Wilson Electronics 8013SB In Building Wireless PCS Smart Amplifier User Manual users manual

Download:
Mirror Download [FCC.gov]
Document ID	646947
Application ID	SOOahX6gh62PwwLEwwnXbQ==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	102.97kB (1287151 bits)
Date Submitted	2006-04-13 00:00:00
Date Available	2006-04-11 00:00:00
Creation Date	2006-04-10 11:51:48
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2006-04-10 12:05:20
Document Title	users manual
Document Creator	Adobe InDesign CS2 (4.0.2)

Wireless
IN-BUILDING
PCS Smart Technology™ Amplifier
Installation Guide
In-Building
Wireless PCS
Smart TechnologyTM Amplifier
PART # 801306
1850-1990 MHz
FCC ID: PWO8013SB
IC: 4726A-8013SB
Wilson Electronics, Inc.
3301 E. Deseret Drive, St. George, Utah 84790
For additional technical support visit
www.wilsonelectronics.com
Phone: 1-866-294-1660
Fax: 1-435-656-2432
The term “IC:” before the radio certification number signifies
that Industry of Canada technical specifications were met.
1. PURPOSE OF THE AMPLIFIER
The PCS Smart TechnologyTM Amplifier improves RF coverage for areas in which low signal
strength is a concern.
2. PACKAGE CONTENTS
2.1 Amplifier
2.2 AC/DC 110 volt Power Supply
3. HOW THE AMPLIFIER FUNCTIONS
The signal is received by the outside antenna from the cell site. The signal is then
AMPLIFIED and transmitted to your phone through the inside antenna. When the phone
transmits, the signal is received by the inside antenna and then AMPLIFIED and transmitted
to the cell site through the outside antenna.
4. AMPLIFIER INSTALLATION (see illustration on pg. 4 & 5)
4.1 Installing the Wilson Cellular Outside Antenna
WARNING: The outside antenna used with this amplifier must be fixed-mounted on
an outdoor permanent structure with a separation of at least 20 feet from all persons
during normal operation.
4.1.1 Select a location on the roof using your phone in test mode to find the best signal
strength. (See leaflet titled PHONE TEST MODES)
4.1.2 The outside antenna should be located in an area with at least a 3 foot radius clear of
obstructions and other radiating elements.
4.2 Installing The Amplifier
WARNING: Connecting amplifier directly to cell phone may damage phone.
WARNING: Connect both antennas before connecting power to the amplifier.
4.2.1 Mount the AMPLIFIER on a wall or ceiling using #6 screws.
NOTE: Mount the AMPLIFIER away from direct sunlight, excessive heat and/or
moisture. The amplifier needs proper ventilation. DO NOT place the amplifier
in an air-tight enclosure.
4.2.2 Connect outside antenna to the amplifier side labeled “OUTSIDE ANTENNA”.
4.2.3 Connect inside antenna to the amplifier side labeled “INSIDE ANTENNA”.
4.2.4 Verify that both the outside and inside antennas are connected before connecting
the AC-DC power supply to the power outlet.
4.3 Indicator Lights
ALL LIGHTS GREEN = 60 dB GAIN
LIGHT D OFF = 2 dB REDUCTION
LIGHT D & C OFF = 10 dB REDUCTION
LIGHT D, C & B OFF = 20 dB REDUCTION
LIGHT A RED = 40 dB REDUCTION
4.4 Installing The Wilson Cellular Inside Antenna
4.4.1 See antenna packaging for model specific instructions.
4.4.2 The inside antenna should be centered in the weak signal area. The inside antenna
should be at least 7 feet from the floor.
FCC Separation Warning
WARNING: The inside antenna used with this amplifier must have a separation
distance from all persons that is at least:
9 inches for the 2.5 dBi Dome antenna.
14 inches for the 7 dBi Panel antenna.
The amplifier must not be co-located or operating in conjunction with any other
antenna or amplifier.
4.5 When covering multiple areas a 1900 MHz splitter can be used to allow for more than one
inside antenna. Extension cables can also be used if the weak signal area is located far from the
location of the outside antenna. For coax runs more than 20 feet use 9913 or equivalent coax.
NOTE: For Maximum gain (60 dB), keep a separation distance of at least 50 feet
between the outside and inside antennas. Closer spacings may be used,
but may cause the amplifier to automatically reduce its gain.
NOTE: When using a Yagi antenna make sure the Yagi is pointed away from the
inside antenna.
Outside Antenna
1900 MHz Yagi Antenna Shown
Cell
Site
Amplifier
Outside Antenna to
Amplifier Connection
Inside Antenna to
Amplifier Connection
AC / DC
Power Supply
Supports
Multiple
Users
If using a Yagi Antenna,
Make sure the Yagi is not pointed
toward the inside antenna.
AMPLIFIER PHYSICAL
SPECIFICATIONS
Connectors
Dimensions
Weight
N-Female 50 ohms
4.5 x 3.5 x 1.25 inches
11.4 x 8.9 x 3.2 (cm)
1.5 lbs / 0.7 kg
AMPLIFIER LAYOUT
DIAGRAM
For maximum gain, keep a separation
distance of at least 50 feet between the
outside and inside antennas.
5. AMPLIFIER SPECIFICATIONS
Inside Antenna
Optional Dome
Antenna Shown
Part Number
801306
Gain
60 dB
PCS
1850-1910 MHz / 1930-1990 MHz
Frequency
Linear Output Power
30 dBm
Max Output Power
3 watts
Max RF (up/down)
+30 dBm / +30 dBm
Noise Figure (typical)
4 dB
Flatness (up/down)
± 4 dB
Isolation
> 90 dB
Power Requirements
120 V AC 3 A Max
Connectors
N-Female
4.5 x 3.5 x 1.25 (inch)
Dimensions
11.43 x 8.9 x 3.2 (cm)
Weight
1.5 lbs / 0.7 kg
6. OPTIONAL ACCESSORIES/ANTENNA OPTIONS
WARNING: Lightning protection is recommended for all installations.
6.1 3dB Dual-Band Splitter Part # 859911
6.2 Coax Cable Extensions 50Ω (see chart on next page)
6.3 Antenna Options:
Inside Antenna Options		
Outside Antenna Option
301103 - Magnet Mount 5 dBi		
301124 - Yagi 13 dBi
301106 - Low Profile 2.2 dBi
301113 - Mini Magnet 2.12 dBi
301121 - Dome 2.5 dBi
301122 - Panel 7 dBi
301123 - Dual Polarity Dome, Unity
6.4 N-Male to FME-Male adapter Part # 971113
6.5 Lightning Surge Protection Part # 859902
7. TECH SUPPORT
If you need further assistance with your installation:
1) Call Toll-Free 866-294-1660 8:00 AM – 4:30 PM (Mountain Time)
2) E-mail tech support at tech@wilsonelectronics.com
3) Visit www.wilsonelectronics.com
8. WARNINGS
WARNING: The outside antenna used with this amplifier must be fixed-mounted on an outdoor permanent structure with a separation of at least 20 feet from all persons
during normal operation.
WARNING: The inside antenna used with this amplifier must have a separation distance
from all persons that is at least:
9 inches for the 2.5 dBi Dome antenna.
14 inches for the 7 dBi Panel antenna.
The amplifier must not be co-located or operating in conjunction with any
other antenna or amplifier.
WARNING: Verify that both the Outside and Inside Antennas are connected before plugging in the AC/DC power supply to the power outlet.
WARNING: Lightning protection is recommended for all installations.
Lightning protection is required for warranty validation.
The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no responsibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from its use, or for any
infringements of patents or other rights of third parties that may result from its use.
Copyright © 2006 Wilson Electronics, Inc.
EXTENSION CABLE CHART
951110
2’ Extension Cable RG58U
Low Loss Coax
N-Male to FME-Female
Used with the Yagi antenna to help find the
optimum signal strength (for installation purposes
only).
951101
5’ Extension Cable RG58U
Low Loss Coax
0.6 dB loss
951102
10’ Extension Cable RG58U
Low Loss Coax
1.2 dB loss
951103
15’ Extension Cable RG58U
Low Loss Coax
1.8 dB loss
951104
20’ Extension Cable RG58U
Low Loss Coax
2.4 dB loss, N-Male to FME-Female
951113
2’ Extension Cable 9913 Equivalent
Ultra Low Loss Coax
0.08 dB loss, Jumper Coax - Can be used to connect a splitter behind an amplifier.
951108
20’ Extension Cable 9913 Equivalent
Ultra Low Loss Coax
Only use 9913 Equivalent Low Loss Coax for
extensions 20 feet or longer, 0.8 dB loss
951105
30’ Extension Cable 9913 Equivalent
Ultra Low Loss Coax
1.2 dB loss
951106
50’ Extension Cable 9913 Equivalent
Ultra Low Loss Coax
2.0 dB loss
951117
75’ Extension Cable 9913 Equivalent
Ultra Low Loss Coax
3.0 dB loss
951107
100’ Extension Cable 9913 Equivalent
Low Loss Coax
4.0 dB loss
RG58U - FME connectors / 9913 Equivalent - N connectors
The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is
re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power
or gain reduction and not by an attenuator at the output of the device.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of this device.
1900 MHz
Yagi
Optional Accessories
Dome
FME Male to
N-Male
Lightning Suppressor
Coax Cable Extension
Ultra Low Loss Coax
15 DAY
MONEY BACK
GUARANTEE
All Wilson products
have a 15 day
money back
guarantee with
Proof of Purchase
Dual Polarity
Dome
Panel
Mini
Magnet
Low
Profile
Magnet
Mount
Trucker 3/8"
Mount
1 YEAR WARRANTY
The Wilson amplifier is warranted for one year against defects in workmanship
and/or materials and will be repaired or replaced, at the discretion of the manufacturer, to the original purchaser with dated proof of purchase or sales receipt.
If any questions arise about an amplifier please call technical support tollfree 1-866-294-1660 or E-mail tech@wilsonelectronics.com
Most warranty cases may be handled by taking the amplifier and the receipt to the store where it was purchased. If inconvenient, the amplifier and a
copy of the receipt, may be sent to the factory, at purchasers expense. It will
be repaired or replaced and returned shipping paid. Warranty does not cover
damages caused by abuse, misuse, and negligence.
801306_006 / 04.06.06

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 8
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:c99e5862-4f62-4265-83b1-7def64b59bfc
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2006:04:10 11:51:48-06:00
Modify Date                     : 2006:04:10 12:05:20-06:00
Metadata Date                   : 2006:04:10 12:05:20-06:00
Creator Tool                    : Adobe InDesign CS2 (4.0.2)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 13843 bytes, use -b option to extract)
Version ID                      : 1
Instance ID                     : uuid:64c9fd95-8283-4559-8d3b-b425a7597e36
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:cbeaea4d-c8a0-11da-bbd2-c98c528ed1b0
Derived From Instance ID        : 557e610c-c5bd-11da-9fc8-a6c5166d76c0
Derived From Document ID        : adobe:docid:indd:b1999699-c596-11da-9fc8-a6c5166d76c0
Derived From Version ID         : 1
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:aaf2d1d2-4859-43b3-b067-01879a8f3007, uuid:814c1e22-dc20-45f9-aaa2-1b2e3b36dc07, uuid:CA23F4A27488DA118200A07DB41E56A2, uuid:CA23F4A27488DA118200A07DB41E56A2, uuid:1d7d75fd-4481-477f-955e-3e392a0ee330, uuid:1d7d75fd-4481-477f-955e-3e392a0ee330, uuid:75a72d9e-2096-4584-8938-b42f82cd83a3
Manifest Reference Document ID  : uuid:FDC5B9720689DA11B4D5E8587D2C61A1, uuid:98D6C96387AFDA11856C88F79B1C67B9, uuid:C923F4A27488DA118200A07DB41E56A2, uuid:C923F4A27488DA118200A07DB41E56A2, uuid:FFC5B9720689DA11B4D5E8587D2C61A1, uuid:FFC5B9720689DA11B4D5E8587D2C61A1, uuid:01C6B9720689DA11B4D5E8587D2C61A1
Format                          : application/pdf
Creator                         : Adobe InDesign CS2 (4.0.2)

EXIF Metadata provided by EXIF.tools