Wilson Electronics 271201SA WIRELESS DUAL-BAND AMPLIFIER User Manual AIG 110726 SOHO 11 26 08 indd

Wilson Electronics, LLC WIRELESS DUAL-BAND AMPLIFIER AIG 110726 SOHO 11 26 08 indd

Contents

SOHO INSTALLATION GUIDE

AmplifierAmplifierInstallationGuidestallatiostallatSOHO WirelessDual-BandCellular / PCSAmplifi erContents:Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1Antenna Options · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2How It Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 3Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3Installation Overview · · · · · · · · · · · · · · · · · · · · · · · · · · · 3Installing the Outside Antenna · · · · · · · · · · · · · · · · · · · 4Installing the Inside Antenna · · · · · · · · · · · · · · · · · 5Installing the Amplifi er · · · · · · · · · · · · · · · · · · · · · · · · · · 6Powering up a Wilson Amplifi er · · · · · · · · · · · · · · · · · · · 7Understanding the Amplifi er Lights · · · · · · · · · · · · · · · · · 8Warnings and Recommendations · · · · · · · · · · · · · · · · · · 9About Wilson Electronics · · · · · · · · · · · · · · · · · · · · · · · · 10Amplifi er Specifi cations · · · · · · · · · · · · · · · · · · Back CoverWilson® Electronics, Inc.Warning: This manual contains important safety and operating information. Please read and follow the instructions in this manual. Failure to do so could be hazardous and result in damage to your amplifi er.!
130-Day Money-Back GuaranteeAll Wilson Electronics products are protected by Wilson’s 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase.1-Year WarrantyWilson Electronics amplifi ers are warranted for one (1) year against defects in workmanship and / or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Amplifi ers may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer.This warranty does not apply to any amplifi ers determined by Wilson Electronics to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.RMA numbers may be obtained by phoning Technical Support at 866-294-1660.Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.Disclaimer: The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no responsibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.Copyright © 2007 Wilson Electronics, Inc. All rights reserved.
2Installation Instructions for the Following Wilson Amplifi ers:SOHO Wireless Dual-Band Cellular/PCS Amplifi erModel # 271201, Part # 803245FCC ID: PWO271201SA IC: 4726A-271201SAThe term “IC” before the radio certifi cation number only signifi es that Industry Canada technical specifi cations were met. Model # 271201, Part # 803245Inside this Package• SOHO wireless amplifi er• AC 120 volt power supplyAdditional Required Equipment (sold separately)• Outside antenna• Inside antenna• Antenna coax cableA 13 dB 800 MHz Yagi Cellular Antenna (301111) B 1900 MHz Yagi PCS Antenna (301124)C 800 MHz Yagi Cellular Antenna (301129) D Dual-Band Panel Antenna (301135)E Dual-Polarity Dome Antenna (301123) F Dual-Band Dome Antenna (301121) G Low Profi le Cellular Antenna (301106) H Mini Magnet-Mount Antenna (301103)I Magnet-Mount Antenna (301113)J Dual-Band Trucker Antenna (301101)Antenna OptionsABCDEFGHJ120 V AC plug-inpower supplySOHO wirelessamplifi erI(outside)(outside)(outside)(inside or outside)(inside) (inside)(inside) (inside)This Amplifi er is Authorized for use with any of the illustrated antennas.
3How it WorksYour new Wilson SOHO Wireless Dual-Band Amplifi er has been carefully engineered to enhance the performance of your cell phone or cellular data card in small offi ce/home offi ce applications. Its advanced technology is designed to signifi cantly improve voice and data signal quality and reduce disconnects and drop-outs. The amplifi er works with two antennas (sold separately): one communicates with the cell site (the outside antenna) and the other communicates with your cell phone or laptop data card (the inside antenna).The outside antenna will collect the outside signal and send it through a cable to the amplifi er. The signal is then boosted and sent through a cable to the inside antenna, which communicates with your cell phone or data card. When the cell phone or data card transmits, the inside antenna picks up the signal and sends it to the amplifi er where it is boosted and sent through the outside antenna to the cell site.Wilson Electronics manufactures a wide variety of antennas and accessories to help you customize your SOHO Wireless Dual-Band Amplifi er for your specifi c application (see page 2). Contact your dealer or visit www.wilsonelectronics.com.Before Getting StartedThis guide will help you properly install Wilson’s SOHO Wireless Dual-Band Amplifi er. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment. If you do not understand the instructions in full, please contact Wilson Technical Support at 866-294-1660.Installation OverviewThe following steps provide a summary of the amplifi er/installation process using a Yagi antenna as the outside antenna and a panel antenna as the inside antenna. However, they are not a substitute for the complete installation instructions on the following pages, which you should read thoroughly. Be sure to read and follow the instructions that come with your specifi c antennas.STEP 1 Install the Outside AntennaMount the Yagi antenna to a fi xed location (such as a pole) on the roof of your building. Be sure it is pointing toward the nearest cell tower and away from where you plan to install the inside antenna. IMPORTANT: The outside antenna must have a separation of at least 48 inches (122 centimeters) from all persons during normal operation.STEP 2 Install the Inside AntennaAttach the panel antenna as close as possible to the center of the area where the signal needs to be amplifi ed. Ensure there is a minimum separation of 20 feet between the outside and inside antennas. IMPORTANT: The inside antenna must have a separation of at least 8 inches (20 centimeters) from all persons during normal operation.STEP 3 Install the Amplifi erPosition the amplifi er in a well-ventilated location near a power outlet. Attach the antennas to the amplifi er using 50-ohm or equivalent coax cable (available in different lengths from Wilson Electronics).STEP 4 Power up the Amplifi erIMPORTANT! Before connecting the power supply, ensure that both the inside and outside antenna cables are connected. Also ensure that all cell phones and cellular data cards within 20 feet (6 meters) of the inside antenna are turned off. Plug the supplied 6-volt power supply into the amplifi er and then into a wall outlet.
4Installing the Outside AntennaThe antenna that communicates with the cell site should be mounted on the outside of the building—this is the preferred location and will give the best performance. Alternatively, locating this antenna inside the building near a window will also work under certain conditions. IMPORTANT: The outside antenna must have a separation of at least 48 inches (122 centimeters) from all persons during normal operation.Outdoor InstallationFor best results, use a Wilson Yagi antenna that is compatible with the frequency of your cellular service provider. A dual-band trucker antenna will also work. Mount the antenna as high as possible on your building for optimum signal reception and transmission.Follow the specifi c installation instructions included with the outside antenna. Lightning protection is recommended for all outdoor antenna installations. Take extreme care to ensure neither you nor the antenna come in contact with any electrical power lines. Ensure there are three feet of clearance in all directions surrounding the antenna.Alternate InstallationIf you choose to install the outside antenna indoors, select a location near a window or glass door where you have the strongest existing cell signal. (See the illustration on page 5.) Follow the specifi c installation instructions included with the antenna.Cell Tower RF SignalYagi Outside AntennaWarning: The outside antenna must be installed with a separation of at least 48 inches (122 centimeters) from all persons during normal operation.!NOTCORRECTWarning: Never point the front of the Yagi antenna toward the inside antenna - oscillation will result, causing an amber light on the amplifi er and gain reduction.!Pointing toward cell towerCORRECT
5Installing the Inside AntennaThe antenna that communicates with your cell phone or cellular data card should be installed in the center of where the signal needs to be amplifi ed. Wilson’s magnet-mount, mini magnet-mount, dome and panel antennas will work well with the SOHO Wireless Amplifi er.20 feet (6.10 meters) minimum separation between inside antenna and outside antennaAmplifi er Outside AntennaInside AntennaIn the above illustration, Wilson mini magnet-mount antennas are being used for both the outside antenna (on the window) and the inside antenna (on the desk). Follow the specifi c instructions included with the antennas for your specifi c application.Warning: The inside antenna must have a separation distance from all persons that is at least 8 inches (20 centimeters).!Warning: Connecting the amplifi er directly to the cell phone with use of an adapter will damage the cell phone.!
6Installing the Amplifi erSelect a location to install the amplifi er that is away from excessive heat, direct sunlight, moisture and that has proper ventilation. Do not place the amplifi er in an air-tight enclosure.Recommended installation locations are:• On a desk or table top• In a bookshelf• On the fl oorIn the illustration below, a Wilson Yagi antenna is being used as the outside antenna, and a Wilson dome antenna is being used as the inside antenna.Run the outside antenna cable to the amplifi er and attach it to the FME-male connector labeled “outside antenna” on the amplifi er. Run the inside antenna cable to the amplifi er and attach it to the FME-male connector labeled “inside antenna” on the amplifi er.Note: Be careful when plugging the connectors in so as not to damage the center pin.Connect the outside antenna to the amplifi er with 50-ohm or equivalent coax cable (available in different lengths from Wilson Electronics). Place the inside antenna in the center of the area needing the amplifi ed signal. It is important to have at least 20 feet (6.1 meters) of separation between the inside and outside antennas. Closer spacing may result in oscillation, which will cause the amplifi er to automatically reduce its gain.AC/DCPower SupplyAmplifierSupportsMultipleUsersInside AntennaOptional DomeAntenna ShownPoint Yagi antenna away from cell phone antennaOutsideAntennaOptional1900 MHzYagiAntennaShown20 feet (6.1 meters) minimum separation between insideand outside antennaAntenna Separation
7Powering up a Wilson Amplifi er1. IMPORTANT! Ensure that all cell phones and cellular data cards within 20 feet (6.1 meters) of the inside antenna are turned off.2. To verify proper installation of the amplifi er and antennas, make sure that the distance between the inside and outside antennas is a minimum of 20 feet (6.1 meters).3. If you are using an Yagi antenna as a outside antenna, never point the front of the Yagi toward the inside antenna.4. Ensure that both the outside antenna coax cable and the inside antenna coax cable are connected to the amplifi er before powering up the amplifi er.5. Plug the power supply into the amplifi er input marked “power” (carefully, to avoid damaging the center pin) and then into a wall outlet.Warning: Verify that both the outside antenna and the inside antenna are connected to the amplifi er before powering up the amplifi er.!Warning: Use only the power supply provided in this package. Use of a non-Wilson product may damage your equipment.!NOTE: The aluminum casing of a Wilson amplifi er will adjust very quickly to the ambient temperature of its environment. For example, in the summer, when the attic of a house can easily exceed 100 degrees Fahrenheit (38 degrees Celsius), the amplifi er temperature may be higher. The casing will be hot to the touch. Such high temperatures will not damage the amplifi er, nor do they pose a fi re risk. As recommended in these instructions, install the amplifi er in a location with adequate ventilation. Keep the area free of items that could block air fl ow to the amplifi er.
8Understanding the Amplifi er LightsThe power light PWR will turn green when the amplifi er is successfully powered up. When the 800 MHz or 1900 MHz lights are lit green, the amplifi er is amplifying the outside signal.If one or both frequency lights turn red, oscillation is occurring and the amplifi er has powered down. The outside antenna needs to be moved farther from the inside antenna. Move the outside antenna on the roof of the car to the rear of the car, but at least 8-12 inches from the rear or side windows. Remove power from the amplifi er and reinstall power. This resets the amplifi er.If the lights are now green, the oscillation has stopped and the amplifi er is working. If the red light is still on, move the antenna farther away and repeat the process.Always use a magnet-mount or roof-mount antenna. Do not use a glass-mount antenna, as oscillation may cause continuous shut-down of the amplifi er.An amber light in either the 800 MHz or 1900 MHz position indicates overload from the cell site. The amplifi er has temporarily shut down and will automatically reset.
9Warnings and Recommendations Warning: A Yagi antenna must always be located so the back or side points to the inside antenna. Never point the front of the Yagi antenna toward the inside antenna – oscillation will result, causing amber light and gain reduction. Warning: Connecting the amplifi er directly to the cell phone with use of an adapter will damage the cell phone. Warning: Connect both the outside and inside antenna cables to the amplifi er before powering up the amplifi er. Warning: Use only the power supply provided in this package. Use of a non-Wilson product may damage your equipment. Warning: The outside antenna must have a separation distance from all persons that is at least 48 inches (122 centimeters). The inside antenna must have a separation distance from all persons that is at least 8 inches (20 centimeters).Lightning protection is recommended for all in-building installations using an outside antenna.
10About Wilson ElectronicsWilson Electronics, Inc. has been a leader in the wireless communications industry for nearly 40 years. The company designs and manufactures amplifi ers, antennas and related components that signifi cantly improve cellular telephone signal reception and transmission in a wide variety of applications, both mobile and in-building.With extensive experience in antenna and amplifi er research and design, the company’s engineering team uses a state-of-the-art testing laboratory, including an anechoic chamber and network analyzers, to fi ne-tune antenna designs and performance. For its amplifi ers, Wilson uses a double electrically insulated RF enclosure and outside simulators for compliance testing.Wilson amplifi ers feature Smart Technology™ that enables them to automatically adjust their power based on cell site requirements. By preventing oscillation, signal overload and interference with other users, these Smart Technology™ amplifi ers improve network cell phone areas without compromising the carrier’s system.All products are engineered and assembled in the company’s 50,000-square-foot headquarters in St. George, Utah. Wilson has product dealers in all 50 states as well as Canada and Mexico, Central and South America.
Wilson® Electronics, Inc.Phone: 866-294-1660 www.wilsonelectronics.com Fax: 435-656-2432Part # AIG 110726 - SOHO / 11.26.08Amplifi er Specifi cationsDual Band800/1900 MHz Specifi cationsModel Number / Part Number 271201 / 803245Connectors N-Type FemaleImpedance (input/output) 50 ohmsDimensions 5.6 x 3.6 x 1.7 inch or 14.2 x 9.1 x 4.4 cmWeight 1.2 lbs or 0.54 kgFrequency 824-894 MHz / 1850-1990 MHz1Passband Gain (nominal)55 dB220 dB Bandwidth (nominal)800 MHz 31 MHz1900 MHz 72 MHzPower output for single inside (uplink) 800 MHz 1900 MHzCDMA 34.5 dBm 33.6 dBmGSM 30.1 dBm 27.7 dBmEDGE 29.7 dBm 28.8 dBm3Power output (uplink) for multiple cell phones: Number ofcell phonesMaximum Power800 MHz 1900 MHz2 23.2 dBm 24.9 dBm3 19.7 dBm 21.4 dBm4 17.2 dBm 18.9 dBm5 15.2 dBm 17.0 dBm6 13.7 dBm 15.4 dBmPower output for single received channel(downlink) 800 MHz 1900 MHzCDMA 11.3 dBm 12.0 dBmGSM 9.3 dBm 10.4 dBmEDGE 8.8 dBm 9.2 dBm4Power output for multiple received channels (downlink). The maximum power is reduced by the number of channels: Number of channelsMaximum Power800 MHz 1900 MHz2 9.6 dBm 9.6 dBm3 6.1 dBm 6.0 dBm4 3.6 dBm 3.5 dBm5 1.6 dBm 1.6 dBm6 0.1 dBm 0.0 dBmNoise Figure (typical) 3.5 dB nominalIsolation (uplink/downlink) > 90 dBPower Requirements 120 V AC, 0.1 ANotes:1. Nominal gain is the maximum gain at any frequency in the passband.2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplifi cation is 20 dB lower than the passband amplifi cation. One of the frequencies is lower than the passband and the other is higher.3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB for each doubling of the number of signals.

Navigation menu