Wilson Electronics 460035 Quint Band Bi-Directional Direct Contact Coupling Amplifier User Manual Revised
Wilson Electronics, LLC Quint Band Bi-Directional Direct Contact Coupling Amplifier Users Manual Revised
Users Manual Revised
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3496992 |
| Application ID | WdDHWWStrsFy51Or9axA9g== |
| Document Description | Users Manual Revised |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 453.66kB (5670692 bits) |
| Date Submitted | 2017-08-04 00:00:00 |
| Date Available | 2018-02-01 00:00:00 |
| Creation Date | 2017-07-10 14:58:24 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2017-07-26 15:12:08 |
| Document Title | Users Manual Revised |
| Document Creator | Adobe InDesign CC 2017 (Windows) |
A WILSON ELECTRONICS BRAND DRIVE SLEEK Vehicle Signal Booster Kit User Manual NEED HELP? support.weboost.com 866.294.1660 ______ Index Package Contents STEP 1: Mount Outside Antenna STEP 2: Route & Connect Booster STEP 3: Route Cable To Front Of Vehicle STEP 4: Connect System To Power STEP 5: Insert Phone Into Cradle Light Patterns Troubleshooting Safety Guidelines 11 Specifications 12 Warranty 14 ________ Package Contents Sleek Cradle Outside Antenna Signal Booster Power Supply DRIVE SLEEK CELL PHONE SIGNAL BOOSTER Magnetic Vent Mount (for cradle) ______ Step 1: Mount Outside Magnetic Antenna Identify a location on the top of your vehicle that is: • Near the center of the roof • At least 12 inches away from any other antennas • At least 6 inches away from any windows (including sunroofs) Clean the surface where you will place the outside antenna. Mount the outside antenna. 6 in. away from windows (including sunroofs) NOTE: For roofs that are not metallic, use the included metal disk by peeling away the adhesive cover and sticking on the clean surface. WORKS WITH ALL VEHICLES CELL PHONE SIGNAL BOOSTER DRIVE SLEEK ______ Step 2: Route & Connect Booster Route the cable into the vehicle. See examples below. NOTE: The cable is strong enough that it may be shut in most vehicle doors without damaging the cable. Car/Sedan: Cable routed into rear side door. SUV/Van/Hatchback: Cable routed into top of hatchback door. Truck: Cable routed into side door. DRIVE SLEEK CELL PHONE SIGNAL BOOSTER ______ (STEP 2 cont.) Connect the cable from the outside antenna to the booster port labeled ANTENNA by simply pressing the connector in until you hear a “click”. booster cable from outside antenna ANTENNA CELL PHONE SIGNAL BOOSTER DRIVE SLEEK ______ Step 3: Route Cable To Front Of Vehicle We recommend routing the 15ft. fixed cable from the booster, under mats and between seats up to the front of the vehicle where the cradle will be located. to front of vehicle Connect booster cable to cable from cradle. cradle DRIVE SLEEK CELL PHONE SIGNAL BOOSTER snap-in connectors ______ Step 4: Connect System To Power Connect the power to the 12V CLA port on your vehicle and route power cable back to the booster. NOTE: We recommend routing with the same path as the cable going up to the cradle (under mats and between seats). connect power supply to 12V port connect to booster Connect power cable to booster port labeled NOTE: The booster will be on whenever there is power from the 12V CLA ANTENNA port. If your vehicle always has power going to this port, you may want to unplug this when you’re not driving so the booster does not drain your battery. CELL PHONE SIGNAL BOOSTER DRIVE SLEEK ______ Step 5: Insert Your Phone Into Cradle Make sure you have plenty of slack in the cable going up to the cradle (velcro straps included to manage excess cable). Insert your phone into cradle and watch your signal increase! insert phone into cradle to boost signal cradle extends magnetic vent mount NOTE: Magnetic vent mount included to mount the cradle to your dash. DRIVE SLEEK CELL PHONE SIGNAL BOOSTER ______ Light Patterns Solid White This indicates that your booster is functioning properly and at maximum gain. Light Off Needs power. NEED HELP? support.weboost.com 866.294.1660 CELL PHONE SIGNAL BOOSTER DRIVE SLEEK ______ Troubleshooting FIXING BLINKING LIGHT ISSUES Make sure all connections are tight. Increase the distance between the outside antenna and cradle, by moving them horizontally and/or vertically farther apart until the light change to green. Remember to keep the antenna at least 6 inches from any window or sunroof. Reset system by disconnecting and reconnecting the power supply. If you are having any difficulties while testing or installing your booster, contact our weBoost Customer Support team for assistance (866.294.1660). FREQUENTLY ASKED QUESTIONS What hours can I contact customer support? Customer Support can be reached monday thru friday by calling 866.294.1660, or through our support site at support.weboost.com. Why do I need to create distance between the booster and the antenna? Antennas connected to a booster create spheres of signal. When these spheres overlap, a condition called oscillation occurs. Oscillation can be thought of as noise, which causes the booster to shut down to prevent damage. The best way to keep these spheres of signal from overlapping is to maximize separation between the Booster and Antenna. NEED HELP? support.weboost.com DRIVE SLEEK CELL PHONE SIGNAL BOOSTER 866.294.1660 ______ Antenna Kit Options MOBILE Outside Antenna Options Mini-Mag 301126 w/ 12.5 RG174 cable - SMA 301113 w/ 12.5 RG174 cable - FME 12” Mag Mount w/12.5’ RG58 301103 311125 311128 314202 311703 Trucker Antenna w/10.5’ RG58 311101 311701 10 4G Trucker Antenna w/13.5’ RG58 311119 311133 4G Trucker Antenna w/15’ RG58 304415 304414 Marine Antenna w/10’ RG58 311130-5810 Marine Antenna w/20’ RG58 304420 Glass Mount w/14’ RG58 311102 NMO Antenna w/RG174 Kit 311104-17410 800/1900 NMO Antenna 10’ RG174 Cable Kit 311112-17410 800/1900 NMO Antenna 10’ RG174 Cable Kit 314203-17410 800/900/1900 NMO Antenna 10’ RG174 Cable NMO Antenna w/RG58 Kit 311104-5810 800/1900 NMO Antenna 10’ RG58 Cable Kit 311112-5810 800/1900 NMO Antenna 10’ RG58 Cable Kit 314203-5810 800/900/1900 NMO Antenna 10’ RG58 Cable CELL PHONE SIGNAL BOOSTER DRIVE SLEEK ______ Safety Guidelines Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than 150 degrees Fahrenheit). It is not intended for use in attics or similar locations subject to temperatures in excess of that range. The outside antenna must be installed no higher than 10 meters (32’9”) above ground. Any antenna used with this device must be located at least 8 inches from all persons. FCC requires to never use the cell phone in the cradle next to your ear. This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from (i.e., MUST NOT be installed within 20 cm of) any person. You MUST cease operating this device immediately if requested by the FCC (or ISED in Canada) or licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. ISED CPC-2-1-05: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS PROVIDER, PLEASE SEE BELOW: Sprint: http://www.sprint.com/legal/fcc_boosters.html T-Mobile/MetroPCS: https://support.t-mobile.com/docs/DOC-9827 Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html AT&T: https://securec45.securewebsession.com/attsignalbooster.com/ U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp DRIVE SLEEK CELL PHONE SIGNAL BOOSTER 11 ______ Specifications Drive Sleek Model Number 460035 FCC ID: PWO460035 IC: 4726A-460035 Frequency 698-716 MHz, 729-746 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Maximum Power Power output for single cell phone (Uplink) dBm 700 MHz Band 12/17 18.74 700 MHz Band 13 21.57 800 MHz Band 5 22.65 1700 MHz Band 4 25.56 1900 MHz Band 2 19.19 Power output for single cell phone (Downlink) dBm 700 MHz Band 12/17 2.1 700 MHz Band 13 2.1 800 MHz Band 5 -2.5 2100 MHz Band 4 -0.6 1900 MHz Band 2 2.5 Noise Figure Power Requirements 12 5 dB nominal 12 V 1.5 A / USB 5V 2.1 A CELL PHONE SIGNAL BOOSTER DRIVE SLEEK ______ (SPECIFICATIONS cont.) The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor. This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment. DRIVE SLEEK CELL PHONE SIGNAL BOOSTER 13 2 YEAR WARRANTY weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product. This warranty does not apply to any Signal Boosters determined by weBoost to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties. Replacement products may include refurbished weBoost products that have been recertified to conform with product specifications. RMA numbers may be obtained by contacting Customer Support DISCLAIMER: The information provided by weBoost is believed to be complete and accurate. However, no responsibility is assumed by weBoost for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use. 3301 East Deseret Drive, St. George, UT 866.294.1660 www.weboost.com support.weboost.com Copyright © 2016 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA GDE000009_RevP_ErinFCC_07.10.17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2017:07:10 14:58:24-06:00 Creator : Adobe InDesign CC 2017 (Windows) Modify Date : 2017:07:26 15:12:08-06:00 Has XFA : No Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2017:07:26 15:12:08-06:00 Creator Tool : Adobe InDesign CC 2017 (Windows) Instance ID : uuid:adcc41dc-891d-4826-8207-e4459fc7303e Original Document ID : xmp.did:1f27a136-e1bb-48c3-bdc5-a32b0d8df0cb Document ID : xmp.id:dd95d4b2-bb45-0d4a-bc87-30a7c93f8e6a Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:0d99cdf1-11cf-0843-9f6e-d332606670b7 Derived From Document ID : xmp.did:0d99cdf1-11cf-0843-9f6e-d332606670b7 Derived From Original Document ID: xmp.did:1f27a136-e1bb-48c3-bdc5-a32b0d8df0cb Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2017 (Windows) History Changed : / History When : 2017:07:10 14:58:24-06:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 16EXIF Metadata provided by EXIF.tools