Whirlpool XPSG ECM Wireless Module User Manual CONNECTED APPLIANCE INFORMATION

Download:
Mirror Download [FCC.gov]
Document ID	1694434
Application ID	E39rpSoSAspg0Fkn+gy7AA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.6kB (120033 bits)
Date Submitted	2012-05-10 00:00:00
Date Available	2012-05-10 00:00:00
Creation Date	2012-04-03 17:51:12
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2012-04-03 17:51:12
Document Title	CONNECTED APPLIANCE INFORMATION
Document Creator	Microsoft® Office Word 2007
Document Author:	Wallace J. Elston

CONNECTED APPLIANCE INFORMATION
Federal Communications Commission (FCC) Compliance Notice
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user‟s authority to operate the equipment.
RF Exposure Information
To comply with FCC/IC RF exposure requirements for mobile transmitting devices, this
transmitter should only be used or installed at locations where there is at least 20cm separation
distance between the antenna and all persons.
To comply with FCC/IC RF exposure limits for general population/uncontrolled exposure, the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter
CONNECTED APPLIANCE INFORMATION
Industry Canada (IC) Compliance Notice
This Device complies with Industry Canada License-exempt RSS standard(s). Operation is
subject to the following two conditions:
1. This device may not cause interference,
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.
To comply with FCC and Industry Canada RF radiation exposure limits for general population,
the antenna(s) used for this transmitter must be installed such that a minimum separation
distance of 20 cm is maintained between the radiator (antenna) and all persons at all times and
must not be co-located or operating in conjunction with any other antenna or transmitter.
Le présent appareil est conforme aux CNR d„Industrie Canada applicables aux appareils radio
exempts de licence. L„exploitation est autorisée aux deux conditions suivantes:
(1) l„appareil ne doit pas produire de brouillage, et
(2) l„utilisateur de l„appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d„en compromettre le fonctionnement.
Conformément à la réglementation d„Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d„un type et d„un gain maximal (ou inférieur) approuvé pour
l„émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l„intention des autres utilisateurs, il faut choisir le type d„antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l„intensité nécessaire à
l„établissement d„une communication satisfaisante.
Pour satisfaire aux exigences de la FCC et IC d‟exposition aux radiofréquences, une distance de
séparation de 20 cm ou plus doit être maintenue entre cet appareil et des personnes lors de
fonctionnement du dispositif. Pour assurer la conformité des opérations au plus près que cette
distance n‟est pas recommandée. L‟antenne utilisée pour ce transmetteur ne doit pas être colocalisés en conjonction avec toute autre antenne ou transmetteur.
CONNECTED APPLIANCE INFORMATION
OEM Responsibilities to comply with FCC and Industry Canada Regulations
The XPSG Module has been certified for integration into products only by OEM
integrators under the following conditions:
1. The antenna(s) must be installed such that a minimum separation distance of 20cm is
maintained between the radiator (antenna) and all persons at all times.
2. The transmitter module must not be co-located or operating in conjunction with any
other antenna or transmitter.
As long as the two conditions above are met, further transmitter testing will not be required.
However, the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital device
emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for certain
configurations or co-location with another transmitter), then the FCC and Industry Canada
authorizations are no longer considered valid and the FCC ID and IC Certification Number
cannot be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a
separate FCC and Industry Canada authorization.
End Product Labeling
The XPSG Module is labeled with its own FCC ID and IC Certification Number. If the FCC ID
and IC Certification Number are not visible when the module is installed inside another device,
then the outside of the device into which the module is installed must also display a label
referring to the enclosed module. In that case, the final end product must be labeled in a visible
area with the following:
“Contains Transmitter Module FCC ID: A5UXPSG”
“Contains Transmitter Module IC: 10248A-XPSG”
or
“Contains FCC ID: A5UXPSG”
“Contains IC: 10248A-XPSG”
The OEM of the XPSG Module must only use the approved antenna(s), which have been
certified with this module. The OEM integrator has to be aware not to provide information to
the end user regarding how to install or remove this RF module or change RF related
parameters in the user manual of the end product.
The user manual for the end product must include the following information in a
prominent location:
“To comply with FCC and Industry Canada RF radiation exposure limits for general population,
the antenna(s) used for this transmitter must be installed such that a minimum separation
distance of 20cm is maintained between the radiator (antenna) and all persons at all times and
must not be co-located or operating in conjunction with any other antenna or transmitter.”

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
Language                        : en-US
Tagged PDF                      : Yes
Title                           : CONNECTED APPLIANCE INFORMATION
Author                          : Wallace J. Elston
Creator                         : Microsoft® Office Word 2007
Create Date                     : 2012:04:03 17:51:12
Modify Date                     : 2012:04:03 17:51:12
Producer                        : Microsoft® Office Word 2007

EXIF Metadata provided by EXIF.tools