WiSilica WCD2CS WCD2CS User Manual WCD2CS Ver1 080918 rev1 0x
WiSilica, Inc. WCD2CS WCD2CS Ver1 080918 rev1 0x
WiSilica >
User manual
WISILICA NETWORK LIGHTING | CONTROL SERIES Table of Contents 1. Block Diagram..................................................................................................................................................... 3 2. Specifications ....................................................................................................................................................... 3 3. Device Dimensions (mm) ................................................................................................................................ 4 4. Connector Description ........................................................................................................................................ 5 5. Wiring Diagram .................................................................................................................................................. 5 6. Use Cases .............................................................................................................................................................. 5 7. User Precautions ................................................................................................................................................ 6 WISILICA NETWORK LIGHTING | CONTROL SERIES 1. Block Diagram 2. Specifications Symbol Min Input Voltage Vin 12 Input Current Iin1 Electrical Typ. 10 Max. Unit. Remarks 24 Vdc Rated Input voltage 15 mA @24Vdc, Max RF transmitting Analogue Dimming Output Dimming Output1 Vadimo1 10 Max output tolerance ±5% Dimming Output2 Vadimo2 10 Max output tolerance ±5% 15 mA For dimming max output 100 Output Current Dimming Range Dimming Resolution Dimming Curve Linear Cut Off Voltage WISILICA NETWORK LIGHTING | CONTROL SERIES bit 100 steps Programmable Bluetooth Frequency Range 2400 TX Power 2483.5 MHz dBm Conductive dF2 Frequency Drift(Max) -25 25 kHz Frequency Deviation ±225 ±275 kHz 150 kHz 48 mA 2483 kHz -37 mA -75 dBm Max. Unit. Carrier Frequency offset 30 TX current Receive Frequency 2400 Rx Current Receiver Sensitivity -86 Symbol Min Ambient Temperature ta -20 50 ºC Storage Temperature ts -20 70 ºC 85 Environmental Typ. Relative Humidity IP Rating Dimensions Net Weight Dimming Dimming Control 1 80 Type 0 – 10V 3. Device Dimensions (mm) Case Material : 5VA WISILICA NETWORK LIGHTING | CONTROL SERIES Note Analog Total current@ Max Tx power Total Current @Rx Mode Remarks IP20 Indoor use only 66*47*29 mm L x W x H (mm) 90 100 T.B.D 4. Wire Description PIN SYMBOL COLOR DESCRIPTION CH1+ Purple CH1 0 to 10V Analog Output CH2+ Blue CH2 0 to 10V Analog Output GND Grey 12V Ground 12V Red 12V(Input) 5. Wiring Diagram 6. Use Cases 1. Controlling Intensity and CCT of LED bulb WISILICA NETWORK LIGHTING | CONTROL SERIES 2. Controlling LED bulb with Sensor Inputs 7. User Precautions • Observe the correct polarity of output terminal. • Avoid input voltage exceeds the maximum rating, which will cause damage to the circuit and result in malfunction • Static electricity or surge voltage may damage the components inside LED Driver, to avoid this please follow the proper anti-electrostatic working process. 8. FCC Statement • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: WISILICA NETWORK LIGHTING | CONTROL SERIES • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. • Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. • This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • • RF Exposure Information • The device has been evaluated to meet general RF exposure requirement. The device can be use d in portable exposure condition without restriction. WISILICA NETWORK LIGHTING | CONTROL SERIES
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Author : Admin Create Date : 2018:08:09 12:43:58Z Modify Date : 2018:10:25 18:26:04+08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : Admin Title : Microsoft Word - WCD2CS Ver1_080918_rev1.0.docx Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2018:10:25 18:26:04+08:00 Producer : GPL Ghostscript 8.15 Document ID : uuid:ac0d07ca-2e47-4c60-b53e-9f9c20e3e147 Instance ID : uuid:480224d6-4b1f-4bc7-accd-8aa6d3cfa0ce Page Count : 7EXIF Metadata provided by EXIF.tools