 1/2” Bolt (87), two 5/16”

Washers (36), and a 5/16” Nylon Locknut (64).

Attach the Leg Press Plate (55) to the Leg Press

Lever (83) by placing the Adjustment Tube (90) into

the bracket on top of the Leg Press Lever and secur-

ing it with the Lock Pin (91). Note: The lip on the

Leg Press Plate must be on the upper edge.

56. Apply the WEIDER PRO 9940 decal in the location shown. Important: The warning decals shown below

have been attached to the home gym in the locations shown. If a decal is missing or illegible, please

call our customer hotline at the number on the front cover of this manual to order a replacement

decal. Apply the new decal in the appropriate location.

57. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in

ADJUSTMENT, beginning on page 25 of this manual.

Before using the home gym, pull each cable a few times to make sure that the cables move smoothly over

the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the

cables are not properly installed, they may be damaged when heavy weight is used. If there is any

slack in the cables, you will need to remove the slack by tightening the cables. See TROUBLE-

SHOOTING AND MAINTENANCE on page 26.

WEIDER

PRO 9940

Cable Diagrams

The Cable Diagrams below and on the next page show the proper routing of the Butterfly Cable (73), the Ab

Cable (74), the Low Pulley Cable (75) and the Press Cable (72). The numbers show the correct route for each

Cable. Make sure that the Cables are routed correctly, that the Pulleys move smoothly, and that the

Cable Traps do not touch or bind the Cables. Incorrect cable routing can damage the home gym.

Low Pulley Cable (75)

Ab Cable (74)

Butterfly Cable (73)

Cable ID Chart

73, 52”

75, 143.5”

74, 224”

72, 389.5”

711

Press Cable (72)

Adjusting the Leg Press Plate

To adjust the position of the Leg Press Plate (55), pull out

the Lock Pin (91) and slide the Adjustment Tube (90)

backwards or forwards in the bracket on the Leg Press

Lever (83). Line up one of the adjustment holes in the

Adjustment Tube with the hole in the bracket and re-insert

the Lock Pin.

Attaching the Lat Bar, Nylon Strap or Ab Strap to the

High Pulley Station

Attach the Lat Bar (61) to the Press Cable (72) with a

Cable Clip (69). For some exercises, the Chain (67)

should be attached between the Lat Bar and the High

Cable with two Cable Clips. Adjust the length of the

Chain between the Lat Bar and the High Cable so the

Lat Bar is in the correct starting position for the exer-

cise to be performed.

The Nylon Strap (58) or Ab Strap (81) can be attached in

the same manner.

Attaching the Lat Bar, Nylon Strap or Ab Strap to the

Low Pulley Station

Attach the Lat Bar (61) to the Low Pulley Cable (75) with

a Cable Clip (69). For some exercises, the Chain (67)

should be attached between the Lat Bar and the Low

Pulley Cable with two Cable Clips. Adjust the length of

the Chain between the Lat Bar and the Low Pulley

Cable so the Lat Bar is in the correct starting position

for the exercise to be performed.

The Nylon Strap (58) or Ab Strap (81) can be attached in

the same manner.

Adjustment

Changing the Weight Setting

To change the setting of the weight stack, insert a Weight

Pin (19) under the desired Weight (21). Make sure you

insert the Weight Pin as far as it will go. Note: Due to the

cables and pulleys, the amount of resistance at each

exercise station may vary from the weight setting.

Use the WEIGHT RESISTANCE CHART on page 27 to

find the approximate amount of resistance at each

weight station.

The instructions below describe how each part of the home gym can be adjusted. Refer to the exercise poster

accompanying this manual to see how the home gym should be set up for each exercise. IMPORTANT: When

using an attachment, make sure it is in the correct starting position for the exercise to be performed. If

there is any slack in the cables or chain as an exercise is performed, the effectiveness of the exercise

will be reduced.

Slack can be removed form the Press Cable (72) by

moving one or both of the “V”-Pulleys (27) on the Press

Cable.

One “V”-Pulley (27) is attached to the small tube on the

Press Upright (2). There are three free holes in the small

tube, and you can move the “V”-Pulley to any one of

them to tighten the cables. Start by moving the “V”-

Pulley one hole, and then one more, as needed.

The second “V”-Pulley (27) is attached to the Press Seat

Frame (7). There are five adjustment holes in the Seat

Frame. By moving the “V”-Pulley closer to the Press

Upright (2), you will tighten the cables. By moving it fur-

ther away from the Upright, you will loosen the cables.

23 Adjustment

Holes

Trouble-shooting and Maintenance

Inspect and tighten all parts each time you use the home gym. Replace any worn parts immediately. The

home gym can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.

Tightening the Cables

If a cable slips off the pulleys often, the cable may have become twisted. Remove the cable and re-install

it. If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

The type of cable used on the home gym can stretch slightly when it is first used. If there is slack in the cables

before resistance is felt, the cables should be tightened. Slack can be removed from the cables in several differ-

ent ways:

72 27

105

103

104

The Adjustable Pulley Plates (23) have several sets of

adjustment holes. By moving one or both pulleys (24) to

a different set of holes, you will tighten the cables.

To move a Pulley (24), remove the 3/8” Nylon Locknut

(50) and the 3/8” x 2” Bolt (54). Remove the Cable Trap

(25) and Pulley from the Adjustable Pulley Plates (23).

Re-attach the Pulley and Cable Trap to the appropriate

adjustment hole in the Pulley Plates. Note: Begin by

moving one Pulley to the second adjustment hole. If

the cables are still too loose, move the same Pulley

to the third hole. If additional adjustment is needed,

move the other Pulley until the cables are tight.

To use the Curl Pad (105), remove the 2” Square Inner

Cap (28) from the Front Leg (20) and insert the Curl Post

(104) into the Front Leg. Secure the Curl Pad by inserting

the Adjustment Knob (103) at the desired height.

The threaded ends on the Press Cable (72) and the Ab

Cable (74) that are attached to the weight stacks can also

be used to tighten the cables.

To tighten the Ab Cable (74), remove the “U”-Bracket (97)

from the Short Weight Tube (17) by removing the 5/16” x

1 3/4” Bolt (96) and the 5/16” Nylon Locknut (64).

Tighten the 1/4” Nylon Locknut (68) at the end of the Ab

Cable (74) as far as it will go. Then re-attach the “U”-

Bracket (97).

The Press Cable (72) can be tightened the same way.

When you are tightening the cables, take note that they

are linked into two distinct groups. The Butterfly Cable

(73), the Ab Cable (74), and the Low Pulley Cable (75)

are all connected to the small weight stack. All three

cables will be tightened by tightening the Ab Cable (74)

as described above or by using the Adjustable Pulley

Plates (23) as described on the previous page.

The Press Cable (72) is the only cable attached to the

large weight stack. It must be tightened by using the

method described above or by moving the “V”-Pulleys as

described on the previous page.

High Arm Leg Butterfly Curl/ Ab Pulley/

Weight Pulley Press Press (lbs.) Low Pulley Leg Raise

Plates (lbs.) (lbs.) (lbs.) (lbs.) (lbs.)

Top 14 16 21 8 10 8

128 37 48 23 24 21

242 58 75 38 37 35

356 79 101 52 50 48

469 100 128 67 64 62

583 121 155 82 77 76

697 142 181 97 90 89

7111 163 208

8124 184 235

9138 205 262

10 152 226 288

The chart below shows the approximate weight resistance at each exercise station. “Top” refers to the 6 lb. top

weight; the other numbers refer to the 12.5 lb. weight plates. Note: The actual resistance at each station may

vary due to differences in individual weight plates as well as friction between the cables, pulleys, and

weight guides.

Weight Resistance Chart

LIMITED WARRANTY

ICON OF CANADA INC., (ICON), warrants this product to be free from defects in workmanship and material,

under normal use and service conditions, for a period of one (1) year from the date of purchase. This warran-

ty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repair-

ing, at ICON's option, the product at one of its authorized service centers. All products for which warranty claim

is made must be received by ICON at one of its authorized service centers with all freight and other trans-

portation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by

ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight

damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service

center, to products used for commercial or rental purposes, or to products used as store display models. No

other warranty beyond that specifically set forth above is authorized by ICON.

ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection

with the use or performance of the product or damages with respect to any economic loss, loss of property,

loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-

ages of whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or conse-

quential damages. Accordingly, the above limitation may not apply to you. The warranty extended hereunder

is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particu-

lar purpose is limited in its scope and duration to the terms set forth herein. Some provinces do not allow lim-

itations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-

chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.

This warranty gives you specific legal rights. You may also have other rights which vary from province to

province or so specified by the retailer of your equipment.

ICON OF CANADA, 900 de l’Industrie, St-Jérôme, QC J7Y 4B8

To order replacement parts, call our Customer Service Department toll-free at 1-888-936-4266, Monday through

Friday, 8 a.m. until 6:30 p.m. EST (excluding holidays). When ordering parts, please be prepared to give the fol-

lowing information:

• The MODEL NUMBER of the product (WECCSY99400)

• The NAME of the product (WEIDER®PRO 99400)

• The SERIAL NUMBER of the product (see the front cover of this manual)

• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 13 and the EXPLODED

DRAWING on page 14).

Ordering Replacement Parts

Note: Assembly is divided into four stages: 1) frame assembly; 2) arm

assembly; 3) cable and pulley assembly; and 4) seat assembly. The

hardware for each assembly stage is packaged separately. Wait until

you begin each stage to open that parts bag.

REMOVE THIS PART IDENTIFICATION

CHART FROM THE MANUAL

This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below

each part refers to the key number of the part. Important: Some parts may have been pre-assembled for

shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled.

3/4" Round Inner Cap (43)

1” Retainer Ring (31)

1" Round Outer Cap (38)

1" Square Inner Cap (98)

1 3/4" Square Inner Cap (35)

1" Round Inner Cap (76)

1" Round Inner Cap (86)

2" Square Inner Cap (28)

3/8" x 3 1/2" Bolt (56)

3/8" x 4 3/4" Bolt (60)

3/8" x 2 3/4" Bolt (46)

3/8" x 3" Bolt (88)

3/8" x 3 1/2" Carriage Bolt (95)

3/8" x 3 3/4" Bolt (59)

3/8" x 8" Bolt (52)

3/8" x 3 1/4" Bolt (62)

3/8" x 4" Bolt (78)

3/8" x 4 1/4" Bolt (85)

3/8" x 4" Carriage Bolt (102)

3/8" Nylon Locknut (50) 3/8" Nylon Jamnut (63)

5/16" Nylon Locknut (64)

1” Tap Screw (80)

3/8" x 2" Bolt (54)

1/4" Flat Washer (71)

5/16" x 1 3/4" Bolt (96)

3/8" Flat Washer (48)

1/4" x 3/4" Bolt (49)

1/4" x 2 1/2" Bolt (79)

3/8" x 1" Bolt (84)

1/4" Nylon Locknut (68)

5/16" Washer (36)

5/16" x 2 1/2" Bolt (87)

5/16" x 2 3/4" Bolt (89)

5/16" x 2 1/2" Carriage Bolt (92)

3/8" x 1 3/4" Bolt (57)

3/8" x 2 1/2" Bolt (53)

3/8" x 2 1/2" Carriage Bolt (101)

1/4" x 2 1/2" Carriage Bolt (45)

Part Identification Chart–Model No. WECCSY99400 R0700A

REMOVE THIS PART LIST/EXPLODED

DRAWING FROM THE MANUAL

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice.

Part List—Model No. WECCSY99400 R0700A

Key No. Qty. Description Key No. Qty. Description

1 1 Butterfly Upright

2 1 Press Upright

3 1 Support Frame

4 1 Butterfly Base

5 1 Weight Base

6 1 Press Base

7 1 Press Seat Frame

8 1 Press Frame

9 1 Press Top Frame

10 1 Left Butterfly Arm

11 1 Right Butterfly Arm

12 1 Backrest

13 2 Seat

14 1 Butterfly Seat Frame

15 4 Weight Guide

16 2 Top Weight

17 1 Short Weight Tube

18 2 Weight Tube Bumper

19 2 Weight Pin

20 1 Front Leg

21 16 Weight

22 1 Small Pulley Bracket

23 2 Adjustable Pulley Plate

24 20 3 1/2” Pulley

25 16 Cable Trap

26 2 Pro Pulley

27 4 “V”-Pulley

28 13 2” Square Inner Cap

29 2 Butterfly Foam Pad

30 4 Foam Pad

31 4 Retainer Ring

32 4 Large Cable Trap

33 1 Butterfly Top Frame

34 2 Support Plate, 2 1/2” Center Holes

35 7 1 3/4” Square Inner Cap

36 8 5/16” Washer

37 2 Butterfly Arm Bushing

38 2 1” Round Outer Cap

39 4 5” Plastic Grip

40 1 Bumper

41 1 Small Leg Lever

42 1 Pad Tube

43 4 3/4” Round Inner Cap

44 2 Large Bushing

45 3 1/4” x 2 1/2” Carriage Bolt

46 10 3/8” x 2 3/4” Bolt

47 2 Pulley Cover

48 18 3/8” Flat Washer

49 8 1/4” x 3/4” Bolt

50 32 3/8” Nylon Locknut

51 4 Weight Bumper

52 1 3/8” x 8” Bolt

53 2 3/8” x 2 1/2” Bolt

54 4 3/8” x 2” Bolt

55 1 Leg Press Plate

56 1 3/8” x 3 1/2” Bolt

57 6 3/8” x 1 3/4” Bolt

58 1 Nylon Strap

59 6 3/8” x 3 3/4” Bolt

60 3 3/8” x 4 3/4” Bolt

61 1 Lat Bar

62 4 3/8” x 3 1/4” Bolt

63 15 3/8” Nylon Jamnut

64 31 5/16” Nylon Locknut

65 3 Seat Plate

66 1 Weight Top Frame

67 1 Chain

68 5 1/4” Nylon Locknut

69 3 Cable Clip

70 1 Long Weight Tube

71 10 1/4” Flat Washer

72 1 Press Cable

73 1 Butterfly Cable

74 1 Ab Cable

75 1 Low Pulley Cable

76 2 1” Round Inner Cap

77 2 Press Arm

78 1 3/8” x 4” Bolt

79 5 1/4” x 2 1/2” Bolt

80 1 1” Tap Screw

81 1 Ab Strap

82 2 4 1/2” Pulley

83 1 Leg Press Lever

84 2 3/8” x 1” Bolt

85 1 3/8” x 4 1/4” Bolt

86 2 1” Round Inner Cap

87 5 5/16” x 2 1/2” Bolt

88 1 3/8” x 3” Bolt

89 14 5/16” x 2 3/4” Bolt

90 1 Adjustment Tube

91 1 Lock Pin

92 10 5/16” x 2 1/2” Carriage Bolt

93 4 Support Plate, 3 1/2” Center Holes

94 2 Support Plate, 4” Center Holes

95 1 3/8” x 3 1/2” Carriage Bolt

96 2 5/16” x 1 3/4” Bolt

97 2 “U”-bracket

98 1 1” Square Inner Cap

99 1 Press Backrest

100 2 Plastic Bushing

101 1 3/8” x 2 1/2” Carriage Bolt

102 1 3/8” x 4” Carriage Bolt

103 1 Adjustment Knob

104 1 Curl Post

105 1 Curl Pad

# 1 User’s Manual

# 1 Exercise Poster

50 24

24 60

101 102 89

57 22

81 69

24 47

71 79

64 32

28 28

100

105

104

103

53 64

60 24

28 42

36 20

18 16

50 82

50 82 46

23 24 25

85 89

24 25

48 48

Exploded Drawing—Model No. WECCSY99400 R0700A

Weider Weccsy99400 Owner S Manual *WECCSY99400 167295(CEN)

Weider-Pro-9940-System-Weccsy9940-Users-Manual-733588 weider-pro-9940-system-weccsy9940-users-manual-733588

Navigation menu

Versions of this User Manual:

Views

Navigation