Wilson Electronics 8040SB In-Building Wireless iDEN SmartTech Amplifier User Manual

Download:
Mirror Download [FCC.gov]
Document ID	564402
Application ID	2psaji43g4rOMrcaEUiTxQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	43.68kB (545966 bits)
Date Submitted	2005-07-21 00:00:00
Date Available	2005-07-21 00:00:00
Creation Date	2005-07-12 16:56:55
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2005-07-12 17:31:12
Document Title	Users Manual
Document Creator	Adobe InDesign CS2 (4.0)

Cellular & iDEN
Analog & Digital - CDMA, GPRS, GSM, TDMA
Wireless
IN-BUILDING
Cellular & iDEN Amplifier
Installation Guide
In-Building
Wireless Cellular
Smart TechnologyTM
Amplifier
824-894 MHz
FCC ID:PWO8011SB
IC: 4726A-8011SB
In-Building
Wireless iDEN
Smart TechnologyTM
Amplifier
806-866 MHz
FCC ID:PWO8040SB
IC: 4726A-8040SB
Wilson Electronics, Inc.
3301 E. Deseret Drive, St. George, Utah 84790
For additional technical support go to
www.wilsonelectronics.com
Phone: 1-866-294-1660
Fax: 1-435-656-2432
The term “IC:” before the radio certification number only signifies
that Industry of Canada technical specifications were met.
1. PURPOSE OF THE AMPLIFIER
4.2 Indicator Lights
The Smart TechnologyTM Amplifiers improve RF coverage for areas in which low signal
strength is a problem.
2. PACKAGE CONTENTS
2.1 Amplifier
2.2 AC-to-DC (110 volt) Power Supply
3. HOW THE AMPLIFIER FUNCTIONS
The signal is received by the outside antenna from the cell site. The signal is then
AMPLIFIED and transmitted to your phone through the inside antenna. When the phone
transmits, the signal is received by the inside antenna and then
AMPLIFIED and transmitted to the cell site through the outside antenna.
ALL LIGHTS GREEN = 60 dB GAIN
LIGHT D OFF = 2 dB REDUCTION
LIGHT D & C OFF = 10 dB REDUCTION
4. AMPLIFIER INSTALLATION (see illustration on pg. 4 & 5)
4.1 Installing the Wilson Cellular Outside Antenna
4.1.1 Select a location on the roof using your phone in test mode to find the best signal
strength. (See leaflet titled PHONE TEST MODES)
4.1.2 The Outside Antenna should be located in an area with at least a 3’ radius clear of
obstructions and other radiating elements.
NOTE: Mount the AMPLIFIER away from direct sunlight, excessive heat
and/or moisture. The amplifier needs proper ventilation.
DO NOT place the amplifier in an air-tight enclosure.
WARNING: The outside antenna used with this amplifier must be fixed-mounted on
an outdoor permanent structure with a separation of at least 20 feet from all persons
during normal operation.
4.2 Installing The Amplifier
WARNING: Connecting amplifier directly to cell phone may damage phone.
WARNING: Connect both antennas before connecting power to the amplifier.
4.2.1 Mount the AMPLIFIER on a wall or ceiling using #6 screws.
4.2.2 Connect Outside Antenna to the AMPLIFIER side labeled “OUTSIDE ANTENNA”.
4.2.3 Connect Inside Antenna to the AMPLIFIER side labeled “INSIDE ANTENNA”.
4.2.4 Verify that both the OUTSIDE and INSIDE antennas are connected
before connecting the AC-DC power supply to the power outlet.
LIGHT D, C & B OFF = 20 dB REDUCTION
LIGHT A RED = 40 dB REDUCTION
4.4 Installing The Wilson Cellular Inside Antenna
4.4.1 See antenna packaging for model specific instructions.
4.4.2 The Inside Antenna should be centered in the weak signal area. The INSIDE ANTENNA should be at least 7’ from the floor.
WARNING: The inside antenna used with this amplifier must have a separation distance from all persons that is at least:
9 inches for the 2.5 dBi Dome antenna.
14 inches for the 7 dBi Panel antenna.
The amplifier must not be co-located or operating in conjunction with any other
antenna or amplifier.
4.5 When covering large areas a splitter can be used to allow for more than one inside antenna.
Extension cables can also be used if the weak signal area is located far from the location of the
outside antenna. For coax runs more than 20’ use 9913 or equivalent coax.
NOTE: For Maximum gain (60 dB), keep a separation distance of at least 75 feet
between the outside and inside antennas. Closer spacings may be used,
but may cause the amplifier to (automatically) reduce its gain.
NOTE: When using the Yagi antenna make sure the Yagi is pointed away from
the inside antenna.
Outside Antenna
AMPLIFIER LAYOUT
DIAGRAM
Yagi Antenna Shown
For maximum gain, keep a separation
distance of at least 75 ft between the
outside and inside antennas.
Cell
Site
Amplifier
Outside Antenna to
Amplifier Connection
If using the Yagi Antenna,
Make sure the Yagi is not pointed
toward the inside antenna.
Inside Antenna to
Amplifier Connection
AC/DC
Power Supply
Supports
Multiple
Users
Inside Antenna
AMPLIFIER PHYSICAL
SPECIFICATIONS
Optional Dome
Antenna Shown
Connectors
Dimensions
N-Female 50 Ohms
4.5” x 3.5” x 1.25”
(11.4 x 8.9 x 3.2 cm)
1.5 lbs (682 gr)
Weight
5. AMPLIFIER SPECIFICATIONS FOR CELLULAR MODEL
Part #
Frequency
801106
824-849 MHz Uplink 869-894 MHz Downlink
AMPLIFIER SPECIFICATIONS FOR iDEN MODEL
Part #
Frequency
804006
806-821MHz Uplink 851-866MHz Downlink
Gain (up/down)
60 dB Max
Gain (up/down)
60 dB Max
Flatness (up/down)
+/- 2.5 dB
Flatness (up/down)
+/- 2.5 dB
Max RF (up/down)
+ 32 dBm
Max RF (up/down)
+ 32 dBm
Noise Figure (down)
3 dB nominal
Noise Figure (down)
3 dB nominal
Isolation
Uplink/Downlink More than 90 dB
Power Consumption
13.8 V, 1.5 A
Isolation
Uplink/Downlink More than 90 dB
Power Consumption
13.8 V, 1.5 A
Receiver overload light
Outside antenna has exceeded -5 dBM
Receiver overload light
Outside antenna has exceeded -5 dBM
Transmit overload light
Inside antenna has exceeded -5 dBM
Transmit overload light
Inside antenna has exceeded -5 dBM
6. OPTIONAL ACCESSORIES/ANTENNA OPTIONS
6.1 3 dB Splitter (Part# 859901)
6.2 6 dB Tap (Part# 859906) & 10 dB Tap (Part# 859907)
6.3 Coax Cable Extensions 50Ω (see chart on next page)
6.4 Antenna Options:
Inside Antenna Options		
Outside Antenna Option
301103 - Magnet Mount, 5 dBi		
301111 - Yagi, 13 dBi
301106 - Low Profile, 2.2 dBi
301113 - Mini Magnet, 2.12 dBi
301121 - Dome, 2.5 dBi
301122 - Panel, 7 dBi
6.5 N-Male to FME-Male adapter (Part# 971113)
Adapts 9913 Coax to fit the Amplifier
6.6 Lightning Surge Protection (Part# 859903)
WARNING: Lightning protection is recommended for all installations.
7. TECH SUPPORT
If you need further assistance with your installation:
1) Call us Toll-Free at 866-294-1660 (8:00 AM – 4:30 PM Mountain Time)
2) E-mail tech support at tech@wilsonelectronics.com
3) Go to www.wilsonelectronics.com
8. WARNINGS
WARNING: The outside antenna used with this amplifier must be fixed-mounted on an outdoor permanent structure with a separation of at least 20 feet from all persons
during normal operation.
WARNING: The inside antenna used with this amplifier must have a separation distance
from all persons that is at least:
9 inches for the 2.5 dBi Dome antenna.
14 inches for the 7 dBi Panel antenna.
The amplifier must not be co-located or operating in conjunction with any
other antenna or amplifier.
WARNING: Verify that both the Outside and Inside Antennas are connected before plugging in the AC-DC power supply to the power outlet.
WARNING: Lightning protection is recommended for all installations.
Lightning protection is required for warranty validation.
The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no responsibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from its use, or for any
infringements of patents or other rights of third parties that may result from its use.
Copyright © 2004 Wilson Electronics, Inc.
EXTENSION CABLE CHART
951110
2’ Extension Cable RG58U
Low Loss Coax
(N-Male to FME Female)
Used with the Yagi antenna to help find the
optimum signal strength (for installation purposes
only).
951101
5’ Extension Cable RG58U
Low Loss Coax
(0.6 db loss)
951102
10’ Extension Cable RG58U
Low Loss Coax
(1.2 db loss)
951103
15’ Extension Cable RG58U
Low Loss Coax
(1.8 db loss)
951104
20’ Extension Cable RG58U
Low Loss Coax
(2.4 db loss) N-Male to FME Female
951113
2’ Extension Cable 9913 Equivalent
Ultra Low Loss Coax
(0.08 db loss) Jumper Coax - Can be used to connect a splitter behind an amplifier.
951108
20’ Extension Cable 9913 Equivalent
Ultra Low Loss Coax
Only use 9913 Equivalent Low Loss Coax for
extensions 20’ or longer (0.8 db loss)
951105
30’ Extension Cable 9913 Equivalent
Ultra Low Loss Coax
(1.2 db loss)
951106
50’ Extension Cable 9913 Equivalent
Ultra Low Loss Coax
(2.0 db loss)
951117
75’ Extension Cable 9913 Equivalent
Ultra Low Loss Coax
(3.0 dB Loss)
951107
100’ Extension Cable 9913 Equivalent
Low Loss Coax
(4.0 db loss)
RG58U - FME connectors / 9913 Equivalent - N connectors
The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is
re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power
or gain reduction and not by an attenuator at the output of the device.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of this device.
Yagi
Single-Band
Optional Accessories
Dome
FME Male to
N-Male
3 dB Splitter
Lightning Suppressor
Panel
6 dB Tap
10 dB Tap
15 DAY
MONEY BACK
GUARANTEE
All Wilson products
have a 15 day
money back
guarantee with
Proof of Purchase
Coax Cable Extension
Ultra Low Loss Coax
Mini
Magnet
Low
Profile
Magnet
Mount
Trucker 3/8"
Mount
1 YEAR WARRANTY
The Wilson amplifier is warranted for one year against defects in workmanship
and/or materials and will be repaired or replaced, at the discretion of the manufacturer, to the original purchaser with dated proof of purchase or sales receipt.
If you have questions about your amplifier please call technical support
call 1-866-294-1660 or E-mail tech@wilsonelectronics.com
Most warranty cases can be handled by taking the amplifier and the receipt to the store where it was purchased. If inconvenient, the amplifier and a
copy of the receipt, may be sent to the factory, at purchasers expense, where
it may be repaired or replaced and returned shipping paid. Warranty does not
cover damages caused by abuse, misuse, and negligence.
801106_804006_005

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 5
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:c502ffa5-af01-4867-8fbf-03fdea2c964e
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2005:07:12 16:56:55-06:00
Modify Date                     : 2005:07:12 17:31:12-06:00
Metadata Date                   : 2005:07:12 17:31:12-06:00
Creator Tool                    : Adobe InDesign CS2 (4.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 14252 bytes, use -b option to extract)
Version ID                      : 1
Instance ID                     : uuid:2d6c65cd-7e9b-47b0-b56d-ed8097540c65
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:c6e84ba8-f324-11d9-a488-df81eb5d3fc8
Derived From Instance ID        : 95fd3898-f313-11d9-a488-df81eb5d3fc8
Derived From Document ID        : adobe:docid:indd:95fd3893-f313-11d9-a488-df81eb5d3fc8
Derived From Version ID         : 1
Format                          : application/pdf
Creator                         : Adobe InDesign CS2 (4.0)

EXIF Metadata provided by EXIF.tools