Wilson Electronics 460030 In-Building Cellular Signal Booster with In-Line Amplification User Manual
Wilson Electronics, LLC In-Building Cellular Signal Booster with In-Line Amplification
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3355835 |
| Application ID | 97DCYhor/qgwFu+asXsgDw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 303.02kB (3787754 bits) |
| Date Submitted | 2017-04-12 00:00:00 |
| Date Available | 2017-04-14 00:00:00 |
| Creation Date | 2017-03-02 14:09:41 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2017-03-02 14:10:09 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CC 2015 (Windows) |
A Wilson Electronics Brand WILSON PRO 1050 In-Building Cellular Signal Booster With In-Line Amplification User Manual NEED HELP? wilsonpro.com 866.294.1660 _____ Index Package Content About The WilsonPro 1050 System Key Features Competitive Advantages Post Install Setup 1050 Main Status Screen 1050 In-Line Status Screens 10 Safety Guidelines 12 Warranty 17 ________ Package Content Kit 460230 WilsonPro 1050 Two-Part Booster System 100’ Wilson 400 Cable Wide Band Directional Antenna + 75’ Wilson 400 Cable Pair of 2-Way Radios 2’ Wilson 400 Cable Dome Antenna + 100’ Wilson 400 Cable Lightning Surge Protector WILSON PRO 1050 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION WilsonPro 1050 System FCC Approved In-Line Amplification Compensates for up to 300’ of indoor cable losses using in-line amplification. Onboard Software For Better Control Automatically controlled with onboard software, ensuring great connectivity throughout large spaces and multi-story buildings. Extended Dynamic Range For Continuous Connectivity XDR allows the booster system to never shutdown due to too strong of a signal. No matter how strong, the booster system will never overpower and shutdown. Auto-Calibration Main booster & In-Line booster automatically link, communicate & calibrate. IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION WILSON PRO 1050 In-Line Amplification The WilsonPRO 1050 Cellular Signal Booster System automatically compensates for signal loss resulting from a long indoor RF coax cable run. Simply connect the 1050 In-Line unit at a cable length between 100’ and 300’ from the 1050 Main unit. When both units are powered up, they will begin to communicate with each other, sending signals and calculating the amount of signal loss in the cable. Once cable losses are calculated, the gain levels are adjusted between the 1050 Main and 1050 In-Line units so that only enough extra gain is added to the system to compensate for the signal loss of the indoor cable. This capability to overcome significant cable losses allows the 1050 System to provide cellular coverage in areas that were previously impossible, such as the lower floors of residences. The WilsonPro 1050 system also includes Wilson Electronics’ state-of-the-art XDR (Extended Dynamic Range) technology that prevents signal overload conditions which can, in accordance with FCC regulations, force a booster to shut down or even shut down. When the WilsonPro 1050 system senses that any incoming cell signal is too strong, and threatens to overload the system, XDR automatically reduces signal gain to compensate for this overload condition while maintaining signal coverage throughout the building. In contrast, competing signal boosters shut down when they reach a maximum incoming signal strength threshold, causing the indoor cell signal to drop out. Both antenna ports are located on the top of the 1050 Main unit for easy installation. Like all WilsonPro cell signal boosters, the WilsonPRO 1050 Cellular Signal Booster System is universal: it works for all cellular devices, all services including 4G LTE, and all U.S. and Canada cell phone carriers. WILSON PRO 1050 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION ____________ Key Features FCC Approved In-Line Amplification: Compensates for up to 300’ of indoor cable losses using in-line amplification, providing cell coverage to hard-to-reach areas. Onboard Software for Better Control: Booster is automatically controlled with automatic onboard software. The booster will adjust its gain level up or down as required by the conditions of the immediate signal environment. Extended Dynamic Range (XDR) for continuous connectivity: Gives the 1050 much greater tolerance for a strong incoming signal from the tower. XDR lets the 1050 system work with an incoming signal stronger than any competing booster and never shuts down due to a strong outside signal. Automatic Calibration: Main booster and In-Line booster automatically link, communicate, and calibrate. IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION WILSON PRO 1050 ___________ Competitive Advantages Highest Downlink Power: Up to +15dB more downlink power than the competition allows for stronger signal in environments where the incoming signal is weak. The benefit is a stronger signal sent to the inside antennas, providing larger coverage area from a single booster. Highest Uplink Power: This allows for a stronger signal transmitted to the tower, up to +3dB more than the competition, providing greater user capacity and increased range from the cell site. Lower Overload and Shutdown Threshold: No matter how strong the outside signal, the WilsonPro 1050 system never shuts down. This is a huge benefit in strong signal environments like cities and locations close to a carrier tower. Intelligent Control: WilsonPro cellular boosters automatically adjust signal gain while still providing even signal coverage throughout the building. Sophisticated Software: Cellular signals are constantly fluctuating. The software is always monitoring signal levels and making immediate adjustments as needed, allowing the booster to operate at maximum gain consistently. WILSON PRO 1050 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION __________ Installation Diagram A Wilson Lightning Surge Protector is recommended for all building installations. Make sure the protector is installed outside the building at point of entry connected to a suitable ground and in line between the Outside Antenna and the Signal Booster. Outside Directional Antenna Lightning Surge Protector 1050 In-Line Inside Dome Antenna 1050 Main to power BAND SELECT RESET CABLE LOSS The direction of the outside antenna should be adjusted until the “DL” bar is maximized. 2-way radios are included to help with the installation process. Simple wall-mount installation. IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION WILSON PRO 1050 __________ Post Install Setup Outside Antenna The WilsonPRO 1050 System is designed with advanced internal programming, which allows it to automatically adjust for a variety of conditions, while Lightning Surge Protector still boosting weak signals. Once the AC power cable and antenna cables are connected, turn the unit on by toggling the power switch located near the AC power receptacle. 1050 In-Line (placed at a cable length of 100’ to 300’) Inside Antenna to power 1050 Main to power WILSON PRO 1050 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION ____________ 1050 Main Status Screen Upon power up, the 1050 MAIN unit will attempt to begin it’s calibration routine, which lasts approximately 14 seconds during which time one of the following messages will appear on the screen: BAND SELECT Boot Screen RESET BAND SELECT BAND SELECT CABLE LOSS RESET RESET BAND SELECT BAND SELECT In-Line Found Screen CABLESELECT LOSS BAND CABLE LOSS RESET BAND SELECT CABLE LOSS RESET RESET The 1050 In-Line unit has been found BAND SELECT RESET CABLE LOSS and is communicating with the 1050 Main.CABLE Cable loss calibration is in LOSS progress. RESET BAND SELECT BAND SELECT CABLE LOSS CABLE LOSS BAND SELECT RESET RESET BAND SELECT No In-Line Screen CABLE LOSS CABLE LOSS RESET RESET BAND SELECT CABLE LOSS RESET CABLE LOSS CABLE LOSS The 1050 In-Line unit has been found and is communicating with the 1050 Main. Cable loss calibration is in progress. BAND SELECT BAND SELECT RESET RESET BANDWITH SELECTIN-LINE AMPLIFICATION IN-BUILDING SIGNAL BOOSTER CABLE LOSS CABLE LOSS RESET WILSON PRO 1050 BAND SELECT RESET ________ CABLE LOSS BAND SELECT 1050 Main Status Screen (cont.) RESET BAND SELECT BAND SELECT Failed Calibration Screen CABLE LOSS RESET RESET Failed cable loss calibration. Cable loss must be between 4dB and CABLE LOSS25dB for all bands. If the cable loss is calculated to be outside of this range, calibration will fail. This range correspondsBAND SELECT between 100 feet and 300 feet of Wilson 400 Cable. BAND SELECT CABLE LOSS RESET BAND SELECT CABLE LOSS RESET BAND SELECT RESET Once cable calibration has successfully CABLE LOSS completed, the band status screens will appear. BAND SELECT CABLE LOSS BA ND CA RESET LE RE LO SE LE CT RESET BAND SELECT SE CABLE LOSS RESET BA ND BAND SELECT SE LE CT Cable Loss Button CA LE RE LO CABLE LOSS SE BA ND BAND SELECT CA LE RE LO RESET BAND SELECT BA ND CA LE RE LO SE LE CT CABLE LOSS CT Pressing the Cable Loss Button will display the cable loss compenstion at BA NDthe upper bands and lower bands. EL EC SE LE SE RESET SE CA LE RESET LO BAND SELECT RE SE CABLE LOSS BA ND RESET SE LE CT BAND SELECT ET WILSON PRO 1050 IN-BUILDINGRESET SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION BAND SELECT CABLE LOSS ____________ 1050 In-Line Status Lights The 1050 In-Line has 3 status lights: 1050 In-Line CABLE CAL COM STATUS 1050 In-Line CABLE CAL COM STATUS ‘STATUS’ LED: GREEN: Normal 1050 In-Line CABLE CAL COM STATUS 1050 In-Line CAL COM ORANGE: One or moreCABLEbands has shut off due to strong downlink. RED: One or more bands has shut off due to OSCILLATION. TATUS 10 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION 1050 In-Line WILSON PRO 1050 STATUS BLE CAL ________ 1050 In-Line CABLE CAL COM 1050 In-LIne Status Screen (cont.) STATUS 1050 In-Line CABLE CAL COM STATUS ‘COM’ LED: GREEN: Normal, waiting for next communications event 1050 In-Line CABLE CAL COM STATUS ORANGE: Brief orange blink when 1050 In-Linewith 1050 Main. communicating 1050 In-Line COM STATUS CABLE CAL COM STATUS RED: Communications failure when attempting to communicate with 1050 Main. ‘CABLE CAL’ LED: GREEN: Calibration complete. 1050 In-Line CABLE CAL COM STATUS 1050 In-Line CABLE CAL COM STATUS ORANGE: Calibration in process. RED: Calibration failed. WILSON PRO 1050 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION 11 ______________ Safety Guidelines Warnings o uphold compliance with network protection standards, all active cellular devices must maintain at least 6 feet of separation distance from Panel and Dome antennas. Use only the power supply provided in this package. Use of a non-Wilson Electronics product may damage your equipment. The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than 100 degrees Fahrenheit). It is not intended for use in attics or similar locations subject to temperatures in excess of that range. RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons. AWS Warning: Warning: The Outside Antenna must be installed no higher than 10 meters (31’9”) above ground. This is a CONSUMER device. BEFORE USE, you meet all requirements set out in CPC-2-1-05. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC, ISED or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. This device may be operated ONLY in a fixed location for in-building use. This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment. FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS PROVIDER, PLEASE SEE BELOW: Sprint: http://www.sprint.com/legal/fcc_boosters.html T-Mobile/MetroPCS: https://support.t-mobile.com/docs/DOC-9827 Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html AT&T: https://securec45.securewebsession.com/attsignalbooster.com/ U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp 12 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION WILSON PRO 1050 _________________ Antenna Kit Options The following accessories are certified by the FCC to be used with the Wilson PRO 1050 System. Inside Antenna Expansion Kit Kit 309900-50N40090 2 - Wall Panel antennas 1 - 50 ohm 3-Way Splitter 1 - 100' Wilson 400 Kit 309905-50N17420 3 - Wall Panel Antennas 3 - 2-Way 50 Ohm Splitters 20' RG174 Kit 309902-75F0650 2 - Wall Panel Antennas 1 - 3-Way 75Ohm Splitter 50' RG6 Kit 309903-75F1180 3 - Wall Panel Antennas 3 - 2-Way 75Ohm Splitters 80' RG11 cable Kit 309904-75F5830 1 - Wall Panel Antenna 1 - 2-Way 75 Ohm Splitter 30' RG58 cable Inside Antenna Kits Kit 311155-0670 75 Ohm Wall mount Panel Antenna 70’ RG6 Cable Kit 311135-5840 50 Ohm Wall mount Panel Antenna 40’ RG58 Cable Kit 311135-400150 50 Ohm Wall mount Panel Antenna 150' Wilson 400 Kit 311155-11120 75 Ohm Wall mount Panel Antenna 10’ RG11 cable Kit 304412-400100 50 Ohm 4G Dome Antenna 100' Wilson400 cable Kit 304412-5830 50 Ohm 4G Dome Antenna 30' RG58 cable Kit 304419-1175 75 Ohm 4G Dome Antenna 75' RG 11 cable Kit 304419-17450 75 Ohm 4G Dome Antenna 50' RG174 cable May need separate adapter Kit 304419-0650 75 Ohm 4G Dome Antenna 50' RG6 cable 50 Ohm Outside Antenna Kits Kit 314453-5825 50 Ohm Pole Mount Panel Antenna 25’ RG58 Cable Kit 314411-5825 50 Ohm Wide Band Directional 25’ RG58 Cable Kit 301111-5850 Yagi Directional Antenna 50’ RG58 Cable Kit 311203-5820 Omni-Directional antenna 20’ RG58 Cable Kit 314411-40075 50 Ohm Wide Band Directional 75’ LMR400 Cable Kit 311203-40020 Omni-Directional antenna 20’ LMR400 Cable Kit 301111-400170 Yagi Directional w/ N-Female 170’ LMR400 Kit 314453-40075 50 Ohm Pole Mount Panel Antenna 75’ LMR400 Cable Kit 304422-40020 50 Ohm 4G Omni Antenna 20’ Wilson400 cable Kit 304422-5810 50 Ohm 4G Omni Antenna 10’ RG58 cable Kit 304422-1120 50 Ohm 4G Omni Antenna 20’ RG11 cable May need separate adapter Kit 311141-0620 75 Ohm Grey Brick Antenna 20’ RG6 Cable Kit 301111-11140 Yagi Directional Antenna 140’ RG11 Cable N-Male to F-Female adapter Kit 311201-1120 Omni Directional w/ F-Female 20’ RG11 Cable Kit 314473-1175 75 Ohm Pole Mount Panel Antenna 75’ RG11 Cable Kit 314475-0630 75 Ohm Wide Band Directional 30’ RG6 Cable Kit 314475-1175 75 Ohm Wide Band Directional 75’ RG11 Cable Kit 311141-1120 75 Ohm Grey Brick Antenna 20’ RG11 Cable Kit 304421-17410 75 Ohm 4G Omni Antenna 10’ RG174 cable Kit 304421-0610 75 Ohm 4G Omni Antenna 10’ RG6 cable Kit 304421-5810 75 Ohm 4G Omni Antenna 10’ RG58 cable May need separate adapter Kit 304421-1120 75 Ohm 4G Omni Antenna 20’ RG 11 cable 75 Ohm Outside Antenna Kits Kit 301111-0675 Yagi Directional Antenna 75’ RG6 Cable N-Male to F-Female adapter Kit 311201-0620 Omni Directional w/ F-Female 20’ RG6 Cable Kit 314473-0640 75 Ohm Pole Mount Panel Antenna 40’ RG6 Cable WILSON PRO 1050 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION 13 ___________ Specifications Product Number 460030 Model Number 460030 FCC ID PWO460030 / PWO0460030IL IC ID 4726A-460030 Connectors N-Female Antenna Impedance 50 Ohms Frequency 698-716 MHz, 729-746 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Power output for single cell phone (Uplink) dBm 700MHz Band12/17 24.7 24.7 24.3 25.1 24.5 Power output for single cell phone (Downlink) dBm 700MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz 14.8 14.3 15.2 15 15.1 Noise Figure Isolation Power Requirements 700MHz Band13 800MHz 1700MHz 1050 Main 1050 In-Line 5 dB nominal 5 dB nominal > 90 dB > 90 dB 110-220V AC 5V 3A 1900MHz The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor. 14 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION WILSON PRO 1050 ____________ Notes WILSON PRO 1050 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION 15 ____________ Notes 16 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION WILSON PRO 1050 ________ Warranty 30 DAY MONEY-BACK GUARANTEE All WilsonPro products are protected by WilsonPro 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 3 YEAR WARRANTY WilsonPro Boosters are warranted for three (3) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by WilsonPro. WilsonPro shall, at its option, either repair or replace the product. This warranty does not apply to any Signal Boosters determined by WilsonPro to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties. RMA numbers may be obtained by contacting Customer Support. DISCLAIMER: The information provided by WilsonPro is believed to be complete and accurate. However, no responsibility is assumed by WilsonPro for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use. NEED HELP? support.wilsonpro.com 866.294.1660 WILSON PRO 1050 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION 17 A Wilson Electronics Brand A Wilson Electronics Brand 3301 East Deseret Drive, St. George, UT www.wilsonpro.com | support.wilsonpro.com Copyright © 2016 Wilson Electronics. All rights reserved. Wilson Electronics products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA 111853_Rev01_03.01.17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c123 79.158978, 2016/02/13-01:11:19 Create Date : 2017:03:02 14:09:41-07:00 Metadata Date : 2017:03:02 14:10:09-07:00 Modify Date : 2017:03:02 14:10:09-07:00 Creator Tool : Adobe InDesign CC 2015 (Windows) Instance ID : uuid:98a18067-d9c7-45c8-b3b6-6dae95c870d9 Original Document ID : xmp.did:1f27a136-e1bb-48c3-bdc5-a32b0d8df0cb Document ID : xmp.id:bed27ea1-1681-1d45-8dc0-b74efa803952 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:f96e792c-88f0-e044-8ecd-abf2318d8bb5 Derived From Document ID : xmp.did:62c1f756-776c-4244-9872-d52f11f8d62b Derived From Original Document ID: xmp.did:1f27a136-e1bb-48c3-bdc5-a32b0d8df0cb Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Windows) History Changed : / History When : 2017:03:02 14:09:41-07:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 20 Creator : Adobe InDesign CC 2015 (Windows)EXIF Metadata provided by EXIF.tools