Wilson Electronics 824WB56 In-Building Bidirectional Amplifier User Manual

Wilson Electronics, LLC In-Building Bidirectional Amplifier Users Manual

Users Manual

AMPSIN BUILDINGBi-directional Amplier#801102 (43dB Model)#801103 (50dB Model)#801104 (60dB Model)FCC ID: PWO824WB56IC: 4726A-824WB56iDENIN BUILDINGBi-directional Amplier#804001 (43dB Model)#804003 (50dB Model)#804004 (60dB Model)FCC ID: PWO806WB56IC: 4726A-806WB56Installation GuideWilson Electronics, Inc.3301 E. Deseret Drive, St. George, Utah 84790For additional technical support go towww.wilsonelectronics.comPhone: 1-866-294-1660 Fax: 1-435-656-2432IN BUILDINGWirelessThe term “IC:” before the radio certification number only signifiesthat Industry of Canada technical specifications were met.
231. PURPOSE OF THE AMPS/iDEN AMPLIFIERThe AMPS/iDEN Bi-directional Amplier improves RF coverage for areas in which low signal strength or no signal is a problem. 2. PACKAGE CONTENTS 2.1 AMPS/iDEN Bi-directional Amplier 2.2 AC-to-DC (110 volt) Power Supply3. HOW THE AMPS/iDEN AMPLIFIER FUNCTIONSThe signal is received by the outside antenna from the cell site. The signal is then AMPLIFIED and transmitted to your phone through the inside antenna. When the phone transmits, the signal is received by the inside antenna and thenAMPLIFIED and transmitted to the cell site through the outside antenna.The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no responsibility is assumed by Wilson Electronics, Inc. for any business or per-sonal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.Copyright © 2004 Wilson Electronics, Inc.
234. AMPLIFIER INSTALLATION (see illustration on 4-5)4.1 Installing the Wilson Cellular Outside Antenna4.1.1 Select a location on the roof using your AMPS/iDEN phone in test mode to nd the best signal strength. (See leaet titled PHONE TEST MODES) 4.1.2 The Outside Antenna should be located in an area with at least a 3’ radius clear of obstructions and other radiating elements. NOTE: Mount the AMPLIFIER away from direct sunlight, excessive heatand/or moisture. The amplifier needs proper ventilation. DO NOT place the amplifier in an air-tight enclosure.WARNING: The outside antenna used with this amplier must be xed-mounted on an outdoor permanent structure with a separation of at least 20 feet from all persons during normal operation.4.2 Installing The AmplierWARNING: Connecting amplier directly to cell phone may damage phone.4.2.1 Mount the AMPLIFIER on a wall or ceiling using #6 screws.4.2.2 Connect the Outside Antenna to the AMPLIFIER side labeled “OUTSIDE ANTENNA”.4.2.3 Connect the Inside Antenna to the AMPLIFIER side labeled “INSIDE ANTENNA”.4.2.4 Verify that both the OUTSIDE and INSIDE antennas are connected be-fore connecting the AC-DC power supply to the power outlet.4.3 Installing The Wilson Cellular Inside Antenna4.3.1 The Inside Antenna should be centered in the weak signal area. The INSIDE ANTENNA should be at least 7’ from the ground.WARNING: The inside antenna used with this amplier must be mounted with a separation distance of at least 8 inches from all persons and must not be co-located or operating in conjunction with any other antenna or amplier.4.4 When covering large areas a splitter can be used to allow for more than one inside antenna. Extension cables can also be used if the weak signal area is located far from the location of the outside antenna. NOTE: A minimum of 20’ coax extension is recommended for isolation between antennas.
45             5. AMPLIFIER SPECIFICATIONS FOR AMPS 43dB, 50dB & 60dB MODELS Part #: 801102 (43dB Model) & 801103 (50dB Model) & 801104 (60dB Model)43dB 50dB 60dBFrequency 824-849MHz Uplink 869-894MHz DownlinkGain (up/down) (43dB/43dB) (50dB/50dB) (60dB/60dB) Flatness (up/down) (+/- 4dB/+/-4dB) (+/- 4dB/+/-6dB) (+/- 4dB/+/-6dB) Max RF (up/down) (+31dBm/+15dBm) (+35dBm/+15dBm) (+35dBm/+15dBm) Noise Figure (down) (3dB nominal) (3dB nominal) (3dB nominal) Isolation Uplink/Downlink More than 90dBPower Consumption 13.8V, 1.5A
45AMPLIFIER LAYOUTKEEP A SEPARATION DISTANCE OF AT LEAST 20ft HORIZONTAL AND 5ft VERTI-CAL BETWEEN ANTENNASIf using the Yagi Antenna, make sure the Yagi is pointed AWAY from the inside antenna.             AMPLIFIER SPECIFICATIONS FOR iDEN 43dB, 50dB & 60dB MODELS Part #: 804001 (43dB Model) & 804003 (50dB Model) & 804004 (60dB Model)43dB 50dB 60dBFrequency 806-821MHz Uplink 851-866MHz DownlinkGain (up/down) (43dB/43dB) (50dB/50dB) (60dB/60dB) Flatness (up/down) (+/- 4dB/+/-4dB) (+/- 4dB/+/-6dB) (+/- 4dB/+/-6dB) Max RF (up/down) (+35dBm/+15dBm) (+35dBm/+15dBm) (+35dBm/+15dBm) Noise Figure (down) (3dB nominal) (3dB nominal) (3dB nominal) Isolation Uplink/Downlink More than 90dBPower Consumption 13.8V, 1.5AAMPS/iDEN AMPLIFIER PHYSICALSPECIFICATIONSConnectors FME-Male 50 OhmsDimensions 5.5x4.3x1.4 (inch) or 14.0x10.8x3.5 (cm)Weight 1.32 Pounds or 600G
676. OPTIONAL ACCESSORIES/ANTENNA OPTIONS6.1 2-Way RF Splitter - allows for multiple inside antennas.6.2 Coax Cable Extensions 50Ω (see chart on next page)6.3 Antenna Options:Inside Antenna Options Outside Antenna Option301103 - Magnet Mount 301111 - Yagi301106 - Stealth301113 - Mini Magnet6.4 N-Female To FME-Female Adapter - Adapts 9913 Coax to t the AMPS/iDEN Bi-directional Amplier6.5 Lightning SuppressorWARNING: Lightning protection is recommended for all installations.6.6 DC Power Cable7. TECH SUPPORTIf you need further assistance with your installation:1) Call us Toll-Free at 866-294-16602) E-mail tech support at tech@wilsonelectronics.com3) Go to www.wilsonelectronics.comOur Hours of Operation are: 8:00 AM – 4:30 PM (Mountain Time)8. WARNINGSWARNING: The outside antenna used with this amplier must be xed-mounted on an outdoor permanent structure with a separation of at least 20 feet from all persons during normal operation.WARNING: The inside antenna used with this amplier must be mounted with a separation distance of at least 8 inches from all persons and must not be co-located or operating in conjunction with any other antenna or amplier.WARNING: Verify that both the Outside and Inside Antennas are connected before plugging in the AC-DC power supply to the power outlet.WARNING: Lightning protection is recommended for all installations.
67951101 5’ Extension Cable RG 58Low Loss Coax(0.6 db loss)951102 10’ Extension Cable RG 58Low Loss Coax(1.2 db loss)951103 15’ Extension Cable RG 58Low Loss Coax(1.8 db loss)951104 20’ Extension Cable RG 58Low Loss Coax(2.4 db loss) Used with the YagiAntenna - (N-Male to FME Female)951108 20’ Extension Cable 9913Ultra Low Loss CoaxOnly use 9913 Low Loss Coax for extensions 20’ or longer (0.8 db loss)951105 30’ Extension Cable 9913Ultra Low Loss Coax(1.2 db loss)951106 50’ Extension Cable 9913Ultra Low Loss Coax(2.0 db loss)951107 100’ Extension 9913 LowLoss Coax(4.0 db loss)951110 2’ Extension RG 58 LowLoss Coax(N-Male to FME Female)Used with the Yagi antenna to help nd the optimum signal strength (for installation purposes only).951113 2’ Extension 9913 Ultra Low Loss Coax(N-Male to N Male Ends)(0.08 db loss) Jumper Coax - Can be used to connect a splitter behind an amplier.EXTENSION CABLE CHARTRG 58 - FME connectors / 9913 - N connectorsOperation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
8                      For more options visitwww.wilsonelectronics.com15 DAYMONEY BACKGUARANTEEAll Wilson products have a 15 day money backguarantee with Proof of Purchase1 YEAR WARRANTYThe Wilson amplifier is warranted for one year against defects in workmanship and/or materials and will be repaired or replaced, at the discretion of the manufac-turer, to the original purchaser with dated proof of purchase or sales receipt.If you have questions about your amplifier please call technical support call 1-866-294-1660 or E-mail tech@wilsonelectronics.comMost warranty cases can be handled by taking the amplifier and the re-ceipt to the store where it was purchased. If inconvenient, the amplifier and a copy of the receipt, may be sent to the factory, at purchasers expense, where it may be repaired or replaced and returned shipping paid. Warranty does not cover damages caused by abuse, misuse, and negligence.ANTENNA OPTIONS

Navigation menu