Westell CSICPBHMG-AW4 The Co-Pilot Beacon User Manual D960 1146 002 r004 MANUAL ICEbreaker III indd

Westell, Inc. The Co-Pilot Beacon D960 1146 002 r004 MANUAL ICEbreaker III indd

USERS MANUAL

CSI-CPBH-MG-C4, CSI-CPBH-MG-P4, CSI-CPBH-MG-C2/P2, CSI-CPBH-MG-AW4, CSI-CPBH-MG-C2/AW2, CSI-CPBH-MG-P2/AW2, CSI-CPBH-MO-C4, CSI-CPBH-MO-P4, CSI-CPBH-MO-C2/P2, CSI-CPBH-MO-AW4, CSI-CPBH-MO-C2/AW2, CSI-CPBH-MO-P2/AW2, CSI-CPBH-MX-C4, CSI-CPBH-MX-P4, CSI-CPBH-MX-C2/P2, CSI-CPBH-MX-AW4 , CSI-CPBH-MX-C2/AW2, CSI-CPBH-MX-P2/AW2,
This page intentionally left blank.
Table of ContentsProduct Registration Information .................................................................................................................................................................... 4Document Purpose / Intended Users ............................................................................................................................................................. 4Radio and Television Interference .................................................................................................................................................................. 4Application ...................................................................................................................................................................................................... 4Safety Guidelines ........................................................................................................................................................................................... 4Important Safety Information .......................................................................................................................................................................... 4Acronyms and De• nitions ...............................................................................................................................................................................5Product Introduction ....................................................................................................................................................................................... 5Functional Overview ....................................................................................................................................................................................... 6Electrical Characteristics ................................................................................................................................................................................ 6Mechanical Speci• cations ..............................................................................................................................................................................6AC Power Speci• cations ................................................................................................................................................................................6Environmental Requirements ......................................................................................................................................................................... 6 Mechanical Drawing ...................................................................................................................................................................................... 7System Set-Up Considerations ...................................................................................................................................................................... 7Mounting the Co-Pilot Beacon ........................................................................................................................................................................ 7Typical Co-Pilot/BTS Interconnection with Internal CDMA Timing (MO Series) ............................................................................................. 8Typical Co-Pilot/Repeater Interconnection with Internal GPS Timing (MG Series) ........................................................................................ 9Typical Co-Pilot/Repeater Interconnection with External TM-4 (MX Series) ................................................................................................ 10Optional Accessories .................................................................................................................................................................................... 11Important Installation Notes .......................................................................................................................................................................... 11Powering Up the Unit.................................................................................................................................................................................... 11Local Communication Interface Ports........................................................................................................................................................... 11EIA232 Pin Speci• cations ............................................................................................................................................................................ 12USB Interface ............................................................................................................................................................................................... 12Ethernet ........................................................................................................................................................................................................ 12Monitoring & Alarms ..................................................................................................................................................................................... 12Text Menu Interface ...................................................................................................................................................................................... 13Local Access................................................................................................................................................................................................. 13User Interface ............................................................................................................................................................................................... 15Login ............................................................................................................................................................................................................. 15Main Menu .................................................................................................................................................................................................... 15Telnet Session (Remote Access) .................................................................................................................................................................. 16Set Parameters Menu................................................................................................................................................................................... 16Set Parameters Menu................................................................................................................................................................................... 19Co-Pilot Beacon Con• guration ..................................................................................................................................................................... 20Transmitter Con• guration ............................................................................................................................................................................. 20System Con• guration ................................................................................................................................................................................... 21Networking Con• guration ............................................................................................................................................................................. 22System Commands ...................................................................................................................................................................................... 23Key Features ................................................................................................................................................................................................ 24Multiple Beacon Con• guration...................................................................................................................................................................... 24Detected RF Power Shutdown ..................................................................................................................................................................... 24Timing Reference Source ............................................................................................................................................................................. 24Control Parameter Details ............................................................................................................................................................................ 24Master Shutdown.......................................................................................................................................................................................... 24Timing Reference Selection ......................................................................................................................................................................... 24Channel Frequency Numbers....................................................................................................................................................................... 25Signal Transmit Enables ............................................................................................................................................................................... 25PN Offset ...................................................................................................................................................................................................... 26Tau (Delay Correction).................................................................................................................................................................................. 26Co-pilot beacon Per Channel Transmit Power ............................................................................................................................................. 26Composite Transmit Power .......................................................................................................................................................................... 26Manual Shutdown ......................................................................................................................................................................................... 26Auto Shutdown Enable ................................................................................................................................................................................. 26Auto Shutdown Threshold ............................................................................................................................................................................ 26Index..............................................................................................................................................................................................................30
-4-This guide should be applied whenever a need exists to add pilot beacon capability to an existing system or when this capability is being included with a new installation.The general safety information in this guideline applies to both operating and service personnel. Speci! c warnings and cautions will be found in other parts of this manual where they apply, but may not appear in this summary. Failure to comply with these precautions or speci! c warnings elsewhere in the manual violates safety standards of design, manufacture, and intended use of equipment. Cellular Specialties, Inc. assumes no liability for the customer’s failure to comply with these requirements: Grounding This pilot beacon system is designed to operate from 100-240 VAC and should always be operated with the ground wire properly connected. Do not remove or otherwise alter the grounding lug on the power cord. Explosive Atmospheres To avoid explosion or ! re, do not operate this product in the presence of " ammable gases or fumes. Lightning Danger Do not install or make adjustments to this unit during an electrical storm. Use of a suitable lightning arrester, such as CSI’s model number CSI-CAP, is very strongly recommended.No User Serviceable Parts Inside HAZARDOUS VOLTAGES ARE PRESENT WHEN THE COVER IS REMOVED. Opening the chassis will void your warranty. If you suspect a malfunction with this product, call your dealer or the Cellular Specialties Support Line at: (603) 626-6677, Toll Free (USA) 1-877-844-4274.The purpose of this document is to provide a step-by-step procedure to help the experienced technician/engineer install and commission an in-building wireless enhancement pilot beacon system. Following the procedures outlined will minimize risks associated with modifying a live system and prevent service interruptions. This document assumes the technician/engineer understands the basic principles and functionality involved with the system. It is geared to the practical concerns of the installer. Antennas used for the purpose of radiating signals indoors are limited to a maximum gain of 3 dBi. Each antenna must be positioned to observe minimum separation requirements from all users and bystanders. The following guidelines should be used when considering separation distances.INDOOR antennas must be placed such that, under normal conditions, personnel cannot come within 20 cm (~8.0 in.) from any inside antenna. Adhering to this minimum separation will ensure that the employee or bystander cannot exceed RF exposures beyond the maxi-mum permissible limit as de! ned by section 1.1310 i.e. limits for General Population/Uncontrolled Exposure.Document Purpose / Intended UsersApplicationSafety GuidelinesImportant Safety Information Product Registration InformationDISCLAIMER: All information and statements contained herein are accurate to the best of the knowledge of Cellular Specialties, Inc. (CSI), but Cellular Specialties makes no warranty with respect thereto, including without limitation any results that may be obtained from the products described herein or the infringement by such products of any proprietary rights of any persons. Use or application of such information or statements is at the users sole risk, without any liability on the part of Cellular Specialties, Inc. Nothing herein shall be construed as licence or recommendation for use, which infringes upon any proprietary rights of any person. Product material and speci! cations are subject to change without notice. Cellular Specialties’ standard terms of sale and the speci! c terms of any particular sale apply.The serial number may be found on the label on the bottom panel near the power connectors. Note this number below. Retain this manual, along with proof of pur-chase, to serve as a permanent record of your purchase. MODEL NUMBER SERIAL NUMBER PURCHASE DATE POINT OF SALE COMPANYNOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a resi-dential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes and Modi! cations not expressly approved by Cellular Specialties, Inc. can void your authority to operate this equipment under Federal Communications Commission’s rules. Radio and Television Interference
-5-The pilot beacon generator facilitates E911 and other location based services (LBS) for in building and/or DAS based installations of CDMA2000/1xEV-DO cellular networks. In these situations the normal methods based for location determination, direct reception of GPS by the mobile station or triangulation using the signals from multiple base stations, do not work. Signals from the GPS system are suf• ciently weak that even if the mobile station’s GPS receiver might ultimately be able to lock on to the satellites, the acquisition time will be too long. And since indoor service is typically provided either by a single strong local cell or by using a repeater, there aren’t multiple signals on which to triangulate while DAS based deployments result in too many signals with indeterminate timing. By placing a pilot signal at a known PN offset the LBS algorithm can quickly and reliably be made aware that it is within a speci• c building or other location where normal location determining solutions are ineffective. This information can be used to aid the GPS receiver in acquiring signals if they are present or be used as a position report directly until more accurate information becomes available.3GPP2 The standards body comprised of representatives of interested companies that is responsible for the development and maintenance of the operational standards for the CDMA2000 system. Http://www.3gpp2.orgAGC Automatic Gain ControlCDMA Code Division (or, Domain) Multiple Access: The general term for the technology used in the CDMA2000 system as well as others. Also a shorthand reference to the CDMA2000 system and its derivatives such as 1xEV-DOChip A single element, a ‘1’ or a ‘0’, of the PN Sequence in a CDMA system. The chip rate for the CDMA2000 system is 1.2288 Mchips/second.CSI Cellular Specialties IncorporatedDAS Distributed Antenna SystemERP Effective Radiated PowerEST Even Second Tick: In the CDMA2000 cellular system all time values are referenced to the start of the even seconds of time as indicated by GPS.FCC Federal Communications CommissionFPGA Field Programmable Gate ArrayGPS Global Positioning SystemIF Intermediate FrequencyLED Light Emitting DiodeNEMA National Electrical Manufacturers AssociationPA Power Ampli• erPN Pseudo random Number: A number chosen by some algorithm that approximates a random process. Can be short for “PN Sequence”, “PN Number”, or “PN Offset” when discussing the CDMA2000 system.PN Number In the CDMA2000 system only a subset of the possible PN Offsets are used for base station identi• cation. Each of these allowed offsets is given a unique number from 0 to 511.PN Offset In the CDMA2000 System each base station is identi• ed by the offset in time from the EST at which the start of the Pilot PN Sequence occurs. The offset is speci• ed in terms of number of chips.PN Sequence A sequence of pseudo random numbers. In the CDMA2000 system several such sequences are used. The one relevant to ICEBreaker is the Pilot, or Short, sequence which is a 215 element long sequence of ones and zeros.PPS Pulse per Second: Refers the pulse repetition rate of the timing signal used as a time reference. RF Radio FrequencySBC Single Board ComputerTau Timing Offset or Delay Adjustment: In the CDMA2000 system the timing of the downlink signal is required to be aligned with the EST as it is transmitted from the antenna. Tau allows the timing of the internal PN Sequence to be adjusted to compensate for the delays of the base station hardware such that the timing will be correct at the antennaUSB Universal Serial Bus Acronyms and Defi nitions Product Introduction
-6- Functional OverviewColor Satin Black Weight 8.4lbs / 3.8kg Thermal Management Fan Cooled Surface Coating Powder Coat Parameter Specifi cation NotesPilot Beacon Size Height 1.73 in. Width 19.00 in. Depth 18.02 in. Mechanical Specifi cations AC Voltage 100 - 240 VAC External Power SupplyAC Power Frequency 47 - 63 Hz AC Current 1.7 Amps @ 120 VAC 0.9 Amps @ 230 VAC Heat Output 500 BTU/Hr Relative Humidity 5% to 95% Non-condensing Temperature Range -30° to +48°C (-22° to +118°F) AC Power Specifi cationsParameter Specifi cation Notes Environmental RequirementsParameter Specifi cation NotesElectrical CharacteristicsCharacteristic Performance Limit Number of Bands per Beacon 1CDMA Band Class 0 (Cell), 1 (PCS) and 15 (AWS)Max # Simultaneous Channels/Beacon 8 (Cell) 11 (PCS and AWS) Number of Unique PN Offsets/Beacon 1Composite TX Power +20 dBmSpurious Emissions Limits < -45 dBc Δf .75 to 1.98 MHZ< -60 dBc Δf 1.98 to 4.0 MHZ< -65 dBc Δf 4.0 to 16 MHZ< -75 dBc Δf > 16 MHZCarrier Frequency Accuracy 20 Hz (.2 ppm) Cell Band40 Hz (.2 ppm) PCS Band45 Hz (.2 ppm) AWS BandWhen locked to GPSPilot Timing Jitter < 10 nsec rms, <50 nsec peakRho > 0.98Tau Adjustment Range - 166.7 to + 166.7 µsec (+/- 25.6 CDMA chips)Tau Adjustment Resolution 20 nsec (one 40th of a CDMA chip)
-7- Mechanical Drawing All cables should be checked for shorts and opens. Also verify that there are no cables with loose or poor connections. It is critical that the installer contact the service provider before the system is turned on.The following diagram illustrates the best method for mounting the pilot beacon to a wall in an typical installation. System Set-Up ConsiderationsMounting the Co-Pilot Beacon
-8-+9.6dBm +9.0dBm-10.4dBmDirectional Coupler 2 (-20dB)+8.9dBm +8.3dBm-15.1dBmDirectional Coupler 3 (-20dB)+20.0dBmBTSCo-Pilot Beacon (MO Series)Equipped with Praecis II CDMA Timing Module -10.5dBm+20.0dBm-0.1dBm-15.2dBm-50.2dBmDASRF JumperNM-NMRF JumperNM-NMIN OUT-20dBRF JumperNM-SMAMRF JumperNM-SMAM-15.8dBm-15.9dBmINOUT -20dBSee note 4NetworkIN OUT-30dBDirectional Coupler 1 (-30dB)RF JumperNM-NM+19.9dBm20dB Fixed AttenuatorRF JumperNM-TNCM-10.1dBm-60.1dBm+9.7dBm-16.0dBm+19.9dBm-68.5dBm-16.2dBm-138.5dBm-138.6dBm20dB Fixed AttenuatorSee note 6Notes:1. It is recommended that all unused ports be terminated at 50 ohms. When properly terminated, the possibility of false shutdown is minimized because high reflections at open ports are eliminated.2. The values shown in this drawing are only an example. Power levels encountered at each installation may require different coupling, pads, and threshold values.3. This example assumes a BTS with power at the output set to 40dBm, co-pilot beacon output set at 20dBm. 4. Threshold Power Level in this example is set to -20dBm (Approximately 10dB below the power level at the monitor input.) 5. DAS Power Detection and Shutdown functionality:- If RF Detector measures Input power lower than the Threshold Power Level set by the user, then the Co-Pilot Beacon’s RF power output will be shut down.- An alarm occurs. (Delay approximately one second on-off and one second off-on.6. Co-pilot beacon signal reflecting back to the input of the CDMA timing source must never be allowed to exceed -124dBm.-60.2dBm10dB Fixed Attenuator10dB Fixed Attenuator20dB Fixed AttenuatorTypical Co-Pilot/BTS Interconnection with Internal CDMA Timing (MO Series)
-9-Typical Co-Pilot/Repeater Interconnection with Internal GPS Timing (MG Series)+9.9dBm +9.3dBm-10.1dBmDirectional Coupler 1 +9.2dBm +8.6dBm-15.1dBmDirectional Coupler 2+10.0dBmDonor-75.0dBm-10.2dBm-0.1dBm-15.2dBm-50.2dBmDASIN OUT-20dB+19.9dBm-15.8dBm-15.9dBmINOUT -20dBSee note 4GPS AntennaAntenna BracketRF JumperNF-TNCMRF JumperNM-SMAMRF JumperNM-SMAM+20.0dBmRF JumperNF-TNCMRF JumperNM-NMRF JumperNM-NMCo-Pilot Beacon (MG Series) Equipped with Trimble Embedded GPS Timing Receiver Notes:1. It is recommended that all unused ports be terminated at 50 ohms. When properly terminated, the possibility of false shutdown is minimized because high reflections at open ports are eliminated.2. The values shown in this drawing are only an example. Power levels encountered at each installation may require different coupling, pads, and threshold values.3. This example assumes -75dBm input at the repeater, repeater gain set to 85dB, co-pilot beacon output set at 20dBm and use of 20dB directional couplers with 20dB coupling, and assumed 15dB worst case directivity.4. Threshold Power Level in this example is set to -20dBm (Approximately 10dB below the power level at the monitor input.) 5. DAS Power Detection and Shutdown functionality:- If RF Detector measures Input power lower than the Threshold Power Level set by the user, then the Co-Pilot Beacon’s RF power output will be shut down.- An alarm occurs. (Delay approximately one second on-off and one second off-on.Repeater
-10-+9.9dBm +9.3dBm-10.1dBmDirectional Coupler 1 +9.2dBm +8.6dBm-15.1dBmDirectional Coupler 2+10.0dBmDonor-75.0dBm-10.2dBm-0.1dBm-15.2dBm-50.2dBmDASIN OUT-20dB+19.9dBm-15.8dBm-15.9dBmINOUT -20dBSee note 4GPS AntennaAntenna BracketRF JumperNF-TNCMRF JumperNM-SMAMRF JumperNM-SMAM+20.0dBmRF JumperNF-TNCMRF JumperNM-NMRF JumperNM-NMCo-Pilot Beacon (MX Series)Notes:1. It is recommended that all unused ports be terminated at 50 ohms. When properly terminated, the possibility of false shutdown is minimized because high reflections at open ports are eliminated.2. The values shown in this drawing are only an example. Power levels encountered at each installation may require different coupling, pads, and threshold values.3. This example assumes -75dBm input at the repeater, repeater gain set to 85dB, co-pilot beacon output set at 20dBm and use of 20dB directional couplers with 20dB coupling, and assumed 15dB worst case directivity.4. Threshold Power Level in this example is set to -20dBm (Approximately 10dB below the power level at the monitor input.) 5. DAS Power Detection and Shutdown functionality:- If RF Detector measures Input power lower than the Threshold Power Level set by the user, then the Co-Pilot Beacon’s RF power output will be shut down.- An alarm occurs. (Delay approximately one second on-off and one second off-on.RepeaterRF JumperBNCM-TNCMTM-4Typical Co-Pilot/Repeater Interconnection with External TM-4 (MX Series)
-11-During Power up, the pilot beacon will require approximately three minutes for the internal computer to boot up. During this time the LED on the front panel may light and go out several times. When boot is complete and no alarm conditions exist, the LED indicators will be illuminated green. Do not unplug the unit while it is in the boot up process! Powering Up the Unit To allow monitoring and control, the pilot beacon is equipped with four ports that provide external communication access (1 Ethernet CAT-5, 1 DB-9 serial, and 2 USB). The Ethernet, CAT-5 port is provided as a primary communications port to the PC. One serial inter-face, COM 1, can provide communications to local PC. The USB interface provides a means to download ! les from a memory device. The DB-9 pin assignments of COM 1 conform to the standard Electronic Industries Association (EIA232) speci! cation. A diagram of the pin descriptions is provided on the next page for reference.Connecting a null modem cable to the COM 1 port and using a terminal emulation program with a PC will allow communication to the control processor’s Text Menu Interface (TMI) for trouble shooting and advanced diagnostics. Call CSI technical support for assistance if you need to access these advanced features or for further information.The proprietary external GPS receiver connection is made at the port labeled “GPS”. Do not connect other devices or non-straight-through serial extension cables to this port. Place the GPS receiver in a location with the best view of the unobstructed sky that is possible, although a 100% open view of the sky is not necessary to achieve a stable time lock.Local Communication Interface Ports• The installer should refer to the Safety Guidelines section and the Important Safety Information section for proper antenna selection and installation. To avoid serious injury or death and damage to the pilot beacon, do not install server antennas near overhead power lines or high power components. Allow enough distance so that if antennas should fall they will not come in contact with those components.• Close proximity to the server antennas with the pilot beacon in operation may expose the user or installer to RF ! elds that exceed FCC limits for human exposure.WARNING! PILOT BEACON AND/OR HANDSET DAMAGE MAY OCCUR IF A HANDSET IS CONNECTED DIRECTLY TO THE PILOT BEACON OR THE COAX THAT LEADS TO THE PILOT BEACON. Important Installation NotesA complete line of accessories is available from Cellular Specialties, Inc. Check with your CSI distributor for any additional items needed. Below are just a few examples suitable for most in-building needs.• Directional Couplers 6dB - model number: CSI-DC6/700-2.7K/N 10dB - model number: CSI-DC10/700-2.7K/N 15dB - model number: CSI-DC15/700-2.7K/N 20dB - model number: CSI-DC20/700-2.7K/N 30dB - model number: CSI-DC30/700-2.7K/N Battery backup, 4 hr Single band 2 hour dual band - model number: CS48-985-601• Power Dividers 2:1 - model number: CSI-SPD2/700-2.7K/N 3:1 - model number: CSI-SPD3/700-2.7K/N 4:1 - model number: CSI-SPD4/700-2.7K/N • Grounding Kit - model number: CSI-GKIT • Lightning Arrestor - model number: CSI-CAP• Inside Omnidirectional Antenna Quad-band - model number: CSI-AO/700/2.7K/3 Optional AccessoriesWarning: Power supply cable connector is keyed for proper orientation and is designed to lock into place. Keyed for proper alignment, do notforce connectorinto place.
-12- EIA232 Pin Specifi cationsThe diagram above is for reference only, it’s intended to provide a quick source for pinout information in the event it should be neces-sary to adapt your serial cable because of an unusual connector con• guration. In the vast majority of cases this information will not be needed.There are no physical connections provided to exclusively and speci• cally communicate system or alarm status. Information with regard to system or alarm status is provided by the GUI accessible via the communication ports described earlier.The Universal Serial Bus (USB) interface conforms to Intel’s Universal Host Controller Interface (UHCI) version 1.1 dated March 21, 1996. This interface will support data transfer rates up to 12 Mbps and can be used for software updates.The Ethernet AUI conforms to IEEE 802.3 and is capable of supporting 10/100 Mbps communications speeds. This port is used to pro-vide access to the UI. USB InterfaceEthernet Monitoring & Alarms
-13- Text Menu InterfaceFigure 1Figure 2Local access to the pilot beacon TMI, also known as the console interface, is made by connecting a serial cable (optional), as shown in ! gure 1, from the serial connector of the laptop the serial port on the bottom end panel of the pilot beacon. This connector is labeled COM In some cases, if the gender of the connector is not the same as shown in ! gure 1, a null modem adapter (optional) as shown in ! gure 2 may also be required. Local Access
-14-Pressing “OK” will open up a blank dialog screen. Go to the setup dropdown menu and select Serial port to make changes to the serial port setup.Con• gure the terminal program for the correct COM port, in this case COM 1 and 115200 baud rate as shown below.Many terminal emulation programs will work if properly con• gured. In the following description, “TeraTerm” is used to establish the TMI session. This program is readily available via the Internet and is free from Ayera Technologies at: http://www.ayera.com/teraterm/TeraTerm Pro Web works on Windows 95/98, 2000, XP. Here is the latest TeraTerm Pro Web release: Version 3.1.3, October 8, 2002. ttpro313.zipWhen the program is started, the following screen is displayed.Select the Serial radio button and press OK as shown below.Note: It may be necessary, in the System Properties section of the control panel; using DeviceManager to determine what COM port your computer uses for the communications port. In this case it is COM 1. This is not to be con-fused with the serial port on the bottom panel of the repeater labeled COM 1.
-15- User InterfaceUpon successful login the unit displays the main menu. Main MenuOnce the unit has completed its boot up and link initialization phases it will display the login prompt. The username is “bandone” for the ! rst two beacons and “bandtwo” for the second two beacons. The password is “csi1234”. Login
-16-The diagram below shows the normal use of Crossed and Straight cables. Straight Cable Crossed Cable Telnet Session (Remote Access) Set Parameters MenuOnce the maintenance mode login is performed successfully the main menu will be displayed again but without the “(Disabled)” quali! er on the “Set Parameters” choice.When “Set Parameters” is ! rst selected the unit will ask for the maintenance mode login. (The default username for the maintenance mode is “csi” and the password is “csi1234”.)Straight CableStraight CableCrossed CablePCPCHub orSwitchCo-PilotBeaconCo-PilotBeaconPin # Signal AT&T 258A1 Transmit+ White/Orange2 Transmit- Orange/White or Orange3 Receive+ White/Green4 N/A Blue/White or Blue5 N/A White/Blue6 Receive- Green/White or Green7 N/A White/Brown8 N/A Brown/White or BrownPin # Signal AT&T 258A1 Receive+ White/Orange2 Receive- Orange/White or Orange3 Transmit+ White/Green4 N/A Blue/White or Blue5 N/A White/Blue6 Transmit- Green/White or Green7 N/A White/Brown8 N/A Brown/White or BrownA B12345678876543211234567887654321
-17-Remote access to the repeater may be gained through a LAN connection and a terminal emulation program for TCP/IP. As with the se-rial connection, many terminal emulation programs will work, if properly con• gured. In the following description, “TeraTerm” is used to establish the Telnet session. Also, it will be required that the network con• guration of the computer and the repeater being controlled be set up with the same Sub Net and Sub Net Mask in order to establish a link. In other words, the IP addresses of both the computer used and the repeater must use the same group of IP address number sets. For example, the repeater ships with the default IP address of 192.168.1.100 and a Sub Net Mask of 255.255.255.0. In order to connect, the computer to be used for the link would normally need an IP address of something like 192.168.1.12 with a Sub Net Mask of 255.255.255.0, the same Sub Net Mask as the repeater. In this example note: the last digit of the IP address may be any number except 1,100 and 255. Con• guring your PC is normally fairly straight forward but it does vary somewhat with the operating system involved. If you require assistance, contact your IT department and they will be able to set up your PC for you or you may review the Additional Tips Section at the end of the manual.When the TeraTerm program is started, the following screen is displayed. Change the default host IP address to the IP address of the repeater to be controlled. In the case of a new install, the default address is 192.168.1.100 and has been assigned at the factory. Select the service Telnet. The TCP Port must be 23. Pressing the “OK” button will display the security alert shown below. Click the yes button and the • rst SSH2 Authentication Challenge screen is displayed. The user then types the username in the space provided. In multi beacon units, each set of beacons are changed independently and requires an independent login. To make changes default user names are “bandone” for the • rst two beacons and “bandtwo” for the second two beacons respectively .
-18-In the • eld provided, type the user name for the beacon to be changed. The default password is “csi1234” for all beacons. After typing the password press OK and the main menu will be displayed as shown next.Press OK after entering the user name and the second SSH2 Authentication Challenge will be displayed.
-19- Set Parameters MenuOnce the maintenance mode login is performed successfully the main menu will be displayed again but without the “(Disabled)” quali• er on the “Set Parameters” choice.When “Set Parameters” is • rst selected the unit will ask for the maintenance mode login. (The default username for the maintenance mode is “csi” and the password is “csi1234”.)Selection of option 1 will display the Co-Pilot Con• guration Menu. Option 2 displays the Networking Con• guration Menu. These menus allow the user to choose set up options menus that are fairly self explanatory but are displayed in the following pages for clari• cation.
-20- Co-Pilot Beacon Confi gurationSelecting option 1 will display the current beacon con• guration but does not allow the user to change any setting.Acceptable power range is 0-20Selection of option 2 allows for the setting of Transmitter and System Con• guration.* Note Top line parenthesis shows current value. Bottom line shows range of acceptable values.***Acceptable channel rangeSee next page for the Set System Con• guration selections.When selecting each option on the Set Transmitter Con• guration menu the user is presented with the Select Transmitter menu • rst to allow for the selection of transmitter for this section of the unit. Transmitter Confi guration
-21- System Confi guration
-22- Networking Confi gurationIf the user is unclear about the network con• guration that should be used for setup of the Co-Pilot Beacon, he or she should contact the Network Administrator for information with regard to the speci• c network settings.
-23- System CommandsThe System Commands Menu will allow the user to upgrade and restore the unit OS, restore factory calibration settings, upload new data • les, upgrade FTP software, reboot and shutdown the system.
-24- Key Features Multiple Beacon Confi gurationEach unit contains four independent beacons. These can be all in the same band or two of one band and two of another. Detected RF Power ShutdownThe product contains an RF power detector for each transmitter that can be used to sense the power being transmitted by the DAS. Loss of the DAS requires that the beacon be shut down in order to provide some possibility for mobile devices to connect to the low level signal of the macro network.The shutdown threshold is set by the user. When the detected power falls below the set threshold the transmit power of all beacons is shut down and an alarm is issued. When the power rises above the threshold the beacons are turned back on. Timing Reference SourceA GPS derived timing reference is always required for the proper operation of the Co-co-pilot beacon. That timing reference can be provided by one of the following: • An optional internal GPS receiver • An optional internal CDMA timing receiver • The CSI supplied external CDMA Timing Reference Receiver • The CSI supplied external precision GPS Timing Reference (Spectrum Instruments TM-4) • Any user-supplied GPS Receiver capable of providing a TTL compatible even second tick aligned to GPS (not UTC) time. Control Parameter Details Master ShutdownThe Master Shutdown shuts down the transmissions from all beacons in the product. Timing Reference SelectionThere are three alternatives for the timing reference source and all beacons in the product use the same reference. • Internal GPS • Internal CDMA • External Even Second SyncThe choices that are available will depend on the product type as follows: -MX- “External” only -MG- “External” and “Internal GPS” -MO- “External” and “Internal CDMAThe default choice will also depend on the product type as follows: -MX- “External” -MG- “Internal GPS” -MO- “Internal CDMASelecting “Internal GPS” enables the use of the internal GPS receiver. An appropriate antenna with a clear view of the sky must be connected to the “Timing In” connector of the Co-pilot beacon. This choice is only available if the unit includes the optional GPS timing reference.Selecting “Internal CDMA” enables the use of the internal CDMA receiver. Either an appropriate antenna, or a cable carrying a valid CDMA Base Station signal, must be connected to the “Timing In” connector of the Co-pilot beacon. This choice is only available if the unit includes the optional CDMA timing reference.Selecting “External Even Second” enables the use of a TTL compatible even second pulse via the “EST In” connector of the Co-Co-pilot beacon. The rising edge of the pulse is used as the time reference and must be aligned with the start of the even second of GPS (not UTC) Time.The even second tick provided by the selected Timing Reference will appear on the “EST Out” connector.
-25-Each co-pilot beacon can transmit up to eleven simultaneous CDMA2000 signals. The carrier frequency for each signal is set by entering the desired CDMA channel number for that signal.Thus, there are eleven Channel Number • elds, one for each of the possible signals.The CDMA channel number is a unit less integer valueThe range is 1 to 799 and then 991 to 1023 for cell band, 1 to 1199 for PCS band, and 25 to 875 for AWS band. Duplicate channel num-bers are not allowed.The default values for a Cell Band beacon are: Signal 1: CDMA Channel 384 Signal 2: CDMA Channel 425 Signal 3: CDMA Channel 466 Signal 4: CDMA Channel 507 Signal 5: CDMA Channel 548 Signal 6: CDMA Channel 589 Signal 7: CDMA Channel 770 Signal 8: CDMA Channel 1 Signal 9: CDMA Channel 9 Signal 10: CDMA Channel 10 Signal 11: CDMA Channel 11The default values for PCS and AWS Band beacons are: Signal 1: CDMA Channel 1 Signal 2: CDMA Channel 2 Signal 3: CDMA Channel 3 Signal 4: CDMA Channel 4 Signal 5: CDMA Channel 5 Signal 6: CDMA Channel 6 Signal 7: CDMA Channel 7 Signal 8: CDMA Channel 8 Signal 9: CDMA Channel 9 Signal 10: CDMA Channel 10 Signal 11: CDMA Channel 11Each of the eleven signals for a given beacon can be individually turned on or off. There is one transmit enable • eld for each signal.The default values for a Cell Band beacon are: Signal 1: Enabled Signal 2 Enabled Signal 3: Enabled Signal 4: Enabled Signal 5: Enabled Signal 6: Enabled Signal 7: Enabled Signal 8: Disabled Signal 9: Disabled Signal 10: Disabled Signal 11: DisabledThe default values for PCS and AWS Bands beacons are: Signal 1: Disabled Signal 2 Disabled Signal 3: Disabled Signal 4: Disabled Signal 5: Disabled Signal 6: Disabled Signal 7: Disabled Signal 8: Disabled Signal 9: Disabled Signal 10: Disabled Signal 11: Disabled Channel Frequency Numbers Signal Transmit Enables
-26- PN OffsetEach beacon has its own PN Offset. The PN Offset is a unitless integer value with a range of 0 to 511. The default value is zero. Tau (Delay Correction)There is a single Tau value for each beacon in a given product unit. Tau is a real value in units of microseconds with a range of -166.7 to +166.7 μsec and one decimal place of precision. Internally the value will be rounded to the nearest 1/40th of a CDMA chip. Co-pilot beacon Per Channel Transmit PowerThis setting controls the CDMA Channel Power output by a given Co-pilot beacon for each carrier. All enabled carriers are transmitted at the same power level. The total transmit power will be the sum of the power of all enable carriers. The user must set this power level such that the total transmit power does not exceed the specifi ed maximum transmit power for the Co-pilot beacon.The Output Power is specifi ed in dBm with a range of 0.0 to 20.0 and a resolution of 0.5. Composite Transmit PowerComposite output power is a display only fi eld. The value is calculated from the Per Channel Tx Power and the number of channels that are enabled. Manual Shutdown Manual Shutdown allows the user to shut down transmission from the given beacon Auto Shutdown EnableThe detected power shutdown feature can be enabled or disabled. Auto Shutdown ThresholdThe shutdown threshold is entered in units of dBm.The allowable range is -26 to +4 dBm Detected PowerDetected power is a display only fi eld that displays the current reading of the power detector for the given beacon. The measured power is displayed in units of dBm and has a range of -30 to +10.
-27-Instructions to change TCP/IP settings on your Windows computer.Click in the Network Connections Icon in the Control Panel. See below.Right click on Local Area Connection - and select “Properties”.Scroll down to “Internet Protocol (TCP/IP) and click on the “Properties” button. Additional Tips
-27-If you are set up to use DHCP, the window shown below will be displayed. Select “Use the following IP address:” and enter “192.168.1.2.” The subnet mask should automatically populate to “255.255.255.0”.Nothing else will need to be chosen or entered. Click “OK”, then “OK again and retry connection.A crossover Ethernet cable (supplied) must be used for Web Interface access. As a reminder, you must verify the Ethernet port on your laptop is powered. If your laptop is on battery power, the Ethernet port may be inactive by default. If this is the case simply plug in the laptop to a 110vac source or change the power settings to enable the Ethernet port when the laptop is using battery power.
-29-Seller warrants that its products are transferred rightfully and with good title; that its products are free from any lawful security interest or other lien or encumbrance unknown to Buyer; and that for a period of one year from the date of installation or fi fteen months from the date of original shipment, whichever period expires fi rst, such products will be free from defects in material and workmanship which arise under proper and normal use and service. Buyer’s exclusive remedy hereunder is limited to Seller’s correc-tion (either at its plant or at such other place as may be agreed upon be-tween Seller and Buyer) of such defects by repair or replacement at no cost to Buyer. Transportation costs in connection with the return of products to Seller’s plant or designated facility shall be paid by Buyer. The provi-sions of this warranty shall be applicable with respect to any product which Seller replaces pursuant to it. SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, OTHER THAN AS SPECIFICALLY STATED ABOVE. EXPRESS-LY EXCLUDED ARE THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PURPOSE. THE FOREGOING SHALL CONSTITUTE ALL OF SELLER’S LIABILITY (EXCEPT AS TO PATENT INFRINGEMENT) WITH RESPECT TO THE PRODUCTS. IN NO EVENT SHALL SELLER BE LIABLE FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES, INSTALLA-TION COSTS, LOST REVENUE OR PROFITS, OR ANY OTHER COSTS OF ANY NATURE AS A RESULT OF THE USE OF PRODUCTS MANUFACTURED BY THE SELLER, WHETHER USED IN ACCORDANCE WITH INSTRUCTIONS OR NOT. UNDER NO CIRCUMSTANCES SHALL SELLER’S LIABILITY TO BUYER EXCEED THE ACTUAL SALES PRICE OF THE PRODUCTS PROVID-ED HEREUNDER. No representative is authorized to assume for Seller any other liability in connection with the products.One Year Limited Warranty Industry Certifi cations/Registration Numbers NVRCSI-CPBRW-CP, NVRCSI-CPBRW-AW UL - Power Supply: UL60950-1
-30-IndexAAC Current 6AC Power Frequency 6AC Power Speci• cations 6Acronyms and De• nitions 5AC Voltage 6Additional Tips 27Application 4Auto Shutdown Enable 26Auto Shutdown Threshold 26BBox Weight 6CChannel Frequency Numbers 25Composite Transmit Power 26Control Parameter Details 24Co-Pilot Beacon Con• guration 20Co-pilot beacon Per Channel Transmit Power 26DDepth 6Detected Power 26Detected RF Power Shutdown 24EEIA232 Pin Speci• cations 12Environmental Requirements 6Explosive Atmospheres 4FFunctional Overview: 6GGrounding 4HHeight 6IImportant Installation Notes 11Industry Certi• cations/Registration Numbers 29KKey Features 24LLightning Danger 4Limited Warranty 29Local Communication Interface Ports 11Login 15MMain Menu 15Manual Shutdown 26Master Shutdown 24Mechanical Drawing 7Mechanical Speci• cations 6Monitoring & Alarms 12Multiple Beacon Con• guration 24NNetworking Con• guration 22null modem adapter 13OOptional Accessories 11PPN Offset 26Powering Up the Unit 11Power supply cable connectors 11Product Introduction 5Product Registration Information 4RRelative Humidity 6Sserial cable 13Set Parameters Menu 16, 19Signal Transmit Enables 25Surface Coating 6System Commands 23System Con• guration 21System Set-Up Considerations 7TTau (Delay Correction) 26TCP/IP settings 27Telnet Session 16Telnet Session (Remote Access) 16Temperature Range 6terminal emulation programs 14Text Menu Interface 13Thermal Management 6Timing Reference Selection 24Timing Reference Source 24Transmitter Con• guration 20UUL - Power Supply 29USB Interface 12User Interface 15WWarranty 29Web based GUI Session 13Width 6
-31-Notes
Notes
Notes
Notes
Notes
960-1146-002 rev 004

Navigation menu